| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2012 secunet Security Networks AG |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; version 2 of |
| * the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| // __PRE_RAM__ means: use "unsigned" for device, not a struct. |
| |
| #include <stdint.h> |
| #include <string.h> |
| #include <arch/io.h> |
| #include <cpu/x86/lapic.h> |
| #include <cpu/x86/msr.h> |
| #include <cpu/x86/tsc.h> |
| #include <arch/acpi.h> |
| #include <cbmem.h> |
| #include <lib.h> |
| #include <pc80/mc146818rtc.h> |
| #include <console/console.h> |
| #include <southbridge/intel/i82801ix/i82801ix.h> |
| #include <northbridge/intel/gm45/gm45.h> |
| #include <superio/smsc/lpc47n227/early_serial.c> |
| |
| #define LPC_DEV PCI_DEV(0, 0x1f, 0) |
| #define SERIAL_DEV PNP_DEV(0x2e, LPC47N227_SP1) |
| |
| static void default_southbridge_gpio_setup(void) |
| { |
| /* Enable GPIOs [31:0]. */ |
| outl(0x197e7dfe, DEFAULT_GPIOBASE + 0x00); |
| /* Set input/output mode [31:0] (0 == out, 1 == in). */ |
| outl(0xe0ea43fe, DEFAULT_GPIOBASE + 0x04); |
| /* Set gpio levels [31:0]. orig: 0x01140800 (~SATA0, ~SATA1, GSM, BT, |
| WLAN, ~ANTMUX, ~GPIO12, |
| ~SUSPWR, SMBALERT) */ |
| outl(0x00000800, DEFAULT_GPIOBASE + 0x0c); |
| |
| /* Disable blink [31:0]. */ |
| outl(0x00000000, DEFAULT_GPIOBASE + 0x18); |
| /* Set input inversion [31:0]. */ |
| outl(0x00000182, DEFAULT_GPIOBASE + 0x2c); |
| |
| /* Enable GPIOs [60:32]. */ |
| outl(0x130300fe, DEFAULT_GPIOBASE + 0x30); |
| /* Set input/output mode [60:32] (0 == out, 1 == in). */ |
| outl(0x0e55ffb0, DEFAULT_GPIOBASE + 0x34); |
| /* Set gpio levels [60:32]. orig: 0x10020046 (LNKALERT, ~ATAIO, |
| DMITERM, TXT, ~CLKSATA, |
| GPS, AUDIO) */ |
| outl(0x10020042, DEFAULT_GPIOBASE + 0x38); |
| } |
| |
| static void early_lpc_setup(void) |
| { |
| /* Set up SuperIO LPC forwards */ |
| |
| /* Configure serial IRQs.*/ |
| pci_write_config8(LPC_DEV, D31F0_SERIRQ_CNTL, 0xd0); |
| /* Map COMa on 0x3f8, COMb on 0x2f8. */ |
| pci_write_config16(LPC_DEV, D31F0_LPC_IODEC, 0x0010); |
| /* Enable COMa, COMb, Kbd, SuperIO at 0x2e, MCs at 0x4e and 0x62/66. */ |
| pci_write_config16(LPC_DEV, D31F0_LPC_EN, 0x3c03); |
| } |
| |
| static void default_superio_gpio_setup(void) |
| { |
| /* Original settings: |
| idx 30 31 32 33 34 35 36 37 38 39 |
| val 60 00 00 40 00 ff 00 e0 00 80 |
| def 00 00 00 00 00 00 00 00 00 80 |
| |
| Values: |
| GP1 GP2 GP3 GP4 |
| fd 17 88 14 |
| */ |
| const device_t sio = PNP_DEV(0x2e, 0); |
| |
| /* Enter super-io's configuration state. */ |
| pnp_enter_conf_state(sio); |
| |
| /* Set lpc47n227's runtime register block's base address. */ |
| pnp_write_config(sio, 0x30, 0x600 >> 4); |
| |
| /* Set GP23 to alternate function. */ |
| pnp_write_config(sio, 0x33, 0x40); |
| |
| /* Set GP30 - GP37 to output mode: COM control */ |
| pnp_write_config(sio, 0x35, 0xff); |
| |
| /* Set GP45 - GP47 to output mode. */ |
| pnp_write_config(sio, 0x37, 0xe0); |
| |
| /* Set nIO_PME to open drain. */ |
| pnp_write_config(sio, 0x39, 0x80); |
| |
| /* Exit configuration state. */ |
| pnp_exit_conf_state(sio); |
| |
| |
| /* Enable decoding of 0x600-0x60f through lpc. */ |
| pci_write_config32(LPC_DEV, D31F0_GEN1_DEC, 0x000c0601); |
| |
| /* Set GPIO output values: */ |
| outb(0x88, 0x600 + 0xb + 3); /* GP30 - GP37 */ |
| outb(0x10, 0x600 + 0xb + 4); /* GP40 - GP47 */ |
| } |
| |
| #include <cpu/intel/romstage.h> |
| void main(unsigned long bist) |
| { |
| sysinfo_t sysinfo; |
| int s3resume = 0; |
| int cbmem_initted; |
| u16 reg16; |
| |
| /* basic northbridge setup, including MMCONF BAR */ |
| gm45_early_init(); |
| |
| if (bist == 0) |
| enable_lapic(); |
| |
| /* First, run everything needed for console output. */ |
| i82801ix_early_init(); |
| early_lpc_setup(); |
| default_superio_gpio_setup(); |
| lpc47n227_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); |
| console_init(); |
| printk(BIOS_DEBUG, "running main(bist = %lu)\n", bist); |
| |
| reg16 = pci_read_config16(LPC_DEV, D31F0_GEN_PMCON_3); |
| pci_write_config16(LPC_DEV, D31F0_GEN_PMCON_3, reg16); |
| if ((MCHBAR16(SSKPD_MCHBAR) == 0xCAFE) && !(reg16 & (1 << 9))) { |
| printk(BIOS_DEBUG, "soft reset detected, rebooting properly\n"); |
| gm45_early_reset(); |
| } |
| |
| default_southbridge_gpio_setup(); |
| |
| /* ASPM related setting, set early by original BIOS. */ |
| DMIBAR16(0x204) &= ~(3 << 10); |
| |
| /* Check for S3 resume. */ |
| const u32 pm1_cnt = inl(DEFAULT_PMBASE + 0x04); |
| if (((pm1_cnt >> 10) & 7) == 5) { |
| if (acpi_s3_resume_allowed()) { |
| printk(BIOS_DEBUG, "Resume from S3 detected.\n"); |
| s3resume = 1; |
| /* Clear SLP_TYPE. This will break stage2 but |
| * we care for that when we get there. |
| */ |
| outl(pm1_cnt & ~(7 << 10), DEFAULT_PMBASE + 0x04); |
| } else { |
| printk(BIOS_DEBUG, "Resume from S3 detected, but disabled.\n"); |
| } |
| } |
| |
| /* RAM initialization */ |
| enter_raminit_or_reset(); |
| memset(&sysinfo, 0, sizeof(sysinfo)); |
| get_gmch_info(&sysinfo); |
| sysinfo.spd_map[0] = 0x50; |
| sysinfo.spd_map[1] = 0; |
| sysinfo.spd_map[2] = 0x52; |
| sysinfo.spd_map[3] = 0; |
| sysinfo.enable_igd = 1; |
| sysinfo.enable_peg = 0; |
| raminit(&sysinfo, s3resume); |
| |
| init_pm(&sysinfo, 1); |
| |
| i82801ix_dmi_setup(); |
| gm45_late_init(sysinfo.stepping); |
| i82801ix_dmi_poll_vc1(); |
| |
| MCHBAR16(SSKPD_MCHBAR) = 0xCAFE; |
| |
| init_iommu(); |
| |
| cbmem_initted = !cbmem_recovery(s3resume); |
| #if CONFIG_HAVE_ACPI_RESUME |
| /* If there is no high memory area, we didn't boot before, so |
| * this is not a resume. In that case we just create the cbmem toc. |
| */ |
| if (s3resume && cbmem_initted) { |
| void *resume_backup_memory = cbmem_find(CBMEM_ID_RESUME); |
| |
| /* copy 1MB - 64K to high tables ram_base to prevent memory corruption |
| * through stage 2. We could keep stuff like stack and heap in high tables |
| * memory completely, but that's a wonderful clean up task for another |
| * day. |
| */ |
| if (resume_backup_memory) |
| memcpy(resume_backup_memory, (void *)CONFIG_RAMBASE, HIGH_MEMORY_SAVE); |
| |
| /* Magic for S3 resume */ |
| pci_write_config32(PCI_DEV(0, 0, 0), D0F0_SKPD, SKPAD_ACPI_S3_MAGIC); |
| } else { |
| /* Magic for S3 resume */ |
| pci_write_config32(PCI_DEV(0, 0, 0), D0F0_SKPD, SKPAD_NORMAL_BOOT_MAGIC); |
| } |
| #endif |
| printk(BIOS_SPEW, "exit main()\n"); |
| } |