| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2007-2010 coresystems GmbH |
| * Copyright (C) 2011 The ChromiumOS Authors. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; version 2 of the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA |
| */ |
| |
| #include <stdint.h> |
| #include <stddef.h> |
| #include <console/console.h> |
| #include <cpu/intel/haswell/haswell.h> |
| #include <northbridge/intel/haswell/haswell.h> |
| #include <northbridge/intel/haswell/raminit.h> |
| #include <southbridge/intel/lynxpoint/pch.h> |
| #include "gpio.h" |
| |
| const struct rcba_config_instruction rcba_config[] = { |
| /* |
| * GFX INTA -> PIRQA (MSI) |
| * D28IP_P1IP WLAN INTA -> PIRQB |
| * D28IP_P4IP ETH0 INTB -> PIRQC |
| * D29IP_E1P EHCI1 INTA -> PIRQD |
| * D26IP_E2P EHCI2 INTA -> PIRQE |
| * D31IP_SIP SATA INTA -> PIRQF (MSI) |
| * D31IP_SMIP SMBUS INTB -> PIRQG |
| * D31IP_TTIP THRT INTC -> PIRQH |
| * D27IP_ZIP HDA INTA -> PIRQG (MSI) |
| */ |
| |
| /* Device interrupt pin register (board specific) */ |
| RCBA_SET_REG_32(D31IP, (INTC << D31IP_TTIP) | (NOINT << D31IP_SIP2) | |
| (INTB << D31IP_SMIP) | (INTA << D31IP_SIP)), |
| RCBA_SET_REG_32(D30IP, (NOINT << D30IP_PIP)), |
| RCBA_SET_REG_32(D29IP, (INTA << D29IP_E1P)), |
| RCBA_SET_REG_32(D28IP, (INTA << D28IP_P1IP) | (INTC << D28IP_P3IP) | |
| (INTB << D28IP_P4IP)), |
| RCBA_SET_REG_32(D27IP, (INTA << D27IP_ZIP)), |
| RCBA_SET_REG_32(D26IP, (INTA << D26IP_E2P)), |
| RCBA_SET_REG_32(D25IP, (NOINT << D25IP_LIP)), |
| RCBA_SET_REG_32(D22IP, (NOINT << D22IP_MEI1IP)), |
| |
| /* Device interrupt route registers */ |
| RCBA_SET_REG_32(D31IR, DIR_ROUTE(PIRQF, PIRQG, PIRQH, PIRQA)), |
| RCBA_SET_REG_32(D29IR, DIR_ROUTE(PIRQD, PIRQE, PIRQF, PIRQG)), |
| RCBA_SET_REG_32(D28IR, DIR_ROUTE(PIRQB, PIRQC, PIRQD, PIRQE)), |
| RCBA_SET_REG_32(D27IR, DIR_ROUTE(PIRQG, PIRQH, PIRQA, PIRQB)), |
| RCBA_SET_REG_32(D26IR, DIR_ROUTE(PIRQE, PIRQF, PIRQG, PIRQH)), |
| RCBA_SET_REG_32(D25IR, DIR_ROUTE(PIRQA, PIRQB, PIRQC, PIRQD)), |
| RCBA_SET_REG_32(D22IR, DIR_ROUTE(PIRQA, PIRQB, PIRQC, PIRQD)), |
| |
| /* Disable unused devices (board specific) */ |
| RCBA_RMW_REG_32(FD, ~0, PCH_DISABLE_ALWAYS), |
| |
| RCBA_END_CONFIG, |
| }; |
| |
| void mainboard_romstage_entry(unsigned long bist) |
| { |
| struct pei_data pei_data = { |
| .pei_version = PEI_VERSION, |
| .mchbar = DEFAULT_MCHBAR, |
| .dmibar = DEFAULT_DMIBAR, |
| .epbar = DEFAULT_EPBAR, |
| .pciexbar = DEFAULT_PCIEXBAR, |
| .smbusbar = SMBUS_IO_BASE, |
| .wdbbar = 0x4000000, |
| .wdbsize = 0x1000, |
| .hpet_address = HPET_ADDR, |
| .rcba = DEFAULT_RCBA, |
| .pmbase = DEFAULT_PMBASE, |
| .gpiobase = DEFAULT_GPIOBASE, |
| .temp_mmio_base = 0xfed08000, |
| .system_type = 0, // 0 Mobile, 1 Desktop/Server |
| .tseg_size = CONFIG_SMM_TSEG_SIZE, |
| .spd_addresses = { 0xa0, 0xa2, 0xa4, 0xa6 }, |
| .ec_present = 0, |
| // 0 = leave channel enabled |
| // 1 = disable dimm 0 on channel |
| // 2 = disable dimm 1 on channel |
| // 3 = disable dimm 0+1 on channel |
| .dimm_channel0_disabled = 0, |
| .dimm_channel1_disabled = 0, |
| .max_ddr3_freq = 1600, |
| .usb2_ports = { |
| /* Length, Enable, OCn#, Location */ |
| { 0x0040, 1, 0, /* P0: Back USB3 port (OC0) */ |
| USB_PORT_BACK_PANEL }, |
| { 0x0040, 1, 0, /* P1: Back USB3 port (OC0) */ |
| USB_PORT_BACK_PANEL }, |
| { 0x0040, 1, 1, /* P2: Flex Port on bottom (OC1) */ |
| USB_PORT_FLEX }, |
| { 0x0040, 1, USB_OC_PIN_SKIP, /* P3: Dock connector */ |
| USB_PORT_DOCK }, |
| { 0x0040, 1, USB_OC_PIN_SKIP, /* P4: Mini PCIE */ |
| USB_PORT_MINI_PCIE }, |
| { 0x0040, 1, 1, /* P5: USB eSATA header (OC1) */ |
| USB_PORT_FLEX }, |
| { 0x0040, 1, 3, /* P6: Front Header J8H2 (OC3) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 3, /* P7: Front Header J8H2 (OC3) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 4, /* P8: USB/LAN Jack (OC4) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 4, /* P9: USB/LAN Jack (OC4) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 5, /* P10: Front Header J7H3 (OC5) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 5, /* P11: Front Header J7H3 (OC5) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 6, /* P12: USB/DP Jack (OC6) */ |
| USB_PORT_FRONT_PANEL }, |
| { 0x0040, 1, 6, /* P13: USB/DP Jack (OC6) */ |
| USB_PORT_FRONT_PANEL }, |
| }, |
| .usb3_ports = { |
| /* Enable, OCn# */ |
| { 1, 0 }, /* P1; */ |
| { 1, 0 }, /* P2; */ |
| { 1, 0 }, /* P3; */ |
| { 1, 0 }, /* P4; */ |
| { 1, 0 }, /* P6; */ |
| { 1, 0 }, /* P6; */ |
| }, |
| }; |
| |
| struct romstage_params romstage_params = { |
| .pei_data = &pei_data, |
| .gpio_map = &mainboard_gpio_map, |
| .rcba_config = &rcba_config[0], |
| .bist = bist, |
| .copy_spd = NULL, |
| }; |
| |
| /* Call into the real romstage main with this board's attributes. */ |
| romstage_common(&romstage_params); |
| } |