| chip northbridge/intel/sandybridge |
| # IGD Displays |
| register "gfx.ndid" = "3" |
| register "gfx.did" = "{ 0x80000100, 0x80000240, 0x80000410, 0x80000410, 0x00000005 }" |
| |
| # Enable DisplayPort B Hotplug with 6ms pulse |
| register "gpu_dp_b_hotplug" = "0x06" |
| |
| # Enable Panel as eDP and configure power delays |
| register "gpu_panel_port_select" = "0" # LVDS |
| register "gpu_panel_power_cycle_delay" = "5" # 400ms |
| register "gpu_panel_power_up_delay" = "500" # 50ms |
| register "gpu_panel_power_down_delay" = "150" # 15ms |
| register "gpu_panel_power_backlight_on_delay" = "2100" # 210ms |
| register "gpu_panel_power_backlight_off_delay" = "2100" # 210ms |
| |
| # Set backlight PWM values |
| register "gpu_cpu_backlight" = "0x000001d4" |
| register "gpu_pch_backlight" = "0x03aa0000" |
| |
| device cpu_cluster 0 on |
| chip cpu/intel/socket_rPGA989 |
| device lapic 0 on end |
| end |
| chip cpu/intel/model_206ax |
| # Magic APIC ID to locate this chip |
| device lapic 0xACAC off end |
| |
| register "c1_acpower" = "1" # ACPI(C1) = MWAIT(C1) |
| register "c2_acpower" = "3" # ACPI(C2) = MWAIT(C3) |
| register "c3_acpower" = "5" # ACPI(C3) = MWAIT(C7) |
| |
| register "c1_battery" = "1" # ACPI(C1) = MWAIT(C1) |
| register "c2_battery" = "3" # ACPI(C2) = MWAIT(C3) |
| register "c3_battery" = "5" # ACPI(C3) = MWAIT(C7) |
| end |
| end |
| |
| device domain 0 on |
| device pci 00.0 on end # host bridge |
| device pci 02.0 on end # vga controller |
| |
| chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH |
| # GPI routing |
| # 0 No effect (default) |
| # 1 SMI# (if corresponding ALT_GPI_SMI_EN bit is also set) |
| # 2 SCI (if corresponding GPIO_EN bit is also set) |
| # Set Lid Switch to SMI to capture in recovery mode. It gets reset to |
| # SCI mode when we go to ACPI mode. |
| register "alt_gp_smi_en" = "0x8100" |
| register "gpi7_routing" = "2" |
| register "gpi8_routing" = "1" |
| register "gpi15_routing" = "1" #lid switch gpe |
| |
| register "sata_port_map" = "0x1" |
| |
| # EC range is 0xFD60 (EC_IO) and 0x68/0x6C |
| register "gen1_dec" = "0x0004fd61" |
| register "gen2_dec" = "0x00040069" |
| |
| # Enable zero-based linear PCIe root port functions |
| register "pcie_port_coalesce" = "1" |
| |
| register "c2_latency" = "1" |
| register "p_cnt_throttling_supported" = "0" |
| |
| device pci 16.0 on end # Management Engine Interface 1 |
| device pci 16.1 off end # Management Engine Interface 2 |
| device pci 16.2 off end # Management Engine IDE-R |
| device pci 16.3 off end # Management Engine KT |
| device pci 19.0 off end # Intel Gigabit Ethernet |
| device pci 1a.0 on end # USB2 EHCI #2 |
| device pci 1b.0 on end # High Definition Audio |
| device pci 1c.0 off end # PCIe Port #1 |
| device pci 1c.1 on end # PCIe Port #2 (WLAN) |
| device pci 1c.2 on end # PCIe Port #3 (ETH0) |
| device pci 1c.3 off end # PCIe Port #4 |
| device pci 1c.4 off end # PCIe Port #5 |
| device pci 1c.5 off end # PCIe Port #6 |
| device pci 1c.6 off end # PCIe Port #7 |
| device pci 1c.7 off end # PCIe Port #8 |
| device pci 1d.0 on end # USB2 EHCI #1 |
| device pci 1e.0 off end # PCI bridge |
| device pci 1f.0 on |
| chip ec/compal/ene932 |
| # 60/64 KBC |
| device pnp ff.1 on # dummy address |
| end |
| end |
| end # LPC bridge |
| device pci 1f.2 on end # SATA Controller 1 |
| device pci 1f.3 on end # SMBus |
| device pci 1f.5 off end # SATA Controller 2 |
| device pci 1f.6 on end # Thermal |
| end |
| end |
| end |