| chip northbridge/intel/sandybridge |
| # IGD Displays |
| register "gfx" = "GMA_STATIC_DISPLAYS(0)" |
| |
| # Enable DisplayPort Hotplug with 6ms pulse |
| register "gpu_dp_d_hotplug" = "0x06" |
| |
| |
| # Enable Panel as LVDS and configure power delays |
| register "gpu_panel_port_select" = "PANEL_PORT_LVDS" |
| register "gpu_panel_power_cycle_delay" = "6" # T7: 500ms |
| register "gpu_panel_power_up_delay" = "100" # T1+T2: 10ms |
| register "gpu_panel_power_down_delay" = "100" # T5+T6: 10ms |
| register "gpu_panel_power_backlight_on_delay" = "2100" # T3: 210ms |
| register "gpu_panel_power_backlight_off_delay" = "2100" # T4: 210ms |
| |
| # Set backlight PWM values |
| register "gpu_cpu_backlight" = "0x000001e8" |
| register "gpu_pch_backlight" = "0x03d00000" |
| |
| register "max_mem_clock_mhz" = "666" # DDR3-1333 |
| |
| device cpu_cluster 0 on |
| chip cpu/intel/model_206ax |
| # Magic APIC ID to locate this chip |
| device lapic 0 on end |
| device lapic 0xacac off end |
| |
| register "acpi_c1" = "1" # ACPI(C1) = MWAIT(C1) |
| register "acpi_c2" = "3" # ACPI(C2) = MWAIT(C3) |
| register "acpi_c3" = "5" # ACPI(C3) = MWAIT(C7) |
| end |
| end |
| |
| device domain 0 on |
| device pci 00.0 on end # host bridge |
| device pci 01.0 off end # PCIe Bridge for discrete graphics |
| device pci 02.0 on end # vga controller |
| |
| chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH |
| # GPI routing |
| # 0 No effect (default) |
| # 1 SMI# (if corresponding ALT_GPI_SMI_EN bit is also set) |
| # 2 SCI (if corresponding GPIO_EN bit is also set) |
| register "alt_gp_smi_en" = "0x0000" |
| #register "gpi1_routing" = "1" #SMI from EC |
| register "gpi13_routing" = "2" #SCI from EC |
| |
| # Enable SATA ports 0 & 1 |
| register "sata_port_map" = "0x3" |
| # Set max SATA speed to 3.0 Gb/s |
| register "sata_interface_speed_support" = "0x2" |
| |
| # Enable EC Port 0x68/0x6C |
| register "gen1_dec" = "0x00040069" |
| |
| # EC range is 0x380-0387 |
| register "gen2_dec" = "0x00040381" |
| |
| # Enable zero-based linear PCIe root port functions |
| register "pcie_port_coalesce" = "true" |
| |
| device pci 14.0 on end # USB 3.0 Controller |
| device pci 16.0 on end # Management Engine Interface 1 |
| device pci 16.1 off end # Management Engine Interface 2 |
| device pci 16.2 off end # Management Engine IDE-R |
| device pci 16.3 off end # Management Engine KT |
| device pci 19.0 off end # Intel Gigabit Ethernet |
| device pci 1a.0 on end # USB2 EHCI #2 |
| device pci 1b.0 on end # High Definition Audio |
| device pci 1c.0 on end # PCIe Port #1 (mini PCIe Slot - WLAN & Serial debug) |
| device pci 1c.1 on end # PCIe Port #2 (ETH0) |
| device pci 1c.2 on end # PCIe Port #3 (Card Reader) |
| #force ASPM for PCIe bridge to Card Reader |
| register "pcie_aspm[2]" = "0x3" |
| device pci 1c.3 off end # PCIe Port #4 |
| device pci 1c.4 off end # PCIe Port #5 |
| device pci 1c.5 off end # PCIe Port #6 |
| device pci 1c.6 off end # PCIe Port #7 |
| device pci 1c.7 off end # PCIe Port #8 |
| device pci 1d.0 on end # USB2 EHCI #1 |
| device pci 1e.0 off end # PCI bridge |
| device pci 1f.0 on #LPC bridge |
| chip drivers/pc80/tpm |
| device pnp 0c31.0 on end |
| end |
| chip ec/quanta/ene_kb3940q |
| # 60/64 KBC |
| device pnp ff.1 on # dummy address |
| end |
| end |
| end # LPC bridge |
| device pci 1f.2 on end # SATA Controller 1 |
| device pci 1f.3 on end # SMBus |
| device pci 1f.5 off end # SATA Controller 2 |
| device pci 1f.6 on end # Thermal |
| end |
| end |
| end |