| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| /* the problem: we have 82801dbm support in fb1, and 82801er in fb2. |
| * fb1 code is what we want, fb2 structure is needed however. |
| * so we need to get fb1 code for 82801dbm into fb2 structure. |
| */ |
| /* What I did: took the 80801er stuff from fb2, verify it against the |
| * db stuff in fb1, and made sure it was right. |
| */ |
| |
| #ifndef I82801DX_H |
| #define I82801DX_H |
| |
| #include <acpi/acpi.h> |
| |
| #if !defined(__ASSEMBLER__) |
| |
| #include <device/device.h> |
| |
| void i82801dx_enable(struct device *dev); |
| void i82801dx_early_init(void); |
| void aseg_smm_lock(void); |
| |
| #endif |
| |
| #define DEBUG_PERIODIC_SMIS 0 |
| |
| #define MAINBOARD_POWER_OFF 0 |
| #define MAINBOARD_POWER_ON 1 |
| #define MAINBOARD_POWER_KEEP 2 |
| |
| /* |
| * 000 = Non-combined. P0 is primary master. P1 is secondary master. |
| * 001 = Non-combined. P0 is secondary master. P1 is primary master. |
| * 100 = Combined. P0 is primary master. P1 is primary slave. IDE is secondary; |
| * Primary IDE channel disabled. |
| * 101 = Combined. P0 is primary slave. P1 is primary master. IDE is secondary. |
| * 110 = Combined. IDE is primary. P0 is secondary master. P1 is secondary |
| * slave; Secondary IDE channel disabled. |
| * 111 = Combined. IDE is primary. P0 is secondary slave. P1 is secondary master. |
| */ |
| /* PCI Configuration Space (D31:F1) */ |
| #define IDE_TIM_PRI 0x40 /* IDE timings, primary */ |
| #define IDE_TIM_SEC 0x42 /* IDE timings, secondary */ |
| |
| /* IDE_TIM bits */ |
| #define IDE_DECODE_ENABLE (1 << 15) |
| |
| #define PCI_DMA_CFG 0x90 |
| #define SERIRQ_CNTL 0x64 |
| #define GEN_CNTL 0xd0 |
| #define GEN_STS 0xd4 |
| #define RTC_CONF 0xd8 |
| #define GEN_PMCON_3 0xa4 |
| |
| #define PCICMD 0x04 |
| #define PMBASE 0x40 |
| #define PMBASE_ADDR 0x0400 |
| #define DEFAULT_PMBASE PMBASE_ADDR |
| #define ACPI_CNTL 0x44 |
| #define ACPI_EN (1 << 4) |
| #define BIOS_CNTL 0x4E |
| #define GPIO_BASE 0x58 |
| #define GPIO_CNTL 0x5C |
| #define GPIOBASE_ADDR 0x0500 |
| #define PIRQA_ROUT 0x60 |
| #define PIRQB_ROUT 0x61 |
| #define PIRQC_ROUT 0x62 |
| #define PIRQD_ROUT 0x63 |
| #define PIRQE_ROUT 0x68 |
| #define PIRQF_ROUT 0x69 |
| #define PIRQG_ROUT 0x6A |
| #define PIRQH_ROUT 0x6B |
| #define COM_DEC 0xE0 |
| #define LPC_EN 0xE6 |
| #define FUNC_DIS 0xF2 |
| |
| /* 1e f0 244e */ |
| |
| #define CMD 0x04 |
| #define SBUS_NUM 0x19 |
| #define SUB_BUS_NUM 0x1A |
| #define SMLT 0x1B |
| #define IOBASE 0x1C |
| #define IOLIM 0x1D |
| #define MEMBASE 0x20 |
| #define MEMLIM 0x22 |
| #define CNF 0x50 |
| #define MTT 0x70 |
| #define PCI_MAST_STS 0x82 |
| |
| #define RTC_FAILED (1 <<2) |
| |
| #define PM1_STS 0x00 |
| #define WAK_STS (1 << 15) |
| #define PCIEXPWAK_STS (1 << 14) |
| #define PRBTNOR_STS (1 << 11) |
| #define RTC_STS (1 << 10) |
| #define PWRBTN_STS (1 << 8) |
| #define GBL_STS (1 << 5) |
| #define BM_STS (1 << 4) |
| #define TMROF_STS (1 << 0) |
| #define PM1_EN 0x02 |
| #define PCIEXPWAK_DIS (1 << 14) |
| #define RTC_EN (1 << 10) |
| #define PWRBTN_EN (1 << 8) |
| #define GBL_EN (1 << 5) |
| #define TMROF_EN (1 << 0) |
| #define PM1_CNT 0x04 |
| #define GBL_RLS (1 << 2) |
| #define BM_RLD (1 << 1) |
| #define SCI_EN (1 << 0) |
| #define PM1_TMR 0x08 |
| #define PROC_CNT 0x10 |
| #define LV2 0x14 |
| #define LV3 0x15 |
| #define LV4 0x16 |
| #define PM2_CNT 0x20 // mobile only |
| #define GPE0_STS 0x28 |
| #define PME_B0_STS (1 << 13) |
| #define USB3_STS (1 << 12) |
| #define PME_STS (1 << 11) |
| #define BATLOW_STS (1 << 10) |
| #define GST_STS (1 << 9) |
| #define RI_STS (1 << 8) |
| #define SMB_WAK_STS (1 << 7) |
| #define TCOSCI_STS (1 << 6) |
| #define AC97_STS (1 << 5) |
| #define USB2_STS (1 << 4) |
| #define USB1_STS (1 << 3) |
| #define SWGPE_STS (1 << 2) |
| #define HOT_PLUG_STS (1 << 1) |
| #define THRM_STS (1 << 0) |
| #define GPE0_EN 0x2c |
| #define PME_B0_EN (1 << 13) |
| #define PME_EN (1 << 11) |
| #define SMI_EN 0x30 |
| #define EL_SMI_EN (1 << 25) // Intel Quick Resume Technology |
| #define INTEL_USB2_EN (1 << 18) // Intel-Specific USB2 SMI logic |
| #define LEGACY_USB2_EN (1 << 17) // Legacy USB2 SMI logic |
| #define PERIODIC_EN (1 << 14) // SMI on PERIODIC_STS in SMI_STS |
| #define TCO_EN (1 << 13) // Enable TCO Logic (BIOSWE et al) |
| #define MCSMI_EN (1 << 11) // Trap microcontroller range access |
| #define BIOS_RLS (1 << 7) // asserts SCI on bit set |
| #define SWSMI_TMR_EN (1 << 6) // start software smi timer on bit set |
| #define APMC_EN (1 << 5) // Writes to APM_CNT cause SMI# |
| #define SLP_SMI_EN (1 << 4) // Write to SLP_EN in PM1_CNT asserts SMI# |
| #define LEGACY_USB_EN (1 << 3) // Legacy USB circuit SMI logic |
| #define BIOS_EN (1 << 2) // Assert SMI# on setting GBL_RLS bit |
| #define EOS (1 << 1) // End of SMI (deassert SMI#) |
| #define GBL_SMI_EN (1 << 0) // SMI# generation at all? |
| #define SMI_STS 0x34 |
| #define ALT_GP_SMI_EN 0x38 |
| #define ALT_GP_SMI_STS 0x3a |
| #define GPE_CNTL 0x42 |
| #define DEVACT_STS 0x44 |
| #define SS_CNT 0x50 |
| #define C3_RES 0x54 |
| |
| #define TCOBASE 0x60 /* TCO Base Address Register */ |
| #define TCO1_CNT 0x08 /* TCO1 Control Register */ |
| |
| #define GEN_PMCON_1 0xa0 |
| #define GEN_PMCON_2 0xa2 |
| #define GEN_PMCON_3 0xa4 |
| |
| /* GEN_PMCON_3 bits */ |
| #define RTC_BATTERY_DEAD (1 << 2) |
| #define RTC_POWER_FAILED (1 << 1) |
| #define SLEEP_AFTER_POWER_FAIL (1 << 0) |
| |
| #endif /* I82801DX_H */ |