| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2005 Digital Design Corporation |
| * Copyright (C) 2006 Uwe Hermann <uwe@hermann-uwe.de> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| /* |
| * Serial Presence Detect (SPD) data stored on SDRAM modules. |
| * |
| * Datasheet: |
| * - Name: PC SDRAM Serial Presence Detect (SPD) Specification |
| * Revision 1.2A, December, 1997 |
| * - PDF: http://www.intel.com/design/chipsets/memory/spdsd12a.pdf |
| * |
| * Datasheet (alternative): |
| * - Name: SERIAL PRESENCE DETECT STANDARD, General Standard |
| * JEDEC Standard No. 21-C |
| * - PDF: http://www.jedec.org/download/search/4_01_02_00R9.PDF |
| */ |
| |
| #ifndef _SPD_H_ |
| #define _SPD_H_ |
| |
| /* Byte numbers. */ |
| #define SPD_NUM_MANUFACTURER_BYTES 0 /* Number of bytes used by module manufacturer */ |
| #define SPD_TOTAL_SPD_MEMORY_SIZE 1 /* Total SPD memory size */ |
| #define SPD_MEMORY_TYPE 2 /* (Fundamental) memory type */ |
| #define SPD_NUM_ROWS 3 /* Number of row address bits */ |
| #define SPD_NUM_COLUMNS 4 /* Number of column address bits */ |
| #define SPD_NUM_DIMM_BANKS 5 /* Number of module rows (banks) */ |
| #define SPD_MODULE_DATA_WIDTH_LSB 6 /* Module data width (LSB) */ |
| #define SPD_MODULE_DATA_WIDTH_MSB 7 /* Module data width (MSB) */ |
| #define SPD_MODULE_VOLTAGE 8 /* Module interface signal levels */ |
| #define SPD_MIN_CYCLE_TIME_AT_CAS_MAX 9 /* SDRAM cycle time (highest CAS latency), RAS access time (tRAC) */ |
| #define SPD_ACCESS_TIME_FROM_CLOCK 10 /* SDRAM access time from clock (highest CAS latency), CAS access time (Tac, tCAC) */ |
| #define SPD_DIMM_CONFIG_TYPE 11 /* Module configuration type */ |
| #define SPD_REFRESH 12 /* Refresh rate/type */ |
| #define SPD_PRIMARY_SDRAM_WIDTH 13 /* SDRAM width (primary SDRAM) */ |
| #define SPD_ERROR_CHECKING_SDRAM_WIDTH 14 /* Error checking SDRAM (data) width */ |
| #define SPD_MIN_CLOCK_DELAY_B2B_RAND_COLUMN 15 /* SDRAM device attributes, minimum clock delay for back to back random column */ |
| #define SPD_SUPPORTED_BURST_LENGTHS 16 /* SDRAM device attributes, burst lengths supported */ |
| #define SPD_NUM_BANKS_PER_SDRAM 17 /* SDRAM device attributes, number of banks on SDRAM device */ |
| #define SPD_ACCEPTABLE_CAS_LATENCIES 18 /* SDRAM device attributes, CAS latency */ |
| #define SPD_CS_LATENCY 19 /* SDRAM device attributes, CS latency */ |
| #define SPD_WE_LATENCY 20 /* SDRAM device attributes, WE latency */ |
| #define SPD_MODULE_ATTRIBUTES 21 /* SDRAM module attributes */ |
| #define SPD_DEVICE_ATTRIBUTES_GENERAL 22 /* SDRAM device attributes, general */ |
| #define SPD_SDRAM_CYCLE_TIME_2ND 23 /* SDRAM cycle time (2nd highest CAS latency) */ |
| #define SPD_ACCESS_TIME_FROM_CLOCK_2ND 24 /* SDRAM access from clock (2nd highest CAS latency) */ |
| #define SPD_SDRAM_CYCLE_TIME_3RD 25 /* SDRAM cycle time (3rd highest CAS latency) */ |
| #define SPD_ACCESS_TIME_FROM_CLOCK_3RD 26 /* SDRAM access from clock (3rd highest CAS latency) */ |
| #define SPD_MIN_ROW_PRECHARGE_TIME 27 /* Minimum row precharge time (Trp) */ |
| #define SPD_MIN_ROWACTIVE_TO_ROWACTIVE 28 /* Minimum row active to row active (Trrd) */ |
| #define SPD_MIN_RAS_TO_CAS_DELAY 29 /* Minimum RAS to CAS delay (Trcd) */ |
| #define SPD_MIN_ACTIVE_TO_PRECHARGE_DELAY 30 /* Minimum RAS pulse width (Tras) */ |
| #define SPD_DENSITY_OF_EACH_ROW_ON_MODULE 31 /* Density of each row on module */ |
| #define SPD_CMD_SIGNAL_INPUT_SETUP_TIME 32 /* Command and address signal input setup time */ |
| #define SPD_CMD_SIGNAL_INPUT_HOLD_TIME 33 /* Command and address signal input hold time */ |
| #define SPD_DATA_SIGNAL_INPUT_SETUP_TIME 34 /* Data signal input setup time */ |
| #define SPD_DATA_SIGNAL_INPUT_HOLD_TIME 35 /* Data signal input hold time */ |
| #define SPD_WRITE_RECOVERY_TIME 36 /* Write recovery time (tWR) */ |
| #define SPD_INT_WRITE_TO_READ_DELAY 37 /* Internal write to read command delay (tWTR) */ |
| #define SPD_INT_READ_TO_PRECHARGE_DELAY 38 /* Internal read to precharge command delay (tRTP) */ |
| #define SPD_MEM_ANALYSIS_PROBE_PARAMS 39 /* Memory analysis probe characteristics */ |
| #define SPD_BYTE_41_42_EXTENSION 40 /* Extension of byte 41 (tRC) and byte 42 (tRFC) */ |
| #define SPD_MIN_ACT_TO_ACT_AUTO_REFRESH 41 /* Minimum active to active auto refresh (tRCmin) */ |
| #define SPD_MIN_AUTO_REFRESH_TO_ACT 42 /* Minimum auto refresh to active/auto refresh (tRFC) */ |
| #define SPD_MAX_DEVICE_CYCLE_TIME 43 /* Maximum device cycle time (tCKmax) */ |
| #define SPD_MAX_DQS_DQ_SKEW 44 /* Maximum skew between DQS and DQ (tDQSQ) */ |
| #define SPD_MAX_READ_DATAHOLD_SKEW 45 /* Maximum read data-hold skew factor (tQHS) */ |
| #define SPD_PLL_RELOCK_TIME 46 /* PLL relock time */ |
| #define SPD_SPD_DATA_REVISION_CODE 62 /* SPD data revision code */ |
| #define SPD_CHECKSUM_FOR_BYTES_0_TO_62 63 /* Checksum for bytes 0-62 */ |
| #define SPD_MANUFACTURER_JEDEC_ID_CODE 64 /* Manufacturer's JEDEC ID code, per EIA/JEP106 (bytes 64-71) */ |
| #define SPD_MANUFACTURING_LOCATION 72 /* Manufacturing location */ |
| #define SPD_MANUFACTURER_PART_NUMBER 73 /* Manufacturer's part number, in 6-bit ASCII (bytes 73-90) */ |
| #define SPD_REVISION_CODE 91 /* Revision code (bytes 91-92) */ |
| #define SPD_MANUFACTURING_DATE 93 /* Manufacturing date (byte 93: year, byte 94: week) */ |
| #define SPD_ASSEMBLY_SERIAL_NUMBER 95 /* Assembly serial number (bytes 95-98) */ |
| #define SPD_MANUFACTURER_SPECIFIC_DATA 99 /* Manufacturer specific data (bytes 99-125) */ |
| #define SPD_INTEL_SPEC_FOR_FREQUENCY 126 /* Intel specification for frequency */ |
| #define SPD_INTEL_SPEC_100_MHZ 127 /* Intel specification details for 100MHz support */ |
| |
| /* DRAM specifications use the following naming conventions for SPD locations */ |
| #define SPD_tRP SPD_MIN_ROW_PRECHARGE_TIME |
| #define SPD_tRRD SPD_MIN_ROWACTIVE_TO_ROWACTIVE |
| #define SPD_tRCD SPD_MIN_RAS_TO_CAS_DELAY |
| #define SPD_tRAS SPD_MIN_ACTIVE_TO_PRECHARGE_DELAY |
| #define SPD_BANK_DENSITY SPD_DENSITY_OF_EACH_ROW_ON_MODULE |
| #define SPD_ADDRESS_CMD_HOLD SPD_CMD_SIGNAL_INPUT_HOLD_TIME |
| #define SPD_tRC 41 /* SDRAM Device Minimum Active to Active/Auto Refresh Time (tRC) */ |
| #define SPD_tRFC 42 /* SDRAM Device Minimum Auto Refresh to Active/Auto Refresh (tRFC) */ |
| |
| |
| /* SPD_MEMORY_TYPE values. */ |
| #define SPD_MEMORY_TYPE_FPM_DRAM 1 |
| #define SPD_MEMORY_TYPE_EDO 2 |
| #define SPD_MEMORY_TYPE_PIPELINED_NIBBLE 3 |
| #define SPD_MEMORY_TYPE_SDRAM 4 |
| #define SPD_MEMORY_TYPE_MULTIPLEXED_ROM 5 |
| #define SPD_MEMORY_TYPE_SGRAM_DDR 6 |
| #define SPD_MEMORY_TYPE_SDRAM_DDR 7 |
| #define SPD_MEMORY_TYPE_SDRAM_DDR2 8 |
| #define SPD_MEMORY_TYPE_SDRAM_DDR3 0xb |
| |
| /* SPD_MODULE_VOLTAGE values. */ |
| #define SPD_VOLTAGE_TTL 0 /* 5.0 Volt/TTL */ |
| #define SPD_VOLTAGE_LVTTL 1 /* LVTTL */ |
| #define SPD_VOLTAGE_HSTL 2 /* HSTL 1.5 */ |
| #define SPD_VOLTAGE_SSTL3 3 /* SSTL 3.3 */ |
| #define SPD_VOLTAGE_SSTL2 4 /* SSTL 2.5 */ |
| |
| /* SPD_DIMM_CONFIG_TYPE values. */ |
| #define ERROR_SCHEME_NONE 0 |
| #define ERROR_SCHEME_PARITY 1 |
| #define ERROR_SCHEME_ECC 2 |
| |
| /* SPD_ACCEPTABLE_CAS_LATENCIES values. */ |
| // TODO: Check values. |
| #define SPD_CAS_LATENCY_1_0 0x01 |
| #define SPD_CAS_LATENCY_1_5 0x02 |
| #define SPD_CAS_LATENCY_2_0 0x04 |
| #define SPD_CAS_LATENCY_2_5 0x08 |
| #define SPD_CAS_LATENCY_3_0 0x10 |
| #define SPD_CAS_LATENCY_3_5 0x20 |
| #define SPD_CAS_LATENCY_4_0 0x40 |
| |
| #define SPD_CAS_LATENCY_DDR2_3 (1 << 3) |
| #define SPD_CAS_LATENCY_DDR2_4 (1 << 4) |
| #define SPD_CAS_LATENCY_DDR2_5 (1 << 5) |
| #define SPD_CAS_LATENCY_DDR2_6 (1 << 6) |
| |
| /* SPD_SUPPORTED_BURST_LENGTHS values. */ |
| #define SPD_BURST_LENGTH_1 1 |
| #define SPD_BURST_LENGTH_2 2 |
| #define SPD_BURST_LENGTH_4 4 |
| #define SPD_BURST_LENGTH_8 8 |
| #define SPD_BURST_LENGTH_PAGE (1 << 7) |
| |
| /* SPD_MODULE_ATTRIBUTES values. */ |
| #define MODULE_BUFFERED 1 |
| #define MODULE_REGISTERED 2 |
| |
| /* DIMM SPD addresses */ |
| #define DIMM0 0x50 |
| #define DIMM1 0x51 |
| #define DIMM2 0x52 |
| #define DIMM3 0x53 |
| #define DIMM4 0x54 |
| #define DIMM5 0x55 |
| #define DIMM6 0x56 |
| #define DIMM7 0x57 |
| |
| #endif /* _SPD_H_ */ |
| |