haswell: Add initial support for Haswell platforms
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
diff --git a/src/southbridge/intel/lynxpoint/sata.c b/src/southbridge/intel/lynxpoint/sata.c
new file mode 100644
index 0000000..0761323
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/sata.c
@@ -0,0 +1,290 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include "pch.h"
+
+typedef struct southbridge_intel_lynxpoint_config config_t;
+
+static inline u32 sir_read(struct device *dev, int idx)
+{
+ pci_write_config32(dev, SATA_SIRI, idx);
+ return pci_read_config32(dev, SATA_SIRD);
+}
+
+static inline void sir_write(struct device *dev, int idx, u32 value)
+{
+ pci_write_config32(dev, SATA_SIRI, idx);
+ pci_write_config32(dev, SATA_SIRD, value);
+}
+
+static void sata_init(struct device *dev)
+{
+ u32 reg32;
+ u16 reg16;
+ /* Get the chip configuration */
+ config_t *config = dev->chip_info;
+
+ printk(BIOS_DEBUG, "SATA: Initializing...\n");
+
+ if (config == NULL) {
+ printk(BIOS_ERR, "SATA: ERROR: Device not in devicetree.cb!\n");
+ return;
+ }
+
+ /* SATA configuration */
+
+ /* Enable BARs */
+ pci_write_config16(dev, PCI_COMMAND, 0x0007);
+
+ if (config->ide_legacy_combined) {
+ printk(BIOS_DEBUG, "SATA: Controller in combined mode.\n");
+
+ /* No AHCI: clear AHCI base */
+ pci_write_config32(dev, 0x24, 0x00000000);
+ /* And without AHCI BAR no memory decoding */
+ reg16 = pci_read_config16(dev, PCI_COMMAND);
+ reg16 &= ~PCI_COMMAND_MEMORY;
+ pci_write_config16(dev, PCI_COMMAND, reg16);
+
+ pci_write_config8(dev, 0x09, 0x80);
+
+ /* Set timings */
+ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+ IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
+ pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+ IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
+ IDE_PPE0 | IDE_IE0 | IDE_TIME0);
+
+ /* Sync DMA */
+ pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0);
+ pci_write_config16(dev, IDE_SDMA_TIM, 0x0200);
+
+ /* Set IDE I/O Configuration */
+ reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
+ pci_write_config32(dev, IDE_CONFIG, reg32);
+
+ /* Port enable */
+ reg16 = pci_read_config16(dev, 0x92);
+ reg16 &= ~0x3f;
+ reg16 |= config->sata_port_map;
+ pci_write_config16(dev, 0x92, reg16);
+
+ /* SATA Initialization register */
+ pci_write_config32(dev, 0x94,
+ ((config->sata_port_map ^ 0x3f) << 24) | 0x183);
+ } else if(config->sata_ahci) {
+ u32 abar;
+
+ printk(BIOS_DEBUG, "SATA: Controller in AHCI mode.\n");
+
+ /* Set Interrupt Line */
+ /* Interrupt Pin is set by D31IP.PIP */
+ pci_write_config8(dev, INTR_LN, 0x0a);
+
+ /* Set timings */
+ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+ IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
+ IDE_PPE0 | IDE_IE0 | IDE_TIME0);
+ pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+ IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
+
+ /* Sync DMA */
+ pci_write_config16(dev, IDE_SDMA_CNT, IDE_PSDE0);
+ pci_write_config16(dev, IDE_SDMA_TIM, 0x0001);
+
+ /* Set IDE I/O Configuration */
+ reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
+ pci_write_config32(dev, IDE_CONFIG, reg32);
+
+ /* for AHCI, Port Enable is managed in memory mapped space */
+ reg16 = pci_read_config16(dev, 0x92);
+ reg16 &= ~0x3f; /* 6 ports SKU + ORM */
+ reg16 |= 0x8000 | config->sata_port_map;
+ pci_write_config16(dev, 0x92, reg16);
+
+ /* SATA Initialization register */
+ pci_write_config32(dev, 0x94,
+ ((config->sata_port_map ^ 0x3f) << 24) | 0x183);
+
+ /* Initialize AHCI memory-mapped space */
+ abar = pci_read_config32(dev, PCI_BASE_ADDRESS_5);
+ printk(BIOS_DEBUG, "ABAR: %08X\n", abar);
+ /* CAP (HBA Capabilities) : enable power management */
+ reg32 = read32(abar + 0x00);
+ reg32 |= 0x0c006000; // set PSC+SSC+SALP+SSS
+ reg32 &= ~0x00020060; // clear SXS+EMS+PMS
+ write32(abar + 0x00, reg32);
+ /* PI (Ports implemented) */
+ write32(abar + 0x0c, config->sata_port_map);
+ (void) read32(abar + 0x0c); /* Read back 1 */
+ (void) read32(abar + 0x0c); /* Read back 2 */
+ /* CAP2 (HBA Capabilities Extended)*/
+ reg32 = read32(abar + 0x24);
+ reg32 &= ~0x00000002;
+ write32(abar + 0x24, reg32);
+ /* VSP (Vendor Specific Register */
+ reg32 = read32(abar + 0xa0);
+ reg32 &= ~0x00000005;
+ write32(abar + 0xa0, reg32);
+ } else {
+ printk(BIOS_DEBUG, "SATA: Controller in plain mode.\n");
+
+ /* No AHCI: clear AHCI base */
+ pci_write_config32(dev, 0x24, 0x00000000);
+
+ /* And without AHCI BAR no memory decoding */
+ reg16 = pci_read_config16(dev, PCI_COMMAND);
+ reg16 &= ~PCI_COMMAND_MEMORY;
+ pci_write_config16(dev, PCI_COMMAND, reg16);
+
+ /* Native mode capable on both primary and secondary (0xa)
+ * or'ed with enabled (0x50) = 0xf
+ */
+ pci_write_config8(dev, 0x09, 0x8f);
+
+ /* Set Interrupt Line */
+ /* Interrupt Pin is set by D31IP.PIP */
+ pci_write_config8(dev, INTR_LN, 0xff);
+
+ /* Set timings */
+ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+ IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
+ IDE_PPE0 | IDE_IE0 | IDE_TIME0);
+ pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+ IDE_SITRE | IDE_ISP_3_CLOCKS |
+ IDE_RCT_1_CLOCKS | IDE_IE0 | IDE_TIME0);
+
+ /* Sync DMA */
+ pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0 | IDE_PSDE0);
+ pci_write_config16(dev, IDE_SDMA_TIM, 0x0201);
+
+ /* Set IDE I/O Configuration */
+ reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
+ pci_write_config32(dev, IDE_CONFIG, reg32);
+
+ /* Port enable */
+ reg16 = pci_read_config16(dev, 0x92);
+ reg16 &= ~0x3f;
+ reg16 |= config->sata_port_map;
+ pci_write_config16(dev, 0x92, reg16);
+
+ /* SATA Initialization register */
+ pci_write_config32(dev, 0x94,
+ ((config->sata_port_map ^ 0x3f) << 24) | 0x183);
+ }
+
+ /* Set Gen3 Transmitter settings if needed */
+ if (config->sata_port0_gen3_tx)
+ pch_iobp_update(SATA_IOBP_SP0G3IR, 0,
+ config->sata_port0_gen3_tx);
+
+ if (config->sata_port1_gen3_tx)
+ pch_iobp_update(SATA_IOBP_SP1G3IR, 0,
+ config->sata_port1_gen3_tx);
+
+ /* Additional Programming Requirements */
+ sir_write(dev, 0x04, 0x00001600);
+ sir_write(dev, 0x28, 0xa0000033);
+ reg32 = sir_read(dev, 0x54);
+ reg32 &= 0xff000000;
+ reg32 |= 0x5555aa;
+ sir_write(dev, 0x54, reg32);
+ sir_write(dev, 0x64, 0xcccc8484);
+ reg32 = sir_read(dev, 0x68);
+ reg32 &= 0xffff0000;
+ reg32 |= 0xcccc;
+ sir_write(dev, 0x68, reg32);
+ reg32 = sir_read(dev, 0x78);
+ reg32 &= 0x0000ffff;
+ reg32 |= 0x88880000;
+ sir_write(dev, 0x78, reg32);
+ sir_write(dev, 0x84, 0x001c7000);
+ sir_write(dev, 0x88, 0x88338822);
+ sir_write(dev, 0xa0, 0x001c7000);
+ // a4
+ sir_write(dev, 0xc4, 0x0c0c0c0c);
+ sir_write(dev, 0xc8, 0x0c0c0c0c);
+ sir_write(dev, 0xd4, 0x10000000);
+
+ pch_iobp_update(0xea004001, 0x3fffffff, 0xc0000000);
+ pch_iobp_update(0xea00408a, 0xfffffcff, 0x00000100);
+}
+
+static void sata_enable(device_t dev)
+{
+ /* Get the chip configuration */
+ config_t *config = dev->chip_info;
+ u16 map = 0;
+
+ if (!config)
+ return;
+
+ /*
+ * Set SATA controller mode early so the resource allocator can
+ * properly assign IO/Memory resources for the controller.
+ */
+ if (config->sata_ahci)
+ map = 0x0060;
+
+ map |= (config->sata_port_map ^ 0x3f) << 8;
+
+ pci_write_config16(dev, 0x90, map);
+}
+
+static void sata_set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ if (!vendor || !device) {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ pci_read_config32(dev, PCI_VENDOR_ID));
+ } else {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+ }
+}
+
+static struct pci_operations sata_pci_ops = {
+ .set_subsystem = sata_set_subsystem,
+};
+
+static struct device_operations sata_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = sata_init,
+ .enable = sata_enable,
+ .scan_bus = 0,
+ .ops_pci = &sata_pci_ops,
+};
+
+static const unsigned short pci_device_ids[] = { 0x1c00, 0x1c01, 0x1c02, 0x1c03,
+ 0x1e00, 0x1e01, 0x1e02, 0x1e03,
+ 0 };
+
+static const struct pci_driver pch_sata __pci_driver = {
+ .ops = &sata_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .devices = pci_device_ids,
+};
+