| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #ifndef _SOC_CHIP_H_ |
| #define _SOC_CHIP_H_ |
| |
| #include <acpi/acpi_device.h> |
| #include <device/i2c_simple.h> |
| #include <drivers/i2c/designware/dw_i2c.h> |
| #include <drivers/intel/gma/gma.h> |
| #include <intelblocks/cfg.h> |
| #include <intelblocks/gspi.h> |
| #include <intelblocks/lpc_lib.h> |
| #include <intelblocks/power_limit.h> |
| #include <stdint.h> |
| #include <soc/gpe.h> |
| #include <soc/gpio.h> |
| #include <soc/irq.h> |
| #include <soc/pci_devs.h> |
| #include <soc/pmc.h> |
| #include <soc/serialio.h> |
| #include <soc/usb.h> |
| #include <soc/vr_config.h> |
| |
| #define MAX_PEG_PORTS 3 |
| |
| enum skylake_i2c_voltage { |
| I2C_VOLTAGE_3V3, |
| I2C_VOLTAGE_1V8 |
| }; |
| |
| struct soc_intel_skylake_config { |
| |
| /* Common struct containing soc config data required by common code */ |
| struct soc_intel_common_config common_soc_config; |
| |
| /* Common struct containing power limits configuration information */ |
| struct soc_power_limits_config power_limits_config; |
| |
| /* IGD panel configuration */ |
| struct i915_gpu_panel_config panel_cfg; |
| |
| /* Gpio group routed to each dword of the GPE0 block. Values are |
| * of the form GPP_[A:G] or GPD. */ |
| uint8_t gpe0_dw0; /* GPE0_31_0 STS/EN */ |
| uint8_t gpe0_dw1; /* GPE0_63_32 STS/EN */ |
| uint8_t gpe0_dw2; /* GPE0_95_64 STS/EN */ |
| |
| /* LPC fixed enables and ranges */ |
| uint16_t lpc_iod; |
| uint16_t lpc_ioe; |
| |
| /* Generic IO decode ranges */ |
| uint32_t gen1_dec; |
| uint32_t gen2_dec; |
| uint32_t gen3_dec; |
| uint32_t gen4_dec; |
| |
| /* Enable S0iX support */ |
| int s0ix_enable; |
| |
| /* Enable DPTF support */ |
| int dptf_enable; |
| |
| /* Deep SX enables */ |
| int deep_s3_enable_ac; |
| int deep_s3_enable_dc; |
| int deep_s5_enable_ac; |
| int deep_s5_enable_dc; |
| |
| /* |
| * Deep Sx Configuration |
| * DSX_EN_WAKE_PIN - Enable WAKE# pin |
| * DSX_EN_LAN_WAKE_PIN - Enable LAN_WAKE# pin |
| * DSX_DIS_AC_PRESENT_PD - Disable pull-down on AC_PRESENT pin |
| */ |
| uint32_t deep_sx_config; |
| |
| /* TCC activation offset */ |
| uint32_t tcc_offset; |
| |
| /* Whether to ignore VT-d support of the SKU */ |
| int ignore_vtd; |
| |
| /* |
| * System Agent dynamic frequency configuration |
| * When enabled memory will be trained at two different frequencies. |
| * 0 = Disabled |
| * 1 = FixedLow |
| * 2 = FixedHigh |
| * 3 = Enabled |
| */ |
| enum { |
| SaGv_Disabled, |
| SaGv_FixedLow, |
| SaGv_FixedHigh, |
| SaGv_Enabled, |
| } SaGv; |
| |
| /* Enable/disable Rank Margin Tool */ |
| u8 Rmt; |
| |
| /* Disable Command TriState */ |
| u8 CmdTriStateDis; |
| |
| /* Lan */ |
| u8 EnableLanLtr; |
| u8 EnableLanK1Off; |
| u8 LanClkReqSupported; |
| u8 LanClkReqNumber; |
| |
| /* SATA related */ |
| enum { |
| SATA_AHCI = 0, |
| SATA_RAID = 1, |
| } SataMode; |
| u8 SataSalpSupport; |
| u8 SataPortsEnable[8]; |
| u8 SataPortsDevSlp[8]; |
| u8 SataPortsSpinUp[8]; |
| u8 SataPortsHotPlug[8]; |
| u8 SataSpeedLimit; |
| |
| /* Audio related */ |
| u8 DspEnable; |
| |
| /* HDA Virtual Channel Type Select */ |
| enum { |
| Vc0, |
| Vc1, |
| } PchHdaVcType; |
| |
| /* |
| * I/O Buffer Ownership: |
| * 0: HD-A Link |
| * 1 Shared, HD-A Link and I2S Port |
| * 3: I2S Ports |
| */ |
| u8 IoBufferOwnership; |
| |
| /* Trace Hub function */ |
| u32 TraceHubMemReg0Size; |
| u32 TraceHubMemReg1Size; |
| |
| /* DCI Enable/Disable */ |
| u8 PchDciEn; |
| |
| /* |
| * PCIe Root Port configuration: |
| * each element of array corresponds to |
| * respective PCIe root port. |
| */ |
| |
| /* PEG Max Link Width */ |
| enum { |
| Peg0_x16, |
| Peg0_x1, |
| Peg0_x2, |
| Peg0_x4, |
| Peg0_x8, |
| } Peg0MaxLinkWidth; |
| |
| enum { |
| Peg1_x8, |
| Peg1_x1, |
| Peg1_x2, |
| Peg1_x4, |
| } Peg1MaxLinkWidth; |
| |
| enum { |
| Peg2_x4, |
| Peg2_x1, |
| Peg2_x2, |
| } Peg2MaxLinkWidth; |
| |
| /* |
| * Enable/Disable Root Port |
| * 0: Disable Root Port |
| * 1: Enable Root Port |
| */ |
| u8 PcieRpEnable[CONFIG_MAX_ROOT_PORTS]; |
| |
| /* |
| * Enable/Disable Clk-req support for Root Port |
| * 0: Disable Clk-Req |
| * 1: Enable Clk-req |
| */ |
| u8 PcieRpClkReqSupport[CONFIG_MAX_ROOT_PORTS]; |
| |
| /* |
| * Clk-req source for Root Port |
| */ |
| u8 PcieRpClkReqNumber[CONFIG_MAX_ROOT_PORTS]; |
| |
| /* |
| * Clk source number for Root Port |
| */ |
| u8 PcieRpClkSrcNumber[CONFIG_MAX_ROOT_PORTS]; |
| |
| /* |
| * Enable/Disable AER (Advanced Error Reporting) for Root Port |
| * 0: Disable AER |
| * 1: Enable AER |
| */ |
| u8 PcieRpAdvancedErrorReporting[CONFIG_MAX_ROOT_PORTS]; |
| |
| /* |
| * Enable/Disable Latency Tolerance Reporting for Root Port |
| * 0: Disable LTR |
| * 1: Enable LTR |
| */ |
| u8 PcieRpLtrEnable[CONFIG_MAX_ROOT_PORTS]; |
| |
| /* Enable/Disable HotPlug support for Root Port */ |
| u8 PcieRpHotPlug[CONFIG_MAX_ROOT_PORTS]; |
| |
| /* PCIE RP Max Payload, Max Payload Size supported */ |
| enum { |
| RpMaxPayload_128, |
| RpMaxPayload_256, |
| } PcieRpMaxPayload[CONFIG_MAX_ROOT_PORTS]; |
| |
| /* PCIE RP ASPM, ASPM support for the root port */ |
| enum { |
| AspmDefault, |
| AspmDisabled, |
| AspmL0s, |
| AspmL1, |
| AspmL0sL1, |
| AspmAutoConfig, |
| } pcie_rp_aspm[CONFIG_MAX_ROOT_PORTS]; |
| |
| /* PCIe RP L1 substate */ |
| enum { |
| L1SS_Default, |
| L1SS_Disabled, |
| L1SS_L1_1, |
| L1SS_L1_2, |
| } pcie_rp_l1substates[CONFIG_MAX_ROOT_PORTS]; |
| |
| /* USB related */ |
| struct usb2_port_config usb2_ports[16]; |
| struct usb3_port_config usb3_ports[10]; |
| u8 SsicPortEnable; |
| |
| /* |
| * SerialIO device mode selection: |
| * |
| * Device index: |
| * PchSerialIoIndexI2C0 |
| * PchSerialIoIndexI2C1 |
| * PchSerialIoIndexI2C2 |
| * PchSerialIoIndexI2C3 |
| * PchSerialIoIndexI2C4 |
| * PchSerialIoIndexI2C5 |
| * PchSerialIoIndexI2C6 |
| * PchSerialIoIndexSpi0 |
| * PchSerialIoIndexSpi1 |
| * PchSerialIoIndexUart0 |
| * PchSerialIoIndexUart1 |
| * PchSerialIoIndexUart2 |
| * |
| * Mode select: |
| * PchSerialIoDisabled |
| * PchSerialIoAcpi |
| * PchSerialIoPci |
| * PchSerialIoAcpiHidden |
| * PchSerialIoLegacyUart |
| */ |
| u8 SerialIoDevMode[PchSerialIoIndexMax]; |
| |
| /* I2C */ |
| /* Bus voltage level, default is 3.3V */ |
| enum skylake_i2c_voltage i2c_voltage[CONFIG_SOC_INTEL_I2C_DEV_MAX]; |
| |
| /* eMMC and SD */ |
| u8 ScsEmmcHs400Enabled; |
| u8 EmmcHs400DllNeed; |
| u8 ScsEmmcHs400RxStrobeDll1; |
| u8 ScsEmmcHs400TxDataDll; |
| |
| enum { |
| Display_iGFX, |
| Display_PEG, |
| Display_PCH_PCIe, |
| Display_Auto, |
| Display_Switchable, |
| } PrimaryDisplay; |
| u8 SkipExtGfxScan; |
| u8 ScanExtGfxForLegacyOpRom; |
| |
| /* |
| * The following fields come from fsp_vpd.h |
| * These are configuration values that are passed to FSP during |
| * SiliconInit. |
| */ |
| u32 LogoPtr; |
| u32 LogoSize; |
| |
| /* GPIO IRQ Route The valid values is 14 or 15*/ |
| u8 GpioIrqSelect; |
| /* SCI IRQ Select The valid values is 9, 10, 11 and 20 21, 22, 23*/ |
| u8 SciIrqSelect; |
| /* TCO IRQ Select The valid values is 9, 10, 11, 20 21, 22, 23*/ |
| u8 TcoIrqSelect; |
| u8 TcoIrqEnable; |
| /* Enable SMI_LOCK bit to prevent writes to the Global SMI Enable bit.*/ |
| u8 LockDownConfigGlobalSmi; |
| /* |
| * Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh |
| * in the upper and and lower 128-byte bank of RTC RAM. |
| */ |
| u8 LockDownConfigRtcLock; |
| |
| /* |
| * Determine if WLAN wake from Sx, corresponds to the |
| * HOST_WLAN_PP_EN bit in the PWRM_CFG3 register. |
| */ |
| u8 PchPmWoWlanEnable; |
| |
| /* |
| * Determine if WLAN wake from DeepSx, corresponds to |
| * the DSX_WLAN_PP_EN bit in the PWRM_CFG3 register. |
| */ |
| u8 PchPmWoWlanDeepSxEnable; |
| |
| /* |
| * Corresponds to the "WOL Enable Override" bit in the General PM |
| * Configuration B (GEN_PMCON_B) register |
| */ |
| u8 WakeConfigWolEnableOverride; |
| /* Determine if enable PCIe to wake from deep Sx*/ |
| u8 WakeConfigPcieWakeFromDeepSx; |
| /* Deep Sx Policy. Values 0: PchDeepSxPolDisable, |
| * 1: PchDpS5BatteryEn, 2: PchDpS5AlwaysEn, 3: PchDpS4S5BatteryEn, |
| * 4: PchDpS4S5AlwaysEn, 5: PchDpS3S4S5BatteryEn, 6: PchDpS3S4S5AlwaysEn |
| */ |
| u8 PmConfigDeepSxPol; |
| |
| enum { |
| SLP_S3_MIN_ASSERT_60US = 0, |
| SLP_S3_MIN_ASSERT_1MS = 1, |
| SLP_S3_MIN_ASSERT_50MS = 2, |
| SLP_S3_MIN_ASSERT_2S = 3, |
| } PmConfigSlpS3MinAssert; |
| |
| enum { |
| SLP_S4_MIN_ASSERT_PCH = 0, |
| SLP_S4_MIN_ASSERT_1S = 1, |
| SLP_S4_MIN_ASSERT_2S = 2, |
| SLP_S4_MIN_ASSERT_3S = 3, |
| SLP_S4_MIN_ASSERT_4S = 4, |
| } PmConfigSlpS4MinAssert; |
| |
| /* When deep Sx enabled: Must be greater than or equal to |
| all other minimum assertion widths. */ |
| enum { |
| SLP_SUS_MIN_ASSERT_0MS = 0, |
| SLP_SUS_MIN_ASSERT_500MS = 1, |
| SLP_SUS_MIN_ASSERT_1S = 2, |
| SLP_SUS_MIN_ASSERT_4S = 3, |
| } PmConfigSlpSusMinAssert; |
| |
| enum { |
| SLP_A_MIN_ASSERT_0MS = 0, |
| SLP_A_MIN_ASSERT_4S = 1, |
| SLP_A_MIN_ASSERT_98MS = 2, |
| SLP_A_MIN_ASSERT_2S = 3, |
| } PmConfigSlpAMinAssert; |
| |
| /* |
| * SLP_X Stretching After SUS Well Power Up. Values 0: Disabled, |
| * 1: Enabled |
| */ |
| u8 PmConfigSlpStrchSusUp; |
| /* |
| * PCH power button override period. |
| * Values: 0x0 - 4s, 0x1 - 6s, 0x2 - 8s, 0x3 - 10s, 0x4 - 12s, 0x5 - 14s |
| */ |
| u8 PmConfigPwrBtnOverridePeriod; |
| |
| /* |
| * PCH Pm Slp S0 Voltage Margining Enable |
| * Indicates platform supports VCCPrim_Core Voltage Margining |
| * in SLP_S0# asserted state. |
| */ |
| u8 PchPmSlpS0VmEnable; |
| |
| enum { |
| RESET_POWER_CYCLE_DEFAULT = 0, |
| RESET_POWER_CYCLE_1S = 1, |
| RESET_POWER_CYCLE_2S = 2, |
| RESET_POWER_CYCLE_3S = 3, |
| RESET_POWER_CYCLE_4S = 4, |
| } PmConfigPwrCycDur; |
| |
| enum serirq_mode serirq_mode; |
| |
| enum { |
| SERIAL_IRQ_FRAME_PULSE_4CLK = 0, |
| SERIAL_IRQ_FRAME_PULSE_6CLK = 1, |
| SERIAL_IRQ_FRAME_PULSE_8CLK = 2, |
| } SerialIrqConfigStartFramePulse; |
| |
| /* |
| * VrConfig Settings for 5 domains |
| * 0 = System Agent, 1 = IA Core, 2 = Ring, |
| * 3 = GT unsliced, 4 = GT sliced |
| */ |
| struct vr_config domain_vr_config[NUM_VR_DOMAINS]; |
| /* |
| * HeciEnabled decides the state of Heci1 at end of boot |
| * Setting to 0 (default) disables Heci1 and hides the device from OS |
| */ |
| u8 HeciEnabled; |
| |
| /* |
| * Enable VR specific mailbox command |
| * 000b - Don't Send any VR command |
| * 001b - VR command specifically for the MPS IMPV8 VR will be sent |
| * 010b - VR specific command sent for PS4 exit issue |
| * 011b - VR specific command sent for both MPS IMPV8 & PS4 exit issue |
| */ |
| u8 SendVrMbxCmd; |
| |
| /* Enable/Disable host reads to PMC XRAM registers */ |
| u8 PchPmPmcReadDisable; |
| |
| /* |
| * Use SD card detect GPIO with default config: |
| * - Edge triggered |
| * - No internal pull |
| * - Active both (high + low) |
| * - Can wake device from D3 |
| * - 100ms debounce timeout |
| * |
| * GpioInt (Edge, ActiveBoth, SharedAndWake, PullNone, 10000, |
| * "\\_SB.PCI0.GPIO", 0, ResourceConsumer) |
| * { sdcard_cd_gpio_default } |
| */ |
| unsigned int sdcard_cd_gpio_default; |
| |
| /* Use custom SD card detect GPIO configuration */ |
| struct acpi_gpio sdcard_cd_gpio; |
| |
| /* Wake Enable Bitmap for USB2 ports */ |
| u16 usb2_wake_enable_bitmap; |
| |
| /* Wake Enable Bitmap for USB3 ports */ |
| u8 usb3_wake_enable_bitmap; |
| |
| /* |
| * Acoustic Noise Mitigation |
| * 0b - Disable |
| * 1b - Enable noise mitigation |
| */ |
| u8 AcousticNoiseMitigation; |
| |
| /* |
| * Disable Fast Package C-state ramping |
| * Need to set AcousticNoiseMitigation = '1' first |
| * 0b - Enabled |
| * 1b - Disabled |
| */ |
| u8 FastPkgCRampDisableIa; |
| u8 FastPkgCRampDisableGt; |
| u8 FastPkgCRampDisableSa; |
| |
| /* |
| * Adjust the VR slew rates |
| * Need to set AcousticNoiseMitigation = '1' first |
| * 000b - Fast/2 |
| * 001b - Fast/4 |
| * 010b - Fast/8 |
| * 011b - Fast/16 |
| */ |
| u8 SlowSlewRateForIa; |
| u8 SlowSlewRateForGt; |
| u8 SlowSlewRateForSa; |
| |
| /* Enable/Disable EIST |
| * 1b - Enabled |
| * 0b - Disabled |
| */ |
| u8 eist_enable; |
| |
| /* |
| * Activates VR mailbox command for Intersil VR C-state issues. |
| * 0 - no mailbox command sent. |
| * 1 - VR mailbox command sent for IA/GT rails only. |
| * 2 - VR mailbox command sent for IA/GT/SA rails. |
| */ |
| u8 IslVrCmd; |
| |
| /* Enable/Disable Sata test mode */ |
| u8 SataTestMode; |
| |
| /* i915 struct for GMA backlight control */ |
| struct i915_gpu_controller_info gfx; |
| }; |
| |
| typedef struct soc_intel_skylake_config config_t; |
| |
| #endif |