| chip soc/intel/tigerlake |
| # BitMask where bits [3:0] are Controller 0 Channel [3:0] and |
| # bits [7:4] are Controller 1 Channel [3:0]. |
| # Enable Command Mirroring for controller 0 channel 0 and 1, |
| # and controller 1 channel 0 and 1. |
| register "CmdMirror" = "0x00000033" |
| |
| register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)" # Type-A / Type-C Port 0 |
| register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC1)" # Type-A / Type-C Port 1 |
| register "usb2_ports[2]" = "USB2_PORT_TYPE_C(OC1)" # Type-A / Type-C Port 1 |
| register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # Front Camera |
| register "usb2_ports[4]" = "USB2_PORT_TYPE_C(OC0)" # Type-A / Type-C Port 0 |
| |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-A / Type-C Port 0 |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC1)" # Type-A / Type-C Port 1 |
| |
| # Disable SRCCLKREQ1# |
| register "PcieClkSrcUsage[1]" = "PCIE_CLK_NOTUSED" |
| |
| device domain 0 on |
| device ref dptf on |
| chip drivers/intel/dptf |
| ## Disable Active Policy |
| register "policies.active" = "{[0] = {.target=DPTF_NONE}}" |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 85, 1000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 65, 6000), |
| [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_0, 65, 6000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 65, 6000), |
| [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 65, 6000)}" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 100, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 75, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 75, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 75, SHUTDOWN), |
| [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 75, SHUTDOWN)}" |
| |
| ## Power Limits Control |
| # 3-9W PL1 in 200mW increments, avg over 28-32s interval |
| # PL2 ranges from 9 to 40W, avg over 28-32s interval |
| register "controls.power_limits" = "{ |
| .pl1 = {.min_power = 3000, |
| .max_power = 9000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200,}, |
| .pl2 = {.min_power = 40000, |
| .max_power = 40000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000,}}" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 }}" |
| |
| device generic 0 on end |
| end |
| end |
| device ref i2c0 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_R5)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| end |
| end |
| chip drivers/i2c/max98373 |
| register "vmon_slot_no" = "0" |
| register "imon_slot_no" = "1" |
| register "uid" = "0" |
| register "desc" = ""Right Speaker Amp"" |
| register "name" = ""MAXR"" |
| device i2c 31 on |
| probe AUDIO MAX98373_ALC5682I_I2S_UP4 |
| end |
| end |
| chip drivers/i2c/max98373 |
| register "vmon_slot_no" = "2" |
| register "imon_slot_no" = "3" |
| register "uid" = "1" |
| register "desc" = ""Left Speaker Amp"" |
| register "name" = ""MAXL"" |
| device i2c 32 on |
| probe AUDIO MAX98373_ALC5682I_I2S_UP4 |
| end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN90FC"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_F16)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN2700"" |
| register "generic.desc" = ""ELAN Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" |
| register "generic.wake" = "GPE0_DW2_15" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 15 on end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref hda on |
| probe AUDIO MAX98357_ALC5682I_I2S |
| probe AUDIO MAX98373_ALC5682I_I2S |
| probe AUDIO MAX98373_ALC5682_SNDW |
| probe AUDIO MAX98373_ALC5682I_I2S_UP4 |
| probe AUDIO MAX98360_ALC5682I_I2S |
| end |
| device ref pcie_rp9 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B2)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "srcclk_pin" = "0" |
| device generic 0 on end |
| end |
| end |
| # This variant has USB4/PCIe on both ports so RP0 must be enabled |
| # in order for hotplug resources to be assigned to Type-C Port C0. |
| device ref tbt_pcie_rp0 on |
| probe DB_USB USB4_GEN3 |
| end |
| device ref pmc hidden |
| # The pmc_mux chip driver is a placeholder for the |
| # PMC.MUX device in the ACPI hierarchy. |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port5 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| # SBU is fixed, HSL follows CC |
| register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port3 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| # SBU is fixed, HSL follows CC |
| register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref north_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(4, 2)" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(3, 2)" |
| device ref tcss_usb3_port2 on |
| probe DB_USB USB4_GEN3 |
| end |
| end |
| end |
| end |
| end |
| device ref south_xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device ref usb2_port2 on |
| probe DB_USB USB4_GEN3 |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(3, 1)" |
| device ref usb2_port3 on |
| probe DB_USB USB4_GEN3 |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(4, 1)" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A13)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device ref usb3_port2 on |
| probe DB_USB USB4_GEN3 |
| end |
| end |
| end |
| end |
| end |
| end |
| end |