| /* SPDX-License-Identifier: GPL-2.0-or-later */ |
| |
| #include <acpi/acpigen.h> |
| #include <acpi/acpi_device.h> |
| #include <console/console.h> |
| #include <device/device.h> |
| #include <device/pci_ids.h> |
| #include <device/pci_ops.h> |
| #include <device/pci.h> |
| #include <intelblocks/pmc.h> |
| #include <intelblocks/pmc_ipc.h> |
| #include "chip.h" |
| |
| /* |
| * The "ExternalFacingPort" and "HotPlugSupportInD3" properties are defined at |
| * https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports |
| */ |
| #define PCIE_EXTERNAL_PORT_UUID "EFCC06CC-73AC-4BC3-BFF0-76143807C389" |
| #define PCIE_EXTERNAL_PORT_PROPERTY "ExternalFacingPort" |
| |
| #define PCIE_HOTPLUG_IN_D3_UUID "6211E2C0-58A3-4AF3-90E1-927A4E0C55A4" |
| #define PCIE_HOTPLUG_IN_D3_PROPERTY "HotPlugSupportInD3" |
| |
| /* |
| * This UUID and the resulting ACPI Device Property is defined by the |
| * Power Management for Storage Hardware Devices: |
| * |
| * https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/power-management-for-storage-hardware-devices-intro |
| */ |
| #define PCIE_RTD3_STORAGE_UUID "5025030F-842F-4AB4-A561-99A5189762D0" |
| #define PCIE_RTD3_STORAGE_PROPERTY "StorageD3Enable" |
| |
| /* PCIe Root Port registers for link status and L23 control. */ |
| #define PCH_PCIE_CFG_LSTS 0x52 /* Link Status Register */ |
| #define PCH_PCIE_CFG_SPR 0xe0 /* Scratchpad */ |
| #define PCH_PCIE_CFG_RPPGEN 0xe2 /* Root Port Power Gating Enable */ |
| #define PCH_PCIE_CFG_LCAP_PN 0x4f /* Root Port Number */ |
| |
| /* ACPI register names corresponding to PCIe root port registers. */ |
| #define ACPI_REG_PCI_LINK_ACTIVE "LASX" /* Link active status */ |
| #define ACPI_REG_PCI_L23_RDY_ENTRY "L23E" /* L23_Rdy Entry Request */ |
| #define ACPI_REG_PCI_L23_RDY_DETECT "L23R" /* L23_Rdy Detect Transition */ |
| #define ACPI_REG_PCI_L23_SAVE_STATE "NCB7" /* Scratch bit to save L23 state */ |
| |
| /* Called from _ON to get PCIe link back to active state. */ |
| static void pcie_rtd3_acpi_l23_exit(void) |
| { |
| /* Skip if port is not in L2/L3. */ |
| acpigen_write_if_lequal_namestr_int(ACPI_REG_PCI_L23_SAVE_STATE, 1); |
| |
| /* Initiate L2/L3 Ready To Detect transition. */ |
| acpigen_write_store_int_to_namestr(1, ACPI_REG_PCI_L23_RDY_DETECT); |
| |
| /* Wait for transition to detect. */ |
| acpigen_write_delay_until_namestr_int(320, ACPI_REG_PCI_L23_RDY_DETECT, 0); |
| |
| acpigen_write_store_int_to_namestr(0, ACPI_REG_PCI_L23_SAVE_STATE); |
| |
| /* Once in detect, wait for link active. */ |
| acpigen_write_delay_until_namestr_int(128, ACPI_REG_PCI_LINK_ACTIVE, 1); |
| |
| acpigen_pop_len(); /* If */ |
| } |
| |
| /* Called from _OFF to put PCIe link into L2/L3 state. */ |
| static void pcie_rtd3_acpi_l23_entry(void) |
| { |
| /* Initiate L2/L3 Entry request. */ |
| acpigen_write_store_int_to_namestr(1, ACPI_REG_PCI_L23_RDY_ENTRY); |
| |
| /* Wait for L2/L3 Entry request to clear. */ |
| acpigen_write_delay_until_namestr_int(128, ACPI_REG_PCI_L23_RDY_ENTRY, 0); |
| |
| acpigen_write_store_int_to_namestr(1, ACPI_REG_PCI_L23_SAVE_STATE); |
| } |
| |
| static void |
| pcie_rtd3_acpi_method_on(unsigned int pcie_rp, |
| const struct soc_intel_common_block_pcie_rtd3_config *config) |
| { |
| acpigen_write_method_serialized("_ON", 0); |
| |
| /* Assert enable GPIO to turn on device power. */ |
| if (config->enable_gpio.pin_count) { |
| acpigen_enable_tx_gpio(&config->enable_gpio); |
| if (config->enable_delay_ms) |
| acpigen_write_sleep(config->enable_delay_ms); |
| } |
| |
| /* Enable SRCCLK for root port if pin is defined. */ |
| if (config->srcclk_pin >= 0) |
| pmc_ipc_acpi_set_pci_clock(pcie_rp, config->srcclk_pin, true); |
| |
| /* De-assert reset GPIO to bring device out of reset. */ |
| if (config->reset_gpio.pin_count) { |
| acpigen_disable_tx_gpio(&config->reset_gpio); |
| if (config->reset_delay_ms) |
| acpigen_write_sleep(config->reset_delay_ms); |
| } |
| |
| /* Trigger L23 ready exit flow unless disabld by config. */ |
| if (!config->disable_l23) |
| pcie_rtd3_acpi_l23_exit(); |
| |
| acpigen_pop_len(); /* Method */ |
| } |
| |
| static void |
| pcie_rtd3_acpi_method_off(int pcie_rp, |
| const struct soc_intel_common_block_pcie_rtd3_config *config) |
| { |
| acpigen_write_method_serialized("_OFF", 0); |
| |
| /* Trigger L23 ready entry flow unless disabled by config. */ |
| if (!config->disable_l23) |
| pcie_rtd3_acpi_l23_entry(); |
| |
| /* Assert reset GPIO to place device into reset. */ |
| if (config->reset_gpio.pin_count) { |
| acpigen_enable_tx_gpio(&config->reset_gpio); |
| if (config->reset_off_delay_ms) |
| acpigen_write_sleep(config->reset_off_delay_ms); |
| } |
| |
| /* Disable SRCCLK for this root port if pin is defined. */ |
| if (config->srcclk_pin >= 0) |
| pmc_ipc_acpi_set_pci_clock(pcie_rp, config->srcclk_pin, false); |
| |
| /* De-assert enable GPIO to turn off device power. */ |
| if (config->enable_gpio.pin_count) { |
| acpigen_disable_tx_gpio(&config->enable_gpio); |
| if (config->enable_off_delay_ms) |
| acpigen_write_sleep(config->enable_off_delay_ms); |
| } |
| |
| acpigen_pop_len(); /* Method */ |
| } |
| |
| static void |
| pcie_rtd3_acpi_method_status(int pcie_rp, |
| const struct soc_intel_common_block_pcie_rtd3_config *config) |
| { |
| const struct acpi_gpio *gpio; |
| |
| acpigen_write_method("_STA", 0); |
| |
| /* Use enable GPIO for status if provided, otherwise use reset GPIO. */ |
| if (config->enable_gpio.pin_count) |
| gpio = &config->enable_gpio; |
| else |
| gpio = &config->reset_gpio; |
| |
| /* Read current GPIO value into Local0. */ |
| acpigen_get_tx_gpio(gpio); |
| |
| /* Ensure check works for both active low and active high GPIOs. */ |
| acpigen_write_store_int_to_op(gpio->active_low, LOCAL1_OP); |
| |
| acpigen_write_if_lequal_op_op(LOCAL0_OP, LOCAL1_OP); |
| acpigen_write_return_op(ZERO_OP); |
| acpigen_write_else(); |
| acpigen_write_return_op(ONE_OP); |
| acpigen_pop_len(); /* Else */ |
| |
| acpigen_pop_len(); /* Method */ |
| } |
| |
| static void pcie_rtd3_acpi_fill_ssdt(const struct device *dev) |
| { |
| const struct soc_intel_common_block_pcie_rtd3_config *config = config_of(dev); |
| static const char *const power_res_states[] = {"_PR0"}; |
| const struct device *parent = dev->bus->dev; |
| const char *scope = acpi_device_path(parent); |
| const struct opregion opregion = OPREGION("PXCS", PCI_CONFIG, 0, 0xff); |
| const struct fieldlist fieldlist[] = { |
| FIELDLIST_OFFSET(PCH_PCIE_CFG_LSTS), |
| FIELDLIST_RESERVED(13), |
| FIELDLIST_NAMESTR(ACPI_REG_PCI_LINK_ACTIVE, 1), |
| FIELDLIST_OFFSET(PCH_PCIE_CFG_SPR), |
| FIELDLIST_RESERVED(7), |
| FIELDLIST_NAMESTR(ACPI_REG_PCI_L23_SAVE_STATE, 1), |
| FIELDLIST_OFFSET(PCH_PCIE_CFG_RPPGEN), |
| FIELDLIST_RESERVED(2), |
| FIELDLIST_NAMESTR(ACPI_REG_PCI_L23_RDY_ENTRY, 1), |
| FIELDLIST_NAMESTR(ACPI_REG_PCI_L23_RDY_DETECT, 1), |
| }; |
| uint8_t pcie_rp; |
| struct acpi_dp *dsd, *pkg; |
| |
| if (!is_dev_enabled(parent)) { |
| printk(BIOS_ERR, "%s: root port not enabled\n", __func__); |
| return; |
| } |
| if (!scope) { |
| printk(BIOS_ERR, "%s: root port scope not found\n", __func__); |
| return; |
| } |
| if (!config->enable_gpio.pin_count && !config->reset_gpio.pin_count) { |
| printk(BIOS_ERR, "%s: Enable and/or Reset GPIO required for %s.\n", |
| __func__, scope); |
| return; |
| } |
| if (config->srcclk_pin > CONFIG_MAX_PCIE_CLOCK_SRC) { |
| printk(BIOS_ERR, "%s: Invalid clock pin %u for %s.\n", __func__, |
| config->srcclk_pin, scope); |
| return; |
| } |
| |
| /* Read port number of root port that this device is attached to. */ |
| pcie_rp = pci_read_config8(parent, PCH_PCIE_CFG_LCAP_PN); |
| if (pcie_rp == 0 || pcie_rp > CONFIG_MAX_ROOT_PORTS) { |
| printk(BIOS_ERR, "%s: Invalid root port number: %u\n", __func__, pcie_rp); |
| return; |
| } |
| /* Port number is 1-based, PMC IPC method expects 0-based. */ |
| pcie_rp--; |
| |
| printk(BIOS_INFO, "%s: Enable RTD3 for %s (%s)\n", scope, dev_path(parent), |
| config->desc ?: dev->chip_ops->name); |
| |
| /* The RTD3 power resource is added to the root port, not the device. */ |
| acpigen_write_scope(scope); |
| |
| if (config->desc) |
| acpigen_write_name_string("_DDN", config->desc); |
| |
| acpigen_write_opregion(&opregion); |
| acpigen_write_field("PXCS", fieldlist, ARRAY_SIZE(fieldlist), |
| FIELD_ANYACC | FIELD_NOLOCK | FIELD_PRESERVE); |
| |
| /* ACPI Power Resource for controlling the attached device power. */ |
| acpigen_write_power_res("RTD3", 0, 0, power_res_states, ARRAY_SIZE(power_res_states)); |
| pcie_rtd3_acpi_method_status(pcie_rp, config); |
| pcie_rtd3_acpi_method_on(pcie_rp, config); |
| pcie_rtd3_acpi_method_off(pcie_rp, config); |
| acpigen_pop_len(); /* PowerResource */ |
| |
| /* Indicate to the OS that device supports hotplug in D3. */ |
| dsd = acpi_dp_new_table("_DSD"); |
| pkg = acpi_dp_new_table(PCIE_HOTPLUG_IN_D3_UUID); |
| acpi_dp_add_integer(pkg, PCIE_HOTPLUG_IN_D3_PROPERTY, 1); |
| acpi_dp_add_package(dsd, pkg); |
| |
| /* Indicate to the OS if the device provides an External facing port. */ |
| if (config->is_external) { |
| pkg = acpi_dp_new_table(PCIE_EXTERNAL_PORT_UUID); |
| acpi_dp_add_integer(pkg, PCIE_EXTERNAL_PORT_PROPERTY, 1); |
| acpi_dp_add_package(dsd, pkg); |
| } |
| acpi_dp_write(dsd); |
| |
| /* |
| * Check the sibling device on the root port to see if it is storage class and add the |
| * property for the OS to enable storage D3, or allow it to be enabled by config. |
| */ |
| if (config->is_storage |
| || (dev->sibling && (dev->sibling->class >> 16) == PCI_BASE_CLASS_STORAGE)) { |
| acpigen_write_device(acpi_device_name(dev)); |
| acpigen_write_ADR(0); |
| acpigen_write_STA(ACPI_STATUS_DEVICE_ALL_ON); |
| acpigen_write_name_integer("_S0W", 4); |
| |
| dsd = acpi_dp_new_table("_DSD"); |
| pkg = acpi_dp_new_table(PCIE_RTD3_STORAGE_UUID); |
| acpi_dp_add_integer(pkg, PCIE_RTD3_STORAGE_PROPERTY, 1); |
| acpi_dp_add_package(dsd, pkg); |
| acpi_dp_write(dsd); |
| |
| acpigen_pop_len(); /* Device */ |
| |
| printk(BIOS_INFO, "%s: Added StorageD3Enable property\n", scope); |
| } |
| |
| acpigen_pop_len(); /* Scope */ |
| } |
| |
| static const char *pcie_rtd3_acpi_name(const struct device *dev) |
| { |
| /* Attached device name must be "PXSX" for the Linux Kernel to recognize it. */ |
| return "PXSX"; |
| } |
| |
| static struct device_operations pcie_rtd3_ops = { |
| .read_resources = noop_read_resources, |
| .set_resources = noop_set_resources, |
| .acpi_fill_ssdt = pcie_rtd3_acpi_fill_ssdt, |
| .acpi_name = pcie_rtd3_acpi_name, |
| }; |
| |
| static void pcie_rtd3_acpi_enable(struct device *dev) |
| { |
| dev->ops = &pcie_rtd3_ops; |
| } |
| |
| struct chip_operations soc_intel_common_block_pcie_rtd3_ops = { |
| CHIP_NAME("Intel PCIe Runtime D3") |
| .enable_dev = pcie_rtd3_acpi_enable |
| }; |