| chip soc/intel/braswell |
| |
| ############################################################ |
| # Set the parameters for MemoryInit |
| ############################################################ |
| |
| register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB |
| |
| register "PcdMrcInitMmioSize" = "0x0800" |
| register "PcdMrcInitSpdAddr1" = "0xa0" |
| register "PcdMrcInitSpdAddr2" = "0xa2" |
| register "PcdIgdDvmt50PreAlloc" = "1" |
| register "PcdApertureSize" = "2" |
| register "PcdGttSize" = "1" |
| register "PcdDvfsEnable" = "1" |
| |
| ############################################################ |
| # Set the parameters for SiliconInit |
| ############################################################ |
| |
| register "PcdSdcardMode" = "PCH_ACPI_MODE" |
| register "PcdEnableHsuart0" = "0" |
| register "PcdEnableHsuart1" = "1" |
| register "PcdEnableAzalia" = "1" |
| register "PcdEnableXhci" = "1" |
| register "PcdEnableLpe" = "1" |
| register "PcdEnableDma0" = "1" |
| register "PcdEnableDma1" = "1" |
| register "PcdEnableI2C0" = "1" |
| register "PcdEnableI2C1" = "1" |
| register "PcdEnableI2C2" = "0" |
| register "PcdEnableI2C3" = "0" |
| register "PcdEnableI2C4" = "0" |
| register "PcdEnableI2C5" = "1" |
| register "PcdEnableI2C6" = "0" |
| register "PunitPwrConfigDisable" = "0" # Enable SVID |
| register "ChvSvidConfig" = "SVID_CONFIG1" |
| register "PcdEmmcMode" = "PCH_ACPI_MODE" |
| register "PcdUsb3ClkSsc" = "1" |
| register "PcdDispClkSsc" = "1" |
| register "PcdSataClkSsc" = "1" |
| register "PcdEnableSata" = "0" # Disable SATA |
| register "Usb2Port0PerPortPeTxiSet" = "7" |
| register "Usb2Port0PerPortTxiSet" = "5" |
| register "Usb2Port0IUsbTxEmphasisEn" = "2" |
| register "Usb2Port0PerPortTxPeHalf" = "1" |
| register "Usb2Port1PerPortPeTxiSet" = "7" |
| register "Usb2Port1PerPortTxiSet" = "3" |
| register "Usb2Port1IUsbTxEmphasisEn" = "2" |
| register "Usb2Port1PerPortTxPeHalf" = "1" |
| register "Usb2Port2PerPortPeTxiSet" = "7" |
| register "Usb2Port2PerPortTxiSet" = "3" |
| register "Usb2Port2IUsbTxEmphasisEn" = "2" |
| register "Usb2Port2PerPortTxPeHalf" = "1" |
| register "Usb2Port3PerPortPeTxiSet" = "7" |
| register "Usb2Port3PerPortTxiSet" = "3" |
| register "Usb2Port3IUsbTxEmphasisEn" = "2" |
| register "Usb2Port3PerPortTxPeHalf" = "1" |
| register "Usb2Port4PerPortPeTxiSet" = "7" |
| register "Usb2Port4PerPortTxiSet" = "3" |
| register "Usb2Port4IUsbTxEmphasisEn" = "2" |
| register "Usb2Port4PerPortTxPeHalf" = "1" |
| register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" |
| register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" |
| register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" |
| register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" |
| register "PcdSataInterfaceSpeed" = "3" |
| register "PcdPchSsicEnable" = "1" |
| register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM |
| register "PMIC_I2CBus" = "0" |
| register "ISPEnable" = "0" # Disable IUNIT |
| register "ISPPciDevConfig" = "3" |
| |
| # LPE audio codec settings |
| register "lpe_codec_clk_freq" = "25" # 25MHz clock |
| register "lpe_codec_clk_num" = "0" # PMC_PLT_CLK[0] |
| |
| # Enable devices in ACPI mode |
| register "lpss_acpi_mode" = "1" |
| register "emmc_acpi_mode" = "1" |
| register "sd_acpi_mode" = "1" |
| register "lpe_acpi_mode" = "1" |
| |
| # Disable SLP_X stretching after SUS power well fail. |
| register "disable_slp_x_stretch_sus_fail" = "1" |
| |
| # Allow PCIe devices to wake system from suspend |
| register "pcie_wake_enable" = "1" |
| |
| device cpu_cluster 0 on |
| device lapic 0 on end |
| end |
| device domain 0 on |
| # EDS Table 24-4, Figure 24-5 |
| device pci 00.0 on end # 8086 2280 - SoC transaction router |
| device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display |
| device pci 03.0 on end # 8086 22b8 - Camera and Image Processor |
| device pci 0b.0 on end # 8086 22dc - ? |
| device pci 10.0 on end # 8086 2294 - MMC Port |
| device pci 11.0 off end # 8086 0F15 - SDIO Port |
| device pci 12.0 on end # 8086 0F16 - SD Port |
| device pci 13.0 off end # 8086 22a3 - Sata controller |
| device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time |
| device pci 15.0 on end # 8086 22a8 - LP Engine Audio |
| device pci 16.0 off end # 8086 22b7 - USB device |
| device pci 18.0 on end # 8086 22c0 - SIO - DMA |
| device pci 18.1 on end # 8086 22c1 - I2C Port 1 |
| device pci 18.2 on end # 8086 22c2 - I2C Port 2 |
| device pci 18.3 off end # 8086 22c3 - I2C Port 3 |
| device pci 18.4 off end # 8086 22c4 - I2C Port 4 |
| device pci 18.5 off end # 8086 22c5 - I2C Port 5 |
| device pci 18.6 on end # 8086 22c6 - I2C Port 6 |
| device pci 18.7 off end # 8086 22c7 - I2C Port 7 |
| device pci 1a.0 on end # 8086 0F18 - Trusted Execution Engine |
| device pci 1b.0 on end # 8086 0F04 - HD Audio |
| device pci 1c.0 on end # 8086 0000 - PCIe Root Port 1 |
| device pci 1c.1 on end # 8086 0000 - PCIe Root Port 2 |
| device pci 1c.2 on end # 8086 0000 - PCIe Root Port 3 |
| device pci 1c.3 on end # 8086 0000 - PCIe Root Port 4 |
| device pci 1e.0 on end # 8086 2286 - SIO - DMA |
| device pci 1e.1 off end # 8086 0F08 - PWM 1 |
| device pci 1e.2 off end # 8086 0F09 - PWM 2 |
| device pci 1e.3 on end # 8086 228a - HSUART 1 |
| device pci 1e.4 on end # 8086 228c - HSUART 2 |
| device pci 1e.5 on end # 8086 228e - SPI 1 |
| device pci 1e.6 on end # 8086 2290 - SPI 2 |
| device pci 1e.7 on end # 8086 22ac - SPI 3 |
| device pci 1f.0 on # 8086 229c - LPC bridge |
| chip drivers/pc80/tpm |
| # Rising edge interrupt |
| register "irq_polarity" = "2" |
| device pnp 0c31.0 on |
| irq 0x70 = 10 |
| end |
| end |
| chip ec/google/chromeec |
| device pnp 0c09.0 on end |
| end |
| end # LPC Bridge |
| device pci 1f.3 off end # 8086 0F12 - SMBus 0 |
| end |
| end |