| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2006 Tyan |
| * Copyright (C) 2006 AMD |
| * Written by Yinghai Lu <yinghailu@gmail.com> for Tyan and AMD. |
| * |
| * Copyright (C) 2007 University of Mannheim |
| * Written by Philipp Degler <pdegler@rumms.uni-mannheim.de> for University of Mannheim |
| * Copyright (C) 2009 University of Heidelberg |
| * Written by Mondrian Nuessle <nuessle@uni-heidelberg.de> for University of Heidelberg |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #define FAM10_SCAN_PCI_BUS 0 |
| #define FAM10_ALLOCATE_IO_RANGE 1 |
| |
| #include <stdint.h> |
| #include <string.h> |
| #include <device/pci_def.h> |
| #include <device/pci_ids.h> |
| #include <arch/io.h> |
| #include <device/pnp_def.h> |
| #include <cpu/x86/lapic.h> |
| #include "option_table.h" |
| #include <console/console.h> |
| #include <timestamp.h> |
| #include <cpu/amd/model_10xxx_rev.h> |
| #include <lib.h> |
| #include <spd.h> |
| #include <delay.h> |
| #include <cpu/x86/lapic.h> |
| #include <superio/serverengines/pilot/pilot.h> |
| #include <superio/nsc/pc87417/pc87417.h> |
| #include <cpu/x86/bist.h> |
| #include <cpu/amd/car.h> |
| #include <northbridge/amd/amdfam10/raminit.h> |
| #include <northbridge/amd/amdht/ht_wrapper.h> |
| #include <cpu/amd/family_10h-family_15h/init_cpus.h> |
| #include <arch/early_variables.h> |
| #include <cbmem.h> |
| #include "southbridge/broadcom/bcm5785/early_smbus.c" |
| #include "southbridge/broadcom/bcm5785/early_setup.c" |
| |
| #include "cpu/amd/quadcore/quadcore.c" |
| |
| #define SERIAL_DEV PNP_DEV(0x2e, PILOT_SP1) |
| #define RTC_DEV PNP_DEV(0x4e, PC87417_RTC) |
| |
| void activate_spd_rom(const struct mem_controller *ctrl); |
| int spd_read_byte(unsigned device, unsigned address); |
| extern struct sys_info sysinfo_car; |
| |
| inline void activate_spd_rom(const struct mem_controller *ctrl) |
| { |
| u8 val; |
| outb(0x3d, 0x0cd6); |
| outb(0x87, 0x0cd7); |
| |
| outb(0x44, 0xcd6); |
| val = inb(0xcd7); |
| outb((val & ~3) | ctrl->spd_switch_addr, 0xcd7); |
| } |
| |
| inline int spd_read_byte(unsigned device, unsigned address) |
| { |
| return smbus_read_byte(device, address); |
| } |
| |
| static const u8 spd_addr[] = { |
| // switch addr, 1A addr, 2A addr, 3A addr, 4A addr, 1B addr, 2B addr, 3B addr 4B addr |
| //first node |
| RC00, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, |
| #if CONFIG_MAX_PHYSICAL_CPUS > 1 |
| //second node |
| RC01, DIMM0, DIMM2, 0, 0, DIMM1, DIMM3, 0, 0, |
| #endif |
| }; |
| |
| void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) |
| { |
| struct sys_info *sysinfo = &sysinfo_car; |
| u32 bsp_apicid = 0, val; |
| msr_t msr; |
| |
| timestamp_init(timestamp_get()); |
| timestamp_add_now(TS_START_ROMSTAGE); |
| |
| if (!cpu_init_detectedx && boot_cpu()) { |
| /* Nothing special needs to be done to find bus 0 */ |
| /* Allow the HT devices to be found */ |
| /* mov bsp to bus 0xff when > 8 nodes */ |
| set_bsp_node_CHtExtNodeCfgEn(); |
| enumerate_ht_chain(); |
| bcm5785_enable_lpc(); |
| pc87417_enable_dev(RTC_DEV); /* Enable RTC */ |
| } |
| |
| post_code(0x30); |
| |
| if (bist == 0) |
| bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); |
| |
| pilot_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); |
| |
| console_init(); |
| |
| /* Halt if there was a built in self test failure */ |
| report_bist_failure(bist); |
| |
| pilot_early_init(SERIAL_DEV); //config port is being taken from SERIAL_DEV |
| |
| val = cpuid_eax(1); |
| printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val); |
| printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1); |
| printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid); |
| printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx); |
| |
| /* Setup sysinfo defaults */ |
| set_sysinfo_in_ram(0); |
| |
| update_microcode(val); |
| |
| post_code(0x33); |
| |
| cpuSetAMDMSR(0); |
| post_code(0x34); |
| |
| amd_ht_init(sysinfo); |
| post_code(0x35); |
| |
| /* Setup nodes PCI space and start core 0 AP init. */ |
| finalize_node_setup(sysinfo); |
| |
| post_code(0x36); |
| |
| /* wait for all the APs core0 started by finalize_node_setup. */ |
| /* FIXME: A bunch of cores are going to start output to serial at once. |
| * It would be nice to fixup prink spinlocks for ROM XIP mode. |
| * I think it could be done by putting the spinlock flag in the cache |
| * of the BSP located right after sysinfo. |
| */ |
| |
| wait_all_core0_started(); |
| |
| #if IS_ENABLED(CONFIG_LOGICAL_CPUS) |
| /* Core0 on each node is configured. Now setup any additional cores. */ |
| printk(BIOS_DEBUG, "start_other_cores()\n"); |
| start_other_cores(bsp_apicid); |
| post_code(0x37); |
| wait_all_other_cores_started(bsp_apicid); |
| #endif |
| |
| #if IS_ENABLED(CONFIG_SET_FIDVID) |
| msr = rdmsr(0xc0010071); |
| printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo); |
| |
| /* FIXME: The sb fid change may survive the warm reset and only |
| * need to be done once.*/ |
| |
| enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn); |
| |
| post_code(0x39); |
| |
| if (!warm_reset_detect(0)) { // BSP is node 0 |
| init_fidvid_bsp(bsp_apicid, sysinfo->nodes); |
| } else { |
| init_fidvid_stage2(bsp_apicid, 0); // BSP is node 0 |
| } |
| |
| post_code(0x3A); |
| |
| /* show final fid and vid */ |
| msr = rdmsr(0xc0010071); |
| printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo); |
| #endif |
| |
| init_timer(); |
| |
| /* Reset for HT, FIDVID, PLL and errata changes to take affect. */ |
| if (!warm_reset_detect(0)) { |
| printk(BIOS_INFO, "...WARM RESET...\n\n\n"); |
| soft_reset(); |
| die("After soft_reset - shouldn't see this message!!!\n"); |
| } |
| |
| /* It's the time to set ctrl in sysinfo now; */ |
| fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr); |
| enable_smbus(); |
| |
| //do we need apci timer, tsc...., only debug need it for better output |
| /* all ap stopped? */ |
| // init_timer(); // Need to use TMICT to synchronize FID/VID |
| |
| timestamp_add_now(TS_BEFORE_INITRAM); |
| printk(BIOS_DEBUG, "raminit_amdmct()\n"); |
| raminit_amdmct(sysinfo); |
| timestamp_add_now(TS_AFTER_INITRAM); |
| |
| cbmem_initialize_empty(); |
| post_code(0x41); |
| |
| amdmct_cbmem_store_info(sysinfo); |
| |
| bcm5785_early_setup(); |
| } |
| |
| /** |
| * BOOL AMD_CB_ManualBUIDSwapList(u8 Node, u8 Link, u8 **List) |
| * Description: |
| * This routine is called every time a non-coherent chain is processed. |
| * BUID assignment may be controlled explicitly on a non-coherent chain. Provide a |
| * swap list. The first part of the list controls the BUID assignment and the |
| * second part of the list provides the device to device linking. Device orientation |
| * can be detected automatically, or explicitly. See documentation for more details. |
| * |
| * Automatic non-coherent init assigns BUIDs starting at 1 and incrementing sequentially |
| * based on each device's unit count. |
| * |
| * Parameters: |
| * @param[in] node = The node on which this chain is located |
| * @param[in] link = The link on the host for this chain |
| * @param[out] List = supply a pointer to a list |
| */ |
| BOOL AMD_CB_ManualBUIDSwapList (u8 node, u8 link, const u8 **List) |
| { |
| static const u8 swaplist[] = { 0xFF, CONFIG_HT_CHAIN_UNITID_BASE, CONFIG_HT_CHAIN_END_UNITID_BASE, 0xFF }; |
| /* If the BUID was adjusted in early_ht we need to do the manual override */ |
| if ((CONFIG_HT_CHAIN_UNITID_BASE != 0) && (CONFIG_HT_CHAIN_END_UNITID_BASE != 0)) { |
| printk(BIOS_DEBUG, "AMD_CB_ManualBUIDSwapList()\n"); |
| if ((node == 0) && (link == 0)) { /* BSP SB link */ |
| *List = swaplist; |
| return 1; |
| } |
| } |
| |
| return 0; |
| } |