| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <commonlib/helpers.h> |
| #include <console/console.h> |
| #include <device/mmio.h> |
| #include <device/pci_rom.h> |
| #include <device/resource.h> |
| #include <drivers/intel/gma/i915.h> |
| #include <drivers/intel/gma/i915_reg.h> |
| #include <intelblocks/graphics.h> |
| #include <soc/ramstage.h> |
| #include <soc/systemagent.h> |
| #include <types.h> |
| |
| void graphics_soc_panel_init(struct device *dev) |
| { |
| struct soc_intel_skylake_config *conf = config_of(dev); |
| const struct i915_gpu_panel_config *panel_cfg; |
| struct resource *mmio_res; |
| uint8_t *base; |
| u32 reg32; |
| |
| if (!conf) |
| return; |
| |
| panel_cfg = &conf->panel_cfg; |
| |
| mmio_res = find_resource(dev, PCI_BASE_ADDRESS_0); |
| if (!mmio_res || !mmio_res->base) |
| return; |
| base = (void *)(uintptr_t)mmio_res->base; |
| |
| reg32 = ((panel_cfg->up_delay_ms * 10) & 0x1fff) << 16; |
| reg32 |= (panel_cfg->backlight_on_delay_ms * 10) & 0x1fff; |
| write32(base + PCH_PP_ON_DELAYS, reg32); |
| |
| reg32 = ((panel_cfg->down_delay_ms * 10) & 0x1fff) << 16; |
| reg32 |= (panel_cfg->backlight_off_delay_ms * 10) & 0x1fff; |
| write32(base + PCH_PP_OFF_DELAYS, reg32); |
| |
| reg32 = read32(base + PCH_PP_DIVISOR); |
| reg32 &= ~0x1f; |
| reg32 |= (DIV_ROUND_UP(panel_cfg->cycle_delay_ms, 100) + 1) & 0x1f; |
| write32(base + PCH_PP_DIVISOR, reg32); |
| |
| /* So far all devices seem to use the PCH PWM function. |
| The CPU PWM registers are all zero after reset. */ |
| if (panel_cfg->backlight_pwm_hz) { |
| /* Reference clock is 24MHz. We can choose either a 16 |
| or a 128 step increment. Use 16 if we would have less |
| than 100 steps otherwise. */ |
| const unsigned int hz_limit = 24 * 1000 * 1000 / 128 / 100; |
| unsigned int pwm_increment, pwm_period; |
| u32 south_chicken1; |
| |
| south_chicken1 = read32(base + SOUTH_CHICKEN1); |
| if (panel_cfg->backlight_pwm_hz > hz_limit) { |
| pwm_increment = 16; |
| south_chicken1 &= ~1; |
| } else { |
| pwm_increment = 128; |
| south_chicken1 |= 1; |
| } |
| write32(base + SOUTH_CHICKEN1, south_chicken1); |
| |
| pwm_period = 24 * 1000 * 1000 / pwm_increment / panel_cfg->backlight_pwm_hz; |
| /* Start with a 50% duty cycle. */ |
| write32(base + BLC_PWM_PCH_CTL2, pwm_period << 16 | pwm_period / 2); |
| |
| write32(base + BLC_PWM_PCH_CTL1, |
| !!panel_cfg->backlight_polarity << 29 | BLM_PCH_PWM_ENABLE); |
| } |
| } |
| |
| const struct i915_gpu_controller_info * |
| intel_igd_get_controller_info(const struct device *device) |
| { |
| struct soc_intel_skylake_config *chip = device->chip_info; |
| return &chip->gfx; |
| } |
| |
| /* |
| * Some VGA option roms are used for several chipsets but they only have one PCI ID in their |
| * header. If we encounter such an option rom, we need to do the mapping ourselves. |
| */ |
| u32 map_oprom_vendev(u32 vendev) |
| { |
| u32 new_vendev = vendev; |
| |
| switch (vendev) { |
| case 0x80865916: /* PCI_DEVICE_ID_INTEL_KBL_GT2_SULTM */ |
| case 0x80865917: /* PCI_DEVICE_ID_INTEL_KBL_GT2_SULTMR */ |
| new_vendev = SA_IGD_OPROM_VENDEV; |
| break; |
| } |
| |
| return new_vendev; |
| } |