| fw_config |
| field DB_USB 0 1 |
| option DB_NONE 0 |
| option DB_1C_1A 1 |
| option DB_1C_LTE 2 |
| end |
| field WFC 2 |
| option WFC_MIPI_OV8856 0 |
| option WFC_ABSENT 1 |
| end |
| field STYLUS 3 |
| option STYLUS_PRESENT 0 |
| option STYLUS_ABSENT 1 |
| end |
| end |
| |
| chip soc/intel/alderlake |
| # GPE configuration |
| register "pmc_gpe0_dw1" = "GPP_C" |
| |
| # Enable MIPI DSI on DDI port A |
| register "ddi_portA_config" = "2" # MIPI DSI |
| |
| register "sagv" = "SaGv_Enabled" |
| |
| # SOC Aux orientation override: |
| # This is a bitfield that corresponds to up to 4 TCSS ports. |
| # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2. |
| # TcssAuxOri = 0101b |
| # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports |
| # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the |
| # motherboard to USBC connector |
| register "tcss_aux_ori" = "5" |
| |
| register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" |
| register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" |
| |
| register "usb2_ports[0]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .pre_emp_bias = USB2_BIAS_28P15MV, |
| .tx_bias = USB2_BIAS_0MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bit = USB2_FULL_BIT_PRE_EMP, |
| .type_c = 1, |
| }" # USB2_C0 |
| register "usb2_ports[1]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .pre_emp_bias = USB2_BIAS_28P15MV, |
| .tx_bias = USB2_BIAS_11P25MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bit = USB2_FULL_BIT_PRE_EMP, |
| .type_c = 1, |
| }" # USB2_C1 |
| register "usb2_ports[3]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .pre_emp_bias = USB2_BIAS_28P15MV, |
| .tx_bias = USB2_BIAS_11P25MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bit = USB2_FULL_BIT_PRE_EMP, |
| }" # USB2_A0 |
| register "usb2_ports[4]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .pre_emp_bias = USB2_BIAS_28P15MV, |
| .tx_bias = USB2_BIAS_0MV, |
| .tx_emp_enable = USB2_DE_EMP_ON, |
| .pre_emp_bit = USB2_FULL_BIT_PRE_EMP, |
| }" # uSD |
| register "usb2_ports[5]" = "{ |
| .enable = 1, |
| .ocpin = OC_SKIP, |
| .tx_bias = USB2_BIAS_0MV, |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, |
| .pre_emp_bias = USB2_BIAS_28P15MV, |
| .pre_emp_bit = USB2_FULL_BIT_PRE_EMP, |
| }" # UFCamera |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN |
| |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A port A1 |
| |
| register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC_SKIP)" |
| register "tcss_ports[1]" = "TCSS_PORT_DEFAULT(OC_SKIP)" |
| |
| register "serial_io_i2c_mode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoPci, |
| [PchSerialIoIndexI2C4] = PchSerialIoPci, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| |
| # Configure external V1P05/Vnn/VnnSx Rails |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 1, |
| .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0, |
| .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX , |
| .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX , |
| .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL, |
| .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_RETENTION, |
| .v1p05_voltage_mv = 1050, |
| .vnn_voltage_mv = 780, |
| .vnn_sx_voltage_mv = 1050, |
| .v1p05_icc_max_ma = 500, |
| .vnn_icc_max_ma = 500, |
| }" |
| |
| # VR Settings |
| register "domain_vr_config[VR_DOMAIN_IA]" = "{ |
| .vr_config_enable = 1, |
| .tdc_timewindow = 1000, |
| .ac_loadline = 500, |
| .dc_loadline = 500, |
| .psi1threshold = VR_CFG_AMP(20), |
| .psi2threshold = VR_CFG_AMP(5), |
| .psi3threshold = VR_CFG_AMP(1), |
| }" |
| |
| register "domain_vr_config[VR_DOMAIN_GT]" = "{ |
| .vr_config_enable = 1, |
| .tdc_timewindow = 1000, |
| .psi1threshold = VR_CFG_AMP(13), |
| .psi2threshold = VR_CFG_AMP(5), |
| .psi3threshold = VR_CFG_AMP(1), |
| |
| }" |
| |
| # Enable the Cnvi BT Audio Offload |
| register "cnvi_bt_audio_offload" = "1" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| I2C0 | TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C1 | Touchscreen | |
| #| I2C2 | WCAM | |
| #| I2C3 | Audio | |
| #| I2C4 | EMR | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .panel_orientation = LB_FB_ORIENTATION_RIGHT_UP, |
| .i2c[0] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST_PLUS, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .scl_lcnt = 55, |
| .scl_hcnt = 30, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 157, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 157, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[4] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| }" |
| |
| device domain 0 on |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""Memory"" |
| register "options.tsr[1].desc" = ""Charger"" |
| register "options.tsr[2].desc" = ""Ambient"" |
| register "options.tsr[3].desc" = ""Sub Charger"" |
| |
| # TODO: below values are initial reference values only |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), |
| [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 75, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), |
| [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 85, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 3000, |
| .max_power = 6000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200 |
| }, |
| .pl2 = { |
| .min_power = 25000, |
| .max_power = 25000, |
| .time_window_min = 1, |
| .time_window_max = 1, |
| .granularity = 1000 |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| device generic 0 on end |
| end |
| end |
| device ref ipu on |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| register "cio2_num_ports" = "1" |
| register "cio2_lanes_used" = "{4}" # 4 CSI Camera lanes are used |
| register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0"" |
| register "cio2_prt[0]" = "2" |
| device generic 0 on |
| probe WFC WFC_MIPI_OV8856 |
| end |
| end |
| end |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "enable_cnvi_ddr_rfim" = "true" |
| device generic 0 on end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""HX121A"" |
| register "generic.desc" = ""HX Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.probed" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "200" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x1" |
| device i2c 0x4F on end |
| end |
| end |
| device ref i2c2 on |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI8856"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 8856 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "4" |
| register "ssdb.link_used" = "1" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "2" |
| register "link_freq[0]" = "360000000" |
| register "link_freq[1]" = "180000000" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| #Controls |
| register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" |
| register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1800_PP1200_WCAM_X |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 36 on |
| probe WFC WFC_MIPI_OV8856 |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "3" |
| register "acpi_name" = ""VCM0"" |
| register "chip_name" = ""DW AF DAC"" |
| register "device_type" = "INTEL_ACPI_CAMERA_VCM" |
| |
| register "pr0" = ""\\_SB.PCI0.I2C2.CAM0.PRIC"" |
| register "vcm_compat" = ""dongwoon,dw9714"" |
| |
| device i2c 0C on |
| probe WFC WFC_MIPI_OV8856 |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" |
| register "acpi_uid" = "1" |
| register "acpi_name" = ""NVM0"" |
| register "chip_name" = ""GT24C08"" |
| register "device_type" = "INTEL_ACPI_CAMERA_NVM" |
| |
| register "pr0" = ""\\_SB.PCI0.I2C2.CAM0.PRIC"" |
| |
| register "nvm_size" = "0x2000" |
| register "nvm_pagesize" = "1" |
| register "nvm_readonly" = "1" |
| register "nvm_width" = "0x10" |
| register "nvm_compat" = ""atmel,24c08"" |
| |
| device i2c 50 on |
| probe WFC WFC_MIPI_OV8856 |
| end |
| end |
| end |
| device ref i2c3 on |
| chip drivers/i2c/da7219 |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| register "btn_cfg" = "50" |
| register "mic_det_thr" = "500" |
| register "jack_ins_deb" = "20" |
| register "jack_det_rate" = ""32ms_64ms"" |
| register "jack_rem_deb" = "1" |
| register "a_d_btn_thr" = "0xa" |
| register "d_b_btn_thr" = "0x16" |
| register "b_c_btn_thr" = "0x21" |
| register "c_mic_btn_thr" = "0x3e" |
| register "btn_avg" = "4" |
| register "adc_1bit_rpt" = "1" |
| register "micbias_lvl" = "2600" |
| register "mic_amp_in_sel" = ""diff"" |
| device i2c 1a on end |
| end |
| end |
| device ref i2c4 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""WCOM014B"" |
| register "generic.desc" = ""WCOM Digitizer"" |
| register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_F12)" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "20" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_F16)" |
| register "generic.reset_delay_ms" = "100" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x1" |
| device i2c 0x09 on |
| probe STYLUS STYLUS_PRESENT |
| end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ZNT0000"" |
| register "generic.desc" = ""Zinitix Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0xE" |
| device i2c 40 on end |
| end |
| end |
| device ref hda on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98360A"" |
| register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "sdmode_delay" = "5" |
| device generic 0 on end |
| end |
| chip drivers/sof |
| register "spkr_tplg" = "max98360a" |
| register "jack_tplg" = "da7219" |
| register "mic_tplg" = "_2ch_pdm0" |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp7 off end |
| device ref pcie_rp9 off end |
| device ref emmc on |
| probe STORAGE STORAGE_EMMC |
| end |
| device ref ish on |
| chip drivers/intel/ish |
| register "add_acpi_dma_property" = "true" |
| device generic 0 on end |
| end |
| end |
| device ref ufs on |
| probe STORAGE STORAGE_UFS |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port2 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 SDCard"" |
| register "type" = "UPC_TYPE_EXPRESSCARD" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb3_port2 on end |
| end |
| end |
| end |
| end |
| end |
| end |