| fw_config |
| field AUDIO_CODEC_SOURCE 40 42 |
| option AUDIO_CODEC_UNPROVISIONED 0 |
| option AUDIO_CODEC_ALC5682 1 |
| option AUDIO_CODEC_ALC5682I_VS 2 |
| end |
| field TS_DRIVER_SOURCE 43 45 |
| option TS_UNPROVISIONED 0 |
| option TS_ELAN0001 1 |
| option TS_ELAN2513 2 |
| end |
| end |
| chip soc/intel/jasperlake |
| |
| # USB Port Configuration |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # Camera |
| |
| register "SerialIoI2cMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| [PchSerialIoIndexI2C5] = PchSerialIoDisabled, |
| }" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Trackpad | |
| #| I2C1 | | |
| #| I2C2 | Touchscreen | |
| #| I2C3 | | |
| #| I2C4 | Audio | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 185, |
| .scl_hcnt = 95, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 185, |
| .scl_hcnt = 95, |
| .sda_hold = 40, |
| } |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 185, |
| .scl_hcnt = 95, |
| .sda_hold = 40, |
| } |
| }, |
| }" |
| |
| # Power limit config |
| register "power_limits_config[JSL_N4500_6W_CORE]" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 15, |
| }" |
| |
| register "power_limits_config[JSL_N6000_6W_CORE]" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 15, |
| }" |
| |
| register "power_limits_config[JSL_N5100_6W_CORE]" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 15, |
| }" |
| |
| # Enable Acoustic noise mitigation and set slew rate to 1/4 |
| # Rest of the parameters are 0 by default. |
| register "AcousticNoiseMitigation" = "1" |
| register "SlowSlewRate" = "SlewRateFastBy4" |
| register "FastPkgCRampDisable" = "1" |
| |
| device domain 0 on |
| device pci 04.0 on |
| chip drivers/intel/dptf |
| register "options.tsr[0].desc" = ""Memory"" |
| register "options.tsr[1].desc" = ""Ambient"" |
| register "options.tsr[2].desc" = ""Charger"" |
| register "options.tsr[3].desc" = ""5V regulator"" |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 80, 1000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 70, 4000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 51, 1000), |
| [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 75, 5000), |
| [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 60, 1000) |
| }" |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 105, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 105, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 105, SHUTDOWN), |
| [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 105, SHUTDOWN) |
| }" |
| ## Power Limits Control |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 3800, |
| .max_power = 5800, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 15000, |
| .max_power = 15000, |
| .time_window_min = 1 * MSECS_PER_SEC, |
| .time_window_max = 1 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 3000 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| device generic 0 on end |
| end |
| end # SA Thermal device |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Discrete Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H19)" |
| device usb 2.4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Integrated Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H19)" |
| device usb 2.7 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 15.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_EDGE_LOW(GPP_B3_IRQ)" |
| register "wake" = "GPE0_DW0_03" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| end #I2C 0 |
| device pci 15.1 off end #I2C 1 |
| device pci 15.2 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0001"" |
| register "desc" = ""ELAN Touchscreen"" |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "detect" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D5)" |
| register "reset_delay_ms" = "20" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "enable_delay_ms" = "1" |
| register "has_power_resource" = "1" |
| device i2c 10 on |
| probe TS_DRIVER_SOURCE TS_UNPROVISIONED |
| probe TS_DRIVER_SOURCE TS_ELAN0001 |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN2513"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D5)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on |
| probe TS_DRIVER_SOURCE TS_ELAN2513 |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GTCH7503"" |
| register "generic.desc" = ""G2TOUCH Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D5)" |
| register "generic.reset_delay_ms" = "50" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 40 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GDIX0000"" |
| register "generic.desc" = ""Goodix Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D4_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D5)" |
| register "generic.reset_delay_ms" = "120" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D6)" |
| register "generic.enable_delay_ms" = "12" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x5d on end |
| end |
| end # I2C 2 |
| device pci 15.3 off end #I2C 3 |
| device pci 1c.7 on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_DW2_03" |
| device pci 00.0 on end |
| end |
| end # PCI Express Root Port 8 - WLAN |
| device pci 19.0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_UNPROVISIONED |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682 |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_D16)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe AUDIO_CODEC_SOURCE AUDIO_CODEC_ALC5682I_VS |
| end |
| end |
| end #I2C 4 |
| device pci 1f.3 on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98360A"" |
| register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D17)" |
| device generic 0 on end |
| end |
| end # Intel HDA |
| end |
| end |