| chip soc/intel/tigerlake |
| # USB Port Config |
| register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)" # Type-A Port A0 |
| register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # Type-A / Type-C C1 |
| register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # M.2 Camera |
| register "usb2_ports[8]" = "USB2_PORT_MID(OC_SKIP)" # Type-A / Type-C C0 |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # M.2 Bluetooth |
| |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC1)" # USB3/2 Type A port A0 |
| |
| register "SaGv" = "SaGv_Disabled" |
| # I2C Port Config |
| register "SerialIoI2cMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| device domain 0 on |
| # Baseboard has these on, so they must be disabled here. |
| device ref tbt_pcie_rp0 off end |
| device ref tbt_pcie_rp1 off end |
| device ref tbt_dma0 off end |
| |
| device ref i2c0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_F8)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GDIX0000"" |
| register "generic.desc" = ""Goodix Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" |
| # Parameter T3 >= 10ms |
| register "generic.reset_delay_ms" = "120" |
| # Parameter T2 >= 1ms |
| register "generic.reset_off_delay_ms" = "3" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" |
| # Parameter T1 >= 10ms |
| register "generic.enable_delay_ms" = "12" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E3)" |
| # Parameter T4 >= 1ms |
| register "generic.stop_off_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 14 on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" |
| register "wake" = "GPE0_DW2_15" |
| register "probed" = "1" |
| device i2c 15 on end |
| end |
| end |
| end |
| end |