| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2010 Advanced Micro Devices, Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| #ifndef SB800_H |
| #define SB800_H |
| |
| #include <device/pci_ids.h> |
| #include "chip.h" |
| |
| /* Power management index/data registers */ |
| #define BIOSRAM_INDEX 0xcd4 |
| #define BIOSRAM_DATA 0xcd5 |
| #define PM_INDEX 0xcd6 |
| #define PM_DATA 0xcd7 |
| #define PM2_INDEX 0xcd0 |
| #define PM2_DATA 0xcd1 |
| |
| #define SB800_ACPI_IO_BASE 0x800 |
| |
| #define ACPI_PM_EVT_BLK (SB800_ACPI_IO_BASE + 0x00) /* 4 bytes */ |
| #define ACPI_PM1_CNT_BLK (SB800_ACPI_IO_BASE + 0x04) /* 2 bytes */ |
| #define ACPI_PMA_CNT_BLK (SB800_ACPI_IO_BASE + 0x0F) /* 1 byte */ |
| #define ACPI_PM_TMR_BLK (SB800_ACPI_IO_BASE + 0x18) /* 4 bytes */ |
| #define ACPI_GPE0_BLK (SB800_ACPI_IO_BASE + 0x10) /* 8 bytes */ |
| #define ACPI_CPU_CONTROL (SB800_ACPI_IO_BASE + 0x08) /* 6 bytes */ |
| |
| extern void pm_iowrite(u8 reg, u8 value); |
| extern u8 pm_ioread(u8 reg); |
| extern void pm2_iowrite(u8 reg, u8 value); |
| extern u8 pm2_ioread(u8 reg); |
| extern void set_sm_enable_bits(device_t sm_dev, u32 reg_pos, u32 mask, u32 val); |
| |
| #define REV_SB800_A11 0x11 |
| #define REV_SB800_A12 0x12 |
| |
| void sb800_enable(device_t dev); |
| |
| #ifdef __PRE_RAM__ |
| void sb800_lpc_port80(void); |
| void sb800_pci_port80(void); |
| void sb800_clk_output_48Mhz(void); |
| #else |
| /* void sb800_setup_sata_phys(struct device *dev); */ |
| #endif |
| |
| int s3_save_nvram_early(u32 dword, int size, int nvram_pos); |
| int s3_load_nvram_early(int size, u32 *old_dword, int nvram_pos); |
| |
| void sb800_enable_usbdebug(unsigned int port); |
| |
| #endif /* SB800_H */ |