| fw_config |
| field AUDIO_CODEC_SOURCE 41 43 |
| option AUDIO_CODEC_UNPROVISIONED 0 |
| option AUDIO_CODEC_ALC5682 1 |
| option AUDIO_CODEC_ALC5682I_VS 2 |
| end |
| end |
| chip soc/intel/tigerlake |
| register "DdiPort1Hpd" = "0" |
| register "DdiPort2Hpd" = "0" |
| |
| register "usb2_phy_sus_pg_disable" = "1" |
| |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Audio | |
| #| I2C1 | Touchscreen | |
| #| I2C2 | WLAN, SAR0 | |
| #| I2C3 | Camera, SAR1 | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 163, |
| .scl_hcnt = 75, |
| .sda_hold = 36, |
| }, |
| }, |
| }" |
| #These settings improve the USB2 Port1 eye diagram |
| register "usb2_ports[3]" = "{ |
| .enable = 1, |
| .tx_bias = USB2_BIAS_28P15MV, |
| .tx_emp_enable = USB2_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_56P3MV, |
| .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, |
| .type_c = 1, |
| }" |
| register "usb2_ports[8]" = "USB2_PORT_TYPE_C(OC_SKIP)" |
| |
| register "tcc_offset" = "8" |
| |
| register "power_limits_config[POWER_LIMITS_U_4_CORE]" = "{ |
| .tdp_pl1_override = 18, |
| .tdp_pl2_override = 51, |
| .tdp_pl4 = 105, |
| }" |
| |
| device domain 0 on |
| device pci 04.0 on |
| chip drivers/intel/dptf |
| ## Active Policy |
| register "policies.active" = "{ |
| [0] = {.target = DPTF_TEMP_SENSOR_3, |
| .thresholds = {TEMP_PCT(57, 90), |
| TEMP_PCT(47, 80), |
| TEMP_PCT(40, 70), |
| TEMP_PCT(36, 60), |
| TEMP_PCT(34, 50), |
| TEMP_PCT(30, 40),}}}" |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 6000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 75, 6000), |
| [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_0, 75, 6000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 6000), |
| [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 75, 6000)}" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 100, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 80, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 80, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 80, SHUTDOWN), |
| [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 80, SHUTDOWN)}" |
| |
| ## Power Limits Control |
| # 12-18W PL1 in 200mW increments, avg over 28-32s interval |
| # PL2 is 51W, avg over 28-32s interval |
| register "controls.power_limits" = "{ |
| .pl1 = {.min_power = 12000, |
| .max_power = 18000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200,}, |
| .pl2 = {.min_power = 51000, |
| .max_power = 51000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000,}}" |
| |
| ## Fan Performance Control (Percent, Speed, Noise, Power) |
| register "controls.fan_perf" = "{ |
| [0] = { 90, 5200, 220, 2200, }, |
| [1] = { 80, 4900, 180, 1800, }, |
| [2] = { 70, 4600, 145, 1450, }, |
| [3] = { 60, 4200, 115, 1150, }, |
| [4] = { 50, 3800, 90, 900, }, |
| [5] = { 40, 3400, 55, 550, }, |
| [6] = { 30, 2900, 30, 300, }, |
| [7] = { 20, 2300, 15, 150, }, |
| [8] = { 10, 1600, 10, 100, }, |
| [9] = { 0, 0, 0, 50, }}" |
| |
| # Fan options |
| register "options.fan.fine_grained_control" = "1" |
| register "options.fan.step_size" = "2" |
| |
| device generic 0 on end |
| end |
| end # DPTF 0x9A03 |
| device ref i2c0 on |
| chip drivers/i2c/generic |
| # register "hid" is set in variant.c because of FW_CONFIG |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_F8)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a alias audio_codec on end |
| end |
| chip drivers/i2c/max98373 |
| register "vmon_slot_no" = "0" |
| register "imon_slot_no" = "1" |
| register "uid" = "0" |
| register "desc" = ""Right Speaker Amp"" |
| register "name" = ""MAXR"" |
| device i2c 31 on end |
| end |
| chip drivers/i2c/max98373 |
| register "vmon_slot_no" = "2" |
| register "imon_slot_no" = "3" |
| register "uid" = "1" |
| register "desc" = ""Left Speaker Amp"" |
| register "name" = ""MAXL"" |
| device i2c 32 on end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9008"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.has_power_resource" = "1" |
| register "generic.disable_gpio_export_in_crs" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" |
| register "wake" = "GPE0_DW2_15" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref hda on |
| probe AUDIO MAX98357_ALC5682I_I2S |
| probe AUDIO MAX98373_ALC5682I_I2S |
| probe AUDIO MAX98373_ALC5682_SNDW |
| probe AUDIO MAX98373_ALC5682I_I2S_UP4 |
| probe AUDIO MAX98360_ALC5682I_I2S |
| end |
| device ref pcie_rp9 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B2)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" |
| register "srcclk_pin" = "0" |
| device generic 0 on end |
| end |
| end |
| device ref pmc hidden |
| # The pmc_mux chip driver is a placeholder for the |
| # PMC.MUX device in the ACPI hierarchy. |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port9 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| # SBU is fixed, HSL follows CC |
| register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port4 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| # SBU is fixed, HSL follows CC |
| register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref north_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(3, 2)" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device ref tcss_usb3_port2 on |
| probe DB_USB USB3_ACTIVE |
| end |
| end |
| end |
| end |
| end |
| device ref south_xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device ref usb2_port4 on |
| probe DB_USB USB3_ACTIVE |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(3, 1)" |
| device ref usb2_port9 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A13)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device ref usb3_port1 on end |
| end |
| end |
| end |
| end |
| end |
| end |