| # SPDX-License-Identifier: GPL-2.0-only |
| |
| chip northbridge/amd/agesa/family14/root_complex |
| device cpu_cluster 0 on |
| chip cpu/amd/agesa/family14 |
| device lapic 0 on end |
| end |
| end |
| device domain 0 on |
| subsystemid 0x1022 0x1510 inherit |
| chip northbridge/amd/agesa/family14 |
| device pci 0.0 on end # Root Complex |
| device pci 1.0 on end # Internal Graphics P2P bridge 0x980[2456] |
| device pci 4.0 on end # PCIE P2P bridge on-board NIC |
| device pci 5.0 off end # PCIE P2P bridge |
| device pci 6.0 on end # PCIE P2P bridge PCIe slot |
| device pci 7.0 off end # PCIE P2P bridge |
| device pci 8.0 off end # NB/SB Link P2P bridge |
| end # agesa northbridge |
| |
| chip southbridge/amd/cimx/sb800 |
| device pci 11.0 on end # SATA |
| device pci 12.0 on end # OHCI USB 0-4 |
| device pci 12.2 on end # EHCI USB 0-4 |
| device pci 13.0 on end # OHCI USB 5-9 |
| device pci 13.2 on end # EHCI USB 5-9 |
| device pci 14.0 on end # SM |
| device pci 14.1 on end # IDE 0x439c |
| device pci 14.2 on end # HDA 0x4383 |
| device pci 14.3 on # LPC 0x439d |
| chip superio/fintek/f81865f |
| device pnp 4e.0 off # Floppy |
| io 0x60 = 0x3f0 |
| irq 0x70 = 6 |
| drq 0x74 = 2 |
| end |
| device pnp 4e.3 off end # Parallel Port |
| device pnp 4e.4 off end # Hardware Monitor |
| device pnp 4e.5 on # Keyboard |
| io 0x60 = 0x60 |
| io 0x62 = 0x64 |
| irq 0x70 = 1 |
| end |
| device pnp 4e.6 off end # GPIO |
| device pnp 4e.a off end # PME |
| device pnp 4e.10 on # COM1 |
| io 0x60 = 0x3f8 |
| irq 0x70 = 4 |
| end |
| device pnp 4e.11 on # COM2 |
| io 0x60 = 0x2f8 |
| irq 0x70 = 3 |
| end |
| end # f81865f |
| end #LPC |
| device pci 14.4 on end # PCIB 0x4384, NOTE: PCI interface pins shared with GPIO {GPIO 35:0} |
| device pci 14.5 off end # OHCI FS/LS USB |
| device pci 14.6 off end # Hudson-E1 GbE MAC: Broadcom BCM5785 (14E4:1699) |
| device pci 15.0 off end # PCIe PortA |
| device pci 15.1 off end # PCIe PortB |
| device pci 15.2 off end # PCIe PortC |
| device pci 15.3 off end # PCIe PortD |
| device pci 16.0 off end # OHCI USB 10-13 |
| device pci 16.2 off end # EHCI USB 10-13 |
| register "gpp_configuration" = "0" #4:0:0:0 (really need to disable all 4 somehow) |
| register "boot_switch_sata_ide" = "0" # 0: boot from SATA. 1: IDE |
| |
| #set up SB800 Fan control registers and IMC fan controls |
| register "imc_port_address" = "0x6E" # 0x2E and 0x6E are common |
| register "fan0_enabled" = "1" |
| register "fan1_enabled" = "1" |
| register "imc_fan_zone0_enabled" = "1" |
| register "imc_fan_zone1_enabled" = "1" |
| |
| register "fan0_config_vals" = "{ \ |
| FAN_INPUT_INTERNAL_DIODE, FAN_POLARITY_HIGH, \ |
| FREQ_25KHZ, 0x08, 0x00, 0x00, 0x00, 0x00,\ |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }" |
| register "fan1_config_vals" = "{ \ |
| FAN_INPUT_INTERNAL_DIODE, FAN_POLARITY_HIGH, \ |
| FREQ_25KHZ, 0x10, 0x00, 0x00, 0x00, 0x00, \ |
| 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00 }" |
| |
| register "imc_zone0_mode1" = " \ |
| IMC_MODE1_FAN_ENABLED | IMC_MODE1_FAN_IMC_CONTROLLED | \ |
| IMC_MODE1_FAN_STEP_MODE | IMC_MODE1_FANOUT0" |
| register "imc_zone0_mode2" = " IMC_MODE2_TEMPIN_SB_TSI | \ |
| IMC_MODE2_FANIN0 | IMC_MODE2_TEMP_AVERAGING_DISABLED" |
| register "imc_zone0_temp_offset" = "0x00" # No temp offset |
| register "imc_zone0_hysteresis" = "0x05" # Degrees C Hysteresis |
| register "imc_zone0_smbus_addr" = "0x98" # Temp Sensor SMBus address |
| register "imc_zone0_smbus_num" = "IMC_TEMP_SENSOR_ON_SMBUS_3" # SMBUS number |
| register "imc_zone0_pwm_step" = "0x01" # Fan PWM stepping rate |
| register "imc_zone0_ramping" = "0x00" # Disable Fan PWM ramping and stepping |
| |
| register "imc_zone1_mode1" = " \ |
| IMC_MODE1_FAN_ENABLED | IMC_MODE1_FAN_IMC_CONTROLLED | \ |
| IMC_MODE1_FAN_STEP_MODE | IMC_MODE1_FANOUT1" |
| register "imc_zone1_mode2" = " IMC_MODE2_TEMPIN_SB_TSI | \ |
| IMC_MODE2_FANIN1 | IMC_MODE2_TEMP_AVERAGING_DISABLED" |
| register "imc_zone1_temp_offset" = "0x00" # No temp offset |
| register "imc_zone1_hysteresis" = "0x05" # Degrees C Hysteresis |
| register "imc_zone1_smbus_addr" = "0x98" # Temp Sensor SMBus address |
| register "imc_zone1_smbus_num" = "IMC_TEMP_SENSOR_ON_SMBUS_3" # SMBUS number |
| register "imc_zone1_pwm_step" = "0x01" # Fan PWM stepping rate |
| register "imc_zone1_ramping" = "0x00" # Disable Fan PWM ramping and stepping |
| |
| # T56N has a Maximum operating temperature of 90C |
| # ZONEX_THRESHOLDS - _AC0 - _AC7, _CRT - Temp Threshold in degrees C |
| # ZONEX_FANSPEEDS - Fan speeds as a "percentage" |
| register "imc_zone0_thresholds" = "{ 87, 82, 77, 72, 65, 1, 0, 0, 90 }" |
| register "imc_zone0_fanspeeds" = "{100, 7, 5, 4, 3, 2, 0, 0 }" |
| register "imc_zone1_thresholds" = "{ 85, 80, 75, 65, 1, 0, 0, 0, 90 }" |
| register "imc_zone1_fanspeeds" = "{100, 10, 6, 4, 3, 0, 0, 0 }" |
| |
| end #southbridge/amd/cimx/sb800 |
| |
| chip northbridge/amd/agesa/family14 |
| |
| # These seem unnecessary |
| device pci 18.0 on end |
| device pci 18.1 on end |
| device pci 18.2 on end |
| device pci 18.3 on end |
| device pci 18.4 on end |
| device pci 18.5 on end |
| device pci 18.6 on end |
| device pci 18.7 on end |
| |
| register "spdAddrLookup" = " |
| { |
| { {0xA0, 0xA2}, {0x00, 0x00}, }, // socket 0 - Channel 0 & 1 - 8-bit SPD addresses |
| { {0x00, 0x00}, {0x00, 0x00}, }, // socket 1 - Channel 0 & 1 - 8-bit SPD addresses |
| }" |
| |
| end # agesa northbridge |
| |
| end #domain |
| end #northbridge/amd/agesa/family14/root_complex |