| /* SPDX-License-Identifier: GPL-2.0-only */ |
| /* This file is part of the coreboot project. */ |
| |
| #include <device/mmio.h> |
| #include <device/pci_ops.h> |
| #include <cbmem.h> |
| #include <console/console.h> |
| #include <device/device.h> |
| #include <device/pci.h> |
| #include <device/pci_ids.h> |
| #include <reg_script.h> |
| |
| #include <soc/iomap.h> |
| #include <soc/iosf.h> |
| #include <soc/lpc.h> |
| #include <soc/nvs.h> |
| #include <soc/pattrs.h> |
| #include <soc/pci_devs.h> |
| #include <soc/pm.h> |
| #include <soc/ramstage.h> |
| #include "chip.h" |
| |
| /* |
| * The LPE audio devices needs 1MiB of memory reserved aligned to a 512MiB |
| * address. Just take 1MiB @ 512MiB. |
| */ |
| #define FIRMWARE_PHYS_BASE (512 << 20) |
| #define FIRMWARE_PHYS_LENGTH (2 << 20) |
| #define FIRMWARE_PCI_REG_BASE 0xa8 |
| #define FIRMWARE_PCI_REG_LENGTH 0xac |
| #define FIRMWARE_REG_BASE_C0 0x144000 |
| #define FIRMWARE_REG_LENGTH_C0 (FIRMWARE_REG_BASE_C0 + 4) |
| |
| static void assign_device_nvs(struct device *dev, u32 *field, |
| unsigned int index) |
| { |
| struct resource *res; |
| |
| res = find_resource(dev, index); |
| if (res) |
| *field = res->base; |
| } |
| |
| static void lpe_enable_acpi_mode(struct device *dev) |
| { |
| static const struct reg_script ops[] = { |
| /* Disable PCI interrupt, enable Memory and Bus Master */ |
| REG_PCI_OR32(PCI_COMMAND, |
| PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER | PCI_COMMAND_INT_DISABLE), |
| |
| /* Enable ACPI mode */ |
| REG_IOSF_OR(IOSF_PORT_0x58, LPE_PCICFGCTR1, |
| LPE_PCICFGCTR1_PCI_CFG_DIS | LPE_PCICFGCTR1_ACPI_INT_EN), |
| |
| REG_SCRIPT_END |
| }; |
| global_nvs_t *gnvs; |
| |
| /* Find ACPI NVS to update BARs */ |
| gnvs = cbmem_find(CBMEM_ID_ACPI_GNVS); |
| if (!gnvs) { |
| printk(BIOS_ERR, "Unable to locate Global NVS\n"); |
| return; |
| } |
| |
| /* Save BAR0, BAR1, and firmware base to ACPI NVS */ |
| assign_device_nvs(dev, &gnvs->dev.lpe_bar0, PCI_BASE_ADDRESS_0); |
| assign_device_nvs(dev, &gnvs->dev.lpe_bar1, PCI_BASE_ADDRESS_2); |
| assign_device_nvs(dev, &gnvs->dev.lpe_fw, FIRMWARE_PCI_REG_BASE); |
| |
| /* Device is enabled in ACPI mode */ |
| gnvs->dev.lpe_en = 1; |
| |
| /* Put device in ACPI mode */ |
| reg_script_run_on_dev(dev, ops); |
| } |
| |
| static void setup_codec_clock(struct device *dev) |
| { |
| uint32_t reg; |
| u32 *clk_reg; |
| struct soc_intel_braswell_config *config; |
| const char *freq_str; |
| |
| config = config_of(dev); |
| switch (config->lpe_codec_clk_src) { |
| case LPE_CLK_SRC_XTAL: |
| /* XTAL driven bit2=0 */ |
| freq_str = "19.2MHz External Crystal"; |
| reg = CLK_SRC_XTAL; |
| break; |
| |
| case LPE_CLK_SRC_PLL: |
| /* PLL driven bit2=1 */ |
| freq_str = "19.2MHz PLL"; |
| reg = CLK_SRC_PLL; |
| break; |
| |
| default: |
| reg = CLK_SRC_XTAL; |
| printk(BIOS_DEBUG, "LPE codec clock default to using Crystal\n"); |
| return; |
| } |
| |
| /* Default to always running. */ |
| reg |= CLK_CTL_ON; |
| |
| |
| printk(BIOS_DEBUG, "LPE Audio codec clock set to %sMHz.\n", freq_str); |
| |
| clk_reg = (u32 *)(PMC_BASE_ADDRESS + PLT_CLK_CTL_0); |
| |
| write32(clk_reg, (read32(clk_reg) & ~0x7) | reg); |
| } |
| |
| static void lpe_stash_firmware_info(struct device *dev) |
| { |
| struct resource *res; |
| struct resource *mmio; |
| |
| res = find_resource(dev, FIRMWARE_PCI_REG_BASE); |
| if (res == NULL) { |
| printk(BIOS_DEBUG, "LPE Firmware memory not found.\n"); |
| return; |
| } |
| printk(BIOS_DEBUG, "LPE FW Resource: 0x%08x\n", (u32) res->base); |
| |
| /* Continue using old way of informing firmware address / size. */ |
| pci_write_config32(dev, FIRMWARE_PCI_REG_BASE, res->base); |
| pci_write_config32(dev, FIRMWARE_PCI_REG_LENGTH, res->size); |
| |
| /* Also put the address in MMIO space like on C0 BTM */ |
| mmio = find_resource(dev, PCI_BASE_ADDRESS_0); |
| write32((void *)(uintptr_t)(mmio->base + FIRMWARE_REG_BASE_C0), res->base); |
| write32((void *)(uintptr_t)(mmio->base + FIRMWARE_REG_LENGTH_C0), res->size); |
| } |
| |
| |
| static void lpe_init(struct device *dev) |
| { |
| struct soc_intel_braswell_config *config = config_of(dev); |
| |
| printk(BIOS_SPEW, "%s/%s (%s)\n", __FILE__, __func__, dev_name(dev)); |
| |
| lpe_stash_firmware_info(dev); |
| setup_codec_clock(dev); |
| |
| if (config->lpe_acpi_mode) |
| lpe_enable_acpi_mode(dev); |
| } |
| |
| static void lpe_read_resources(struct device *dev) |
| { |
| struct resource *res; |
| pci_dev_read_resources(dev); |
| |
| /* |
| * Allocate the BAR1 resource at index 2 to fulfill the Windows driver |
| * interface requirements even though the PCI device has only one BAR |
| */ |
| res = new_resource(dev, PCI_BASE_ADDRESS_2); |
| res->base = 0; |
| res->size = 0x1000; |
| res->limit = 0xffffffff; |
| res->gran = 12; |
| res->align = 12; |
| res->flags = IORESOURCE_MEM; |
| |
| reserved_ram_resource(dev, FIRMWARE_PCI_REG_BASE, FIRMWARE_PHYS_BASE >> 10, |
| FIRMWARE_PHYS_LENGTH >> 10); |
| } |
| |
| static void lpe_set_resources(struct device *dev) |
| { |
| struct resource *res; |
| |
| res = find_resource(dev, PCI_BASE_ADDRESS_2); |
| if (res != NULL) |
| res->flags |= IORESOURCE_STORED; |
| |
| pci_dev_set_resources(dev); |
| } |
| |
| static const struct device_operations device_ops = { |
| .read_resources = lpe_read_resources, |
| .set_resources = lpe_set_resources, |
| .enable_resources = pci_dev_enable_resources, |
| .init = lpe_init, |
| .ops_pci = &soc_pci_ops, |
| }; |
| |
| static const struct pci_driver southcluster __pci_driver = { |
| .ops = &device_ops, |
| .vendor = PCI_VENDOR_ID_INTEL, |
| .device = LPE_DEVID, |
| }; |