blob: 9edb550da5c711c6481018bb545a84916b3e97f9 [file] [log] [blame]
#ifndef PC80_MC146818RTC_H
#define PC80_MC146818RTC_H
#ifndef RTC_BASE_PORT
#define RTC_BASE_PORT 0x70
#endif
#define RTC_PORT(x) (RTC_BASE_PORT + (x))
/* control registers - Moto names
*/
#define RTC_REG_A 10
#define RTC_REG_B 11
#define RTC_REG_C 12
#define RTC_REG_D 13
/**********************************************************************
* register details
**********************************************************************/
#define RTC_FREQ_SELECT RTC_REG_A
/* update-in-progress - set to "1" 244 microsecs before RTC goes off the bus,
* reset after update (may take 1.984ms @ 32768Hz RefClock) is complete,
* totalling to a max high interval of 2.228 ms.
*/
# define RTC_UIP 0x80
# define RTC_DIV_CTL 0x70
/* divider control: refclock values 4.194 / 1.049 MHz / 32.768 kHz */
# define RTC_REF_CLCK_4MHZ 0x00
# define RTC_REF_CLCK_1MHZ 0x10
# define RTC_REF_CLCK_32KHZ 0x20
/* 2 values for divider stage reset, others for "testing purposes only" */
# define RTC_DIV_RESET1 0x60
# define RTC_DIV_RESET2 0x70
/* Periodic intr. / Square wave rate select. 0=none, 1=32.8kHz,... 15=2Hz */
# define RTC_RATE_SELECT 0x0F
# define RTC_RATE_NONE 0x00
# define RTC_RATE_32786HZ 0x01
# define RTC_RATE_16384HZ 0x02
# define RTC_RATE_8192HZ 0x03
# define RTC_RATE_4096HZ 0x04
# define RTC_RATE_2048HZ 0x05
# define RTC_RATE_1024HZ 0x06
# define RTC_RATE_512HZ 0x07
# define RTC_RATE_256HZ 0x08
# define RTC_RATE_128HZ 0x09
# define RTC_RATE_64HZ 0x0a
# define RTC_RATE_32HZ 0x0b
# define RTC_RATE_16HZ 0x0c
# define RTC_RATE_8HZ 0x0d
# define RTC_RATE_4HZ 0x0e
# define RTC_RATE_2HZ 0x0f
/**********************************************************************/
#define RTC_CONTROL RTC_REG_B
# define RTC_SET 0x80 /* disable updates for clock setting */
# define RTC_PIE 0x40 /* periodic interrupt enable */
# define RTC_AIE 0x20 /* alarm interrupt enable */
# define RTC_UIE 0x10 /* update-finished interrupt enable */
# define RTC_SQWE 0x08 /* enable square-wave output */
# define RTC_DM_BINARY 0x04 /* all time/date values are BCD if clear */
# define RTC_24H 0x02 /* 24 hour mode - else hours bit 7 means pm */
# define RTC_DST_EN 0x01 /* auto switch DST - works f. USA only */
/**********************************************************************/
#define RTC_INTR_FLAGS RTC_REG_C
/* caution - cleared by read */
# define RTC_IRQF 0x80 /* any of the following 3 is active */
# define RTC_PF 0x40
# define RTC_AF 0x20
# define RTC_UF 0x10
/**********************************************************************/
#define RTC_VALID RTC_REG_D
# define RTC_VRT 0x80 /* valid RAM and time */
/**********************************************************************/
/* On PCs, the checksum is built only over bytes 16..45 */
#define PC_CKS_RANGE_START 16
#define PC_CKS_RANGE_END 45
#define PC_CKS_LOC 46
/* Linux bios checksum is built only over bytes 49..125 */
#ifndef LB_CKS_RANGE_START
#define LB_CKS_RANGE_START 49
#endif
#ifndef LB_CKS_RANGE_END
#define LB_CKS_RANGE_END 125
#endif
#ifndef LB_CKS_LOC
#define LB_CKS_LOC 126
#endif
#if !defined(ASSEMBLY)
void rtc_init(int invalid);
int get_option(char *name, unsigned int *value);
int set_option(char *name, unsigned int value);
#endif
#endif /* PC80_MC146818RTC_H */