| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <intelblocks/xhci.h> |
| |
| /* |
| * USB Port Wake Enable (UPWE) on usb attach/detach |
| * Arg0 - Port Number |
| * Arg1 - Port 1 Status and control offset |
| * Arg2 - xHCI Memory-mapped address |
| */ |
| Method (UPWE, 3, Serialized) |
| { |
| Local0 = Arg1 + ((Arg0 - 1) * 0x10) |
| |
| /* Map ((XMEM << 16) + Local0 in PSCR */ |
| OperationRegion (PSCR, SystemMemory, (Arg2 << 16) + Local0, 0x10) |
| Field (PSCR, DWordAcc, NoLock, Preserve) |
| { |
| PSCT, 32, |
| } |
| Local0 = PSCT |
| Local0 = Local0 & PORTSCN_BITS_OFF_MASK |
| Local0 = Local0 | PORTSCN_WAKE_ON_BOTH_CONNECT_DISCONNECT_ENABLE |
| PSCT = Local0 |
| } |
| |
| /* |
| * USB Wake Enable Setup (UWES) |
| * Arg0 - Port enable bitmap |
| * Arg1 - Port 1 Status and control offset |
| * Arg2 - xHCI Memory-mapped address |
| */ |
| Method (UWES, 3, Serialized) |
| { |
| Local0 = Arg0 |
| |
| While (1) { |
| FindSetRightBit (Local0, Local1) |
| If (Local1 == 0) { |
| Break |
| } |
| UPWE (Local1, Arg1, Arg2) |
| /* |
| * Clear the lowest set bit in Local0 since it was |
| * processed. |
| */ |
| Local0 = Local0 & (Local0 - 1) |
| } |
| } |
| |
| /* XHCI Controller 0:14.0 */ |
| |
| Device (XHCI) |
| { |
| Name (_ADR, 0x00140000) |
| |
| Name (_PRW, Package () { GPE0_PME_B0, 3 }) |
| |
| Method (_DSW, 3) |
| { |
| PMEE = Arg0 |
| UWES ((\U2WE & 0x3FF), PORTSCN_OFFSET, XMEM) |
| UWES ((\U3WE & 0x3F ), PORTSCXUSB3_OFFSET, XMEM) |
| } |
| |
| Name (_S3D, 3) /* D3 supported in S3 */ |
| Name (_S4D, 3) /* D3 supported in S4 */ |
| Name (_S0W, 3) /* D3 can wake device in S0 */ |
| Name (_S3W, 3) /* D3 can wake system from S3 */ |
| Name (_S4W, 3) /* D3 can wake system from S4 */ |
| |
| OperationRegion (XPRT, PCI_Config, 0x00, 0x100) |
| Field (XPRT, AnyAcc, NoLock, Preserve) |
| { |
| DVID, 16, /* VENDORID */ |
| Offset (0x10), |
| , 16, |
| XMEM, 16, /* MEM_BASE */ |
| Offset (0x50), /* XHCLKGTEN */ |
| , 2, |
| STGE, 1, /* SS Link Trunk clock gating enable */ |
| Offset (0x74), |
| D0D3, 2, /* POWERSTATE */ |
| , 6, |
| PMEE, 1, /* PME_EN */ |
| , 6, |
| PMES, 1, /* PME_STS */ |
| Offset (0xA2), |
| , 2, |
| D3HE, 1, /* D3_hot_en */ |
| } |
| |
| OperationRegion (XREG, SystemMemory, (XMEM << 16) + 0x8000, 0x200) |
| Field (XREG, DWordAcc, Lock, Preserve) |
| { |
| Offset (0x1c4), /* USB2PMCTRL */ |
| , 2, |
| UPSW, 2, /* U2PSUSPGP */ |
| } |
| |
| Method (_PSC, 0, Serialized) |
| { |
| Return (^D0D3) |
| } |
| |
| Method (_PS0, 0, Serialized) |
| { |
| If (^DVID != 0xFFFF) { |
| If (!((^XMEM == 0xFFFF) || (^XMEM == 0x0000))) { |
| |
| /* Disable d3hot and SS link trunk clock gating */ |
| ^D3HE = 0 |
| ^STGE = 0 |
| |
| /* If device is in D3, set back to D0 */ |
| If (^D0D3 == 3) { |
| Local0 = 0 |
| ^D0D3 = Local0 |
| Local0 = ^D0D3 |
| } |
| |
| /* Disable USB2 PHY SUS Well Power Gating */ |
| ^UPSW = 0 |
| |
| /* |
| * Apply USB2 PHPY Power Gating workaround if needed. |
| */ |
| If (^^PMC.UWAB) { |
| /* Write to MTPMC to have PMC disable power gating */ |
| ^^PMC.MPMC = 1 |
| |
| /* Wait for PCH_PM_STS.MSG_FULL_STS to be 0 */ |
| Local0 = 10 |
| While (^^PMC.PMFS) { |
| If (!Local0) { |
| Break |
| } |
| Local0-- |
| Sleep (10) |
| } |
| } |
| } |
| } |
| } |
| |
| Method (_PS3, 0, Serialized) |
| { |
| If (^DVID != 0xFFFF) { |
| If (!((^XMEM == 0xFFFF) || (^XMEM == 0x0000))) { |
| |
| /* Clear PME Status */ |
| ^PMES = 1 |
| |
| /* Enable PME */ |
| ^PMEE= 1 |
| |
| /* If device is in D3, set back to D0 */ |
| If (^D0D3 == 3) { |
| Local0 = 0 |
| ^D0D3 = Local0 |
| Local0 = ^D0D3 |
| } |
| |
| /* Enable USB2 PHY SUS Well Power Gating in D0/D0i2/D0i3/D3 */ |
| ^UPSW = 3 |
| |
| /* Enable d3hot and SS link trunk clock gating */ |
| ^D3HE = 1 |
| ^STGE = 1 |
| |
| /* Now put device in D3 */ |
| Local0 = 3 |
| ^D0D3 = Local0 |
| Local0 = ^D0D3 |
| |
| /* |
| * Apply USB2 PHPY Power Gating workaround if needed. |
| * This code assumes XDCI is disabled, if it is enabled |
| * then this must also check if it is in D3 state too. |
| */ |
| If (^^PMC.UWAB) { |
| /* Write to MTPMC to have PMC enable power gating */ |
| ^^PMC.MPMC = 3 |
| |
| /* Wait for PCH_PM_STS.MSG_FULL_STS to be 0 */ |
| Local0 = 10 |
| While (^^PMC.PMFS) { |
| If (!Local0) { |
| Break |
| } |
| Local0-- |
| Sleep (10) |
| } |
| } |
| } |
| } |
| } |
| |
| /* Root Hub for Skylake-LP PCH */ |
| Device (RHUB) |
| { |
| Name (_ADR, 0) |
| |
| // GPLD: Generate Port Location Data (PLD) |
| Method (GPLD, 1, Serialized) |
| { |
| |
| Name (PCKG, Package (0x01) |
| { |
| Buffer (0x10) {} |
| }) |
| |
| // REV: Revision 0x02 for ACPI 5.0 |
| CreateField (DerefOf (PCKG[0]), 0, 0x07, REV) |
| REV = 0x02 |
| |
| // VISI: Port visibility to user per port |
| CreateField (DerefOf (PCKG[0]), 0x40, 1, VISI) |
| VISI = Arg0 |
| |
| Return (PCKG) |
| } |
| |
| /* USB2 */ |
| Device (HS01) { Name (_ADR, 1) } |
| Device (HS02) { Name (_ADR, 2) } |
| Device (HS03) { Name (_ADR, 3) } |
| Device (HS04) { Name (_ADR, 4) } |
| Device (HS05) { Name (_ADR, 5) } |
| Device (HS06) { Name (_ADR, 6) } |
| Device (HS07) { Name (_ADR, 7) } |
| Device (HS08) { Name (_ADR, 8) } |
| Device (HS09) { Name (_ADR, 9) } |
| Device (HS10) { Name (_ADR, 10) } |
| |
| /* USBr */ |
| Device (USR1) { Name (_ADR, 11) } |
| Device (USR2) { Name (_ADR, 12) } |
| |
| /* USB3 */ |
| Device (SS01) { Name (_ADR, 13) } |
| Device (SS02) { Name (_ADR, 14) } |
| Device (SS03) { Name (_ADR, 15) } |
| Device (SS04) { Name (_ADR, 16) } |
| Device (SS05) { Name (_ADR, 17) } |
| Device (SS06) { Name (_ADR, 18) } |
| } |
| } |