| fw_config |
| field MB_SD 0 1 |
| option SD_ABSENT 0 |
| option SD_GL9750 1 |
| end |
| field KB_BL 2 2 |
| option KB_BL_ABSENT 0 |
| option KB_BL_PRESENT 1 |
| end |
| field AUDIO 3 5 |
| option AUDIO_UNKNOWN 0 |
| option MAX98360_CS42L42 1 |
| end |
| field DB_LTE 6 7 |
| option LTE_ABSENT 0 |
| option LTE_USB 1 |
| end |
| end |
| |
| chip soc/intel/alderlake |
| register "sagv" = "SaGv_Enabled" |
| register "max_dram_speed_mts" = "4800" |
| register "cnvi_bt_audio_offload" = "1" |
| # +-----------+-------+-------+---------+-------------+----------+ |
| # | Setting | AC LL | DC LL | ICC MAX | TDC Current | TDC Time | |
| # | |(mOhms)|(mOhms)| (A) | (A) | (msec) | |
| # +-----------+-------+-------+---------+-------------+----------+ |
| # | IA | 2.8 | 2.8 | 80 | 43 | 28000 | |
| # +-----------+-------+-------+---------+-------------+----------+ |
| # | GT | 3.2 | 3.2 | 40 | 23 | 28000 | |
| # +-----------+-------+-------+---------+-------------+----------+ |
| register "domain_vr_config[VR_DOMAIN_IA]" = "{ |
| .vr_config_enable = 1, |
| .ac_loadline = 280, |
| .dc_loadline = 280, |
| .icc_max = VR_CFG_AMP(80), |
| .tdc_timewindow = 28000, |
| .tdc_currentlimit = VR_CFG_TDC_AMP(43), |
| }" |
| |
| register "domain_vr_config[VR_DOMAIN_GT]" = "{ |
| .vr_config_enable = 1, |
| .ac_loadline = 320, |
| .dc_loadline = 320, |
| .icc_max = VR_CFG_AMP(40), |
| .tdc_timewindow = 28000, |
| .tdc_currentlimit = VR_CFG_TDC_AMP(23), |
| }" |
| |
| # Acoustic settings |
| register "acoustic_noise_mitigation" = "1" |
| register "slow_slew_rate[VR_DOMAIN_IA]" = "SLEW_FAST_4" |
| register "slow_slew_rate[VR_DOMAIN_GT]" = "SLEW_FAST_4" |
| register "fast_pkg_c_ramp_disable[VR_DOMAIN_IA]" = "1" |
| register "fast_pkg_c_ramp_disable[VR_DOMAIN_GT]" = "1" |
| |
| # As per Intel Advisory doc#723158, the change is required to prevent possible |
| # display flickering issue. |
| register "usb2_phy_sus_pg_disable" = "1" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI1 | Fingerprint MCU | |
| #| I2C0 | Audio | |
| #| I2C1 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C2 | | |
| #| I2C3 | Touchscreen | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[1] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 600, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 650, |
| .fall_time_ns = 400, |
| .data_hold_time_ns = 50, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| }" |
| |
| register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable USB2_C1 |
| register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Disable USB2_C4 |
| register "usb2_ports[6]" = "USB2_PORT_EMPTY" # Disable USB2_C6 |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Type-A MLB Port |
| register "usb2_ports[8]" = "USB2_PORT_EMPTY" # Disable USB2_C8 |
| register "usb3_ports[0]" = "USB3_PORT_EMPTY" |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A MLB port |
| register "tcss_ports[1]" = "TCSS_PORT_EMPTY" |
| register "tcc_offset" = "1" # TCC of 99C |
| |
| device domain 0 on |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""SOC"" |
| register "options.tsr[1].desc" = ""DRAM"" |
| register "options.tsr[2].desc" = ""Charger"" |
| register "options.tsr[3].desc" = ""Ambient"" |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 90, 5000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 90, 5000), |
| [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 90, 5000), |
| [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 90, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), |
| [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 85, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 3000, |
| .max_power = 15000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200, |
| }, |
| .pl2 = { |
| .min_power = 55000, |
| .max_power = 55000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000, |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| device generic 0 alias dptf_policy on end |
| end |
| end |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp3 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B4)" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D11)" |
| register "srcclk_pin" = "1" |
| register "reset_delay_ms" = "50" |
| register "enable_delay_ms" = "20" |
| device generic 0 alias emmc_rtd3 on end |
| end |
| # Enable PCIe-to-eMMC bridge PCIE 3 using clk 1 |
| register "pch_pcie_rp[PCH_RP(3)]" = "{ |
| .clk_src = 1, |
| .clk_req = 1, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| end #PCIE3 BH799BB |
| device ref pcie_rp9 off end |
| device ref tcss_dma0 on |
| chip drivers/intel/usb4/retimer |
| register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| use tcss_usb3_port1 as dfp[0].typec_port |
| device generic 0 on end |
| end |
| end |
| device ref tcss_dma1 on |
| chip drivers/intel/usb4/retimer |
| register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| use tcss_usb3_port3 as dfp[0].typec_port |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp6 off end #PCIE6 WWAN |
| device ref pcie_rp8 on |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" |
| register "srcclk_pin" = "3" |
| device generic 0 on end |
| end |
| end #PCIE8 SD card |
| device ref pcie4_0 on |
| # Enable CPU PCIE RP 1 using CLK 0 |
| register "cpu_pcie_rp[CPU_RP(1)]" = "{ |
| .clk_req = 0, |
| .clk_src = 0, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| end |
| device ref i2c0 on |
| chip drivers/i2c/cs42l42 |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_A23_IRQ)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B15)" |
| register "ts_inv" = "true" |
| register "ts_dbnc_rise" = "RISE_DEB_1000_MS" |
| register "ts_dbnc_fall" = "FALL_DEB_0_MS" |
| register "btn_det_init_dbnce" = "100" |
| register "btn_det_event_dbnce" = "10" |
| register "bias_lvls[0]" = "15" |
| register "bias_lvls[1]" = "8" |
| register "bias_lvls[2]" = "4" |
| register "bias_lvls[3]" = "1" |
| register "hs_bias_ramp_rate" = "HSBIAS_RAMP_SLOW" |
| register "hs_bias_sense_disable" = "true" |
| device i2c 48 on end |
| end |
| end #I2C0 |
| device ref i2c1 on |
| chip drivers/i2c/tpm |
| register "hid" = ""GOOG0005"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" |
| device i2c 50 on end |
| end |
| end |
| device ref i2c3 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN900C"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "150" |
| register "generic.reset_off_delay_ms" = "1" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "6" |
| register "generic.stop_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_off_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x16 on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "wake" = "GPE0_DW2_14" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GXTP7863"" |
| register "generic.desc" = ""Goodix Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 2c on end |
| end |
| end |
| device ref hda on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98360A"" |
| register "sdmode_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "sdmode_delay" = "5" |
| device generic 0 on end |
| end |
| end |
| device ref gspi1 on |
| chip drivers/spi/acpi |
| register "name" = ""CRFP"" |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "uid" = "1" |
| register "compat_string" = ""google,cros-ec-spi"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" |
| register "wake" = "GPE0_DW2_15" |
| register "has_power_resource" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D1)" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D2)" |
| register "enable_delay_ms" = "3" |
| device spi 0 on end |
| end # FPMCU |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port3 as usb2_port |
| use tcss_usb3_port3 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C2 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port3 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C2 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb2_port8 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, LEFT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb3_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb3_port4 on end |
| end |
| end |
| end |
| end |
| end |
| end |