| chip soc/intel/skylake |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route. i.e. If this route changes then the affected GPE |
| # offset bits also need to be changed. |
| register "gpe0_dw0" = "GPP_B" |
| register "gpe0_dw1" = "GPP_D" |
| register "gpe0_dw2" = "GPP_E" |
| |
| register "gen1_dec" = "0x007c0a01" # Super IO SWC |
| register "gen2_dec" = "0x000c0ca1" # IPMI KCS |
| |
| # Additional FSP Configuration |
| # This board has an IGD with no output. |
| register "PrimaryDisplay" = "Display_Auto" |
| |
| # NB: Overcurrent OCx values untested |
| register "usb2_ports" = "{ |
| [0] = USB2_PORT_MID(OC3), /* USB 6 (3.0) */ |
| [1] = USB2_PORT_MID(OC3), /* USB 7 (3.0) */ |
| [2] = USB2_PORT_MID(OC2), /* USB 0 */ |
| [3] = USB2_PORT_MID(OC2), /* USB 1 */ |
| [4] = USB2_PORT_MID(OC1), /* USB 4 */ |
| [5] = USB2_PORT_MID(OC1), /* USB 5 */ |
| [8] = USB2_PORT_MID(OC0), /* USB 2 */ |
| [9] = USB2_PORT_MID(OC0), /* USB 3 */ |
| [10] = USB2_PORT_MID(OC5), /* USB 9 (3.0) */ |
| [11] = USB2_PORT_MID(OC5), /* USB 10 (3.0) */ |
| [12] = USB2_PORT_MID(OC4), /* USB 8 (3.0) */ |
| [13] = USB2_PORT_MID(OC_SKIP), /* IPMI USB hub */ |
| [14] = USB2_PORT_MID(OC0), /* Unknown */ |
| [15] = USB2_PORT_MID(OC0), /* Unknown */ |
| }" |
| |
| register "usb3_ports" = "{ |
| [0] = USB3_PORT_DEFAULT(OC3), /* USB 6 */ |
| [1] = USB3_PORT_DEFAULT(OC3), /* USB 7 */ |
| [2] = USB3_PORT_DEFAULT(OC4), /* USB 8 */ |
| [3] = USB3_PORT_DEFAULT(OC5), /* USB 9 */ |
| [4] = USB3_PORT_DEFAULT(OC5), /* USB 10 */ |
| }" |
| |
| device domain 0 on |
| device pci 01.0 on |
| smbios_slot_desc "SlotTypePciExpressGen3X16" "SlotLengthLong" "CPU SLOT1 PCI-E 3.0 X16" "SlotDataBusWidth16X" |
| end # CPU PCIE Slot JSXB1B |
| device pci 1c.0 on # PCI Express Port 1 |
| register "PcieRpEnable[0]" = "1" |
| device pci 00.0 on end # GbE |
| end |
| device pci 1c.1 on # PCI Express Port 2 |
| register "PcieRpEnable[1]" = "1" |
| device pci 00.0 on end # GbE |
| end |
| device pci 1c.4 on # PCI Express Port 5 |
| register "PcieRpEnable[4]" = "1" |
| smbios_slot_desc "SlotTypeM2Socket3" "SlotLengthOther" "M.2 2280" "SlotDataBusWidth4X" |
| end |
| device pci 1d.0 on # PCI Express Port 9 (Slot JSXB2) |
| register "PcieRpEnable[8]" = "1" |
| smbios_slot_desc "SlotTypePciExpressGen3X4" "SlotLengthShort" "PCH SLOT2 PCI-E 3.0 X4(IN X8)" "SlotDataBusWidth4X" |
| end |
| device pci 1d.4 on # PCI Express Port 13 |
| register "PcieRpEnable[12]" = "1" |
| device pci 00.0 on # Aspeed PCI Bridge |
| device pci 00.0 on end # Aspeed 2400 VGA |
| end |
| end |
| device pci 1f.0 on # LPC Interface |
| chip drivers/ipmi |
| # On cold boot it takes a while for the BMC to start the IPMI service |
| register "wait_for_bmc" = "1" |
| register "bmc_boot_timeout" = "60" |
| device pnp ca2.0 on end # IPMI KCS |
| end |
| chip superio/common |
| device pnp 2e.0 on |
| chip superio/aspeed/ast2400 |
| device pnp 2e.2 on # SUART1 |
| io 0x60 = 0x3f8 |
| irq 0x70 = 4 |
| drq 0xf0 = 0x00 |
| end |
| device pnp 2e.3 on # SUART2 |
| io 0x60 = 0x2f8 |
| irq 0x70 = 3 |
| drq 0xf0 = 0x00 |
| end |
| device pnp 2e.4 on # SWC |
| io 0x60 = 0xa00 |
| io 0x62 = 0xa10 |
| io 0x64 = 0xa20 |
| io 0x66 = 0xa30 |
| irq 0x70 = 0x00 |
| end |
| device pnp 2e.5 off end # KBC |
| device pnp 2e.7 on # GPIO |
| irq 0x70 = 0x00 |
| end |
| device pnp 2e.b off end # SUART3 |
| device pnp 2e.c off end # SUART4 |
| device pnp 2e.d on # iLPC2AHB |
| irq 0x70 = 0x00 |
| end |
| device pnp 2e.e on # Mailbox |
| io 0x60 = 0xa40 |
| irq 0x70 = 0x00 |
| end |
| end |
| end |
| end |
| end |
| end |
| end |