| chip northbridge/intel/sandybridge |
| # IGD Displays |
| register "gfx" = "GMA_STATIC_DISPLAYS(0)" |
| |
| register "spd_addresses" = "{0x50, 0, 0x52, 0}" |
| register "max_mem_clock_mhz" = "800" |
| register "ec_present" = "1" |
| |
| register "usb3.hs_port_switch_mask" = "0xf" |
| register "usb3.mode" = "3" |
| register "usb3.preboot_support" = "1" |
| register "usb3.xhci_streams" = "1" |
| register "usb_port_config" = "{ |
| { 1, 0, 0x0040 }, |
| { 1, 0, 0x0040 }, |
| { 1, 0, 0x0040 }, |
| { 1, 0, 0x0040 }, |
| { 1, 0, 0x0040 }, |
| { 1, 0, 0x0040 }, |
| { 1, 0, 0x0040 }, |
| { 1, 0, 0x0040 }, |
| { 1, 4, 0x0040 }, |
| { 1, 4, 0x0040 }, |
| { 1, 4, 0x0040 }, |
| { 1, 4, 0x0040 }, |
| { 1, 4, 0x0040 }, |
| { 1, 4, 0x0040 }, }" |
| |
| chip cpu/intel/model_206ax |
| device cpu_cluster 0 on end |
| |
| register "acpi_c2" = "CPU_ACPI_C6" |
| register "acpi_c3" = "CPU_ACPI_DISABLED" |
| end |
| |
| device domain 0 on |
| device ref host_bridge on end # host bridge |
| device ref peg10 on end # PCIe Bridge x16 |
| device ref igd on end # vga controller |
| |
| chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH |
| # Enable all SATA ports 0-5 |
| register "sata_port_map" = "0x3f" |
| # Set max SATA speed to 6.0 Gb/s (should be the default, anyway) |
| register "sata_interface_speed_support" = "0x3" |
| |
| # TODO: Enable generic LPC decodes... |
| register "gen1_dec" = "0x001c02e1" |
| #register "gen2_dec" = "0x00000000" |
| #register "gen3_dec" = "0x00000000" |
| #register "gen4_dec" = "0x00000000" |
| |
| # Disable root port coalescing |
| register "pcie_port_coalesce" = "false" |
| |
| register "xhci_switchable_ports" = "0x0f" |
| register "superspeed_capable_ports" = "0x0f" |
| |
| device ref xhci on end # USB 3.0 Controller |
| device ref mei1 on end # Management Engine Interface 1 |
| device ref mei2 off end # Management Engine Interface 2 |
| device ref me_ide_r off end # Management Engine IDE-R |
| device ref me_kt off end # Management Engine KT |
| device ref gbe on end # Intel Gigabit Ethernet |
| device ref ehci2 on end # USB2 EHCI #2 |
| device ref hda on end # High Definition Audio |
| |
| # Disabling 1c.0 might break IRQ settings as it enables port coalescing |
| # There are two mini PCIe x1 sockets, so one PCIe port is unrouted |
| device ref pcie_rp1 on end # PCIe Port #1 mini PCIe x1? |
| device ref pcie_rp2 on end # PCIe Port #2 mini PCIe x1? |
| device ref pcie_rp3 on end # PCIe Port #3 second Ethernet NIC |
| device ref pcie_rp4 on end # PCIe Port #4 third Ethernet NIC |
| device ref pcie_rp5 on end # PCIe Port #5 first Ethernet PHY |
| device ref pcie_rp6 on end # PCIe Port #6 FireWire |
| device ref pcie_rp7 on end # PCIe Port #7 PCIe x1 |
| device ref pcie_rp8 on end # PCIe Port #8 mini PCIe x1? |
| |
| device ref ehci1 on end # USB2 EHCI #1 |
| device ref pci_bridge off end # PCI bridge |
| device ref lpc on #LPC bridge |
| chip superio/winbond/w83627dhg |
| device pnp 2e.0 off # Floppy |
| end |
| device pnp 2e.1 off # Parallel Port |
| end |
| device pnp 2e.2 on # Com1 |
| io 0x60 = 0x3f8 |
| irq 0x70 = 4 |
| end |
| device pnp 2e.3 on # Com2 |
| io 0x60 = 0x2f8 |
| irq 0x70 = 3 |
| end |
| device pnp 2e.5 off # Keyboard |
| end |
| device pnp 2e.6 off # SPI |
| end |
| device pnp 2e.307 off # GPIO 1 |
| end |
| device pnp 2e.8 off # WDTO#, PLED |
| end |
| device pnp 2e.009 on # GPIO2 -- original firmware sets this on |
| end |
| device pnp 2e.109 on # GPIO3 -- original firmware sets this on |
| end |
| device pnp 2e.209 off # GPIO4 |
| end |
| device pnp 2e.309 off # GPIO5 |
| end |
| device pnp 2e.a off # ACPI |
| end |
| device pnp 2e.b off # HWM |
| end |
| device pnp 2e.c off # PECI, SST |
| end |
| end #superio/winbond/w83627dhg |
| chip ec/kontron/it8516e |
| # Set CPU Fan to 50°C, System Fan to 75% |
| register "default_fan_mode" = "{ IT8516E_MODE_THERMAL, IT8516E_MODE_PWM }" |
| register "default_fan_target" = "{ 50, 75 }" |
| |
| # TODO: Check status when Linux runs |
| device pnp 20e.1 on # Com3 |
| io 0x60 = 0x03e8 |
| irq 0x70 = 4 |
| end |
| device pnp 20e.2 on # Com4 |
| io 0x60 = 0x02e8 |
| irq 0x70 = 3 |
| end |
| device pnp 20e.4 off # System Wakeup |
| end |
| device pnp 20e.5 on # Mouse |
| irq 0x70 = 12 |
| end |
| device pnp 20e.6 on # Keyboard |
| io 0x60 = 0x0060 |
| io 0x62 = 0x0064 |
| irq 0x70 = 1 |
| end |
| device pnp 20e.f off # Shared Memory |
| end |
| device pnp 20e.10 off # BRAM / RTC |
| end |
| device pnp 20e.11 on # PM channel 1 |
| io 0x60 = 0x0062 |
| io 0x62 = 0x0066 |
| irq 0x70 = 0 |
| end |
| device pnp 20e.12 on # PM channel 2 |
| io 0x60 = 0x020c |
| io 0x62 = 0x020d |
| irq 0x70 = 0 |
| end |
| device pnp 20e.17 off # PM channel 3 |
| end |
| end #ec/kontron/it8516e |
| # TODO: TPM on 4e |
| end # LPC bridge |
| device ref sata1 on end # SATA Controller 1 |
| device ref smbus on end # SMBus |
| device ref sata2 off end # SATA Controller 2 |
| device ref thermal off end # Thermal |
| end |
| end |
| end |