| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <bootblock_common.h> |
| #include <stdint.h> |
| #include <device/pnp_ops.h> |
| #include <device/pnp.h> |
| #include <northbridge/intel/sandybridge/raminit.h> |
| #include <northbridge/intel/sandybridge/raminit_native.h> |
| #include <northbridge/intel/sandybridge/sandybridge.h> |
| #include <southbridge/intel/bd82x6x/pch.h> |
| #include <superio/ite/it8783ef/it8783ef.h> |
| #include <superio/ite/common/ite.h> |
| |
| void bootblock_mainboard_early_init(void) |
| { |
| const pnp_devfn_t dev = PNP_DEV(0x2e, IT8783EF_GPIO); |
| |
| pnp_enter_conf_state(dev); |
| pnp_set_logical_device(dev); |
| |
| pnp_write_config(dev, 0x23, ITE_UART_CLK_PREDIVIDE_24); |
| |
| /* Switch multi function for UART4 */ |
| pnp_write_config(dev, 0x2a, 0x04); |
| /* Switch multi function for UART3 */ |
| pnp_write_config(dev, 0x2c, 0x13); |
| |
| /* No GPIOs used: Clear any output / pull-up that's set by default */ |
| pnp_write_config(dev, 0xb8, 0x00); |
| pnp_write_config(dev, 0xc0, 0x00); |
| pnp_write_config(dev, 0xc3, 0x00); |
| pnp_write_config(dev, 0xc8, 0x00); |
| pnp_write_config(dev, 0xcb, 0x00); |
| pnp_write_config(dev, 0xef, 0x00); |
| |
| pnp_exit_conf_state(dev); |
| } |
| |
| void mainboard_fill_pei_data(struct pei_data *const pei_data) |
| { |
| const struct pei_data pei_data_template = { |
| .pei_version = PEI_VERSION, |
| .mchbar = DEFAULT_MCHBAR, |
| .dmibar = DEFAULT_DMIBAR, |
| .epbar = DEFAULT_EPBAR, |
| .pciexbar = CONFIG_MMCONF_BASE_ADDRESS, |
| .smbusbar = CONFIG_FIXED_SMBUS_IO_BASE, |
| .wdbbar = 0x4000000, |
| .wdbsize = 0x1000, |
| .hpet_address = CONFIG_HPET_ADDRESS, |
| .rcba = (uintptr_t)DEFAULT_RCBA, |
| .pmbase = DEFAULT_PMBASE, |
| .gpiobase = DEFAULT_GPIOBASE, |
| .thermalbase = 0xfed08000, |
| .system_type = 0, // 0 Mobile, 1 Desktop/Server |
| .tseg_size = CONFIG_SMM_TSEG_SIZE, |
| .spd_addresses = { 0xA0, 0xA2, 0xA4, 0xA6 }, |
| .ts_addresses = { 0x00, 0x00, 0x00, 0x00 }, |
| .ec_present = 1, |
| .gbe_enable = 1, |
| .ddr3lv_support = 0, |
| // 0 = leave channel enabled |
| // 1 = disable dimm 0 on channel |
| // 2 = disable dimm 1 on channel |
| // 3 = disable dimm 0+1 on channel |
| .dimm_channel0_disabled = 0, |
| .dimm_channel1_disabled = 0, |
| .max_ddr3_freq = 1600, |
| .usb_port_config = { |
| /* Enabled / OC PIN / Length */ |
| { 1, 0, 0x0080 }, /* P00: 1st (left) USB3 (OC #0) */ |
| { 1, 0, 0x0080 }, /* P01: 2nd (left) USB3 (OC #0) */ |
| { 1, 1, 0x0080 }, /* P02: 1st Multibay USB3 (OC #1) */ |
| { 1, 1, 0x0080 }, /* P03: 2nd Multibay USB3 (OC #1) */ |
| { 1, 8, 0x0040 }, /* P04: MiniPCIe 1 USB2 (no OC) */ |
| { 1, 8, 0x0040 }, /* P05: MiniPCIe 2 USB2 (no OC) */ |
| { 1, 8, 0x0040 }, /* P06: USB Hub x4 USB2 (no OC) */ |
| { 1, 8, 0x0040 }, /* P07: MiniPCIe 4 USB2 (no OC) */ |
| { 1, 8, 0x0080 }, /* P08: SD card reader USB2 (no OC) */ |
| { 1, 4, 0x0080 }, /* P09: 3rd (right) USB2 (OC #4) */ |
| { 1, 5, 0x0040 }, /* P10: 4th (right) USB2 (OC #5) */ |
| { 1, 8, 0x0040 }, /* P11: 3rd Multibay USB2 (no OC) */ |
| { 1, 8, 0x0080 }, /* P12: misc internal USB2 (no OC) */ |
| { 1, 6, 0x0080 }, /* P13: misc internal USB2 (OC #6) */ |
| }, |
| .usb3 = { |
| .mode = 3, /* Smart Auto? */ |
| .hs_port_switch_mask = 0xf, /* All four ports. */ |
| .preboot_support = 1, /* preOS driver? */ |
| .xhci_streams = 1, /* Enable. */ |
| }, |
| .pcie_init = 1, |
| }; |
| *pei_data = pei_data_template; |
| } |
| |
| const struct southbridge_usb_port mainboard_usb_ports[] = { |
| /* Enabled / Power / OC PIN */ |
| { 1, 1, 0 }, /* P00: 1st (left) USB3 (OC #0) */ |
| { 1, 1, 0 }, /* P01: 2nd (left) USB3 (OC #0) */ |
| { 1, 1, 1 }, /* P02: 1st Multibay USB3 (OC #1) */ |
| { 1, 1, 1 }, /* P03: 2nd Multibay USB3 (OC #1) */ |
| { 1, 0, 8 }, /* P04: MiniPCIe 1 USB2 (no OC) */ |
| { 1, 0, 8 }, /* P05: MiniPCIe 2 USB2 (no OC) */ |
| { 1, 0, 8 }, /* P06: USB Hub x4 USB2 (no OC) */ |
| { 1, 0, 8 }, /* P07: MiniPCIe 4 USB2 (no OC) */ |
| { 1, 1, 8 }, /* P08: SD card reader USB2 (no OC) */ |
| { 1, 1, 4 }, /* P09: 3rd (right) USB2 (OC #4) */ |
| { 1, 0, 5 }, /* P10: 4th (right) USB2 (OC #5) */ |
| { 1, 0, 8 }, /* P11: 3rd Multibay USB2 (no OC) */ |
| { 1, 1, 8 }, /* P12: misc internal USB2 (no OC) */ |
| { 1, 1, 6 }, /* P13: misc internal USB2 (OC #6) */ |
| }; |
| |
| void mainboard_get_spd(spd_raw_data *spd, bool id_only) |
| { |
| read_spd(&spd[0], 0x50, id_only); |
| read_spd(&spd[1], 0x51, id_only); |
| read_spd(&spd[2], 0x52, id_only); |
| read_spd(&spd[3], 0x53, id_only); |
| } |