| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2012 secunet Security Networks AG |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; version 2 of |
| * the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| // __PRE_RAM__ means: use "unsigned" for device, not a struct. |
| |
| #include <stdint.h> |
| #include <string.h> |
| #include <arch/io.h> |
| #include <arch/acpi.h> |
| #include <cpu/x86/lapic.h> |
| #include <cpu/x86/tsc.h> |
| #include <cpu/intel/romstage.h> |
| #include <cbmem.h> |
| #include <romstage_handoff.h> |
| #include <console/console.h> |
| #include <southbridge/intel/i82801ix/i82801ix.h> |
| #include <southbridge/intel/common/gpio.h> |
| #include <northbridge/intel/gm45/gm45.h> |
| #include <drivers/lenovo/hybrid_graphics/hybrid_graphics.h> |
| #include "dock.h" |
| |
| #define LPC_DEV PCI_DEV(0, 0x1f, 0) |
| #define MCH_DEV PCI_DEV(0, 0, 0) |
| |
| static void hybrid_graphics_init(sysinfo_t *sysinfo) |
| { |
| bool peg, igd; |
| |
| early_hybrid_graphics(&igd, &peg); |
| |
| sysinfo->enable_igd = igd; |
| sysinfo->enable_peg = peg; |
| } |
| |
| static void early_lpc_setup(void) |
| { |
| /* Set up SuperIO LPC forwards */ |
| |
| /* Configure serial IRQs.*/ |
| pci_write_config8(LPC_DEV, D31F0_SERIRQ_CNTL, 0xd0); |
| /* Map COMa on 0x3f8, COMb on 0x2f8. */ |
| pci_write_config16(LPC_DEV, D31F0_LPC_IODEC, 0x0010); |
| pci_write_config16(LPC_DEV, D31F0_LPC_EN, 0x3f0f); |
| pci_write_config32(LPC_DEV, D31F0_GEN1_DEC, 0x7c1601); |
| pci_write_config32(LPC_DEV, D31F0_GEN2_DEC, 0xc15e1); |
| pci_write_config32(LPC_DEV, D31F0_GEN3_DEC, 0x1c1681); |
| } |
| |
| void mainboard_romstage_entry(unsigned long bist) |
| { |
| sysinfo_t sysinfo; |
| int s3resume = 0; |
| int cbmem_initted; |
| int err; |
| u16 reg16; |
| |
| /* basic northbridge setup, including MMCONF BAR */ |
| gm45_early_init(); |
| |
| if (bist == 0) |
| enable_lapic(); |
| |
| /* First, run everything needed for console output. */ |
| i82801ix_early_init(); |
| early_lpc_setup(); |
| |
| /* Minimal setup to detect dock */ |
| err = pc87382_early(); |
| if (err == 0) |
| dock_connect(); |
| |
| console_init(); |
| printk(BIOS_DEBUG, "running main(bist = %lu)\n", bist); |
| |
| /* Print dock info */ |
| if (err) |
| printk(BIOS_ERR, "DOCK: Failed to init pc87382\n"); |
| else |
| dock_info(); |
| |
| reg16 = pci_read_config16(LPC_DEV, D31F0_GEN_PMCON_3); |
| pci_write_config16(LPC_DEV, D31F0_GEN_PMCON_3, reg16); |
| if ((MCHBAR16(SSKPD_MCHBAR) == 0xCAFE) && !(reg16 & (1 << 9))) { |
| printk(BIOS_DEBUG, "soft reset detected, rebooting properly\n"); |
| gm45_early_reset(); |
| } |
| |
| setup_pch_gpios(&mainboard_gpio_map); |
| |
| /* ASPM related setting, set early by original BIOS. */ |
| DMIBAR16(0x204) &= ~(3 << 10); |
| |
| /* Check for S3 resume. */ |
| const u32 pm1_cnt = inl(DEFAULT_PMBASE + 0x04); |
| if (((pm1_cnt >> 10) & 7) == 5) { |
| if (acpi_s3_resume_allowed()) { |
| printk(BIOS_DEBUG, "Resume from S3 detected.\n"); |
| s3resume = 1; |
| /* Clear SLP_TYPE. This will break stage2 but |
| * we care for that when we get there. |
| */ |
| outl(pm1_cnt & ~(7 << 10), DEFAULT_PMBASE + 0x04); |
| } else { |
| printk(BIOS_DEBUG, "Resume from S3 detected, but disabled.\n"); |
| } |
| } |
| |
| /* RAM initialization */ |
| enter_raminit_or_reset(); |
| memset(&sysinfo, 0, sizeof(sysinfo)); |
| sysinfo.spd_map[0] = 0x50; |
| sysinfo.spd_map[2] = 0x51; |
| get_gmch_info(&sysinfo); |
| |
| /* Configure graphic GPIOs. |
| * Make sure there's a little delay between |
| * setup_pch_gpios() and this call ! */ |
| hybrid_graphics_init(&sysinfo); |
| |
| raminit(&sysinfo, s3resume); |
| |
| const u32 deven = pci_read_config32(MCH_DEV, D0F0_DEVEN); |
| /* Disable D4F0 (unknown signal controller). */ |
| pci_write_config32(MCH_DEV, D0F0_DEVEN, deven & ~0x4000); |
| |
| init_pm(&sysinfo, 0); |
| |
| i82801ix_dmi_setup(); |
| gm45_late_init(sysinfo.stepping); |
| i82801ix_dmi_poll_vc1(); |
| |
| MCHBAR16(SSKPD_MCHBAR) = 0xCAFE; |
| /* Enable ethernet. */ |
| RCBA32(0x3414) &= ~0x20; |
| |
| RCBA32(0x0238) = 0x00543210; |
| RCBA32(0x0240) = 0x009c0b02; |
| RCBA32(0x0244) = 0x00a20b1a; |
| RCBA32(0x0248) = 0x005402cb; |
| RCBA32(0x0254) = 0x00470966; |
| RCBA32(0x0258) = 0x00470473; |
| RCBA32(0x0260) = 0x00e90825; |
| RCBA32(0x0278) = 0x00bc0efb; |
| RCBA32(0x027c) = 0x00c00f0b; |
| RCBA32(0x0280) = 0x00670000; |
| RCBA32(0x0284) = 0x006d0000; |
| RCBA32(0x0288) = 0x00600b4e; |
| RCBA32(0x1e10) = 0x00020800; |
| RCBA32(0x1e18) = 0x36ea00a0; |
| RCBA32(0x1e80) = 0x000c0801; |
| RCBA32(0x1e84) = 0x000200f0; |
| RCBA32(0x2028) = 0x04c8f95e; |
| RCBA32(0x202c) = 0x055c095e; |
| RCBA32(0x204c) = 0x001ffc00; |
| RCBA32(0x2050) = 0x00100fff; |
| RCBA32(0x2090) = 0x37000000; |
| RCBA32(0x20b0) = 0x0c000000; |
| RCBA32(0x20d0) = 0x09000000; |
| RCBA32(0x20f0) = 0x05000000; |
| RCBA32(0x3400) = 0x0000001c; |
| RCBA32(0x3410) = 0x00100461; |
| RCBA32(0x3414) = 0x00000000; |
| RCBA32(0x341c) = 0xbf4f001f; |
| RCBA32(0x3420) = 0x00000000; |
| RCBA32(0x3430) = 0x00000001; |
| |
| init_iommu(); |
| |
| /* FIXME: make a proper SMBUS mux support. */ |
| outl(inl(DEFAULT_GPIOBASE + 0x38) & ~0x400, DEFAULT_GPIOBASE + 0x38); |
| |
| cbmem_initted = !cbmem_recovery(s3resume); |
| |
| romstage_handoff_init(cbmem_initted && s3resume); |
| |
| printk(BIOS_SPEW, "exit main()\n"); |
| } |