| uses CONFIG_HAVE_MP_TABLE |
| uses CONFIG_CBFS |
| uses CONFIG_HAVE_PIRQ_TABLE |
| uses CONFIG_USE_FALLBACK_IMAGE |
| uses CONFIG_HAVE_FALLBACK_BOOT |
| uses CONFIG_HAVE_HARD_RESET |
| uses CONFIG_HAVE_OPTION_TABLE |
| uses CONFIG_USE_OPTION_TABLE |
| uses CONFIG_ROM_PAYLOAD |
| uses CONFIG_IRQ_SLOT_COUNT |
| uses CONFIG_MAINBOARD |
| uses CONFIG_MAINBOARD_VENDOR |
| uses CONFIG_MAINBOARD_PART_NUMBER |
| uses COREBOOT_EXTRA_VERSION |
| uses CONFIG_ARCH |
| uses CONFIG_FALLBACK_SIZE |
| uses CONFIG_STACK_SIZE |
| uses CONFIG_HEAP_SIZE |
| uses CONFIG_ROM_SIZE |
| uses CONFIG_ROM_SECTION_SIZE |
| uses CONFIG_ROM_IMAGE_SIZE |
| uses CONFIG_ROM_SECTION_SIZE |
| uses CONFIG_ROM_SECTION_OFFSET |
| uses CONFIG_ROM_PAYLOAD_START |
| uses CONFIG_PAYLOAD_SIZE |
| uses CONFIG_ROMBASE |
| uses CONFIG_RAMBASE |
| uses CONFIG_XIP_ROM_SIZE |
| uses CONFIG_XIP_ROM_BASE |
| uses CONFIG_HAVE_MP_TABLE |
| uses CONFIG_CROSS_COMPILE |
| uses CC |
| uses HOSTCC |
| uses CONFIG_OBJCOPY |
| uses CONFIG_DEFAULT_CONSOLE_LOGLEVEL |
| uses CONFIG_MAXIMUM_CONSOLE_LOGLEVEL |
| uses CONFIG_CONSOLE_SERIAL8250 |
| uses CONFIG_TTYS0_BAUD |
| uses CONFIG_TTYS0_BASE |
| uses CONFIG_TTYS0_LCS |
| uses CONFIG_UDELAY_TSC |
| uses CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2 |
| uses CONFIG_CONSOLE_VGA |
| uses CONFIG_PCI_ROM_RUN |
| uses CONFIG_COMPRESSED_PAYLOAD_LZMA |
| uses CONFIG_COMPRESSED_PAYLOAD_NRV2B |
| uses CONFIG_PRECOMPRESSED_PAYLOAD |
| uses CONFIG_VIDEO_MB |
| uses CONFIG_PIRQ_ROUTE |
| |
| ## CONFIG_ROM_SIZE is the size of boot ROM that this board will use. |
| default CONFIG_ROM_SIZE = 256*1024 |
| |
| ### |
| ### Build options |
| ### |
| |
| #VGA Console |
| default CONFIG_CONSOLE_VGA=1 |
| default CONFIG_PCI_ROM_RUN=1 |
| |
| ## |
| ## Build code for the fallback boot |
| ## |
| default CONFIG_HAVE_FALLBACK_BOOT=0 |
| |
| ## |
| ## no MP table |
| ## |
| default CONFIG_HAVE_MP_TABLE=0 |
| |
| ## |
| ## Build code to reset the motherboard from coreboot |
| ## |
| default CONFIG_HAVE_HARD_RESET=0 |
| |
| ## Delay timer options |
| ## |
| default CONFIG_UDELAY_TSC=1 |
| default CONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2=1 |
| |
| ## |
| ## Build code to export a programmable irq routing table |
| ## |
| default CONFIG_HAVE_PIRQ_TABLE=1 |
| default CONFIG_IRQ_SLOT_COUNT=7 |
| default CONFIG_PIRQ_ROUTE=1 |
| #object irq_tables.o |
| |
| ## |
| ## Build code to export a CMOS option table |
| ## |
| default CONFIG_HAVE_OPTION_TABLE=1 |
| |
| ### |
| ### coreboot layout values |
| ### |
| |
| ## CONFIG_ROM_IMAGE_SIZE is the amount of space to allow coreboot to occupy. |
| default CONFIG_ROM_IMAGE_SIZE = 65536 |
| default CONFIG_FALLBACK_SIZE = CONFIG_ROM_IMAGE_SIZE |
| |
| ## |
| ## Use a small 8K stack |
| ## |
| default CONFIG_STACK_SIZE=0x2000 |
| |
| ## |
| ## Use a small 16K heap |
| ## |
| default CONFIG_HEAP_SIZE=0x4000 |
| |
| ## |
| ## Only use the option table in a normal image |
| ## |
| #default CONFIG_USE_OPTION_TABLE = !CONFIG_USE_FALLBACK_IMAGE |
| default CONFIG_USE_OPTION_TABLE = 0 |
| |
| default CONFIG_RAMBASE = 0x00004000 |
| |
| default CONFIG_ROM_PAYLOAD = 1 |
| |
| ## |
| ## The default compiler |
| ## |
| default CONFIG_CROSS_COMPILE="" |
| default CC="$(CONFIG_CROSS_COMPILE)gcc -m32" |
| default HOSTCC="gcc" |
| |
| ## |
| ## The Serial Console |
| ## |
| |
| # To Enable the Serial Console |
| default CONFIG_CONSOLE_SERIAL8250=1 |
| |
| ## Select the serial console baud rate |
| default CONFIG_TTYS0_BAUD=115200 |
| #default CONFIG_TTYS0_BAUD=57600 |
| #default CONFIG_TTYS0_BAUD=38400 |
| #default CONFIG_TTYS0_BAUD=19200 |
| #default CONFIG_TTYS0_BAUD=9600 |
| #default CONFIG_TTYS0_BAUD=4800 |
| #default CONFIG_TTYS0_BAUD=2400 |
| #default CONFIG_TTYS0_BAUD=1200 |
| |
| # Select the serial console base port |
| default CONFIG_TTYS0_BASE=0x3f8 |
| |
| # Select the serial protocol |
| # This defaults to 8 data bits, 1 stop bit, and no parity |
| default CONFIG_TTYS0_LCS=0x3 |
| |
| ## |
| ### Select the coreboot loglevel |
| ## |
| ## EMERG 1 system is unusable |
| ## ALERT 2 action must be taken immediately |
| ## CRIT 3 critical conditions |
| ## ERR 4 error conditions |
| ## WARNING 5 warning conditions |
| ## NOTICE 6 normal but significant condition |
| ## INFO 7 informational |
| ## CONFIG_DEBUG 8 debug-level messages |
| ## SPEW 9 Way too many details |
| |
| ## Request this level of debugging output |
| default CONFIG_DEFAULT_CONSOLE_LOGLEVEL=8 |
| |
| ## At a maximum only compile in this level of debugging |
| default CONFIG_MAXIMUM_CONSOLE_LOGLEVEL=8 |
| |
| default CONFIG_VIDEO_MB = 0 |
| |
| |
| # |
| # CBFS |
| # |
| # |
| default CONFIG_CBFS=1 |
| end |