| # SPDX-License-Identifier: GPL-2.0-or-later |
| |
| chip northbridge/intel/sandybridge |
| # XMM1: CH0S0 0x50 |
| # XMM3: CH1S0 0x52 |
| register "spd_addresses" = "{0x50, 0, 0x52, 0}" |
| |
| device domain 0x0 on |
| subsystemid 0x103c 0x2abf inherit |
| |
| device ref peg10 on end |
| device ref igd on end |
| |
| chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH |
| register "gen1_dec" = "0x003c0a01" |
| register "pcie_port_coalesce" = "1" |
| register "sata_interface_speed_support" = "0x3" |
| # SATA0: ata1 0x01 |
| # SATA1: ata2 0x02 |
| # SATA2: ata5 0x10 |
| # SATA3: ata6 0x20 |
| register "sata_port_map" = "0x33" |
| register "spi_lvscc" = "0x2005" |
| register "spi_uvscc" = "0x2005" |
| device ref ehci2 on end |
| device ref hda on end |
| device ref pcie_rp2 on end # MINI_PCIE |
| device ref pcie_rp3 on end # PCIEx1_1 |
| device ref pcie_rp4 on end # PCIEx1_2 |
| device ref pcie_rp5 on end # PCIEx1_3 |
| device ref pcie_rp6 on end # RTL8171EH |
| device ref ehci1 on end |
| device ref lpc on |
| chip superio/ite/it8772f |
| # GPIO registers all zero or written by LED code |
| |
| register "ec.smbus_en" = "1" |
| |
| register "TMPIN1.mode" = "THERMAL_MODE_DISABLED" |
| register "TMPIN2.mode" = "THERMAL_DIODE" # Near ATX_CPU connector |
| register "TMPIN3.mode" = "THERMAL_PECI" |
| # TMPIN3.offset is set to TJ_MAX at runtime |
| |
| # CPU fan |
| register "FAN2.mode" = "FAN_SMART_AUTOMATIC" |
| register "FAN2.smart.tmpin" = "3" |
| register "FAN2.smart.tmp_off" = "-127" |
| register "FAN2.smart.tmp_start" = "40" |
| register "FAN2.smart.tmp_full" = "86" |
| register "FAN2.smart.tmp_delta" = "5" |
| register "FAN2.smart.pwm_start" = "25" |
| register "FAN2.smart.slope" = "6" |
| # System fan |
| register "FAN3.mode" = "FAN_SMART_AUTOMATIC" |
| register "FAN3.smart.tmpin" = "3" |
| register "FAN3.smart.tmp_off" = "-127" |
| register "FAN3.smart.tmp_start" = "40" |
| register "FAN3.smart.tmp_full" = "86" |
| register "FAN3.smart.tmp_delta" = "5" |
| register "FAN3.smart.pwm_start" = "34" |
| register "FAN3.smart.slope" = "11" |
| |
| register "FAN_VECA.tmpin" = "2" |
| register "FAN_VECA.fanout" = "2" |
| register "FAN_VECA.tmp_start" = "57" |
| register "FAN_VECA.tmp_delta" = "5" |
| register "FAN_VECA.slope" = "26" |
| |
| register "FAN_VECB.tmpin" = "2" |
| register "FAN_VECB.fanout" = "3" |
| register "FAN_VECB.tmp_start" = "48" |
| register "FAN_VECB.tmp_delta" = "5" |
| register "FAN_VECB.slope" = "5" |
| |
| register "ec.vin_mask" = "VIN_ALL" |
| |
| device pnp 2e.0 off end # FDC |
| device pnp 2e.1 off end # Serial Port 1 |
| device pnp 2e.4 on # Environment Controller |
| io 0x60 = 0xa30 |
| io 0x62 = 0xa20 |
| end |
| device pnp 2e.7 on # GPIO |
| io 0x60 = 0x0 |
| io 0x62 = 0xa00 |
| end |
| device pnp 2e.5 off end # Keyboard, enabled in vendor firmware but missing connector |
| device pnp 2e.6 off end # Mouse , enabled in vendor firmware but missing connector |
| device pnp 2e.a off end # IR |
| end |
| end |
| device ref sata1 on end |
| end |
| end |
| end |