haswell: Add initial support for Haswell platforms
The Haswell parts use a PCH code named Lynx Point (Series 8). Therefore,
the southbridge support is included as well. The basis for this code is
the Sandybridge code. Management Engine, IRQ routing, and ACPI still requires
more attention, but this is a good starting point.
This code partially gets up through the romstage just before training
memory on a Haswell reference board.
Change-Id: If572d6c21ca051b486b82a924ca0ffe05c4d0ad4
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-on: http://review.coreboot.org/2616
Tested-by: build bot (Jenkins)
Reviewed-by: Ronald G. Minnich <rminnich@gmail.com>
diff --git a/src/southbridge/intel/Kconfig b/src/southbridge/intel/Kconfig
index bb539ad..5637c4a 100644
--- a/src/southbridge/intel/Kconfig
+++ b/src/southbridge/intel/Kconfig
@@ -12,3 +12,4 @@
source src/southbridge/intel/pxhd/Kconfig
source src/southbridge/intel/sch/Kconfig
source src/southbridge/intel/bd82x6x/Kconfig
+source src/southbridge/intel/lynxpoint/Kconfig
diff --git a/src/southbridge/intel/Makefile.inc b/src/southbridge/intel/Makefile.inc
index 75f4322..ba3b1d4 100644
--- a/src/southbridge/intel/Makefile.inc
+++ b/src/southbridge/intel/Makefile.inc
@@ -13,3 +13,4 @@
subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_SCH) += sch
subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_BD82X6X) += bd82x6x
subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_C216) += bd82x6x
+subdirs-$(CONFIG_SOUTHBRIDGE_INTEL_LYNXPOINT) += lynxpoint
diff --git a/src/southbridge/intel/lynxpoint/Kconfig b/src/southbridge/intel/lynxpoint/Kconfig
new file mode 100644
index 0000000..e1d0e35
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/Kconfig
@@ -0,0 +1,54 @@
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2011 Google Inc.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; version 2 of the License.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+config SOUTHBRIDGE_INTEL_LYNXPOINT
+ bool
+
+if SOUTHBRIDGE_INTEL_LYNXPOINT
+
+config SOUTH_BRIDGE_OPTIONS # dummy
+ def_bool y
+ select IOAPIC
+ select HAVE_HARD_RESET
+ select HAVE_USBDEBUG
+ select USE_WATCHDOG_ON_BOOT
+ select PCIEXP_ASPM
+ select PCIEXP_COMMON_CLOCK
+ select SPI_FLASH
+
+config EHCI_BAR
+ hex
+ default 0xfef00000
+
+config EHCI_DEBUG_OFFSET
+ hex
+ default 0xa0
+
+config BOOTBLOCK_SOUTHBRIDGE_INIT
+ string
+ default "southbridge/intel/lynxpoint/bootblock.c"
+
+config SERIRQ_CONTINUOUS_MODE
+ bool
+ default n
+ help
+ If you set this option to y, the serial IRQ machine will be
+ operated in continuous mode.
+
+endif
diff --git a/src/southbridge/intel/lynxpoint/Makefile.inc b/src/southbridge/intel/lynxpoint/Makefile.inc
new file mode 100644
index 0000000..d4522c3
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/Makefile.inc
@@ -0,0 +1,71 @@
+##
+## This file is part of the coreboot project.
+##
+## Copyright (C) 2010 Google Inc.
+##
+## This program is free software; you can redistribute it and/or modify
+## it under the terms of the GNU General Public License as published by
+## the Free Software Foundation; version 2 of the License.
+##
+## This program is distributed in the hope that it will be useful,
+## but WITHOUT ANY WARRANTY; without even the implied warranty of
+## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+## GNU General Public License for more details.
+##
+## You should have received a copy of the GNU General Public License
+## along with this program; if not, write to the Free Software
+## Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+##
+
+# Run an intermediate step when producing coreboot.rom
+# that adds additional components to the final firmware
+# image outside of CBFS
+# FIXME, uncomment as soon as we have ME firmware in the blobs repo
+# INTERMEDIATE:=lynxpoint_add_me
+
+ramstage-y += pch.c
+ramstage-y += azalia.c
+ramstage-y += lpc.c
+ramstage-y += pci.c
+ramstage-y += pcie.c
+ramstage-y += sata.c
+ramstage-y += usb_ehci.c
+ramstage-y += me_9.x.c
+ramstage-y += smbus.c
+
+ramstage-y += me_status.c
+ramstage-y += reset.c
+ramstage-y += watchdog.c
+ramstage-y += acpi.c
+
+ramstage-$(CONFIG_ELOG) += elog.c
+ramstage-y += spi.c
+smm-$(CONFIG_SPI_FLASH_SMM) += spi.c
+
+ramstage-$(CONFIG_HAVE_SMI_HANDLER) += smi.c
+smm-$(CONFIG_HAVE_SMI_HANDLER) += smihandler.c me_9.x.c finalize.c
+
+romstage-y += early_usb.c early_smbus.c early_me.c me_status.c gpio.c
+romstage-$(CONFIG_USBDEBUG) += usb_debug.c
+romstage-y += reset.c early_spi.c
+
+lynxpoint_add_me: $(obj)/coreboot.pre $(IFDTOOL)
+ printf " DD Adding Intel Firmware Descriptor\n"
+ dd if=3rdparty/mainboard/$(MAINBOARDDIR)/descriptor.bin \
+ of=$(obj)/coreboot.pre conv=notrunc >/dev/null 2>&1
+ printf " IFDTOOL me.bin -> coreboot.pre\n"
+ $(objutil)/ifdtool/ifdtool \
+ -i ME:3rdparty/mainboard/$(MAINBOARDDIR)/me.bin \
+ $(obj)/coreboot.pre
+ mv $(obj)/coreboot.pre.new $(obj)/coreboot.pre
+ifeq ($(CONFIG_LOCK_MANAGEMENT_ENGINE),y)
+ printf " IFDTOOL Locking Management Engine\n"
+ $(objutil)/ifdtool/ifdtool -l $(obj)/coreboot.pre
+ mv $(obj)/coreboot.pre.new $(obj)/coreboot.pre
+else
+ printf " IFDTOOL Unlocking Management Engine\n"
+ $(objutil)/ifdtool/ifdtool -u $(obj)/coreboot.pre
+ mv $(obj)/coreboot.pre.new $(obj)/coreboot.pre
+endif
+
+PHONY += lynxpoint_add_me
diff --git a/src/southbridge/intel/lynxpoint/acpi.c b/src/southbridge/intel/lynxpoint/acpi.c
new file mode 100644
index 0000000..4118b9d
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi.c
@@ -0,0 +1,55 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ * Copyright (C) 2012 Chromium OS Authors
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <types.h>
+#include <string.h>
+#include "pch.h"
+
+void acpi_create_intel_hpet(acpi_hpet_t * hpet)
+{
+ acpi_header_t *header = &(hpet->header);
+ acpi_addr_t *addr = &(hpet->addr);
+
+ memset((void *) hpet, 0, sizeof(acpi_hpet_t));
+
+ /* fill out header fields */
+ memcpy(header->signature, "HPET", 4);
+ memcpy(header->oem_id, OEM_ID, 6);
+ memcpy(header->oem_table_id, ACPI_TABLE_CREATOR, 8);
+ memcpy(header->asl_compiler_id, ASLC, 4);
+
+ header->length = sizeof(acpi_hpet_t);
+ header->revision = 1;
+
+ /* fill out HPET address */
+ addr->space_id = 0; /* Memory */
+ addr->bit_width = 64;
+ addr->bit_offset = 0;
+ addr->addrl = (unsigned long long)HPET_ADDR & 0xffffffff;
+ addr->addrh = (unsigned long long)HPET_ADDR >> 32;
+
+ hpet->id = 0x8086a201; /* Intel */
+ hpet->number = 0x00;
+ hpet->min_tick = 0x0080;
+
+ header->checksum =
+ acpi_checksum((void *) hpet, sizeof(acpi_hpet_t));
+}
+
diff --git a/src/southbridge/intel/lynxpoint/acpi/audio.asl b/src/southbridge/intel/lynxpoint/acpi/audio.asl
new file mode 100644
index 0000000..a455328
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/audio.asl
@@ -0,0 +1,36 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/* Intel PCH HDA */
+
+// Intel High Definition Audio (Azalia) 0:1b.0
+
+Device (HDEF)
+{
+ Name (_ADR, 0x001b0000)
+
+ // Power Resources for Wake
+ Name (_PRW, Package(){
+ 13, // Bit 13 of GPE
+ 4 // Can wake from S4 state.
+ })
+}
+
diff --git a/src/southbridge/intel/lynxpoint/acpi/globalnvs.asl b/src/southbridge/intel/lynxpoint/acpi/globalnvs.asl
new file mode 100644
index 0000000..2fe092d
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/globalnvs.asl
@@ -0,0 +1,287 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ * Copyright (C) 2012 The Chromium OS Authors
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/* Global Variables */
+
+Name(\PICM, 0) // IOAPIC/8259
+Name(\DSEN, 1) // Display Output Switching Enable
+
+/* Global ACPI memory region. This region is used for passing information
+ * between coreboot (aka "the system bios"), ACPI, and the SMI handler.
+ * Since we don't know where this will end up in memory at ACPI compile time,
+ * we have to fix it up in coreboot's ACPI creation phase.
+ */
+
+
+OperationRegion (GNVS, SystemMemory, 0xC0DEBABE, 0xf00)
+Field (GNVS, ByteAcc, NoLock, Preserve)
+{
+ /* Miscellaneous */
+ Offset (0x00),
+ OSYS, 16, // 0x00 - Operating System
+ SMIF, 8, // 0x02 - SMI function
+ PRM0, 8, // 0x03 - SMI function parameter
+ PRM1, 8, // 0x04 - SMI function parameter
+ SCIF, 8, // 0x05 - SCI function
+ PRM2, 8, // 0x06 - SCI function parameter
+ PRM3, 8, // 0x07 - SCI function parameter
+ LCKF, 8, // 0x08 - Global Lock function for EC
+ PRM4, 8, // 0x09 - Lock function parameter
+ PRM5, 8, // 0x0a - Lock function parameter
+ P80D, 32, // 0x0b - Debug port (IO 0x80) value
+ LIDS, 8, // 0x0f - LID state (open = 1)
+ PWRS, 8, // 0x10 - Power State (AC = 1)
+ /* Thermal policy */
+ Offset (0x11),
+ TLVL, 8, // 0x11 - Throttle Level Limit
+ FLVL, 8, // 0x12 - Current FAN Level
+ TCRT, 8, // 0x13 - Critical Threshold
+ TPSV, 8, // 0x14 - Passive Threshold
+ TMAX, 8, // 0x15 - CPU Tj_max
+ F0OF, 8, // 0x16 - FAN 0 OFF Threshold
+ F0ON, 8, // 0x17 - FAN 0 ON Threshold
+ F0PW, 8, // 0x18 - FAN 0 PWM value
+ F1OF, 8, // 0x19 - FAN 1 OFF Threshold
+ F1ON, 8, // 0x1a - FAN 1 ON Threshold
+ F1PW, 8, // 0x1b - FAN 1 PWM value
+ F2OF, 8, // 0x1c - FAN 2 OFF Threshold
+ F2ON, 8, // 0x1d - FAN 2 ON Threshold
+ F2PW, 8, // 0x1e - FAN 2 PWM value
+ F3OF, 8, // 0x1f - FAN 3 OFF Threshold
+ F3ON, 8, // 0x20 - FAN 3 ON Threshold
+ F3PW, 8, // 0x21 - FAN 3 PWM value
+ F4OF, 8, // 0x22 - FAN 4 OFF Threshold
+ F4ON, 8, // 0x23 - FAN 4 ON Threshold
+ F4PW, 8, // 0x24 - FAN 4 PWM value
+ TMPS, 8, // 0x25 - Temperature Sensor ID
+ /* Processor Identification */
+ Offset (0x28),
+ APIC, 8, // 0x28 - APIC Enabled by coreboot
+ MPEN, 8, // 0x29 - Multi Processor Enable
+ PCP0, 8, // 0x2a - PDC CPU/CORE 0
+ PCP1, 8, // 0x2b - PDC CPU/CORE 1
+ PPCM, 8, // 0x2c - Max. PPC state
+ PCNT, 8, // 0x2d - Processor count
+ /* Super I/O & CMOS config */
+ Offset (0x32),
+ NATP, 8, // 0x32 -
+ S5U0, 8, // 0x33 - Enable USB0 in S5
+ S5U1, 8, // 0x34 - Enable USB1 in S5
+ S3U0, 8, // 0x35 - Enable USB0 in S3
+ S3U1, 8, // 0x36 - Enable USB1 in S3
+ S33G, 8, // 0x37 - Enable 3G in S3
+ CMEM, 32, // 0x38 - CBMEM TOC
+ /* Integrated Graphics Device */
+ Offset (0x3c),
+ IGDS, 8, // 0x3c - IGD state (primary = 1)
+ TLST, 8, // 0x3d - Display Toggle List pointer
+ CADL, 8, // 0x3e - Currently Attached Devices List
+ PADL, 8, // 0x3f - Previously Attached Devices List
+ CSTE, 16, // 0x40 - Current display state
+ NSTE, 16, // 0x42 - Next display state
+ SSTE, 16, // 0x44 - Set display state
+ Offset (0x46),
+ NDID, 8, // 0x46 - Number of Device IDs
+ DID1, 32, // 0x47 - Device ID 1
+ DID2, 32, // 0x4b - Device ID 2
+ DID3, 32, // 0x4f - Device ID 3
+ DID4, 32, // 0x53 - Device ID 4
+ DID5, 32, // 0x57 - Device ID 5
+ /* Backlight Control */
+ Offset (0x64),
+ BLCS, 8, // 0x64 - Backlight control possible?
+ BRTL, 8, // 0x65 - Brightness Level
+ ODDS, 8, // 0x66
+ /* Ambient Light Sensors */
+ Offset (0x6e),
+ ALSE, 8, // 0x6e - ALS enable
+ ALAF, 8, // 0x6f - Ambient light adjustment factor
+ LLOW, 8, // 0x70 - LUX Low
+ LHIH, 8, // 0x71 - LUX High
+ /* EMA */
+ Offset (0x78),
+ EMAE, 8, // 0x78 - EMA enable
+ EMAP, 16, // 0x79 - EMA pointer
+ EMAL, 16, // 0x7b - EMA length
+ /* MEF */
+ Offset (0x82),
+ MEFE, 8, // 0x82 - MEF enable
+ /* TPM support */
+ Offset (0x8c),
+ TPMP, 8, // 0x8c - TPM
+ TPME, 8, // 0x8d - TPM enable
+ /* SATA */
+ Offset (0x96),
+ GTF0, 56, // 0x96 - GTF task file buffer for port 0
+ GTF1, 56, // 0x9d - GTF task file buffer for port 1
+ GTF2, 56, // 0xa4 - GTF task file buffer for port 2
+ IDEM, 8, // 0xab - IDE mode (compatible / enhanced)
+ IDET, 8, // 0xac - IDE
+ /* IGD OpRegion */
+ Offset (0xb4),
+ ASLB, 32, // 0xb4 - IGD OpRegion Base Address
+ IBTT, 8, // 0xb8 - IGD boot panel device
+ IPAT, 8, // 0xb9 - IGD panel type cmos option
+ ITVF, 8, // 0xba - IGD TV format cmos option
+ ITVM, 8, // 0xbb - IGD TV minor format option
+ IPSC, 8, // 0xbc - IGD panel scaling
+ IBLC, 8, // 0xbd - IGD BLC config
+ IBIA, 8, // 0xbe - IGD BIA config
+ ISSC, 8, // 0xbf - IGD SSC config
+ I409, 8, // 0xc0 - IGD 0409 modified settings
+ I509, 8, // 0xc1 - IGD 0509 modified settings
+ I609, 8, // 0xc2 - IGD 0609 modified settings
+ I709, 8, // 0xc3 - IGD 0709 modified settings
+ IDMM, 8, // 0xc4 - IGD Power conservation feature
+ IDMS, 8, // 0xc5 - IGD DVMT memory size
+ IF1E, 8, // 0xc6 - IGD function 1 enable
+ HVCO, 8, // 0xc7 - IGD HPLL VCO
+ NXD1, 32, // 0xc8 - IGD _DGS next DID1
+ NXD2, 32, // 0xcc - IGD _DGS next DID2
+ NXD3, 32, // 0xd0 - IGD _DGS next DID3
+ NXD4, 32, // 0xd4 - IGD _DGS next DID4
+ NXD5, 32, // 0xd8 - IGD _DGS next DID5
+ NXD6, 32, // 0xdc - IGD _DGS next DID6
+ NXD7, 32, // 0xe0 - IGD _DGS next DID7
+ NXD8, 32, // 0xe4 - IGD _DGS next DID8
+
+ ISCI, 8, // 0xe8 - IGD SMI/SCI mode (0: SCI)
+ PAVP, 8, // 0xe9 - IGD PAVP data
+ Offset (0xeb),
+ OSCC, 8, // 0xeb - PCIe OSC control
+ NPCE, 8, // 0xec - native pcie support
+ PLFL, 8, // 0xed - platform flavor
+ BREV, 8, // 0xee - board revision
+ DPBM, 8, // 0xef - digital port b mode
+ DPCM, 8, // 0xf0 - digital port c mode
+ DPDM, 8, // 0xf1 - digital port d mode
+ ALFP, 8, // 0xf2 - active lfp
+ IMON, 8, // 0xf3 - current graphics turbo imon value
+ MMIO, 8, // 0xf4 - 64bit mmio support
+
+ /* ChromeOS specific */
+ Offset (0x100),
+ #include <vendorcode/google/chromeos/acpi/gnvs.asl>
+}
+
+/* Set flag to enable USB charging in S3 */
+Method (S3UE)
+{
+ Store (One, \S3U0)
+ Store (One, \S3U1)
+}
+
+/* Set flag to disable USB charging in S3 */
+Method (S3UD)
+{
+ Store (Zero, \S3U0)
+ Store (Zero, \S3U1)
+}
+
+/* Set flag to enable USB charging in S5 */
+Method (S5UE)
+{
+ Store (One, \S5U0)
+ Store (One, \S5U1)
+}
+
+/* Set flag to disable USB charging in S5 */
+Method (S5UD)
+{
+ Store (Zero, \S5U0)
+ Store (Zero, \S5U1)
+}
+
+/* Set flag to enable 3G module in S3 */
+Method (S3GE)
+{
+ Store (One, \S33G)
+}
+
+/* Set flag to disable 3G module in S3 */
+Method (S3GD)
+{
+ Store (Zero, \S33G)
+}
+
+External (\_TZ.THRM)
+External (\_TZ.SKIN)
+
+Method (TZUP)
+{
+ /* Update Primary Thermal Zone */
+ If (CondRefOf (\_TZ.THRM, Local0)) {
+ Notify (\_TZ.THRM, 0x81)
+ }
+
+ /* Update Secondary Thermal Zone */
+ If (CondRefOf (\_TZ.SKIN, Local0)) {
+ Notify (\_TZ.SKIN, 0x81)
+ }
+}
+
+/* Update Fan 0 thresholds */
+Method (F0UT, 2)
+{
+ Store (Arg0, \F0OF)
+ Store (Arg1, \F0ON)
+ TZUP ()
+}
+
+/* Update Fan 1 thresholds */
+Method (F1UT, 2)
+{
+ Store (Arg0, \F1OF)
+ Store (Arg1, \F1ON)
+ TZUP ()
+}
+
+/* Update Fan 2 thresholds */
+Method (F2UT, 2)
+{
+ Store (Arg0, \F2OF)
+ Store (Arg1, \F2ON)
+ TZUP ()
+}
+
+/* Update Fan 3 thresholds */
+Method (F3UT, 2)
+{
+ Store (Arg0, \F3OF)
+ Store (Arg1, \F3ON)
+ TZUP ()
+}
+
+/* Update Fan 4 thresholds */
+Method (F4UT, 2)
+{
+ Store (Arg0, \F4OF)
+ Store (Arg1, \F4ON)
+ TZUP ()
+}
+
+/* Update Temperature Sensor ID */
+Method (TMPU, 1)
+{
+ Store (Arg0, \TMPS)
+ TZUP ()
+}
diff --git a/src/southbridge/intel/lynxpoint/acpi/irqlinks.asl b/src/southbridge/intel/lynxpoint/acpi/irqlinks.asl
new file mode 100644
index 0000000..5fcee45
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/irqlinks.asl
@@ -0,0 +1,493 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+Device (LNKA)
+{
+ Name (_HID, EISAID("PNP0C0F"))
+ Name (_UID, 1)
+
+ // Disable method
+ Method (_DIS, 0, Serialized)
+ {
+ Store (0x80, PRTA)
+ }
+
+ // Possible Resource Settings for this Link
+ Name (_PRS, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared)
+ { 1, 3, 4, 5, 6, 7, 10, 12, 14, 15 }
+ })
+
+ // Current Resource Settings for this link
+ Method (_CRS, 0, Serialized)
+ {
+ Name (RTLA, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared) {}
+ })
+ CreateWordField(RTLA, 1, IRQ0)
+
+ // Clear the WordField
+ Store (Zero, IRQ0)
+
+ // Set the bit from PRTA
+ ShiftLeft(1, And(PRTA, 0x0f), IRQ0)
+
+ Return (RTLA)
+ }
+
+ // Set Resource Setting for this IRQ link
+ Method (_SRS, 1, Serialized)
+ {
+ CreateWordField(Arg0, 1, IRQ0)
+
+ // Which bit is set?
+ FindSetRightBit(IRQ0, Local0)
+
+ Decrement(Local0)
+ Store(Local0, PRTA)
+ }
+
+ // Status
+ Method (_STA, 0, Serialized)
+ {
+ If(And(PRTA, 0x80)) {
+ Return (0x9)
+ } Else {
+ Return (0xb)
+ }
+ }
+}
+
+Device (LNKB)
+{
+ Name (_HID, EISAID("PNP0C0F"))
+ Name (_UID, 2)
+
+ // Disable method
+ Method (_DIS, 0, Serialized)
+ {
+ Store (0x80, PRTB)
+ }
+
+ // Possible Resource Settings for this Link
+ Name (_PRS, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared)
+ { 1, 3, 4, 5, 6, 7, 11, 12, 14, 15 }
+ })
+
+ // Current Resource Settings for this link
+ Method (_CRS, 0, Serialized)
+ {
+ Name (RTLB, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared) {}
+ })
+ CreateWordField(RTLB, 1, IRQ0)
+
+ // Clear the WordField
+ Store (Zero, IRQ0)
+
+ // Set the bit from PRTB
+ ShiftLeft(1, And(PRTB, 0x0f), IRQ0)
+
+ Return (RTLB)
+ }
+
+ // Set Resource Setting for this IRQ link
+ Method (_SRS, 1, Serialized)
+ {
+ CreateWordField(Arg0, 1, IRQ0)
+
+ // Which bit is set?
+ FindSetRightBit(IRQ0, Local0)
+
+ Decrement(Local0)
+ Store(Local0, PRTB)
+ }
+
+ // Status
+ Method (_STA, 0, Serialized)
+ {
+ If(And(PRTB, 0x80)) {
+ Return (0x9)
+ } Else {
+ Return (0xb)
+ }
+ }
+}
+
+Device (LNKC)
+{
+ Name (_HID, EISAID("PNP0C0F"))
+ Name (_UID, 3)
+
+ // Disable method
+ Method (_DIS, 0, Serialized)
+ {
+ Store (0x80, PRTC)
+ }
+
+ // Possible Resource Settings for this Link
+ Name (_PRS, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared)
+ { 1, 3, 4, 5, 6, 7, 10, 12, 14, 15 }
+ })
+
+ // Current Resource Settings for this link
+ Method (_CRS, 0, Serialized)
+ {
+ Name (RTLC, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared) {}
+ })
+ CreateWordField(RTLC, 1, IRQ0)
+
+ // Clear the WordField
+ Store (Zero, IRQ0)
+
+ // Set the bit from PRTC
+ ShiftLeft(1, And(PRTC, 0x0f), IRQ0)
+
+ Return (RTLC)
+ }
+
+ // Set Resource Setting for this IRQ link
+ Method (_SRS, 1, Serialized)
+ {
+ CreateWordField(Arg0, 1, IRQ0)
+
+ // Which bit is set?
+ FindSetRightBit(IRQ0, Local0)
+
+ Decrement(Local0)
+ Store(Local0, PRTC)
+ }
+
+ // Status
+ Method (_STA, 0, Serialized)
+ {
+ If(And(PRTC, 0x80)) {
+ Return (0x9)
+ } Else {
+ Return (0xb)
+ }
+ }
+}
+
+Device (LNKD)
+{
+ Name (_HID, EISAID("PNP0C0F"))
+ Name (_UID, 4)
+
+ // Disable method
+ Method (_DIS, 0, Serialized)
+ {
+ Store (0x80, PRTD)
+ }
+
+ // Possible Resource Settings for this Link
+ Name (_PRS, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared)
+ { 1, 3, 4, 5, 6, 7, 11, 12, 14, 15 }
+ })
+
+ // Current Resource Settings for this link
+ Method (_CRS, 0, Serialized)
+ {
+ Name (RTLD, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared) {}
+ })
+ CreateWordField(RTLD, 1, IRQ0)
+
+ // Clear the WordField
+ Store (Zero, IRQ0)
+
+ // Set the bit from PRTD
+ ShiftLeft(1, And(PRTD, 0x0f), IRQ0)
+
+ Return (RTLD)
+ }
+
+ // Set Resource Setting for this IRQ link
+ Method (_SRS, 1, Serialized)
+ {
+ CreateWordField(Arg0, 1, IRQ0)
+
+ // Which bit is set?
+ FindSetRightBit(IRQ0, Local0)
+
+ Decrement(Local0)
+ Store(Local0, PRTD)
+ }
+
+ // Status
+ Method (_STA, 0, Serialized)
+ {
+ If(And(PRTD, 0x80)) {
+ Return (0x9)
+ } Else {
+ Return (0xb)
+ }
+ }
+}
+
+Device (LNKE)
+{
+ Name (_HID, EISAID("PNP0C0F"))
+ Name (_UID, 5)
+
+ // Disable method
+ Method (_DIS, 0, Serialized)
+ {
+ Store (0x80, PRTE)
+ }
+
+ // Possible Resource Settings for this Link
+ Name (_PRS, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared)
+ { 1, 3, 4, 5, 6, 7, 10, 12, 14, 15 }
+ })
+
+ // Current Resource Settings for this link
+ Method (_CRS, 0, Serialized)
+ {
+ Name (RTLE, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared) {}
+ })
+ CreateWordField(RTLE, 1, IRQ0)
+
+ // Clear the WordField
+ Store (Zero, IRQ0)
+
+ // Set the bit from PRTE
+ ShiftLeft(1, And(PRTE, 0x0f), IRQ0)
+
+ Return (RTLE)
+ }
+
+ // Set Resource Setting for this IRQ link
+ Method (_SRS, 1, Serialized)
+ {
+ CreateWordField(Arg0, 1, IRQ0)
+
+ // Which bit is set?
+ FindSetRightBit(IRQ0, Local0)
+
+ Decrement(Local0)
+ Store(Local0, PRTE)
+ }
+
+ // Status
+ Method (_STA, 0, Serialized)
+ {
+ If(And(PRTE, 0x80)) {
+ Return (0x9)
+ } Else {
+ Return (0xb)
+ }
+ }
+}
+
+Device (LNKF)
+{
+ Name (_HID, EISAID("PNP0C0F"))
+ Name (_UID, 6)
+
+ // Disable method
+ Method (_DIS, 0, Serialized)
+ {
+ Store (0x80, PRTF)
+ }
+
+ // Possible Resource Settings for this Link
+ Name (_PRS, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared)
+ { 1, 3, 4, 5, 6, 7, 11, 12, 14, 15 }
+ })
+
+ // Current Resource Settings for this link
+ Method (_CRS, 0, Serialized)
+ {
+ Name (RTLF, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared) {}
+ })
+ CreateWordField(RTLF, 1, IRQ0)
+
+ // Clear the WordField
+ Store (Zero, IRQ0)
+
+ // Set the bit from PRTF
+ ShiftLeft(1, And(PRTF, 0x0f), IRQ0)
+
+ Return (RTLF)
+ }
+
+ // Set Resource Setting for this IRQ link
+ Method (_SRS, 1, Serialized)
+ {
+ CreateWordField(Arg0, 1, IRQ0)
+
+ // Which bit is set?
+ FindSetRightBit(IRQ0, Local0)
+
+ Decrement(Local0)
+ Store(Local0, PRTF)
+ }
+
+ // Status
+ Method (_STA, 0, Serialized)
+ {
+ If(And(PRTF, 0x80)) {
+ Return (0x9)
+ } Else {
+ Return (0xb)
+ }
+ }
+}
+
+Device (LNKG)
+{
+ Name (_HID, EISAID("PNP0C0F"))
+ Name (_UID, 7)
+
+ // Disable method
+ Method (_DIS, 0, Serialized)
+ {
+ Store (0x80, PRTG)
+ }
+
+ // Possible Resource Settings for this Link
+ Name (_PRS, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared)
+ { 1, 3, 4, 5, 6, 7, 10, 12, 14, 15 }
+ })
+
+ // Current Resource Settings for this link
+ Method (_CRS, 0, Serialized)
+ {
+ Name (RTLG, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared) {}
+ })
+ CreateWordField(RTLG, 1, IRQ0)
+
+ // Clear the WordField
+ Store (Zero, IRQ0)
+
+ // Set the bit from PRTG
+ ShiftLeft(1, And(PRTG, 0x0f), IRQ0)
+
+ Return (RTLG)
+ }
+
+ // Set Resource Setting for this IRQ link
+ Method (_SRS, 1, Serialized)
+ {
+ CreateWordField(Arg0, 1, IRQ0)
+
+ // Which bit is set?
+ FindSetRightBit(IRQ0, Local0)
+
+ Decrement(Local0)
+ Store(Local0, PRTG)
+ }
+
+ // Status
+ Method (_STA, 0, Serialized)
+ {
+ If(And(PRTG, 0x80)) {
+ Return (0x9)
+ } Else {
+ Return (0xb)
+ }
+ }
+}
+
+Device (LNKH)
+{
+ Name (_HID, EISAID("PNP0C0F"))
+ Name (_UID, 8)
+
+ // Disable method
+ Method (_DIS, 0, Serialized)
+ {
+ Store (0x80, PRTH)
+ }
+
+ // Possible Resource Settings for this Link
+ Name (_PRS, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared)
+ { 1, 3, 4, 5, 6, 7, 11, 12, 14, 15 }
+ })
+
+ // Current Resource Settings for this link
+ Method (_CRS, 0, Serialized)
+ {
+ Name (RTLH, ResourceTemplate()
+ {
+ IRQ(Level, ActiveLow, Shared) {}
+ })
+ CreateWordField(RTLH, 1, IRQ0)
+
+ // Clear the WordField
+ Store (Zero, IRQ0)
+
+ // Set the bit from PRTH
+ ShiftLeft(1, And(PRTH, 0x0f), IRQ0)
+
+ Return (RTLH)
+ }
+
+ // Set Resource Setting for this IRQ link
+ Method (_SRS, 1, Serialized)
+ {
+ CreateWordField(Arg0, 1, IRQ0)
+
+ // Which bit is set?
+ FindSetRightBit(IRQ0, Local0)
+
+ Decrement(Local0)
+ Store(Local0, PRTH)
+ }
+
+ // Status
+ Method (_STA, 0, Serialized)
+ {
+ If(And(PRTH, 0x80)) {
+ Return (0x9)
+ } Else {
+ Return (0xb)
+ }
+ }
+}
+
diff --git a/src/southbridge/intel/lynxpoint/acpi/lpc.asl b/src/southbridge/intel/lynxpoint/acpi/lpc.asl
new file mode 100644
index 0000000..cc59850
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/lpc.asl
@@ -0,0 +1,248 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+// Intel LPC Bus Device - 0:1f.0
+
+Device (LPCB)
+{
+ Name(_ADR, 0x001f0000)
+
+ OperationRegion(LPC0, PCI_Config, 0x00, 0x100)
+ Field (LPC0, AnyAcc, NoLock, Preserve)
+ {
+ Offset (0x40),
+ PMBS, 16, // PMBASE
+ Offset (0x60), // Interrupt Routing Registers
+ PRTA, 8,
+ PRTB, 8,
+ PRTC, 8,
+ PRTD, 8,
+ Offset (0x68),
+ PRTE, 8,
+ PRTF, 8,
+ PRTG, 8,
+ PRTH, 8,
+
+ Offset (0x80), // IO Decode Ranges
+ IOD0, 8,
+ IOD1, 8,
+
+ Offset (0xb8), // GPIO Routing Control
+ GR00, 2,
+ GR01, 2,
+ GR02, 2,
+ GR03, 2,
+ GR04, 2,
+ GR05, 2,
+ GR06, 2,
+ GR07, 2,
+ GR08, 2,
+ GR09, 2,
+ GR10, 2,
+ GR11, 2,
+ GR12, 2,
+ GR13, 2,
+ GR14, 2,
+ GR15, 2,
+
+ Offset (0xf0), // RCBA
+ RCEN, 1,
+ , 13,
+ RCBA, 18,
+ }
+
+ #include "irqlinks.asl"
+
+ #include "acpi/ec.asl"
+
+ Device (DMAC) // DMA Controller
+ {
+ Name(_HID, EISAID("PNP0200"))
+ Name(_CRS, ResourceTemplate()
+ {
+ IO (Decode16, 0x00, 0x00, 0x01, 0x20)
+ IO (Decode16, 0x81, 0x81, 0x01, 0x11)
+ IO (Decode16, 0x93, 0x93, 0x01, 0x0d)
+ IO (Decode16, 0xc0, 0xc0, 0x01, 0x20)
+ DMA (Compatibility, NotBusMaster, Transfer8_16) { 4 }
+ })
+ }
+
+ Device (FWH) // Firmware Hub
+ {
+ Name (_HID, EISAID("INT0800"))
+ Name (_CRS, ResourceTemplate()
+ {
+ Memory32Fixed(ReadOnly, 0xff000000, 0x01000000)
+ })
+ }
+
+ Device (HPET)
+ {
+ Name (_HID, EISAID("PNP0103"))
+ Name (_CID, 0x010CD041)
+
+ Name(BUF0, ResourceTemplate()
+ {
+ Memory32Fixed(ReadOnly, 0xfed00000, 0x400, FED0)
+ })
+
+ Method (_STA, 0) // Device Status
+ {
+ If (HPTE) {
+ // Note: Ancient versions of Windows don't want
+ // to see the HPET in order to work right
+ If (LGreaterEqual(OSYS, 2001)) {
+ Return (0xf) // Enable and show device
+ } Else {
+ Return (0xb) // Enable and don't show device
+ }
+ }
+
+ Return (0x0) // Not enabled, don't show.
+ }
+
+ Method (_CRS, 0, Serialized) // Current resources
+ {
+ If (HPTE) {
+ CreateDWordField(BUF0, \_SB.PCI0.LPCB.HPET.FED0._BAS, HPT0)
+ If (Lequal(HPAS, 1)) {
+ Store(0xfed01000, HPT0)
+ }
+
+ If (Lequal(HPAS, 2)) {
+ Store(0xfed02000, HPT0)
+ }
+
+ If (Lequal(HPAS, 3)) {
+ Store(0xfed03000, HPT0)
+ }
+ }
+
+ Return (BUF0)
+ }
+ }
+
+ Device(PIC) // 8259 Interrupt Controller
+ {
+ Name(_HID,EISAID("PNP0000"))
+ Name(_CRS, ResourceTemplate()
+ {
+ IO (Decode16, 0x20, 0x20, 0x01, 0x02)
+ IO (Decode16, 0x24, 0x24, 0x01, 0x02)
+ IO (Decode16, 0x28, 0x28, 0x01, 0x02)
+ IO (Decode16, 0x2c, 0x2c, 0x01, 0x02)
+ IO (Decode16, 0x30, 0x30, 0x01, 0x02)
+ IO (Decode16, 0x34, 0x34, 0x01, 0x02)
+ IO (Decode16, 0x38, 0x38, 0x01, 0x02)
+ IO (Decode16, 0x3c, 0x3c, 0x01, 0x02)
+ IO (Decode16, 0xa0, 0xa0, 0x01, 0x02)
+ IO (Decode16, 0xa4, 0xa4, 0x01, 0x02)
+ IO (Decode16, 0xa8, 0xa8, 0x01, 0x02)
+ IO (Decode16, 0xac, 0xac, 0x01, 0x02)
+ IO (Decode16, 0xb0, 0xb0, 0x01, 0x02)
+ IO (Decode16, 0xb4, 0xb4, 0x01, 0x02)
+ IO (Decode16, 0xb8, 0xb8, 0x01, 0x02)
+ IO (Decode16, 0xbc, 0xbc, 0x01, 0x02)
+ IO (Decode16, 0x4d0, 0x4d0, 0x01, 0x02)
+ IRQNoFlags () { 2 }
+ })
+ }
+
+ Device(MATH) // FPU
+ {
+ Name (_HID, EISAID("PNP0C04"))
+ Name (_CRS, ResourceTemplate()
+ {
+ IO (Decode16, 0xf0, 0xf0, 0x01, 0x01)
+ IRQNoFlags() { 13 }
+ })
+ }
+
+ Device(LDRC) // LPC device: Resource consumption
+ {
+ Name (_HID, EISAID("PNP0C02"))
+ Name (_UID, 2)
+ Name (_CRS, ResourceTemplate()
+ {
+ IO (Decode16, 0x2e, 0x2e, 0x1, 0x02) // First SuperIO
+ IO (Decode16, 0x4e, 0x4e, 0x1, 0x02) // Second SuperIO
+ IO (Decode16, 0x61, 0x61, 0x1, 0x01) // NMI Status
+ IO (Decode16, 0x63, 0x63, 0x1, 0x01) // CPU Reserved
+ IO (Decode16, 0x65, 0x65, 0x1, 0x01) // CPU Reserved
+ IO (Decode16, 0x67, 0x67, 0x1, 0x01) // CPU Reserved
+ IO (Decode16, 0x80, 0x80, 0x1, 0x01) // Port 80 Post
+ IO (Decode16, 0x92, 0x92, 0x1, 0x01) // CPU Reserved
+ IO (Decode16, 0xb2, 0xb2, 0x1, 0x02) // SWSMI
+ //IO (Decode16, 0x800, 0x800, 0x1, 0x10) // ACPI I/O trap
+ IO (Decode16, DEFAULT_PMBASE, DEFAULT_PMBASE, 0x1, 0x80) // ICH7-M ACPI
+ IO (Decode16, DEFAULT_GPIOBASE, DEFAULT_GPIOBASE, 0x1, 0x40) // ICH7-M GPIO
+ })
+ }
+
+ Device (RTC) // Real Time Clock
+ {
+ Name (_HID, EISAID("PNP0B00"))
+ Name (_CRS, ResourceTemplate()
+ {
+ IO (Decode16, 0x70, 0x70, 1, 8)
+// Disable as Windows doesn't like it, and systems don't seem to use it.
+// IRQNoFlags() { 8 }
+ })
+ }
+
+ Device (TIMR) // Intel 8254 timer
+ {
+ Name(_HID, EISAID("PNP0100"))
+ Name(_CRS, ResourceTemplate()
+ {
+ IO (Decode16, 0x40, 0x40, 0x01, 0x04)
+ IO (Decode16, 0x50, 0x50, 0x10, 0x04)
+ IRQNoFlags() {0}
+ })
+ }
+
+ #include "acpi/superio.asl"
+
+#ifdef ENABLE_TPM
+ Device (TPM) // Trusted Platform Module
+ {
+ Name(_HID, EISAID("IFX0102"))
+ Name(_CID, 0x310cd041)
+ Name(_UID, 1)
+
+ Method(_STA, 0)
+ {
+ If (TPMP) {
+ Return (0xf)
+ }
+ Return (0x0)
+ }
+
+ Name(_CRS, ResourceTemplate() {
+ IO (Decode16, 0x2e, 0x2e, 0x01, 0x02)
+ IO (Decode16, 0x6f0, 0x6f0, 0x01, 0x10)
+ Memory32Fixed (ReadWrite, 0xfed40000, 0x5000)
+ IRQ (Edge, Activehigh, Exclusive) { 6 }
+ })
+ }
+#endif
+}
diff --git a/src/southbridge/intel/lynxpoint/acpi/pch.asl b/src/southbridge/intel/lynxpoint/acpi/pch.asl
new file mode 100644
index 0000000..8632ad8
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/pch.asl
@@ -0,0 +1,275 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/* Intel Cougar Point PCH support */
+
+Scope(\)
+{
+ // IO-Trap at 0x800. This is the ACPI->SMI communication interface.
+
+ OperationRegion(IO_T, SystemIO, 0x800, 0x10)
+ Field(IO_T, ByteAcc, NoLock, Preserve)
+ {
+ Offset(0x8),
+ TRP0, 8 // IO-Trap at 0x808
+ }
+
+ // PCH Power Management Registers, located at PMBASE (0x1f.0 0x40.l)
+ OperationRegion(PMIO, SystemIO, DEFAULT_PMBASE, 0x80)
+ Field(PMIO, ByteAcc, NoLock, Preserve)
+ {
+ Offset(0x20), // GPE0_STS
+ , 16,
+ GS00, 1, // GPIO00 SCI/Wake Status
+ GS01, 1, // GPIO01 SCI/Wake Status
+ GS02, 1, // GPIO02 SCI/Wake Status
+ GS03, 1, // GPIO03 SCI/Wake Status
+ GS04, 1, // GPIO04 SCI/Wake Status
+ GS05, 1, // GPIO05 SCI/Wake Status
+ GS06, 1, // GPIO06 SCI/Wake Status
+ GS07, 1, // GPIO07 SCI/Wake Status
+ GS08, 1, // GPIO08 SCI/Wake Status
+ GS09, 1, // GPIO09 SCI/Wake Status
+ GS10, 1, // GPIO10 SCI/Wake Status
+ GS11, 1, // GPIO11 SCI/Wake Status
+ GS12, 1, // GPIO12 SCI/Wake Status
+ GS13, 1, // GPIO13 SCI/Wake Status
+ GS14, 1, // GPIO14 SCI/Wake Status
+ GS15, 1, // GPIO15 SCI/Wake Status
+ Offset(0x28), // GPE0_EN
+ , 16,
+ GE00, 1, // GPIO00 SCI/Wake Enable
+ GE01, 1, // GPIO01 SCI/Wake Enable
+ GE02, 1, // GPIO02 SCI/Wake Enable
+ GE03, 1, // GPIO03 SCI/Wake Enable
+ GE04, 1, // GPIO04 SCI/Wake Enable
+ GE05, 1, // GPIO05 SCI/Wake Enable
+ GE06, 1, // GPIO06 SCI/Wake Enable
+ GE07, 1, // GPIO07 SCI/Wake Enable
+ GE08, 1, // GPIO08 SCI/Wake Enable
+ GE09, 1, // GPIO09 SCI/Wake Enable
+ GE10, 1, // GPIO10 SCI/Wake Enable
+ GE11, 1, // GPIO11 SCI/Wake Enable
+ GE12, 1, // GPIO12 SCI/Wake Enable
+ GE13, 1, // GPIO13 SCI/Wake Enable
+ GE14, 1, // GPIO14 SCI/Wake Enable
+ GE15, 1, // GPIO15 SCI/Wake Enable
+ Offset(0x42), // General Purpose Control
+ , 1, // skip 1 bit
+ GPEC, 1, // SWGPE_CTRL
+ }
+
+ // GPIO IO mapped registers (0x1f.0 reg 0x48.l)
+ OperationRegion(GPIO, SystemIO, DEFAULT_GPIOBASE, 0x6c)
+ Field(GPIO, ByteAcc, NoLock, Preserve)
+ {
+ Offset(0x00), // GPIO Use Select
+ GU00, 8,
+ GU01, 8,
+ GU02, 8,
+ GU03, 8,
+ Offset(0x04), // GPIO IO Select
+ GIO0, 8,
+ GIO1, 8,
+ GIO2, 8,
+ GIO3, 8,
+ Offset(0x0c), // GPIO Level
+ GL00, 1,
+ GP01, 1,
+ GP02, 1,
+ GP0e, 1,
+ GP04, 1,
+ GP05, 1,
+ GP06, 1,
+ GP07, 1,
+ GP08, 1,
+ GP09, 1,
+ GP10, 1,
+ GP11, 1,
+ GP12, 1,
+ GP13, 1,
+ GP14, 1,
+ GP15, 1,
+ GP16, 1,
+ GP17, 1,
+ GP18, 1,
+ GP19, 1,
+ GP20, 1,
+ GP21, 1,
+ GP22, 1,
+ GP23, 1,
+ GP24, 1,
+ GP25, 1,
+ GP26, 1,
+ GP27, 1,
+ GP28, 1,
+ GP29, 1,
+ GP30, 1,
+ GP31, 1,
+ Offset(0x18), // GPIO Blink
+ GB00, 8,
+ GB01, 8,
+ GB02, 8,
+ GB03, 8,
+ Offset(0x2c), // GPIO Invert
+ GIV0, 8,
+ GIV1, 8,
+ GIV2, 8,
+ GIV3, 8,
+ Offset(0x30), // GPIO Use Select 2
+ GU04, 8,
+ GU05, 8,
+ GU06, 8,
+ GU07, 8,
+ Offset(0x34), // GPIO IO Select 2
+ GIO4, 8,
+ GIO5, 8,
+ GIO6, 8,
+ GIO7, 8,
+ Offset(0x38), // GPIO Level 2
+ GP32, 1,
+ GP33, 1,
+ GP34, 1,
+ GP35, 1,
+ GP36, 1,
+ GP37, 1,
+ GP38, 1,
+ GP39, 1,
+ GP40, 1,
+ GP41, 1,
+ GP42, 1,
+ GP43, 1,
+ GP44, 1,
+ GP45, 1,
+ GP46, 1,
+ GP47, 1,
+ GP48, 1,
+ GP49, 1,
+ GP50, 1,
+ GP51, 1,
+ GP52, 1,
+ GP53, 1,
+ GP54, 1,
+ GP55, 1,
+ GP56, 1,
+ GP57, 1,
+ GP58, 1,
+ GP59, 1,
+ GP60, 1,
+ GP61, 1,
+ GP62, 1,
+ GP63, 1,
+ Offset(0x40), // GPIO Use Select 3
+ GU08, 8,
+ GU09, 4,
+ Offset(0x44), // GPIO IO Select 3
+ GIO8, 8,
+ GIO9, 4,
+ Offset(0x48), // GPIO Level 3
+ GP64, 1,
+ GP65, 1,
+ GP66, 1,
+ GP67, 1,
+ GP68, 1,
+ GP69, 1,
+ GP70, 1,
+ GP71, 1,
+ GP72, 1,
+ GP73, 1,
+ GP74, 1,
+ GP75, 1,
+ }
+
+
+ // ICH7 Root Complex Register Block. Memory Mapped through RCBA)
+ OperationRegion(RCRB, SystemMemory, DEFAULT_RCBA, 0x4000)
+ Field(RCRB, DWordAcc, Lock, Preserve)
+ {
+ Offset(0x0000), // Backbone
+ Offset(0x1000), // Chipset
+ Offset(0x3000), // Legacy Configuration Registers
+ Offset(0x3404), // High Performance Timer Configuration
+ HPAS, 2, // Address Select
+ , 5,
+ HPTE, 1, // Address Enable
+ Offset(0x3418), // FD (Function Disable)
+ , 1, // Reserved
+ PCID, 1, // PCI bridge disable
+ SA1D, 1, // SATA1 disable
+ SMBD, 1, // SMBUS disable
+ HDAD, 1, // Azalia disable
+ , 8, // Reserved
+ EH2D, 1, // EHCI #2 disable
+ LPBD, 1, // LPC bridge disable
+ EH1D, 1, // EHCI #1 disable
+ RP1D, 1, // Root Port 1 disable
+ RP2D, 1, // Root Port 2 disable
+ RP3D, 1, // Root Port 3 disable
+ RP4D, 1, // Root Port 4 disable
+ RP5D, 1, // Root Port 5 disable
+ RP6D, 1, // Root Port 6 disable
+ RP7D, 1, // Root Port 7 disable
+ RP8D, 1, // Root Port 8 disable
+ TTRD, 1, // Thermal sensor registers disable
+ SA2D, 1, // SATA2 disable
+ Offset(0x3428), // FD2 (Function Disable 2)
+ BDFD, 1, // Display BDF
+ ME1D, 1, // ME Interface 1 disable
+ ME2D, 1, // ME Interface 2 disable
+ IDRD, 1, // IDE redirect disable
+ KTCT, 1, // Keyboard Text redirect disable
+ }
+}
+
+// High Definition Audio (Azalia) 0:1b.0
+#include "audio.asl"
+
+// PCI Express Ports 0:1c.x
+#include "pcie.asl"
+
+// USB 0:1d.0 and 0:1a.0
+#include "usb.asl"
+
+// LPC Bridge 0:1f.0
+#include "lpc.asl"
+
+// SATA 0:1f.2, 0:1f.5
+#include "sata.asl"
+
+// SMBus 0:1f.3
+#include "smbus.asl"
+
+Method (_OSC, 4)
+{
+ /* Check for proper GUID */
+ If (LEqual (Arg0, ToUUID("33DB4D5B-1FF7-401C-9657-7441C03DD766")))
+ {
+ /* Let OS control everything */
+ Return (Arg3)
+ }
+ Else
+ {
+ /* Unrecognized UUID */
+ CreateDWordField (Arg3, 0, CDW1)
+ Or (CDW1, 4, CDW1)
+ Return (Arg3)
+ }
+}
diff --git a/src/southbridge/intel/lynxpoint/acpi/pcie.asl b/src/southbridge/intel/lynxpoint/acpi/pcie.asl
new file mode 100644
index 0000000..934cf78
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/pcie.asl
@@ -0,0 +1,218 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ * Copyright (C) 2012 The Chromium OS Authors. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/* Intel 6/7 Series PCH PCIe support */
+
+// PCI Express Ports
+
+Method (IRQM, 1, Serialized) {
+
+ /* Interrupt Map INTA->INTA, INTB->INTB, INTC->INTC, INTD->INTD */
+ Name (IQAA, Package() {
+ Package() { 0x0000ffff, 0, 0, 16 },
+ Package() { 0x0000ffff, 1, 0, 17 },
+ Package() { 0x0000ffff, 2, 0, 18 },
+ Package() { 0x0000ffff, 3, 0, 19 } })
+ Name (IQAP, Package() {
+ Package() { 0x0000ffff, 0, \_SB.PCI0.LPCB.LNKA, 0 },
+ Package() { 0x0000ffff, 1, \_SB.PCI0.LPCB.LNKB, 0 },
+ Package() { 0x0000ffff, 2, \_SB.PCI0.LPCB.LNKC, 0 },
+ Package() { 0x0000ffff, 3, \_SB.PCI0.LPCB.LNKD, 0 } })
+
+ /* Interrupt Map INTA->INTB, INTB->INTC, INTC->INTD, INTD->INTA */
+ Name (IQBA, Package() {
+ Package() { 0x0000ffff, 0, 0, 17 },
+ Package() { 0x0000ffff, 1, 0, 18 },
+ Package() { 0x0000ffff, 2, 0, 19 },
+ Package() { 0x0000ffff, 3, 0, 16 } })
+ Name (IQBP, Package() {
+ Package() { 0x0000ffff, 0, \_SB.PCI0.LPCB.LNKB, 0 },
+ Package() { 0x0000ffff, 1, \_SB.PCI0.LPCB.LNKC, 0 },
+ Package() { 0x0000ffff, 2, \_SB.PCI0.LPCB.LNKD, 0 },
+ Package() { 0x0000ffff, 3, \_SB.PCI0.LPCB.LNKA, 0 } })
+
+ /* Interrupt Map INTA->INTC, INTB->INTD, INTC->INTA, INTD->INTB */
+ Name (IQCA, Package() {
+ Package() { 0x0000ffff, 0, 0, 18 },
+ Package() { 0x0000ffff, 1, 0, 19 },
+ Package() { 0x0000ffff, 2, 0, 16 },
+ Package() { 0x0000ffff, 3, 0, 17 } })
+ Name (IQCP, Package() {
+ Package() { 0x0000ffff, 0, \_SB.PCI0.LPCB.LNKC, 0 },
+ Package() { 0x0000ffff, 1, \_SB.PCI0.LPCB.LNKD, 0 },
+ Package() { 0x0000ffff, 2, \_SB.PCI0.LPCB.LNKA, 0 },
+ Package() { 0x0000ffff, 3, \_SB.PCI0.LPCB.LNKB, 0 } })
+
+ /* Interrupt Map INTA->INTD, INTB->INTA, INTC->INTB, INTD->INTC */
+ Name (IQDA, Package() {
+ Package() { 0x0000ffff, 0, 0, 19 },
+ Package() { 0x0000ffff, 1, 0, 16 },
+ Package() { 0x0000ffff, 2, 0, 17 },
+ Package() { 0x0000ffff, 3, 0, 18 } })
+ Name (IQDP, Package() {
+ Package() { 0x0000ffff, 0, \_SB.PCI0.LPCB.LNKD, 0 },
+ Package() { 0x0000ffff, 1, \_SB.PCI0.LPCB.LNKA, 0 },
+ Package() { 0x0000ffff, 2, \_SB.PCI0.LPCB.LNKB, 0 },
+ Package() { 0x0000ffff, 3, \_SB.PCI0.LPCB.LNKC, 0 } })
+
+ Switch (ToInteger (Arg0)) {
+ /* PCIe Root Port 1 and 5 */
+ Case (Package() { 1, 5 }) {
+ If (PICM) {
+ Return (IQAA)
+ } Else {
+ Return (IQAP)
+ }
+ }
+
+ /* PCIe Root Port 2 and 6 */
+ Case (Package() { 2, 6 }) {
+ If (PICM) {
+ Return (IQBA)
+ } Else {
+ Return (IQBP)
+ }
+ }
+
+ /* PCIe Root Port 3 and 7 */
+ Case (Package() { 3, 7 }) {
+ If (PICM) {
+ Return (IQCA)
+ } Else {
+ Return (IQCP)
+ }
+ }
+
+ /* PCIe Root Port 4 and 8 */
+ Case (Package() { 4, 8 }) {
+ If (PICM) {
+ Return (IQDA)
+ } Else {
+ Return (IQDP)
+ }
+ }
+
+ Default {
+ If (PICM) {
+ Return (IQDA)
+ } Else {
+ Return (IQDP)
+ }
+ }
+ }
+}
+
+Device (RP01)
+{
+ Name (_ADR, 0x001c0000)
+
+ #include "pcie_port.asl"
+
+ Method (_PRT)
+ {
+ Return (IRQM (RPPN))
+ }
+}
+
+Device (RP02)
+{
+ Name (_ADR, 0x001c0001)
+
+ #include "pcie_port.asl"
+
+ Method (_PRT)
+ {
+ Return (IRQM (RPPN))
+ }
+}
+
+Device (RP03)
+{
+ Name (_ADR, 0x001c0002)
+
+ #include "pcie_port.asl"
+
+ Method (_PRT)
+ {
+ Return (IRQM (RPPN))
+ }
+}
+
+Device (RP04)
+{
+ Name (_ADR, 0x001c0003)
+
+ #include "pcie_port.asl"
+
+ Method (_PRT)
+ {
+ Return (IRQM (RPPN))
+ }
+}
+
+Device (RP05)
+{
+ Name (_ADR, 0x001c0004)
+
+ #include "pcie_port.asl"
+
+ Method (_PRT)
+ {
+ Return (IRQM (RPPN))
+ }
+}
+
+Device (RP06)
+{
+ Name (_ADR, 0x001c0005)
+
+ #include "pcie_port.asl"
+
+ Method (_PRT)
+ {
+ Return (IRQM (RPPN))
+ }
+}
+
+Device (RP07)
+{
+ Name (_ADR, 0x001c0006)
+
+ #include "pcie_port.asl"
+
+ Method (_PRT)
+ {
+ Return (IRQM (RPPN))
+ }
+}
+
+Device (RP08)
+{
+ Name (_ADR, 0x001c0007)
+
+ #include "pcie_port.asl"
+
+ Method (_PRT)
+ {
+ Return (IRQM (RPPN))
+ }
+}
diff --git a/src/southbridge/intel/lynxpoint/acpi/pcie_port.asl b/src/southbridge/intel/lynxpoint/acpi/pcie_port.asl
new file mode 100644
index 0000000..fedd9c9
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/pcie_port.asl
@@ -0,0 +1,30 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2012 The Chromium OS Authors. All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/* Included in each PCIe Root Port device */
+
+OperationRegion (RPCS, PCI_Config, 0x00, 0xFF)
+Field (RPCS, AnyAcc, NoLock, Preserve)
+{
+ Offset (0x4c), // Link Capabilities
+ , 24,
+ RPPN, 8, // Root Port Number
+}
diff --git a/src/southbridge/intel/lynxpoint/acpi/sata.asl b/src/southbridge/intel/lynxpoint/acpi/sata.asl
new file mode 100644
index 0000000..e0c336a
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/sata.asl
@@ -0,0 +1,83 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+// Intel SATA Controller 0:1f.2
+
+// Note: Some BIOSes put the S-ATA code into an SSDT to make it easily
+// pluggable
+
+Device (SATA)
+{
+ Name (_ADR, 0x001f0002)
+
+ Device (PRID)
+ {
+ Name (_ADR, 0)
+
+ // Get Timing Mode
+ Method (_GTM)
+ {
+ Name(PBUF, Buffer(20) {
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
+ 0x00,0x00,0x00,0x00 })
+
+ CreateDwordField (PBUF, 0, PIO0)
+ CreateDwordField (PBUF, 4, DMA0)
+ CreateDwordField (PBUF, 8, PIO1)
+ CreateDwordField (PBUF, 12, DMA1)
+ CreateDwordField (PBUF, 16, FLAG)
+
+ // TODO fill return structure
+
+ Return (PBUF)
+ }
+
+ // Set Timing Mode
+ Method (_STM, 3)
+ {
+ CreateDwordField (Arg0, 0, PIO0)
+ CreateDwordField (Arg0, 4, DMA0)
+ CreateDwordField (Arg0, 8, PIO1)
+ CreateDwordField (Arg0, 12, DMA1)
+ CreateDwordField (Arg0, 16, FLAG)
+
+ // TODO: Do the deed
+ }
+
+ Device (DSK0)
+ {
+ Name (_ADR, 0)
+ // TODO: _RMV ?
+ // TODO: _GTF ?
+ }
+
+ Device (DSK1)
+ {
+ Name (_ADR, 1)
+
+ // TODO: _RMV ?
+ // TODO: _GTF ?
+ }
+
+ }
+}
+
diff --git a/src/southbridge/intel/lynxpoint/acpi/sleepstates.asl b/src/southbridge/intel/lynxpoint/acpi/sleepstates.asl
new file mode 100644
index 0000000..06bfcb6
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/sleepstates.asl
@@ -0,0 +1,27 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+Name(\_S0, Package(){0x0,0x0,0x0,0x0})
+// Name(\_S1, Package(){0x1,0x1,0x0,0x0})
+Name(\_S3, Package(){0x5,0x5,0x0,0x0})
+Name(\_S4, Package(){0x6,0x6,0x0,0x0})
+Name(\_S5, Package(){0x7,0x7,0x0,0x0})
+
diff --git a/src/southbridge/intel/lynxpoint/acpi/smbus.asl b/src/southbridge/intel/lynxpoint/acpi/smbus.asl
new file mode 100644
index 0000000..4409308
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/smbus.asl
@@ -0,0 +1,242 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+// Intel SMBus Controller 0:1f.3
+
+Device (SBUS)
+{
+ Name (_ADR, 0x001f0003)
+
+#ifdef ENABLE_SMBUS_METHODS
+ OperationRegion (SMBP, PCI_Config, 0x00, 0x100)
+ Field(SMBP, DWordAcc, NoLock, Preserve)
+ {
+ Offset(0x40),
+ , 2,
+ I2CE, 1
+ }
+
+ OperationRegion (SMBI, SystemIO, SMBUS_IO_BASE, 0x20)
+ Field (SMBI, ByteAcc, NoLock, Preserve)
+ {
+ HSTS, 8, // Host Status
+ , 8,
+ HCNT, 8, // Host Control
+ HCMD, 8, // Host Command
+ TXSA, 8, // Transmit Slave Address
+ DAT0, 8, // Host Data 0
+ DAT1, 8, // Host Data 1
+ HBDB, 8, // Host Block Data Byte
+ PECK, 8, // Packet Error Check
+ RXSA, 8, // Receive Slave Address
+ RXDA, 16, // Receive Slave Data
+ AUXS, 8, // Auxiliary Status
+ AUXC, 8, // Auxiliary Control
+ SLPC, 8, // SMLink Pin Control
+ SBPC, 8, // SMBus Pin Control
+ SSTS, 8, // Slave Status
+ SCMD, 8, // Slave Command
+ NADR, 8, // Notify Device Address
+ NDLB, 8, // Notify Data Low Byte
+ NDLH, 8, // Notify Data High Byte
+ }
+
+ // Kill all SMBus communication
+ Method (KILL, 0, Serialized)
+ {
+ Or (HCNT, 0x02, HCNT) // Send Kill
+ Or (HSTS, 0xff, HSTS) // Clean Status
+ }
+
+ // Check if last operation completed
+ // return Failure = 0, Success = 1
+ Method (CMPL, 0, Serialized)
+ {
+ Store (4000, Local0) // Timeout 200ms in 50us steps
+ While (Local0) {
+ If (And(HSTS, 0x02)) { // Completion Status?
+ Return (1) // Operation Completed
+ } Else {
+ Stall (50)
+ Decrement (Local0)
+ If (LEqual(Local0, 0)) {
+ KILL()
+ }
+ }
+ }
+
+ Return (0) // Failure
+ }
+
+
+ // Wait for SMBus to become ready
+ Method (SRDY, 0, Serialized)
+ {
+ Store (200, Local0) // Timeout 200ms
+ While (Local0) {
+ If (And(HSTS, 0x40)) { // IN_USE?
+ Sleep(1) // Wait 1ms
+ Decrement(Local0) // timeout--
+ If (LEqual(Local0, 0)) {
+ Return (1)
+ }
+ } Else {
+ Store (0, Local0) // We're ready
+ }
+ }
+
+ Store (4000, Local0) // Timeout 200ms (50us * 4000)
+ While (Local0) {
+ If (And (HSTS, 0x01)) { // Host Busy?
+ Stall(50) // Wait 50us
+ Decrement(Local0) // timeout--
+ If (LEqual(Local0, 0)) {
+ KILL()
+ }
+ } Else {
+ Return (0) // Success
+ }
+ }
+
+ Return (1) // Failure
+ }
+
+ // SMBus Send Byte
+ // Arg0: Address
+ // Arg1: Data
+ // Return: 1 = Success, 0=Failure
+
+ Method (SSXB, 2, Serialized)
+ {
+
+ // Is the SMBus Controller Ready?
+ If (SRDY()) {
+ Return (0)
+ }
+
+ // Send Byte
+ Store (0, I2CE) // SMBus Enable
+ Store (0xbf, HSTS)
+ Store (Arg0, TXSA) // Write Address
+ Store (Arg1, HCMD) // Write Data
+
+ Store (0x48, HCNT) // Start + Byte Data Protocol
+
+ If (CMPL()) {
+ Or (HSTS, 0xff, HSTS) // Clean up
+ Return (1) // Success
+ }
+
+ Return (0)
+ }
+
+
+ // SMBus Receive Byte
+ // Arg0: Address
+ // Return: 0xffff = Failure, Data (8bit) = Success
+
+ Method (SRXB, 2, Serialized)
+ {
+
+ // Is the SMBus Controller Ready?
+ If (SRDY()) {
+ Return (0xffff)
+ }
+
+ // Receive Byte
+ Store (0, I2CE) // SMBus Enable
+ Store (0xbf, HSTS)
+ Store (Or (Arg0, 1), TXSA) // Write Address
+
+ Store (0x44, HCNT) // Start
+
+ If (CMPL()) {
+ Or (HSTS, 0xff, HSTS) // Clean up
+ Return (DAT0) // Success
+ }
+
+ Return (0xffff)
+ }
+
+
+ // SMBus Write Byte
+ // Arg0: Address
+ // Arg1: Command
+ // Arg2: Data
+ // Return: 1 = Success, 0=Failure
+
+ Method (SWRB, 3, Serialized)
+ {
+
+ // Is the SMBus Controller Ready?
+ If (SRDY()) {
+ Return (0)
+ }
+
+ // Send Byte
+ Store (0, I2CE) // SMBus Enable
+ Store (0xbf, HSTS)
+ Store (Arg0, TXSA) // Write Address
+ Store (Arg1, HCMD) // Write Command
+ Store (Arg2, DAT0) // Write Data
+
+ Store (0x48, HCNT) // Start + Byte Protocol
+
+ If (CMPL()) {
+ Or (HSTS, 0xff, HSTS) // Clean up
+ Return (1) // Success
+ }
+
+ Return (0)
+ }
+
+
+ // SMBus Read Byte
+ // Arg0: Address
+ // Arg1: Command
+ // Return: 0xffff = Failure, Data (8bit) = Success
+
+ Method (SRDB, 2, Serialized)
+ {
+
+ // Is the SMBus Controller Ready?
+ If (SRDY()) {
+ Return (0xffff)
+ }
+
+ // Receive Byte
+ Store (0, I2CE) // SMBus Enable
+ Store (0xbf, HSTS)
+ Store (Or (Arg0, 1), TXSA) // Write Address
+ Store (Arg1, HCMD) // Command
+
+ Store (0x48, HCNT) // Start
+
+ If (CMPL()) {
+ Or (HSTS, 0xff, HSTS) // Clean up
+ Return (DAT0) // Success
+ }
+
+ Return (0xffff)
+ }
+#endif
+}
+
diff --git a/src/southbridge/intel/lynxpoint/acpi/usb.asl b/src/southbridge/intel/lynxpoint/acpi/usb.asl
new file mode 100644
index 0000000..cf3e6a0
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/acpi/usb.asl
@@ -0,0 +1,91 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/* Intel Cougar Point USB support */
+
+// EHCI Controller 0:1d.0
+
+Device (EHC1)
+{
+ Name(_ADR, 0x001d0000)
+
+ Name (_PRW, Package(){ 13, 4 }) // Power Resources for Wake
+
+ // Leave USB ports on for to allow Wake from USB
+
+ Method(_S3D,0) // Highest D State in S3 State
+ {
+ Return (2)
+ }
+
+ Method(_S4D,0) // Highest D State in S4 State
+ {
+ Return (2)
+ }
+
+ Device (HUB7)
+ {
+ Name (_ADR, 0x00000000)
+
+ // How many are there?
+ Device (PRT1) { Name (_ADR, 1) } // USB Port 0
+ Device (PRT2) { Name (_ADR, 2) } // USB Port 1
+ Device (PRT3) { Name (_ADR, 3) } // USB Port 2
+ Device (PRT4) { Name (_ADR, 4) } // USB Port 3
+ Device (PRT5) { Name (_ADR, 5) } // USB Port 4
+ Device (PRT6) { Name (_ADR, 6) } // USB Port 5
+ }
+}
+
+// EHCI #2 Controller 0:1a.0
+
+Device (EHC2)
+{
+ Name(_ADR, 0x001a0000)
+
+ Name (_PRW, Package(){ 13, 4 }) // Power Resources for Wake
+
+ // Leave USB ports on for to allow Wake from USB
+
+ Method(_S3D,0) // Highest D State in S3 State
+ {
+ Return (2)
+ }
+
+ Method(_S4D,0) // Highest D State in S4 State
+ {
+ Return (2)
+ }
+
+ Device (HUB7)
+ {
+ Name (_ADR, 0x00000000)
+
+ // How many are there?
+ Device (PRT1) { Name (_ADR, 1) } // USB Port 0
+ Device (PRT2) { Name (_ADR, 2) } // USB Port 1
+ Device (PRT3) { Name (_ADR, 3) } // USB Port 2
+ Device (PRT4) { Name (_ADR, 4) } // USB Port 3
+ Device (PRT5) { Name (_ADR, 5) } // USB Port 4
+ Device (PRT6) { Name (_ADR, 6) } // USB Port 5
+ }
+}
+
diff --git a/src/southbridge/intel/lynxpoint/azalia.c b/src/southbridge/intel/lynxpoint/azalia.c
new file mode 100644
index 0000000..7b51671
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/azalia.c
@@ -0,0 +1,375 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008 Advanced Micro Devices, Inc.
+ * Copyright (C) 2008-2009 coresystems GmbH
+ * Copyright (C) 2011 The ChromiumOS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <arch/io.h>
+#include <delay.h>
+#include "pch.h"
+
+#define HDA_ICII_REG 0x68
+#define HDA_ICII_BUSY (1 << 0)
+#define HDA_ICII_VALID (1 << 1)
+
+typedef struct southbridge_intel_bd82x6x_config config_t;
+
+static int set_bits(u32 port, u32 mask, u32 val)
+{
+ u32 reg32;
+ int count;
+
+ /* Write (val & mask) to port */
+ val &= mask;
+ reg32 = read32(port);
+ reg32 &= ~mask;
+ reg32 |= val;
+ write32(port, reg32);
+
+ /* Wait for readback of register to
+ * match what was just written to it
+ */
+ count = 50;
+ do {
+ /* Wait 1ms based on BKDG wait time */
+ mdelay(1);
+ reg32 = read32(port);
+ reg32 &= mask;
+ } while ((reg32 != val) && --count);
+
+ /* Timeout occurred */
+ if (!count)
+ return -1;
+ return 0;
+}
+
+static int codec_detect(u32 base)
+{
+ u8 reg8;
+
+ /* Set Bit 0 to 1 to exit reset state (BAR + 0x8)[0] */
+ if (set_bits(base + 0x08, 1, 1) == -1)
+ goto no_codec;
+
+ /* Write back the value once reset bit is set. */
+ write16(base + 0x0, read16(base + 0x0));
+
+ /* Read in Codec location (BAR + 0xe)[2..0]*/
+ reg8 = read8(base + 0xe);
+ reg8 &= 0x0f;
+ if (!reg8)
+ goto no_codec;
+
+ return reg8;
+
+no_codec:
+ /* Codec Not found */
+ /* Put HDA back in reset (BAR + 0x8) [0] */
+ set_bits(base + 0x08, 1, 0);
+ printk(BIOS_DEBUG, "Azalia: No codec!\n");
+ return 0;
+}
+
+const u32 * cim_verb_data = NULL;
+u32 cim_verb_data_size = 0;
+const u32 * pc_beep_verbs = NULL;
+u32 pc_beep_verbs_size = 0;
+
+static u32 find_verb(struct device *dev, u32 viddid, const u32 ** verb)
+{
+ int idx=0;
+
+ while (idx < (cim_verb_data_size / sizeof(u32))) {
+ u32 verb_size = 4 * cim_verb_data[idx+2]; // in u32
+ if (cim_verb_data[idx] != viddid) {
+ idx += verb_size + 3; // skip verb + header
+ continue;
+ }
+ *verb = &cim_verb_data[idx+3];
+ return verb_size;
+ }
+
+ /* Not all codecs need to load another verb */
+ return 0;
+}
+
+/**
+ * Wait 50usec for the codec to indicate it is ready
+ * no response would imply that the codec is non-operative
+ */
+
+static int wait_for_ready(u32 base)
+{
+ /* Use a 50 usec timeout - the Linux kernel uses the
+ * same duration */
+
+ int timeout = 50;
+
+ while(timeout--) {
+ u32 reg32 = read32(base + HDA_ICII_REG);
+ if (!(reg32 & HDA_ICII_BUSY))
+ return 0;
+ udelay(1);
+ }
+
+ return -1;
+}
+
+/**
+ * Wait 50usec for the codec to indicate that it accepted
+ * the previous command. No response would imply that the code
+ * is non-operative
+ */
+
+static int wait_for_valid(u32 base)
+{
+ u32 reg32;
+
+ /* Send the verb to the codec */
+ reg32 = read32(base + HDA_ICII_REG);
+ reg32 |= HDA_ICII_BUSY | HDA_ICII_VALID;
+ write32(base + HDA_ICII_REG, reg32);
+
+ /* Use a 50 usec timeout - the Linux kernel uses the
+ * same duration */
+
+ int timeout = 50;
+ while(timeout--) {
+ reg32 = read32(base + HDA_ICII_REG);
+ if ((reg32 & (HDA_ICII_VALID | HDA_ICII_BUSY)) ==
+ HDA_ICII_VALID)
+ return 0;
+ udelay(1);
+ }
+
+ return -1;
+}
+
+static void codec_init(struct device *dev, u32 base, int addr)
+{
+ u32 reg32;
+ const u32 *verb;
+ u32 verb_size;
+ int i;
+
+ printk(BIOS_DEBUG, "Azalia: Initializing codec #%d\n", addr);
+
+ /* 1 */
+ if (wait_for_ready(base) == -1) {
+ printk(BIOS_DEBUG, " codec not ready.\n");
+ return;
+ }
+
+ reg32 = (addr << 28) | 0x000f0000;
+ write32(base + 0x60, reg32);
+
+ if (wait_for_valid(base) == -1) {
+ printk(BIOS_DEBUG, " codec not valid.\n");
+ return;
+ }
+
+ reg32 = read32(base + 0x64);
+
+ /* 2 */
+ printk(BIOS_DEBUG, "Azalia: codec viddid: %08x\n", reg32);
+ verb_size = find_verb(dev, reg32, &verb);
+
+ if (!verb_size) {
+ printk(BIOS_DEBUG, "Azalia: No verb!\n");
+ return;
+ }
+ printk(BIOS_DEBUG, "Azalia: verb_size: %d\n", verb_size);
+
+ /* 3 */
+ for (i = 0; i < verb_size; i++) {
+ if (wait_for_ready(base) == -1)
+ return;
+
+ write32(base + 0x60, verb[i]);
+
+ if (wait_for_valid(base) == -1)
+ return;
+ }
+ printk(BIOS_DEBUG, "Azalia: verb loaded.\n");
+}
+
+static void codecs_init(struct device *dev, u32 base, u32 codec_mask)
+{
+ int i;
+ for (i = 3; i >= 0; i--) {
+ if (codec_mask & (1 << i))
+ codec_init(dev, base, i);
+ }
+
+ for (i = 0; i < pc_beep_verbs_size; i++) {
+ if (wait_for_ready(base) == -1)
+ return;
+
+ write32(base + 0x60, pc_beep_verbs[i]);
+
+ if (wait_for_valid(base) == -1)
+ return;
+ }
+}
+
+static void azalia_init(struct device *dev)
+{
+ u32 base;
+ struct resource *res;
+ u32 codec_mask;
+ u8 reg8;
+ u16 reg16;
+ u32 reg32;
+
+ /* Find base address */
+ res = find_resource(dev, PCI_BASE_ADDRESS_0);
+ if (!res)
+ return;
+
+ // NOTE this will break as soon as the Azalia get's a bar above
+ // 4G. Is there anything we can do about it?
+ base = (u32)res->base;
+ printk(BIOS_DEBUG, "Azalia: base = %08x\n", (u32)base);
+
+ if (RCBA32(0x2030) & (1 << 31)) {
+ reg32 = pci_mmio_read_config32(dev, 0x120);
+ reg32 &= 0xf8ffff01;
+ reg32 |= (1 << 24); // 25 for server
+ reg32 |= RCBA32(0x2030) & 0xfe;
+ pci_mmio_write_config32(dev, 0x120, reg32);
+
+ reg16 = pci_mmio_read_config16(dev, 0x78);
+ reg16 &= ~(1 << 11);
+ pci_mmio_write_config16(dev, 0x78, reg16);
+ } else
+ printk(BIOS_DEBUG, "Azalia: V1CTL disabled.\n");
+
+ reg32 = pci_mmio_read_config32(dev, 0x114);
+ reg32 &= ~0xfe;
+ pci_mmio_write_config32(dev, 0x114, reg32);
+
+ // Set VCi enable bit
+ if (pci_mmio_read_config32(dev, 0x120) & ((1 << 24) |
+ (1 << 25) | (1 << 26))) {
+ reg32 = pci_mmio_read_config32(dev, 0x120);
+ reg32 |= (1 << 31);
+ pci_mmio_write_config32(dev, 0x120, reg32);
+ }
+
+ // Enable HDMI codec:
+ reg32 = pci_read_config32(dev, 0xc4);
+ reg32 |= (1 << 1);
+ pci_write_config32(dev, 0xc4, reg32);
+
+ reg8 = pci_read_config8(dev, 0x43);
+ reg8 |= (1 << 6);
+ pci_write_config8(dev, 0x43, reg8);
+
+ /* Additional programming steps */
+ reg32 = pci_read_config32(dev, 0xc4);
+ reg32 |= (1 << 13) | (1 << 10);
+ pci_write_config32(dev, 0xc4, reg32);
+
+ reg32 = pci_read_config32(dev, 0xd0);
+ reg32 &= ~(1 << 31);
+ pci_write_config32(dev, 0xd0, reg32);
+
+ /* Additional programming steps */
+ reg32 = pci_read_config32(dev, 0xc4);
+ reg32 |= (1 << 13);
+ pci_write_config32(dev, 0xc4, reg32);
+
+ reg32 = pci_read_config32(dev, 0xc4);
+ reg32 |= (1 << 10);
+ pci_write_config32(dev, 0xc4, reg32);
+
+ reg32 = pci_read_config32(dev, 0xd0);
+ reg32 &= ~(1 << 31);
+ pci_write_config32(dev, 0xd0, reg32);
+
+ /* Set Bus Master */
+ reg32 = pci_read_config32(dev, PCI_COMMAND);
+ pci_write_config32(dev, PCI_COMMAND, reg32 | PCI_COMMAND_MASTER);
+
+ pci_write_config8(dev, 0x3c, 0x0a); // unused?
+
+ /* Codec Initialization Programming Sequence */
+ reg32 = read32(base + 0x08);
+ reg32 |= (1 << 0);
+ write32(base + 0x08, reg32);
+
+ //
+ reg8 = pci_read_config8(dev, 0x40); // Audio Control
+ reg8 |= 1; // Select Azalia mode. This needs to be controlled via devicetree.cb
+ pci_write_config8(dev, 0x40, reg8);
+
+ reg8 = pci_read_config8(dev, 0x4d); // Docking Status
+ reg8 &= ~(1 << 7); // Docking not supported
+ pci_write_config8(dev, 0x4d, reg8);
+
+ codec_mask = codec_detect(base);
+
+ if (codec_mask) {
+ printk(BIOS_DEBUG, "Azalia: codec_mask = %02x\n", codec_mask);
+ codecs_init(dev, base, codec_mask);
+ }
+
+ /* Enable dynamic clock gating */
+ reg8 = pci_read_config8(dev, 0x43);
+ reg8 &= ~0x7;
+ reg8 |= (1 << 2) | (1 << 0);
+ pci_write_config8(dev, 0x43, reg8);
+}
+
+static void azalia_set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ if (!vendor || !device) {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ pci_read_config32(dev, PCI_VENDOR_ID));
+ } else {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+ }
+}
+
+static struct pci_operations azalia_pci_ops = {
+ .set_subsystem = azalia_set_subsystem,
+};
+
+static struct device_operations azalia_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = azalia_init,
+ .scan_bus = 0,
+ .ops_pci = &azalia_pci_ops,
+};
+
+static const unsigned short pci_device_ids[] = { 0x1c20, 0x1e20, 0 };
+
+static const struct pci_driver pch_azalia __pci_driver = {
+ .ops = &azalia_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .devices = pci_device_ids,
+};
+
diff --git a/src/southbridge/intel/lynxpoint/bootblock.c b/src/southbridge/intel/lynxpoint/bootblock.c
new file mode 100644
index 0000000..2770d55
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/bootblock.c
@@ -0,0 +1,101 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2011 Google Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <cpu/x86/tsc.h>
+#include "pch.h"
+
+static void store_initial_timestamp(void)
+{
+ /* On Cougar Point we have two 32bit scratchpad registers available:
+ * D0:F0 0xdc (SKPAD)
+ * D31:F2 0xd0 (SATA SP)
+ */
+ tsc_t tsc = rdtsc();
+ pci_write_config32(PCI_DEV(0, 0x00, 0), 0xdc, tsc.lo);
+ pci_write_config32(PCI_DEV(0, 0x1f, 2), 0xd0, tsc.hi);
+}
+
+/*
+ * Enable Prefetching and Caching.
+ */
+static void enable_spi_prefetch(void)
+{
+ u8 reg8;
+ device_t dev;
+
+ dev = PCI_DEV(0, 0x1f, 0);
+
+ reg8 = pci_read_config8(dev, 0xdc);
+ reg8 &= ~(3 << 2);
+ reg8 |= (2 << 2); /* Prefetching and Caching Enabled */
+ pci_write_config8(dev, 0xdc, reg8);
+}
+
+
+static void map_rcba(void)
+{
+ device_t dev = PCI_DEV(0, 0x1f, 0);
+
+ pci_write_config32(dev, RCBA, DEFAULT_RCBA | 1);
+}
+
+static void enable_port80_on_lpc(void)
+{
+ /* Enable port 80 POST on LPC. The chipset does this by deafult,
+ * but it doesn't appear to hurt anything. */
+ u32 gcs = RCBA32(GCS);
+ gcs = gcs & ~0x4;
+ RCBA32(GCS) = gcs;
+}
+
+static void set_spi_speed(void)
+{
+ u32 fdod;
+ u8 ssfc;
+
+ /* Observe SPI Descriptor Component Section 0 */
+ SPIBAR32(FDOC) = 0x1000;
+
+ /* Extract the Write/Erase SPI Frequency from descriptor */
+ fdod = SPIBAR32(FDOD);
+ fdod >>= 24;
+ fdod &= 7;
+
+ /* Set Software Sequence frequency to match */
+ ssfc = SPIBAR8(SSFC + 2);
+ ssfc &= ~7;
+ ssfc |= fdod;
+ SPIBAR8(SSFC + 2) = ssfc;
+}
+
+static void bootblock_southbridge_init(void)
+{
+#if CONFIG_COLLECT_TIMESTAMPS
+ store_initial_timestamp();
+#endif
+ map_rcba();
+ enable_spi_prefetch();
+ enable_port80_on_lpc();
+ set_spi_speed();
+
+ /* Enable upper 128bytes of CMOS */
+ RCBA32(RC) = (1 << 2);
+}
diff --git a/src/southbridge/intel/lynxpoint/chip.h b/src/southbridge/intel/lynxpoint/chip.h
new file mode 100644
index 0000000..1e6195b
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/chip.h
@@ -0,0 +1,84 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef SOUTHBRIDGE_INTEL_LYNXPOINT_CHIP_H
+#define SOUTHBRIDGE_INTEL_LYNXPOINT_CHIP_H
+
+struct southbridge_intel_lynxpoint_config {
+ /**
+ * Interrupt Routing configuration
+ * If bit7 is 1, the interrupt is disabled.
+ */
+ uint8_t pirqa_routing;
+ uint8_t pirqb_routing;
+ uint8_t pirqc_routing;
+ uint8_t pirqd_routing;
+ uint8_t pirqe_routing;
+ uint8_t pirqf_routing;
+ uint8_t pirqg_routing;
+ uint8_t pirqh_routing;
+
+ /**
+ * GPI Routing configuration
+ *
+ * Only the lower two bits have a meaning:
+ * 00: No effect
+ * 01: SMI# (if corresponding ALT_GPI_SMI_EN bit is also set)
+ * 10: SCI (if corresponding GPIO_EN bit is also set)
+ * 11: reserved
+ */
+ uint8_t gpi0_routing;
+ uint8_t gpi1_routing;
+ uint8_t gpi2_routing;
+ uint8_t gpi3_routing;
+ uint8_t gpi4_routing;
+ uint8_t gpi5_routing;
+ uint8_t gpi6_routing;
+ uint8_t gpi7_routing;
+ uint8_t gpi8_routing;
+ uint8_t gpi9_routing;
+ uint8_t gpi10_routing;
+ uint8_t gpi11_routing;
+ uint8_t gpi12_routing;
+ uint8_t gpi13_routing;
+ uint8_t gpi14_routing;
+ uint8_t gpi15_routing;
+
+ uint32_t gpe0_en;
+ uint16_t alt_gp_smi_en;
+
+ /* IDE configuration */
+ uint32_t ide_legacy_combined;
+ uint32_t sata_ahci;
+ uint8_t sata_port_map;
+ uint32_t sata_port0_gen3_tx;
+ uint32_t sata_port1_gen3_tx;
+
+ uint32_t gen1_dec;
+ uint32_t gen2_dec;
+ uint32_t gen3_dec;
+ uint32_t gen4_dec;
+
+ /* Enable linear PCIe Root Port function numbers starting at zero */
+ uint8_t pcie_port_coalesce;
+};
+
+extern struct chip_operations southbridge_intel_lynxpoint_ops;
+
+#endif /* SOUTHBRIDGE_INTEL_LYNXPOINT_CHIP_H */
diff --git a/src/southbridge/intel/lynxpoint/early_me.c b/src/southbridge/intel/lynxpoint/early_me.c
new file mode 100644
index 0000000..5b266cc
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/early_me.c
@@ -0,0 +1,201 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2011 The Chromium OS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <arch/hlt.h>
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <console/console.h>
+#include <delay.h>
+#include <device/pci_ids.h>
+#include <string.h>
+#include "me.h"
+#include "pch.h"
+
+static const char *me_ack_values[] = {
+ [ME_HFS_ACK_NO_DID] = "No DID Ack received",
+ [ME_HFS_ACK_RESET] = "Non-power cycle reset",
+ [ME_HFS_ACK_PWR_CYCLE] = "Power cycle reset",
+ [ME_HFS_ACK_S3] = "Go to S3",
+ [ME_HFS_ACK_S4] = "Go to S4",
+ [ME_HFS_ACK_S5] = "Go to S5",
+ [ME_HFS_ACK_GBL_RESET] = "Global Reset",
+ [ME_HFS_ACK_CONTINUE] = "Continue to boot"
+};
+
+static inline void pci_read_dword_ptr(void *ptr, int offset)
+{
+ u32 dword = pci_read_config32(PCH_ME_DEV, offset);
+ memcpy(ptr, &dword, sizeof(dword));
+}
+
+static inline void pci_write_dword_ptr(void *ptr, int offset)
+{
+ u32 dword = 0;
+ memcpy(&dword, ptr, sizeof(dword));
+ pci_write_config32(PCH_ME_DEV, offset, dword);
+}
+
+void intel_early_me_status(void)
+{
+ struct me_hfs hfs;
+ struct me_gmes gmes;
+
+ pci_read_dword_ptr(&hfs, PCI_ME_HFS);
+ pci_read_dword_ptr(&gmes, PCI_ME_GMES);
+
+ intel_me_status(&hfs, &gmes);
+}
+
+int intel_early_me_init(void)
+{
+ int count;
+ struct me_uma uma;
+ struct me_hfs hfs;
+
+ printk(BIOS_INFO, "Intel ME early init\n");
+
+ /* Wait for ME UMA SIZE VALID bit to be set */
+ for (count = ME_RETRY; count > 0; --count) {
+ pci_read_dword_ptr(&uma, PCI_ME_UMA);
+ if (uma.valid)
+ break;
+ udelay(ME_DELAY);
+ }
+ if (!count) {
+ printk(BIOS_ERR, "ERROR: ME is not ready!\n");
+ return -1;
+ }
+
+ /* Check for valid firmware */
+ pci_read_dword_ptr(&hfs, PCI_ME_HFS);
+ if (hfs.fpt_bad) {
+ printk(BIOS_WARNING, "WARNING: ME has bad firmware\n");
+ return -1;
+ }
+
+ printk(BIOS_INFO, "Intel ME firmware is ready\n");
+ return 0;
+}
+
+int intel_early_me_uma_size(void)
+{
+ struct me_uma uma;
+
+ pci_read_dword_ptr(&uma, PCI_ME_UMA);
+ if (uma.valid) {
+ printk(BIOS_DEBUG, "ME: Requested %uMB UMA\n", uma.size);
+ return uma.size;
+ }
+
+ printk(BIOS_DEBUG, "ME: Invalid UMA size\n");
+ return 0;
+}
+
+static inline void set_global_reset(int enable)
+{
+ u32 etr3 = pci_read_config32(PCH_LPC_DEV, ETR3);
+
+ /* Clear CF9 Without Resume Well Reset Enable */
+ etr3 &= ~ETR3_CWORWRE;
+
+ /* CF9GR indicates a Global Reset */
+ if (enable)
+ etr3 |= ETR3_CF9GR;
+ else
+ etr3 &= ~ETR3_CF9GR;
+
+ pci_write_config32(PCH_LPC_DEV, ETR3, etr3);
+}
+
+int intel_early_me_init_done(u8 status)
+{
+ u8 reset;
+ int count;
+ u32 mebase_l, mebase_h;
+ struct me_hfs hfs;
+ struct me_did did = {
+ .init_done = ME_INIT_DONE,
+ .status = status
+ };
+
+ /* MEBASE from MESEG_BASE[35:20] */
+ mebase_l = pci_read_config32(PCI_CPU_DEVICE, PCI_CPU_MEBASE_L);
+ mebase_h = pci_read_config32(PCI_CPU_DEVICE, PCI_CPU_MEBASE_H) & 0xf;
+ did.uma_base = (mebase_l >> 20) | (mebase_h << 12);
+
+ /* Send message to ME */
+ printk(BIOS_DEBUG, "ME: Sending Init Done with status: %d, "
+ "UMA base: 0x%04x\n", status, did.uma_base);
+
+ pci_write_dword_ptr(&did, PCI_ME_H_GS);
+
+ /* Must wait for ME acknowledgement */
+ for (count = ME_RETRY; count > 0; --count) {
+ pci_read_dword_ptr(&hfs, PCI_ME_HFS);
+ if (hfs.bios_msg_ack)
+ break;
+ udelay(ME_DELAY);
+ }
+ if (!count) {
+ printk(BIOS_ERR, "ERROR: ME failed to respond\n");
+ return -1;
+ }
+
+ /* Return the requested BIOS action */
+ printk(BIOS_NOTICE, "ME: Requested BIOS Action: %s\n",
+ me_ack_values[hfs.ack_data]);
+
+ /* Check status after acknowledgement */
+ intel_early_me_status();
+
+ reset = 0;
+ switch (hfs.ack_data) {
+ case ME_HFS_ACK_CONTINUE:
+ /* Continue to boot */
+ return 0;
+ case ME_HFS_ACK_RESET:
+ /* Non-power cycle reset */
+ set_global_reset(0);
+ reset = 0x06;
+ break;
+ case ME_HFS_ACK_PWR_CYCLE:
+ /* Power cycle reset */
+ set_global_reset(0);
+ reset = 0x0e;
+ break;
+ case ME_HFS_ACK_GBL_RESET:
+ /* Global reset */
+ set_global_reset(1);
+ reset = 0x0e;
+ break;
+ case ME_HFS_ACK_S3:
+ case ME_HFS_ACK_S4:
+ case ME_HFS_ACK_S5:
+ break;
+ }
+
+ /* Perform the requested reset */
+ if (reset) {
+ outb(reset, 0xcf9);
+ hlt();
+ }
+ return -1;
+}
diff --git a/src/southbridge/intel/lynxpoint/early_smbus.c b/src/southbridge/intel/lynxpoint/early_smbus.c
new file mode 100644
index 0000000..a626649
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/early_smbus.c
@@ -0,0 +1,63 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <console/console.h>
+#include <device/pci_ids.h>
+#include <device/pci_def.h>
+#include "pch.h"
+#include "smbus.h"
+
+void enable_smbus(void)
+{
+ device_t dev;
+
+ /* Set the SMBus device statically. */
+ dev = PCI_DEV(0x0, 0x1f, 0x3);
+
+ /* Check to make sure we've got the right device. */
+ if (pci_read_config16(dev, 0x0) != 0x8086) {
+ die("SMBus controller not found!");
+ }
+
+ /* Set SMBus I/O base. */
+ pci_write_config32(dev, SMB_BASE,
+ SMBUS_IO_BASE | PCI_BASE_ADDRESS_SPACE_IO);
+
+ /* Set SMBus enable. */
+ pci_write_config8(dev, HOSTC, HST_EN);
+
+ /* Set SMBus I/O space enable. */
+ pci_write_config16(dev, PCI_COMMAND, PCI_COMMAND_IO);
+
+ /* Disable interrupt generation. */
+ outb(0, SMBUS_IO_BASE + SMBHSTCTL);
+
+ /* Clear any lingering errors, so transactions can run. */
+ outb(inb(SMBUS_IO_BASE + SMBHSTSTAT), SMBUS_IO_BASE + SMBHSTSTAT);
+ print_debug("SMBus controller enabled.\n");
+}
+
+int smbus_read_byte(unsigned device, unsigned address)
+{
+ return do_smbus_read_byte(SMBUS_IO_BASE, device, address);
+}
+
diff --git a/src/southbridge/intel/lynxpoint/early_spi.c b/src/southbridge/intel/lynxpoint/early_spi.c
new file mode 100644
index 0000000..ddfc4c2
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/early_spi.c
@@ -0,0 +1,115 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2012 Google Inc. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <console/console.h>
+#include <device/pci_ids.h>
+#include <device/pci_def.h>
+#include <delay.h>
+#include "pch.h"
+
+#define SPI_DELAY 10 /* 10us */
+#define SPI_RETRY 200000 /* 2s */
+
+static int early_spi_read_block(u32 offset, u8 size, u8 *buffer)
+{
+ u32 *ptr32 = (u32*)buffer;
+ u32 i;
+
+ /* Clear status bits */
+ RCBA16(SPIBAR_HSFS) |= SPIBAR_HSFS_AEL | SPIBAR_HSFS_FCERR |
+ SPIBAR_HSFS_FDONE;
+
+ if (RCBA16(SPIBAR_HSFS) & SPIBAR_HSFS_SCIP) {
+ printk(BIOS_ERR, "SPI ERROR: transaction in progress\n");
+ return -1;
+ }
+
+ /* Set flash address */
+ RCBA32(SPIBAR_FADDR) = offset;
+
+ /* Setup read transaction */
+ RCBA16(SPIBAR_HSFC) = SPIBAR_HSFC_BYTE_COUNT(size) |
+ SPIBAR_HSFC_CYCLE_READ;
+
+ /* Start transactinon */
+ RCBA16(SPIBAR_HSFC) |= SPIBAR_HSFC_GO;
+
+ /* Wait for completion */
+ for (i = 0; i < SPI_RETRY; i++) {
+ if (RCBA16(SPIBAR_HSFS) & SPIBAR_HSFS_SCIP) {
+ /* Cycle in progress, wait 1ms */
+ udelay(SPI_DELAY);
+ continue;
+ }
+
+ if (RCBA16(SPIBAR_HSFS) & SPIBAR_HSFS_AEL) {
+ printk(BIOS_ERR, "SPI ERROR: Access Error\n");
+ return -1;
+
+ }
+
+ if (RCBA16(SPIBAR_HSFS) & SPIBAR_HSFS_FCERR) {
+ printk(BIOS_ERR, "SPI ERROR: Flash Cycle Error\n");
+ return -1;
+ }
+ break;
+ }
+
+ if (i >= SPI_RETRY) {
+ printk(BIOS_ERR, "SPI ERROR: Timeout\n");
+ return -1;
+ }
+
+ /* Read the data */
+ for (i = 0; i < size; i+=sizeof(u32)) {
+ if (size-i >= 4) {
+ /* reading >= dword */
+ *ptr32++ = RCBA32(SPIBAR_FDATA(i/sizeof(u32)));
+ } else {
+ /* reading < dword */
+ u8 j, *ptr8 = (u8*)ptr32;
+ u32 temp = RCBA32(SPIBAR_FDATA(i/sizeof(u32)));
+ for (j = 0; j < (size-i); j++) {
+ *ptr8++ = temp & 0xff;
+ temp >>= 8;
+ }
+ }
+ }
+
+ return size;
+}
+
+int early_spi_read(u32 offset, u32 size, u8 *buffer)
+{
+ u32 current = 0;
+
+ while (size > 0) {
+ u8 count = (size < 64) ? size : 64;
+ if (early_spi_read_block(offset + current, count,
+ buffer + current) < 0)
+ return -1;
+ size -= count;
+ current += count;
+ }
+
+ return 0;
+}
diff --git a/src/southbridge/intel/lynxpoint/early_usb.c b/src/southbridge/intel/lynxpoint/early_usb.c
new file mode 100644
index 0000000..b2e0091
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/early_usb.c
@@ -0,0 +1,57 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <console/console.h>
+#include <device/pci_ids.h>
+#include <device/pci_def.h>
+#include "pch.h"
+
+#define PCH_EHCI1_TEMP_BAR0 0xe8000000
+#define PCH_EHCI2_TEMP_BAR0 0xe8000400
+
+/*
+ * Setup USB controller MMIO BAR to prevent the
+ * reference code from resetting the controller.
+ *
+ * The BAR will be re-assigned during device
+ * enumeration so these are only temporary.
+ */
+void enable_usb_bar(void)
+{
+ device_t usb0 = PCH_EHCI1_DEV;
+ device_t usb1 = PCH_EHCI2_DEV;
+ u32 cmd;
+
+ /* USB Controller 1 */
+ pci_write_config32(usb0, PCI_BASE_ADDRESS_0,
+ PCH_EHCI1_TEMP_BAR0);
+ cmd = pci_read_config32(usb0, PCI_COMMAND);
+ cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_write_config32(usb0, PCI_COMMAND, cmd);
+
+ /* USB Controller 1 */
+ pci_write_config32(usb1, PCI_BASE_ADDRESS_0,
+ PCH_EHCI1_TEMP_BAR0);
+ cmd = pci_read_config32(usb1, PCI_COMMAND);
+ cmd |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_write_config32(usb1, PCI_COMMAND, cmd);
+}
diff --git a/src/southbridge/intel/lynxpoint/elog.c b/src/southbridge/intel/lynxpoint/elog.c
new file mode 100644
index 0000000..09dfcdb
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/elog.c
@@ -0,0 +1,114 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2012 The ChromiumOS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA, 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <arch/acpi.h>
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ops.h>
+#include <stdint.h>
+#include <string.h>
+#include <elog.h>
+#include "pch.h"
+
+void pch_log_state(void)
+{
+ u16 pm1_sts, gen_pmcon_3, tco2_sts;
+ u32 gpe0_sts, gpe0_en;
+ u8 gen_pmcon_2;
+ int i;
+ struct device *lpc = dev_find_slot(0, PCI_DEVFN(0x1f, 0));
+ if (!lpc)
+ return;
+
+ pm1_sts = inw(DEFAULT_PMBASE + PM1_STS);
+ gpe0_sts = inl(DEFAULT_PMBASE + GPE0_STS);
+ gpe0_en = inl(DEFAULT_PMBASE + GPE0_EN);
+ tco2_sts = inw(DEFAULT_PMBASE + TCO2_STS);
+ gen_pmcon_2 = pci_read_config8(lpc, GEN_PMCON_2);
+ gen_pmcon_3 = pci_read_config16(lpc, GEN_PMCON_3);
+
+ /* PWR_FLR Power Failure */
+ if (gen_pmcon_2 & (1 << 0))
+ elog_add_event(ELOG_TYPE_POWER_FAIL);
+
+ /* SUS Well Power Failure */
+ if (gen_pmcon_3 & (1 << 14))
+ elog_add_event(ELOG_TYPE_SUS_POWER_FAIL);
+
+ /* SYS_PWROK Failure */
+ if (gen_pmcon_2 & (1 << 1))
+ elog_add_event(ELOG_TYPE_SYS_PWROK_FAIL);
+
+ /* PWROK Failure */
+ if (gen_pmcon_2 & (1 << 0))
+ elog_add_event(ELOG_TYPE_PWROK_FAIL);
+
+ /* Second TCO Timeout */
+ if (tco2_sts & (1 << 1))
+ elog_add_event(ELOG_TYPE_TCO_RESET);
+
+ /* Power Button Override */
+ if (pm1_sts & (1 << 11))
+ elog_add_event(ELOG_TYPE_POWER_BUTTON_OVERRIDE);
+
+ /* System Reset Status (reset button pushed) */
+ if (gen_pmcon_2 & (1 << 4))
+ elog_add_event(ELOG_TYPE_RESET_BUTTON);
+
+ /* General Reset Status */
+ if (gen_pmcon_3 & (1 << 9))
+ elog_add_event(ELOG_TYPE_SYSTEM_RESET);
+
+ /* ACPI Wake */
+ if (pm1_sts & (1 << 15))
+ elog_add_event_byte(ELOG_TYPE_ACPI_WAKE,
+ acpi_slp_type == 3 ? 3 : 5);
+
+ /*
+ * Wake sources
+ */
+
+ /* RTC */
+ if (pm1_sts & (1 << 10))
+ elog_add_event_wake(ELOG_WAKE_SOURCE_RTC, 0);
+
+ /* PCI Express (TODO: determine wake device) */
+ if (pm1_sts & (1 << 14))
+ elog_add_event_wake(ELOG_WAKE_SOURCE_PCIE, 0);
+
+ /* PME (TODO: determine wake device) */
+ if (gpe0_sts & (1 << 13))
+ elog_add_event_wake(ELOG_WAKE_SOURCE_PME, 0);
+
+ /* Internal PME (TODO: determine wake device) */
+ if (gpe0_sts & (1 << 13))
+ elog_add_event_wake(ELOG_WAKE_SOURCE_PME_INTERNAL, 0);
+
+ /* GPIO 0-15 */
+ for (i = 0; i < 16; i++) {
+ if ((gpe0_sts & (1 << (16+i))) && (gpe0_en & (1 << (16+i))))
+ elog_add_event_wake(ELOG_WAKE_SOURCE_GPIO, i);
+ }
+
+ /* SMBUS Wake */
+ if (gpe0_sts & (1 << 7))
+ elog_add_event_wake(ELOG_WAKE_SOURCE_SMBUS, 0);
+}
diff --git a/src/southbridge/intel/lynxpoint/finalize.c b/src/southbridge/intel/lynxpoint/finalize.c
new file mode 100644
index 0000000..796633d
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/finalize.c
@@ -0,0 +1,66 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2012 The Chromium OS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <console/post_codes.h>
+#include <northbridge/intel/haswell/pcie_config.c>
+#include <spi-generic.h>
+#include "pch.h"
+
+void intel_pch_finalize_smm(void)
+{
+ /* Set SPI opcode menu */
+ RCBA16(0x3894) = SPI_OPPREFIX;
+ RCBA16(0x3896) = SPI_OPTYPE;
+ RCBA32(0x3898) = SPI_OPMENU_LOWER;
+ RCBA32(0x389c) = SPI_OPMENU_UPPER;
+
+ /* Lock SPIBAR */
+ RCBA32_OR(0x3804, (1 << 15));
+
+#if CONFIG_SPI_FLASH_SMM
+ /* Re-init SPI driver to handle locked BAR */
+ spi_init();
+#endif
+
+ /* TCLOCKDN: TC Lockdown */
+ RCBA32_OR(0x0050, (1 << 31));
+
+ /* BIOS Interface Lockdown */
+ RCBA32_OR(0x3410, (1 << 0));
+
+ /* Function Disable SUS Well Lockdown */
+ RCBA_AND_OR(8, 0x3420, ~0U, (1 << 7));
+
+ /* Global SMI Lock */
+ pcie_or_config16(PCH_LPC_DEV, 0xa0, 1 << 4);
+
+ /* GEN_PMCON Lock */
+ pcie_or_config8(PCH_LPC_DEV, 0xa6, (1 << 1) | (1 << 2));
+
+ /* R/WO registers */
+ RCBA32(0x21a4) = RCBA32(0x21a4);
+ pcie_write_config32(PCI_DEV(0, 27, 0), 0x74,
+ pcie_read_config32(PCI_DEV(0, 27, 0), 0x74));
+
+ /* Indicate finalize step with post code */
+ outb(POST_OS_BOOT, 0x80);
+}
diff --git a/src/southbridge/intel/lynxpoint/gpio.c b/src/southbridge/intel/lynxpoint/gpio.c
new file mode 100644
index 0000000..25eda9a
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/gpio.c
@@ -0,0 +1,101 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2011 The Chromium OS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <stdint.h>
+#include <string.h>
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+
+#include "pch.h"
+#include "gpio.h"
+
+#define MAX_GPIO_NUMBER 75 /* zero based */
+
+void setup_pch_gpios(const struct pch_gpio_map *gpio)
+{
+ u16 gpiobase = pci_read_config16(PCH_LPC_DEV, GPIO_BASE) & 0xfffc;
+
+ /* GPIO Set 1 */
+ if (gpio->set1.level)
+ outl(*((u32*)gpio->set1.level), gpiobase + GP_LVL);
+ if (gpio->set1.mode)
+ outl(*((u32*)gpio->set1.mode), gpiobase + GPIO_USE_SEL);
+ if (gpio->set1.direction)
+ outl(*((u32*)gpio->set1.direction), gpiobase + GP_IO_SEL);
+ if (gpio->set1.reset)
+ outl(*((u32*)gpio->set1.reset), gpiobase + GP_RST_SEL1);
+ if (gpio->set1.invert)
+ outl(*((u32*)gpio->set1.invert), gpiobase + GPI_INV);
+ if (gpio->set1.blink)
+ outl(*((u32*)gpio->set1.blink), gpiobase + GPO_BLINK);
+
+ /* GPIO Set 2 */
+ if (gpio->set2.level)
+ outl(*((u32*)gpio->set2.level), gpiobase + GP_LVL2);
+ if (gpio->set2.mode)
+ outl(*((u32*)gpio->set2.mode), gpiobase + GPIO_USE_SEL2);
+ if (gpio->set2.direction)
+ outl(*((u32*)gpio->set2.direction), gpiobase + GP_IO_SEL2);
+ if (gpio->set2.reset)
+ outl(*((u32*)gpio->set2.reset), gpiobase + GP_RST_SEL2);
+
+ /* GPIO Set 3 */
+ if (gpio->set3.level)
+ outl(*((u32*)gpio->set3.level), gpiobase + GP_LVL3);
+ if (gpio->set3.mode)
+ outl(*((u32*)gpio->set3.mode), gpiobase + GPIO_USE_SEL3);
+ if (gpio->set3.direction)
+ outl(*((u32*)gpio->set3.direction), gpiobase + GP_IO_SEL3);
+ if (gpio->set3.reset)
+ outl(*((u32*)gpio->set3.reset), gpiobase + GP_RST_SEL3);
+}
+
+int get_gpio(int gpio_num)
+{
+ static const int gpio_reg_offsets[] = {0xc, 0x38, 0x48};
+ u16 gpio_base = pci_read_config16(PCH_LPC_DEV, GPIO_BASE) & 0xfffc;
+ int index, bit;
+
+ if (gpio_num > MAX_GPIO_NUMBER)
+ return 0; /* Just ignore wrong gpio numbers. */
+
+ index = gpio_num / 32;
+ bit = gpio_num % 32;
+
+ return (inl(gpio_base + gpio_reg_offsets[index]) >> bit) & 1;
+}
+
+/*
+ * get a number comprised of multiple GPIO values. gpio_num_array points to
+ * the array of gpio pin numbers to scan, terminated by -1.
+ */
+unsigned get_gpios(const int *gpio_num_array)
+{
+ int gpio;
+ unsigned bitmask = 1;
+ unsigned vector = 0;
+
+ while (bitmask &&
+ ((gpio = *gpio_num_array++) != -1)) {
+ if (get_gpio(gpio))
+ vector |= bitmask;
+ bitmask <<= 1;
+ }
+ return vector;
+}
diff --git a/src/southbridge/intel/lynxpoint/gpio.h b/src/southbridge/intel/lynxpoint/gpio.h
new file mode 100644
index 0000000..a6f99f6
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/gpio.h
@@ -0,0 +1,161 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2011 The Chromium OS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef INTEL_LYNXPOINT_GPIO_H
+#define INTEL_LYNXPOINT_GPIO_H
+
+#define GPIO_MODE_NATIVE 0
+#define GPIO_MODE_GPIO 1
+#define GPIO_MODE_NONE 1
+
+#define GPIO_DIR_OUTPUT 0
+#define GPIO_DIR_INPUT 1
+
+#define GPIO_NO_INVERT 0
+#define GPIO_INVERT 1
+
+#define GPIO_LEVEL_LOW 0
+#define GPIO_LEVEL_HIGH 1
+
+#define GPIO_NO_BLINK 0
+#define GPIO_BLINK 1
+
+#define GPIO_RESET_PWROK 0
+#define GPIO_RESET_RSMRST 1
+
+struct pch_gpio_set1 {
+ u32 gpio0 : 1;
+ u32 gpio1 : 1;
+ u32 gpio2 : 1;
+ u32 gpio3 : 1;
+ u32 gpio4 : 1;
+ u32 gpio5 : 1;
+ u32 gpio6 : 1;
+ u32 gpio7 : 1;
+ u32 gpio8 : 1;
+ u32 gpio9 : 1;
+ u32 gpio10 : 1;
+ u32 gpio11 : 1;
+ u32 gpio12 : 1;
+ u32 gpio13 : 1;
+ u32 gpio14 : 1;
+ u32 gpio15 : 1;
+ u32 gpio16 : 1;
+ u32 gpio17 : 1;
+ u32 gpio18 : 1;
+ u32 gpio19 : 1;
+ u32 gpio20 : 1;
+ u32 gpio21 : 1;
+ u32 gpio22 : 1;
+ u32 gpio23 : 1;
+ u32 gpio24 : 1;
+ u32 gpio25 : 1;
+ u32 gpio26 : 1;
+ u32 gpio27 : 1;
+ u32 gpio28 : 1;
+ u32 gpio29 : 1;
+ u32 gpio30 : 1;
+ u32 gpio31 : 1;
+} __attribute__ ((packed));
+
+struct pch_gpio_set2 {
+ u32 gpio32 : 1;
+ u32 gpio33 : 1;
+ u32 gpio34 : 1;
+ u32 gpio35 : 1;
+ u32 gpio36 : 1;
+ u32 gpio37 : 1;
+ u32 gpio38 : 1;
+ u32 gpio39 : 1;
+ u32 gpio40 : 1;
+ u32 gpio41 : 1;
+ u32 gpio42 : 1;
+ u32 gpio43 : 1;
+ u32 gpio44 : 1;
+ u32 gpio45 : 1;
+ u32 gpio46 : 1;
+ u32 gpio47 : 1;
+ u32 gpio48 : 1;
+ u32 gpio49 : 1;
+ u32 gpio50 : 1;
+ u32 gpio51 : 1;
+ u32 gpio52 : 1;
+ u32 gpio53 : 1;
+ u32 gpio54 : 1;
+ u32 gpio55 : 1;
+ u32 gpio56 : 1;
+ u32 gpio57 : 1;
+ u32 gpio58 : 1;
+ u32 gpio59 : 1;
+ u32 gpio60 : 1;
+ u32 gpio61 : 1;
+ u32 gpio62 : 1;
+ u32 gpio63 : 1;
+} __attribute__ ((packed));
+
+struct pch_gpio_set3 {
+ u32 gpio64 : 1;
+ u32 gpio65 : 1;
+ u32 gpio66 : 1;
+ u32 gpio67 : 1;
+ u32 gpio68 : 1;
+ u32 gpio69 : 1;
+ u32 gpio70 : 1;
+ u32 gpio71 : 1;
+ u32 gpio72 : 1;
+ u32 gpio73 : 1;
+ u32 gpio74 : 1;
+ u32 gpio75 : 1;
+} __attribute__ ((packed));
+
+struct pch_gpio_map {
+ struct {
+ const struct pch_gpio_set1 *mode;
+ const struct pch_gpio_set1 *direction;
+ const struct pch_gpio_set1 *level;
+ const struct pch_gpio_set1 *reset;
+ const struct pch_gpio_set1 *invert;
+ const struct pch_gpio_set1 *blink;
+ } set1;
+ struct {
+ const struct pch_gpio_set2 *mode;
+ const struct pch_gpio_set2 *direction;
+ const struct pch_gpio_set2 *level;
+ const struct pch_gpio_set2 *reset;
+ } set2;
+ struct {
+ const struct pch_gpio_set3 *mode;
+ const struct pch_gpio_set3 *direction;
+ const struct pch_gpio_set3 *level;
+ const struct pch_gpio_set3 *reset;
+ } set3;
+};
+
+/* Configure GPIOs with mainboard provided settings */
+void setup_pch_gpios(const struct pch_gpio_map *gpio);
+
+/* get GPIO pin value */
+int get_gpio(int gpio_num);
+/*
+ * get a number comprised of multiple GPIO values. gpio_num_array points to
+ * the array of gpio pin numbers to scan, terminated by -1.
+ */
+unsigned get_gpios(const int *gpio_num_array);
+
+#endif
diff --git a/src/southbridge/intel/lynxpoint/lpc.c b/src/southbridge/intel/lynxpoint/lpc.c
new file mode 100644
index 0000000..55c2f5a
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/lpc.c
@@ -0,0 +1,667 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <pc80/mc146818rtc.h>
+#include <pc80/isa-dma.h>
+#include <pc80/i8259.h>
+#include <arch/io.h>
+#include <arch/ioapic.h>
+#include <arch/acpi.h>
+#include <cpu/cpu.h>
+#include <elog.h>
+#include "pch.h"
+
+#define NMI_OFF 0
+
+#define ENABLE_ACPI_MODE_IN_COREBOOT 0
+#define TEST_SMM_FLASH_LOCKDOWN 0
+
+typedef struct southbridge_intel_lynxpoint_config config_t;
+
+static void pch_enable_apic(struct device *dev)
+{
+ int i;
+ u32 reg32;
+ volatile u32 *ioapic_index = (volatile u32 *)(IO_APIC_ADDR);
+ volatile u32 *ioapic_data = (volatile u32 *)(IO_APIC_ADDR + 0x10);
+
+ /* Enable ACPI I/O and power management.
+ * Set SCI IRQ to IRQ9
+ */
+ pci_write_config8(dev, ACPI_CNTL, 0x80);
+
+ *ioapic_index = 0;
+ *ioapic_data = (1 << 25);
+
+ /* affirm full set of redirection table entries ("write once") */
+ *ioapic_index = 1;
+ reg32 = *ioapic_data;
+ *ioapic_index = 1;
+ *ioapic_data = reg32;
+
+ *ioapic_index = 0;
+ reg32 = *ioapic_data;
+ printk(BIOS_DEBUG, "Southbridge APIC ID = %x\n", (reg32 >> 24) & 0x0f);
+ if (reg32 != (1 << 25))
+ die("APIC Error\n");
+
+ printk(BIOS_SPEW, "Dumping IOAPIC registers\n");
+ for (i=0; i<3; i++) {
+ *ioapic_index = i;
+ printk(BIOS_SPEW, " reg 0x%04x:", i);
+ reg32 = *ioapic_data;
+ printk(BIOS_SPEW, " 0x%08x\n", reg32);
+ }
+
+ *ioapic_index = 3; /* Select Boot Configuration register. */
+ *ioapic_data = 1; /* Use Processor System Bus to deliver interrupts. */
+}
+
+static void pch_enable_serial_irqs(struct device *dev)
+{
+ /* Set packet length and toggle silent mode bit for one frame. */
+ pci_write_config8(dev, SERIRQ_CNTL,
+ (1 << 7) | (1 << 6) | ((21 - 17) << 2) | (0 << 0));
+#if !CONFIG_SERIRQ_CONTINUOUS_MODE
+ pci_write_config8(dev, SERIRQ_CNTL,
+ (1 << 7) | (0 << 6) | ((21 - 17) << 2) | (0 << 0));
+#endif
+}
+
+/* PIRQ[n]_ROUT[3:0] - PIRQ Routing Control
+ * 0x00 - 0000 = Reserved
+ * 0x01 - 0001 = Reserved
+ * 0x02 - 0010 = Reserved
+ * 0x03 - 0011 = IRQ3
+ * 0x04 - 0100 = IRQ4
+ * 0x05 - 0101 = IRQ5
+ * 0x06 - 0110 = IRQ6
+ * 0x07 - 0111 = IRQ7
+ * 0x08 - 1000 = Reserved
+ * 0x09 - 1001 = IRQ9
+ * 0x0A - 1010 = IRQ10
+ * 0x0B - 1011 = IRQ11
+ * 0x0C - 1100 = IRQ12
+ * 0x0D - 1101 = Reserved
+ * 0x0E - 1110 = IRQ14
+ * 0x0F - 1111 = IRQ15
+ * PIRQ[n]_ROUT[7] - PIRQ Routing Control
+ * 0x80 - The PIRQ is not routed.
+ */
+
+static void pch_pirq_init(device_t dev)
+{
+ device_t irq_dev;
+ /* Get the chip configuration */
+ config_t *config = dev->chip_info;
+
+ pci_write_config8(dev, PIRQA_ROUT, config->pirqa_routing);
+ pci_write_config8(dev, PIRQB_ROUT, config->pirqb_routing);
+ pci_write_config8(dev, PIRQC_ROUT, config->pirqc_routing);
+ pci_write_config8(dev, PIRQD_ROUT, config->pirqd_routing);
+
+ pci_write_config8(dev, PIRQE_ROUT, config->pirqe_routing);
+ pci_write_config8(dev, PIRQF_ROUT, config->pirqf_routing);
+ pci_write_config8(dev, PIRQG_ROUT, config->pirqg_routing);
+ pci_write_config8(dev, PIRQH_ROUT, config->pirqh_routing);
+
+ /* Eric Biederman once said we should let the OS do this.
+ * I am not so sure anymore he was right.
+ */
+
+ for(irq_dev = all_devices; irq_dev; irq_dev = irq_dev->next) {
+ u8 int_pin=0, int_line=0;
+
+ if (!irq_dev->enabled || irq_dev->path.type != DEVICE_PATH_PCI)
+ continue;
+
+ int_pin = pci_read_config8(irq_dev, PCI_INTERRUPT_PIN);
+
+ switch (int_pin) {
+ case 1: /* INTA# */ int_line = config->pirqa_routing; break;
+ case 2: /* INTB# */ int_line = config->pirqb_routing; break;
+ case 3: /* INTC# */ int_line = config->pirqc_routing; break;
+ case 4: /* INTD# */ int_line = config->pirqd_routing; break;
+ }
+
+ if (!int_line)
+ continue;
+
+ pci_write_config8(irq_dev, PCI_INTERRUPT_LINE, int_line);
+ }
+}
+
+static void pch_gpi_routing(device_t dev)
+{
+ /* Get the chip configuration */
+ config_t *config = dev->chip_info;
+ u32 reg32 = 0;
+
+ /* An array would be much nicer here, or some
+ * other method of doing this.
+ */
+ reg32 |= (config->gpi0_routing & 0x03) << 0;
+ reg32 |= (config->gpi1_routing & 0x03) << 2;
+ reg32 |= (config->gpi2_routing & 0x03) << 4;
+ reg32 |= (config->gpi3_routing & 0x03) << 6;
+ reg32 |= (config->gpi4_routing & 0x03) << 8;
+ reg32 |= (config->gpi5_routing & 0x03) << 10;
+ reg32 |= (config->gpi6_routing & 0x03) << 12;
+ reg32 |= (config->gpi7_routing & 0x03) << 14;
+ reg32 |= (config->gpi8_routing & 0x03) << 16;
+ reg32 |= (config->gpi9_routing & 0x03) << 18;
+ reg32 |= (config->gpi10_routing & 0x03) << 20;
+ reg32 |= (config->gpi11_routing & 0x03) << 22;
+ reg32 |= (config->gpi12_routing & 0x03) << 24;
+ reg32 |= (config->gpi13_routing & 0x03) << 26;
+ reg32 |= (config->gpi14_routing & 0x03) << 28;
+ reg32 |= (config->gpi15_routing & 0x03) << 30;
+
+ pci_write_config32(dev, 0xb8, reg32);
+}
+
+static void pch_power_options(device_t dev)
+{
+ u8 reg8;
+ u16 reg16, pmbase;
+ u32 reg32;
+ const char *state;
+ /* Get the chip configuration */
+ config_t *config = dev->chip_info;
+
+ int pwr_on=CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+ int nmi_option;
+
+ /* Which state do we want to goto after g3 (power restored)?
+ * 0 == S0 Full On
+ * 1 == S5 Soft Off
+ *
+ * If the option is not existent (Laptops), use Kconfig setting.
+ */
+ get_option(&pwr_on, "power_on_after_fail");
+
+ reg16 = pci_read_config16(dev, GEN_PMCON_3);
+ reg16 &= 0xfffe;
+ switch (pwr_on) {
+ case MAINBOARD_POWER_OFF:
+ reg16 |= 1;
+ state = "off";
+ break;
+ case MAINBOARD_POWER_ON:
+ reg16 &= ~1;
+ state = "on";
+ break;
+ case MAINBOARD_POWER_KEEP:
+ reg16 &= ~1;
+ state = "state keep";
+ break;
+ default:
+ state = "undefined";
+ }
+
+ reg16 &= ~(3 << 4); /* SLP_S4# Assertion Stretch 4s */
+ reg16 |= (1 << 3); /* SLP_S4# Assertion Stretch Enable */
+
+ reg16 &= ~(1 << 10);
+ reg16 |= (1 << 11); /* SLP_S3# Min Assertion Width 50ms */
+
+ reg16 |= (1 << 12); /* Disable SLP stretch after SUS well */
+
+ pci_write_config16(dev, GEN_PMCON_3, reg16);
+ printk(BIOS_INFO, "Set power %s after power failure.\n", state);
+
+ /* Set up NMI on errors. */
+ reg8 = inb(0x61);
+ reg8 &= 0x0f; /* Higher Nibble must be 0 */
+ reg8 &= ~(1 << 3); /* IOCHK# NMI Enable */
+ // reg8 &= ~(1 << 2); /* PCI SERR# Enable */
+ reg8 |= (1 << 2); /* PCI SERR# Disable for now */
+ outb(reg8, 0x61);
+
+ reg8 = inb(0x70);
+ nmi_option = NMI_OFF;
+ get_option(&nmi_option, "nmi");
+ if (nmi_option) {
+ printk(BIOS_INFO, "NMI sources enabled.\n");
+ reg8 &= ~(1 << 7); /* Set NMI. */
+ } else {
+ printk(BIOS_INFO, "NMI sources disabled.\n");
+ reg8 |= ( 1 << 7); /* Can't mask NMI from PCI-E and NMI_NOW */
+ }
+ outb(reg8, 0x70);
+
+ /* Enable CPU_SLP# and Intel Speedstep, set SMI# rate down */
+ reg16 = pci_read_config16(dev, GEN_PMCON_1);
+ reg16 &= ~(3 << 0); // SMI# rate 1 minute
+ reg16 &= ~(1 << 10); // Disable BIOS_PCI_EXP_EN for native PME
+#if DEBUG_PERIODIC_SMIS
+ /* Set DEBUG_PERIODIC_SMIS in pch.h to debug using
+ * periodic SMIs.
+ */
+ reg16 |= (3 << 0); // Periodic SMI every 8s
+#endif
+ pci_write_config16(dev, GEN_PMCON_1, reg16);
+
+ // Set the board's GPI routing.
+ pch_gpi_routing(dev);
+
+ pmbase = pci_read_config16(dev, 0x40) & 0xfffe;
+
+ outl(config->gpe0_en, pmbase + GPE0_EN);
+ outw(config->alt_gp_smi_en, pmbase + ALT_GP_SMI_EN);
+
+ /* Set up power management block and determine sleep mode */
+ reg32 = inl(pmbase + 0x04); // PM1_CNT
+ reg32 &= ~(7 << 10); // SLP_TYP
+ reg32 |= (1 << 0); // SCI_EN
+ outl(reg32, pmbase + 0x04);
+
+ /* Clear magic status bits to prevent unexpected wake */
+ reg32 = RCBA32(0x3310);
+ reg32 |= (1 << 4)|(1 << 5)|(1 << 0);
+ RCBA32(0x3310) = reg32;
+
+ reg32 = RCBA32(0x3f02);
+ reg32 &= ~0xf;
+ RCBA32(0x3f02) = reg32;
+}
+
+static void pch_rtc_init(struct device *dev)
+{
+ u8 reg8;
+ int rtc_failed;
+
+ reg8 = pci_read_config8(dev, GEN_PMCON_3);
+ rtc_failed = reg8 & RTC_BATTERY_DEAD;
+ if (rtc_failed) {
+ reg8 &= ~RTC_BATTERY_DEAD;
+ pci_write_config8(dev, GEN_PMCON_3, reg8);
+#if CONFIG_ELOG
+ elog_add_event(ELOG_TYPE_RTC_RESET);
+#endif
+ }
+ printk(BIOS_DEBUG, "rtc_failed = 0x%x\n", rtc_failed);
+
+ rtc_init(rtc_failed);
+}
+
+/* CougarPoint PCH Power Management init */
+#if 0
+static void cpt_pm_init(struct device *dev)
+{
+ printk(BIOS_DEBUG, "CougarPoint PM init\n");
+ pci_write_config8(dev, 0xa9, 0x47);
+ RCBA32_AND_OR(0x2238, ~0UL, (1 << 6)|(1 << 0));
+ RCBA32_AND_OR(0x228c, ~0UL, (1 << 0));
+ RCBA16_AND_OR(0x1100, ~0UL, (1 << 13)|(1 << 14));
+ RCBA16_AND_OR(0x0900, ~0UL, (1 << 14));
+ RCBA32(0x2304) = 0xc0388400;
+ RCBA32_AND_OR(0x2314, ~0UL, (1 << 5)|(1 << 18));
+ RCBA32_AND_OR(0x2320, ~0UL, (1 << 15)|(1 << 1));
+ RCBA32_AND_OR(0x3314, ~0x1f, 0xf);
+ RCBA32(0x3318) = 0x050f0000;
+ RCBA32(0x3324) = 0x04000000;
+ RCBA32_AND_OR(0x3340, ~0UL, 0xfffff);
+ RCBA32_AND_OR(0x3344, ~0UL, (1 << 1));
+ RCBA32(0x3360) = 0x0001c000;
+ RCBA32(0x3368) = 0x00061100;
+ RCBA32(0x3378) = 0x7f8fdfff;
+ RCBA32(0x337c) = 0x000003fc;
+ RCBA32(0x3388) = 0x00001000;
+ RCBA32(0x3390) = 0x0001c000;
+ RCBA32(0x33a0) = 0x00000800;
+ RCBA32(0x33b0) = 0x00001000;
+ RCBA32(0x33c0) = 0x00093900;
+ RCBA32(0x33cc) = 0x24653002;
+ RCBA32(0x33d0) = 0x062108fe;
+ RCBA32_AND_OR(0x33d4, 0xf000f000, 0x00670060);
+ RCBA32(0x3a28) = 0x01010000;
+ RCBA32(0x3a2c) = 0x01010404;
+ RCBA32(0x3a80) = 0x01041041;
+ RCBA32_AND_OR(0x3a84, ~0x0000ffff, 0x00001001);
+ RCBA32_AND_OR(0x3a84, ~0UL, (1 << 24)); /* SATA 2/3 disabled */
+ RCBA32_AND_OR(0x3a88, ~0UL, (1 << 0)); /* SATA 4/5 disabled */
+ RCBA32(0x3a6c) = 0x00000001;
+ RCBA32_AND_OR(0x2344, 0x00ffff00, 0xff00000c);
+ RCBA32_AND_OR(0x80c, ~(0xff << 20), 0x11 << 20);
+ RCBA32(0x33c8) = 0;
+ RCBA32_AND_OR(0x21b0, ~0UL, 0xf);
+}
+#endif
+
+static void enable_hpet(void)
+{
+ u32 reg32;
+
+ /* Move HPET to default address 0xfed00000 and enable it */
+ reg32 = RCBA32(HPTC);
+ reg32 |= (1 << 7); // HPET Address Enable
+ reg32 &= ~(3 << 0);
+ RCBA32(HPTC) = reg32;
+ /* Read it back to stick. It's affected by posted write syndrome. */
+ reg32 = RCBA32(HPTC);
+}
+
+static void enable_clock_gating(device_t dev)
+{
+ u32 reg32;
+ u16 reg16;
+
+ RCBA32_AND_OR(0x2234, ~0UL, 0xf);
+
+ reg16 = pci_read_config16(dev, GEN_PMCON_1);
+ reg16 |= (1 << 2) | (1 << 11);
+ pci_write_config16(dev, GEN_PMCON_1, reg16);
+
+ pch_iobp_update(0xEB007F07, ~0UL, (1 << 31));
+ pch_iobp_update(0xEB004000, ~0UL, (1 << 7));
+ pch_iobp_update(0xEC007F07, ~0UL, (1 << 31));
+ pch_iobp_update(0xEC004000, ~0UL, (1 << 7));
+
+ reg32 = RCBA32(CG);
+ reg32 |= (1 << 31);
+ reg32 |= (1 << 29) | (1 << 28);
+ reg32 |= (1 << 27) | (1 << 26) | (1 << 25) | (1 << 24);
+ reg32 |= (1 << 16);
+ reg32 |= (1 << 17);
+ reg32 |= (1 << 18);
+ reg32 |= (1 << 22);
+ reg32 |= (1 << 23);
+ reg32 &= ~(1 << 20);
+ reg32 |= (1 << 19);
+ reg32 |= (1 << 0);
+ reg32 |= (0xf << 1);
+ RCBA32(CG) = reg32;
+
+ RCBA32_OR(0x38c0, 0x7);
+ RCBA32_OR(0x36d4, 0x6680c004);
+ RCBA32_OR(0x3564, 0x3);
+}
+
+#if CONFIG_HAVE_SMI_HANDLER
+static void pch_lock_smm(struct device *dev)
+{
+#if TEST_SMM_FLASH_LOCKDOWN
+ u8 reg8;
+#endif
+
+ if (acpi_slp_type != 3) {
+#if ENABLE_ACPI_MODE_IN_COREBOOT
+ printk(BIOS_DEBUG, "Enabling ACPI via APMC:\n");
+ outb(0xe1, 0xb2); // Enable ACPI mode
+ printk(BIOS_DEBUG, "done.\n");
+#else
+ printk(BIOS_DEBUG, "Disabling ACPI via APMC:\n");
+ outb(0x1e, 0xb2); // Disable ACPI mode
+ printk(BIOS_DEBUG, "done.\n");
+#endif
+ }
+
+ /* Don't allow evil boot loaders, kernels, or
+ * userspace applications to deceive us:
+ */
+ smm_lock();
+
+#if TEST_SMM_FLASH_LOCKDOWN
+ /* Now try this: */
+ printk(BIOS_DEBUG, "Locking BIOS to RO... ");
+ reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */
+ printk(BIOS_DEBUG, " BLE: %s; BWE: %s\n", (reg8&2)?"on":"off",
+ (reg8&1)?"rw":"ro");
+ reg8 &= ~(1 << 0); /* clear BIOSWE */
+ pci_write_config8(dev, 0xdc, reg8);
+ reg8 |= (1 << 1); /* set BLE */
+ pci_write_config8(dev, 0xdc, reg8);
+ printk(BIOS_DEBUG, "ok.\n");
+ reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */
+ printk(BIOS_DEBUG, " BLE: %s; BWE: %s\n", (reg8&2)?"on":"off",
+ (reg8&1)?"rw":"ro");
+
+ printk(BIOS_DEBUG, "Writing:\n");
+ *(volatile u8 *)0xfff00000 = 0x00;
+ printk(BIOS_DEBUG, "Testing:\n");
+ reg8 |= (1 << 0); /* set BIOSWE */
+ pci_write_config8(dev, 0xdc, reg8);
+
+ reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */
+ printk(BIOS_DEBUG, " BLE: %s; BWE: %s\n", (reg8&2)?"on":"off",
+ (reg8&1)?"rw":"ro");
+ printk(BIOS_DEBUG, "Done.\n");
+#endif
+}
+#endif
+
+static void pch_disable_smm_only_flashing(struct device *dev)
+{
+ u8 reg8;
+
+ printk(BIOS_SPEW, "Enabling BIOS updates outside of SMM... ");
+ reg8 = pci_read_config8(dev, 0xdc); /* BIOS_CNTL */
+ reg8 &= ~(1 << 5);
+ pci_write_config8(dev, 0xdc, reg8);
+}
+
+static void pch_fixups(struct device *dev)
+{
+ u8 gen_pmcon_2;
+
+ /* Indicate DRAM init done for MRC S3 to know it can resume */
+ gen_pmcon_2 = pci_read_config8(dev, GEN_PMCON_2);
+ gen_pmcon_2 |= (1 << 7);
+ pci_write_config8(dev, GEN_PMCON_2, gen_pmcon_2);
+
+ /*
+ * Enable DMI ASPM in the PCH
+ */
+ RCBA32_AND_OR(0x2304, ~(1 << 10), 0);
+ RCBA32_OR(0x21a4, (1 << 11)|(1 << 10));
+ RCBA32_OR(0x21a8, 0x3);
+}
+
+static void pch_decode_init(struct device *dev)
+{
+ config_t *config = dev->chip_info;
+
+ printk(BIOS_DEBUG, "pch_decode_init\n");
+
+ pci_write_config32(dev, LPC_GEN1_DEC, config->gen1_dec);
+ pci_write_config32(dev, LPC_GEN2_DEC, config->gen2_dec);
+ pci_write_config32(dev, LPC_GEN3_DEC, config->gen3_dec);
+ pci_write_config32(dev, LPC_GEN4_DEC, config->gen4_dec);
+}
+
+static void lpc_init(struct device *dev)
+{
+ printk(BIOS_DEBUG, "pch: lpc_init\n");
+
+ /* Set the value for PCI command register. */
+ pci_write_config16(dev, PCI_COMMAND, 0x000f);
+
+ /* IO APIC initialization. */
+ pch_enable_apic(dev);
+
+ pch_enable_serial_irqs(dev);
+
+ /* Setup the PIRQ. */
+ pch_pirq_init(dev);
+
+ /* Setup power options. */
+ pch_power_options(dev);
+
+ /* Initialize power management */
+ switch (pch_silicon_type()) {
+ default:
+ printk(BIOS_ERR, "Unknown Chipset: 0x%04x\n", dev->device);
+ }
+
+ /* Set the state of the GPIO lines. */
+ //gpio_init(dev);
+
+ /* Initialize the real time clock. */
+ pch_rtc_init(dev);
+
+ /* Initialize ISA DMA. */
+ isa_dma_init();
+
+ /* Initialize the High Precision Event Timers, if present. */
+ enable_hpet();
+
+ /* Initialize Clock Gating */
+ enable_clock_gating(dev);
+
+ setup_i8259();
+
+ /* The OS should do this? */
+ /* Interrupt 9 should be level triggered (SCI) */
+ i8259_configure_irq_trigger(9, 1);
+
+ pch_disable_smm_only_flashing(dev);
+
+#if CONFIG_HAVE_SMI_HANDLER
+ pch_lock_smm(dev);
+#endif
+
+ pch_fixups(dev);
+}
+
+static void pch_lpc_read_resources(device_t dev)
+{
+ struct resource *res;
+ config_t *config = dev->chip_info;
+ u8 io_index = 0;
+
+ /* Get the normal PCI resources of this device. */
+ pci_dev_read_resources(dev);
+
+ /* Add an extra subtractive resource for both memory and I/O. */
+ res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0));
+ res->base = 0;
+ res->size = 0x1000;
+ res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE |
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+
+ res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0));
+ res->base = 0xff800000;
+ res->size = 0x00800000; /* 8 MB for flash */
+ res->flags = IORESOURCE_MEM | IORESOURCE_SUBTRACTIVE |
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+
+ res = new_resource(dev, 3); /* IOAPIC */
+ res->base = IO_APIC_ADDR;
+ res->size = 0x00001000;
+ res->flags = IORESOURCE_MEM | IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+
+ /* Set PCH IO decode ranges if required.*/
+ if ((config->gen1_dec & 0xFFFC) > 0x1000) {
+ res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0));
+ res->base = config->gen1_dec & 0xFFFC;
+ res->size = (config->gen1_dec >> 16) & 0xFC;
+ res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE |
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+ }
+
+ if ((config->gen2_dec & 0xFFFC) > 0x1000) {
+ res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0));
+ res->base = config->gen2_dec & 0xFFFC;
+ res->size = (config->gen2_dec >> 16) & 0xFC;
+ res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE |
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+ }
+
+ if ((config->gen3_dec & 0xFFFC) > 0x1000) {
+ res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0));
+ res->base = config->gen3_dec & 0xFFFC;
+ res->size = (config->gen3_dec >> 16) & 0xFC;
+ res->flags = IORESOURCE_IO | IORESOURCE_SUBTRACTIVE |
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+ }
+
+ if ((config->gen4_dec & 0xFFFC) > 0x1000) {
+ res = new_resource(dev, IOINDEX_SUBTRACTIVE(io_index++, 0));
+ res->base = config->gen4_dec & 0xFFFC;
+ res->size = (config->gen4_dec >> 16) & 0xFC;
+ res->flags = IORESOURCE_IO| IORESOURCE_SUBTRACTIVE |
+ IORESOURCE_ASSIGNED | IORESOURCE_FIXED;
+ }
+}
+
+static void pch_lpc_enable_resources(device_t dev)
+{
+ pch_decode_init(dev);
+ return pci_dev_enable_resources(dev);
+}
+
+static void pch_lpc_enable(device_t dev)
+{
+ /* Enable PCH Display Port */
+ RCBA16(DISPBDF) = 0x0010;
+ RCBA32_OR(FD2, PCH_ENABLE_DBDF);
+
+ pch_enable(dev);
+}
+
+static void set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ if (!vendor || !device) {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ pci_read_config32(dev, PCI_VENDOR_ID));
+ } else {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+ }
+}
+
+static struct pci_operations pci_ops = {
+ .set_subsystem = set_subsystem,
+};
+
+static struct device_operations device_ops = {
+ .read_resources = pch_lpc_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pch_lpc_enable_resources,
+ .init = lpc_init,
+ .enable = pch_lpc_enable,
+ .scan_bus = scan_static_bus,
+ .ops_pci = &pci_ops,
+};
+
+
+/* IDs for LPC device of Intel 6 Series Chipset, Intel 7 Series Chipset, and
+ * Intel C200 Series Chipset
+ */
+
+static const unsigned short pci_device_ids[] = { 0x1c46, 0x1c47, 0x1c49, 0x1c4a,
+ 0x1c4b, 0x1c4c, 0x1c4d, 0x1c4e,
+ 0x1c4f, 0x1c50, 0x1c52, 0x1c54,
+ 0x1e55, 0x1c56, 0x1e57, 0x1c5c,
+ 0x1e5d, 0x1e5e, 0x1e5f,
+ 0 };
+
+static const struct pci_driver pch_lpc __pci_driver = {
+ .ops = &device_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .devices = pci_device_ids,
+};
+
+
diff --git a/src/southbridge/intel/lynxpoint/me.h b/src/southbridge/intel/lynxpoint/me.h
new file mode 100644
index 0000000..aaeb24d
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/me.h
@@ -0,0 +1,373 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2011 The Chromium OS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _INTEL_ME_H
+#define _INTEL_ME_H
+
+#define ME_RETRY 100000 /* 1 second */
+#define ME_DELAY 10 /* 10 us */
+
+/*
+ * Management Engine PCI registers
+ */
+
+#define PCI_CPU_DEVICE PCI_DEV(0,0,0)
+#define PCI_CPU_MEBASE_L 0x70 /* Set by MRC */
+#define PCI_CPU_MEBASE_H 0x74 /* Set by MRC */
+
+#define PCI_ME_HFS 0x40
+#define ME_HFS_CWS_RESET 0
+#define ME_HFS_CWS_INIT 1
+#define ME_HFS_CWS_REC 2
+#define ME_HFS_CWS_NORMAL 5
+#define ME_HFS_CWS_WAIT 6
+#define ME_HFS_CWS_TRANS 7
+#define ME_HFS_CWS_INVALID 8
+#define ME_HFS_STATE_PREBOOT 0
+#define ME_HFS_STATE_M0_UMA 1
+#define ME_HFS_STATE_M3 4
+#define ME_HFS_STATE_M0 5
+#define ME_HFS_STATE_BRINGUP 6
+#define ME_HFS_STATE_ERROR 7
+#define ME_HFS_ERROR_NONE 0
+#define ME_HFS_ERROR_UNCAT 1
+#define ME_HFS_ERROR_IMAGE 3
+#define ME_HFS_ERROR_DEBUG 4
+#define ME_HFS_MODE_NORMAL 0
+#define ME_HFS_MODE_DEBUG 2
+#define ME_HFS_MODE_DIS 3
+#define ME_HFS_MODE_OVER_JMPR 4
+#define ME_HFS_MODE_OVER_MEI 5
+#define ME_HFS_BIOS_DRAM_ACK 1
+#define ME_HFS_ACK_NO_DID 0
+#define ME_HFS_ACK_RESET 1
+#define ME_HFS_ACK_PWR_CYCLE 2
+#define ME_HFS_ACK_S3 3
+#define ME_HFS_ACK_S4 4
+#define ME_HFS_ACK_S5 5
+#define ME_HFS_ACK_GBL_RESET 6
+#define ME_HFS_ACK_CONTINUE 7
+
+struct me_hfs {
+ u32 working_state: 4;
+ u32 mfg_mode: 1;
+ u32 fpt_bad: 1;
+ u32 operation_state: 3;
+ u32 fw_init_complete: 1;
+ u32 ft_bup_ld_flr: 1;
+ u32 update_in_progress: 1;
+ u32 error_code: 4;
+ u32 operation_mode: 4;
+ u32 reserved: 4;
+ u32 boot_options_present: 1;
+ u32 ack_data: 3;
+ u32 bios_msg_ack: 4;
+} __attribute__ ((packed));
+
+#define PCI_ME_UMA 0x44
+
+struct me_uma {
+ u32 size: 6;
+ u32 reserved_1: 10;
+ u32 valid: 1;
+ u32 reserved_0: 14;
+ u32 set_to_one: 1;
+} __attribute__ ((packed));
+
+#define PCI_ME_H_GS 0x4c
+#define ME_INIT_DONE 1
+#define ME_INIT_STATUS_SUCCESS 0
+#define ME_INIT_STATUS_NOMEM 1
+#define ME_INIT_STATUS_ERROR 2
+
+struct me_did {
+ u32 uma_base: 16;
+ u32 reserved: 8;
+ u32 status: 4;
+ u32 init_done: 4;
+} __attribute__ ((packed));
+
+#define PCI_ME_GMES 0x48
+#define ME_GMES_PHASE_ROM 0
+#define ME_GMES_PHASE_BUP 1
+#define ME_GMES_PHASE_UKERNEL 2
+#define ME_GMES_PHASE_POLICY 3
+#define ME_GMES_PHASE_MODULE 4
+#define ME_GMES_PHASE_UNKNOWN 5
+#define ME_GMES_PHASE_HOST 6
+
+struct me_gmes {
+ u32 bist_in_prog : 1;
+ u32 icc_prog_sts : 2;
+ u32 invoke_mebx : 1;
+ u32 cpu_replaced_sts : 1;
+ u32 mbp_rdy : 1;
+ u32 mfs_failure : 1;
+ u32 warm_rst_req_for_df : 1;
+ u32 cpu_replaced_valid : 1;
+ u32 reserved_1 : 2;
+ u32 fw_upd_ipu : 1;
+ u32 reserved_2 : 4;
+ u32 current_state: 8;
+ u32 current_pmevent: 4;
+ u32 progress_code: 4;
+} __attribute__ ((packed));
+
+#define PCI_ME_HERES 0xbc
+#define PCI_ME_EXT_SHA1 0x00
+#define PCI_ME_EXT_SHA256 0x02
+#define PCI_ME_HER(x) (0xc0+(4*(x)))
+
+struct me_heres {
+ u32 extend_reg_algorithm: 4;
+ u32 reserved: 26;
+ u32 extend_feature_present: 1;
+ u32 extend_reg_valid: 1;
+} __attribute__ ((packed));
+
+/*
+ * Management Engine MEI registers
+ */
+
+#define MEI_H_CB_WW 0x00
+#define MEI_H_CSR 0x04
+#define MEI_ME_CB_RW 0x08
+#define MEI_ME_CSR_HA 0x0c
+
+struct mei_csr {
+ u32 interrupt_enable: 1;
+ u32 interrupt_status: 1;
+ u32 interrupt_generate: 1;
+ u32 ready: 1;
+ u32 reset: 1;
+ u32 reserved: 3;
+ u32 buffer_read_ptr: 8;
+ u32 buffer_write_ptr: 8;
+ u32 buffer_depth: 8;
+} __attribute__ ((packed));
+
+#define MEI_ADDRESS_CORE 0x01
+#define MEI_ADDRESS_AMT 0x02
+#define MEI_ADDRESS_RESERVED 0x03
+#define MEI_ADDRESS_WDT 0x04
+#define MEI_ADDRESS_MKHI 0x07
+#define MEI_ADDRESS_ICC 0x08
+#define MEI_ADDRESS_THERMAL 0x09
+
+#define MEI_HOST_ADDRESS 0
+
+struct mei_header {
+ u32 client_address: 8;
+ u32 host_address: 8;
+ u32 length: 9;
+ u32 reserved: 6;
+ u32 is_complete: 1;
+} __attribute__ ((packed));
+
+#define MKHI_GROUP_ID_CBM 0x00
+#define MKHI_GROUP_ID_FWCAPS 0x03
+#define MKHI_GROUP_ID_MDES 0x08
+#define MKHI_GROUP_ID_GEN 0xff
+
+#define MKHI_GLOBAL_RESET 0x0b
+
+#define MKHI_FWCAPS_GET_RULE 0x02
+
+#define MKHI_MDES_ENABLE 0x09
+
+#define MKHI_GET_FW_VERSION 0x02
+#define MKHI_END_OF_POST 0x0c
+#define MKHI_FEATURE_OVERRIDE 0x14
+
+struct mkhi_header {
+ u32 group_id: 8;
+ u32 command: 7;
+ u32 is_response: 1;
+ u32 reserved: 8;
+ u32 result: 8;
+} __attribute__ ((packed));
+
+struct me_fw_version {
+ u16 code_minor;
+ u16 code_major;
+ u16 code_build_number;
+ u16 code_hot_fix;
+ u16 recovery_minor;
+ u16 recovery_major;
+ u16 recovery_build_number;
+ u16 recovery_hot_fix;
+} __attribute__ ((packed));
+
+
+#define HECI_EOP_STATUS_SUCCESS 0x0
+#define HECI_EOP_PERFORM_GLOBAL_RESET 0x1
+
+#define CBM_RR_GLOBAL_RESET 0x01
+
+#define GLOBAL_RESET_BIOS_MRC 0x01
+#define GLOBAL_RESET_BIOS_POST 0x02
+#define GLOBAL_RESET_MEBX 0x03
+
+struct me_global_reset {
+ u8 request_origin;
+ u8 reset_type;
+} __attribute__ ((packed));
+
+typedef enum {
+ ME_NORMAL_BIOS_PATH,
+ ME_S3WAKE_BIOS_PATH,
+ ME_ERROR_BIOS_PATH,
+ ME_RECOVERY_BIOS_PATH,
+ ME_DISABLE_BIOS_PATH,
+ ME_FIRMWARE_UPDATE_BIOS_PATH,
+} me_bios_path;
+
+/* Defined in me_status.c for both romstage and ramstage */
+void intel_me_status(struct me_hfs *hfs, struct me_gmes *gmes);
+
+#ifdef __PRE_RAM__
+void intel_early_me_status(void);
+int intel_early_me_init(void);
+int intel_early_me_uma_size(void);
+int intel_early_me_init_done(u8 status);
+#endif
+
+#ifdef __SMM__
+void intel_me_finalize_smm(void);
+void intel_me8_finalize_smm(void);
+#endif
+typedef struct {
+ u32 major_version : 16;
+ u32 minor_version : 16;
+ u32 hotfix_version : 16;
+ u32 build_version : 16;
+} __attribute__ ((packed)) mbp_fw_version_name;
+
+typedef struct {
+ u8 num_icc_profiles;
+ u8 icc_profile_soft_strap;
+ u8 icc_profile_index;
+ u8 reserved;
+ u32 register_lock_mask[3];
+} __attribute__ ((packed)) mbp_icc_profile;
+
+typedef struct {
+ u32 full_net : 1;
+ u32 std_net : 1;
+ u32 manageability : 1;
+ u32 small_business : 1;
+ u32 l3manageability : 1;
+ u32 intel_at : 1;
+ u32 intel_cls : 1;
+ u32 reserved : 3;
+ u32 intel_mpc : 1;
+ u32 icc_over_clocking : 1;
+ u32 pavp : 1;
+ u32 reserved_1 : 4;
+ u32 ipv6 : 1;
+ u32 kvm : 1;
+ u32 och : 1;
+ u32 vlan : 1;
+ u32 tls : 1;
+ u32 reserved_4 : 1;
+ u32 wlan : 1;
+ u32 reserved_5 : 8;
+} __attribute__ ((packed)) mefwcaps_sku;
+
+typedef struct {
+ u16 lock_state : 1;
+ u16 authenticate_module : 1;
+ u16 s3authentication : 1;
+ u16 flash_wear_out : 1;
+ u16 flash_variable_security : 1;
+ u16 wwan3gpresent : 1;
+ u16 wwan3goob : 1;
+ u16 reserved : 9;
+} __attribute__ ((packed)) tdt_state_flag;
+
+typedef struct {
+ u8 state;
+ u8 last_theft_trigger;
+ tdt_state_flag flags;
+} __attribute__ ((packed)) tdt_state_info;
+
+typedef struct {
+ u32 platform_target_usage_type : 4;
+ u32 platform_target_market_type : 2;
+ u32 super_sku : 1;
+ u32 reserved : 1;
+ u32 intel_me_fw_image_type : 4;
+ u32 platform_brand : 4;
+ u32 reserved_1 : 16;
+} __attribute__ ((packed)) platform_type_rule_data;
+
+typedef struct {
+ mefwcaps_sku fw_capabilities;
+ u8 available;
+} mbp_fw_caps;
+
+typedef struct {
+ u16 device_id;
+ u16 fuse_test_flags;
+ u32 umchid[4];
+} __attribute__ ((packed)) mbp_rom_bist_data;
+
+typedef struct {
+ u32 key[8];
+} mbp_platform_key;
+
+typedef struct {
+ platform_type_rule_data rule_data;
+ u8 available;
+} mbp_plat_type;
+
+typedef struct {
+ mbp_fw_version_name fw_version_name;
+ mbp_fw_caps fw_caps_sku;
+ mbp_rom_bist_data rom_bist_data;
+ mbp_platform_key platform_key;
+ mbp_plat_type fw_plat_type;
+ mbp_icc_profile icc_profile;
+ tdt_state_info at_state;
+ u32 mfsintegrity;
+} me_bios_payload;
+
+typedef struct {
+ u32 mbp_size : 8;
+ u32 num_entries : 8;
+ u32 rsvd : 16;
+} __attribute__ ((packed)) mbp_header;
+
+typedef struct {
+ u32 app_id : 8;
+ u32 item_id : 8;
+ u32 length : 8;
+ u32 rsvd : 8;
+} __attribute__ ((packed)) mbp_item_header;
+
+struct me_fwcaps {
+ u32 id;
+ u8 length;
+ mefwcaps_sku caps_sku;
+ u8 reserved[3];
+} __attribute__ ((packed));
+
+#endif /* _INTEL_ME_H */
diff --git a/src/southbridge/intel/lynxpoint/me_9.x.c b/src/southbridge/intel/lynxpoint/me_9.x.c
new file mode 100644
index 0000000..e691cf3
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/me_9.x.c
@@ -0,0 +1,936 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2011 The Chromium OS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/*
+ * This is a ramstage driver for the Intel Management Engine found in the
+ * 6-series chipset. It handles the required boot-time messages over the
+ * MMIO-based Management Engine Interface to tell the ME that the BIOS is
+ * finished with POST. Additional messages are defined for debug but are
+ * not used unless the console loglevel is high enough.
+ */
+
+#include <arch/acpi.h>
+#include <arch/hlt.h>
+#include <arch/io.h>
+#include <console/console.h>
+#include <device/pci_ids.h>
+#include <device/pci_def.h>
+#include <string.h>
+#include <delay.h>
+#include <elog.h>
+
+#ifdef __SMM__
+# include <arch/romcc_io.h>
+# include <northbridge/intel/haswell/pcie_config.c>
+#else
+# include <device/device.h>
+# include <device/pci.h>
+#endif
+
+#include "me.h"
+#include "pch.h"
+
+#if CONFIG_CHROMEOS
+#include <vendorcode/google/chromeos/chromeos.h>
+#include <vendorcode/google/chromeos/gnvs.h>
+#endif
+
+#ifndef __SMM__
+/* Path that the BIOS should take based on ME state */
+static const char *me_bios_path_values[] = {
+ [ME_NORMAL_BIOS_PATH] = "Normal",
+ [ME_S3WAKE_BIOS_PATH] = "S3 Wake",
+ [ME_ERROR_BIOS_PATH] = "Error",
+ [ME_RECOVERY_BIOS_PATH] = "Recovery",
+ [ME_DISABLE_BIOS_PATH] = "Disable",
+ [ME_FIRMWARE_UPDATE_BIOS_PATH] = "Firmware Update",
+};
+static int intel_me_read_mbp(me_bios_payload *mbp_data);
+#endif
+
+/* MMIO base address for MEI interface */
+static u32 mei_base_address;
+
+#if CONFIG_DEBUG_INTEL_ME
+static void mei_dump(void *ptr, int dword, int offset, const char *type)
+{
+ struct mei_csr *csr;
+
+ printk(BIOS_SPEW, "%-9s[%02x] : ", type, offset);
+
+ switch (offset) {
+ case MEI_H_CSR:
+ case MEI_ME_CSR_HA:
+ csr = ptr;
+ if (!csr) {
+ printk(BIOS_SPEW, "ERROR: 0x%08x\n", dword);
+ break;
+ }
+ printk(BIOS_SPEW, "cbd=%u cbrp=%02u cbwp=%02u ready=%u "
+ "reset=%u ig=%u is=%u ie=%u\n", csr->buffer_depth,
+ csr->buffer_read_ptr, csr->buffer_write_ptr,
+ csr->ready, csr->reset, csr->interrupt_generate,
+ csr->interrupt_status, csr->interrupt_enable);
+ break;
+ case MEI_ME_CB_RW:
+ case MEI_H_CB_WW:
+ printk(BIOS_SPEW, "CB: 0x%08x\n", dword);
+ break;
+ default:
+ printk(BIOS_SPEW, "0x%08x\n", offset);
+ break;
+ }
+}
+#else
+# define mei_dump(ptr,dword,offset,type) do {} while (0)
+#endif
+
+/*
+ * ME/MEI access helpers using memcpy to avoid aliasing.
+ */
+
+static inline void mei_read_dword_ptr(void *ptr, int offset)
+{
+ u32 dword = read32(mei_base_address + offset);
+ memcpy(ptr, &dword, sizeof(dword));
+ mei_dump(ptr, dword, offset, "READ");
+}
+
+static inline void mei_write_dword_ptr(void *ptr, int offset)
+{
+ u32 dword = 0;
+ memcpy(&dword, ptr, sizeof(dword));
+ write32(mei_base_address + offset, dword);
+ mei_dump(ptr, dword, offset, "WRITE");
+}
+
+#ifndef __SMM__
+static inline void pci_read_dword_ptr(device_t dev, void *ptr, int offset)
+{
+ u32 dword = pci_read_config32(dev, offset);
+ memcpy(ptr, &dword, sizeof(dword));
+ mei_dump(ptr, dword, offset, "PCI READ");
+}
+#endif
+
+static inline void read_host_csr(struct mei_csr *csr)
+{
+ mei_read_dword_ptr(csr, MEI_H_CSR);
+}
+
+static inline void write_host_csr(struct mei_csr *csr)
+{
+ mei_write_dword_ptr(csr, MEI_H_CSR);
+}
+
+static inline void read_me_csr(struct mei_csr *csr)
+{
+ mei_read_dword_ptr(csr, MEI_ME_CSR_HA);
+}
+
+static inline void write_cb(u32 dword)
+{
+ write32(mei_base_address + MEI_H_CB_WW, dword);
+ mei_dump(NULL, dword, MEI_H_CB_WW, "WRITE");
+}
+
+static inline u32 read_cb(void)
+{
+ u32 dword = read32(mei_base_address + MEI_ME_CB_RW);
+ mei_dump(NULL, dword, MEI_ME_CB_RW, "READ");
+ return dword;
+}
+
+/* Wait for ME ready bit to be asserted */
+static int mei_wait_for_me_ready(void)
+{
+ struct mei_csr me;
+ unsigned try = ME_RETRY;
+
+ while (try--) {
+ read_me_csr(&me);
+ if (me.ready)
+ return 0;
+ udelay(ME_DELAY);
+ }
+
+ printk(BIOS_ERR, "ME: failed to become ready\n");
+ return -1;
+}
+
+static void mei_reset(void)
+{
+ struct mei_csr host;
+
+ if (mei_wait_for_me_ready() < 0)
+ return;
+
+ /* Reset host and ME circular buffers for next message */
+ read_host_csr(&host);
+ host.reset = 1;
+ host.interrupt_generate = 1;
+ write_host_csr(&host);
+
+ if (mei_wait_for_me_ready() < 0)
+ return;
+
+ /* Re-init and indicate host is ready */
+ read_host_csr(&host);
+ host.interrupt_generate = 1;
+ host.ready = 1;
+ host.reset = 0;
+ write_host_csr(&host);
+}
+
+static int mei_send_msg(struct mei_header *mei, struct mkhi_header *mkhi,
+ void *req_data)
+{
+ struct mei_csr host;
+ unsigned ndata, n;
+ u32 *data;
+
+ /* Number of dwords to write, ignoring MKHI */
+ ndata = mei->length >> 2;
+
+ /* Pad non-dword aligned request message length */
+ if (mei->length & 3)
+ ndata++;
+ if (!ndata) {
+ printk(BIOS_DEBUG, "ME: request does not include MKHI\n");
+ return -1;
+ }
+ ndata++; /* Add MEI header */
+
+ /*
+ * Make sure there is still room left in the circular buffer.
+ * Reset the buffer pointers if the requested message will not fit.
+ */
+ read_host_csr(&host);
+ if ((host.buffer_depth - host.buffer_write_ptr) < ndata) {
+ printk(BIOS_ERR, "ME: circular buffer full, resetting...\n");
+ mei_reset();
+ read_host_csr(&host);
+ }
+
+ /*
+ * This implementation does not handle splitting large messages
+ * across multiple transactions. Ensure the requested length
+ * will fit in the available circular buffer depth.
+ */
+ if ((host.buffer_depth - host.buffer_write_ptr) < ndata) {
+ printk(BIOS_ERR, "ME: message (%u) too large for buffer (%u)\n",
+ ndata + 2, host.buffer_depth);
+ return -1;
+ }
+
+ /* Write MEI header */
+ mei_write_dword_ptr(mei, MEI_H_CB_WW);
+ ndata--;
+
+ /* Write MKHI header */
+ mei_write_dword_ptr(mkhi, MEI_H_CB_WW);
+ ndata--;
+
+ /* Write message data */
+ data = req_data;
+ for (n = 0; n < ndata; ++n)
+ write_cb(*data++);
+
+ /* Generate interrupt to the ME */
+ read_host_csr(&host);
+ host.interrupt_generate = 1;
+ write_host_csr(&host);
+
+ /* Make sure ME is ready after sending request data */
+ return mei_wait_for_me_ready();
+}
+
+static int mei_recv_msg(struct mkhi_header *mkhi,
+ void *rsp_data, int rsp_bytes)
+{
+ struct mei_header mei_rsp;
+ struct mkhi_header mkhi_rsp;
+ struct mei_csr me, host;
+ unsigned ndata, n/*, me_data_len*/;
+ unsigned expected;
+ u32 *data;
+
+ /* Total number of dwords to read from circular buffer */
+ expected = (rsp_bytes + sizeof(mei_rsp) + sizeof(mkhi_rsp)) >> 2;
+ if (rsp_bytes & 3)
+ expected++;
+
+ /*
+ * The interrupt status bit does not appear to indicate that the
+ * message has actually been received. Instead we wait until the
+ * expected number of dwords are present in the circular buffer.
+ */
+ for (n = ME_RETRY; n; --n) {
+ read_me_csr(&me);
+ if ((me.buffer_write_ptr - me.buffer_read_ptr) >= expected)
+ break;
+ udelay(ME_DELAY);
+ }
+ if (!n) {
+ printk(BIOS_ERR, "ME: timeout waiting for data: expected "
+ "%u, available %u\n", expected,
+ me.buffer_write_ptr - me.buffer_read_ptr);
+ return -1;
+ }
+
+ /* Read and verify MEI response header from the ME */
+ mei_read_dword_ptr(&mei_rsp, MEI_ME_CB_RW);
+ if (!mei_rsp.is_complete) {
+ printk(BIOS_ERR, "ME: response is not complete\n");
+ return -1;
+ }
+
+ /* Handle non-dword responses and expect at least MKHI header */
+ ndata = mei_rsp.length >> 2;
+ if (mei_rsp.length & 3)
+ ndata++;
+ if (ndata != (expected - 1)) {
+ printk(BIOS_ERR, "ME: response is missing data %d != %d\n",
+ ndata, (expected - 1));
+ return -1;
+ }
+
+ /* Read and verify MKHI response header from the ME */
+ mei_read_dword_ptr(&mkhi_rsp, MEI_ME_CB_RW);
+ if (!mkhi_rsp.is_response ||
+ mkhi->group_id != mkhi_rsp.group_id ||
+ mkhi->command != mkhi_rsp.command) {
+ printk(BIOS_ERR, "ME: invalid response, group %u ?= %u,"
+ "command %u ?= %u, is_response %u\n", mkhi->group_id,
+ mkhi_rsp.group_id, mkhi->command, mkhi_rsp.command,
+ mkhi_rsp.is_response);
+ return -1;
+ }
+ ndata--; /* MKHI header has been read */
+
+ /* Make sure caller passed a buffer with enough space */
+ if (ndata != (rsp_bytes >> 2)) {
+ printk(BIOS_ERR, "ME: not enough room in response buffer: "
+ "%u != %u\n", ndata, rsp_bytes >> 2);
+ return -1;
+ }
+
+ /* Read response data from the circular buffer */
+ data = rsp_data;
+ for (n = 0; n < ndata; ++n)
+ *data++ = read_cb();
+
+ /* Tell the ME that we have consumed the response */
+ read_host_csr(&host);
+ host.interrupt_status = 1;
+ host.interrupt_generate = 1;
+ write_host_csr(&host);
+
+ return mei_wait_for_me_ready();
+}
+
+static inline int mei_sendrecv(struct mei_header *mei, struct mkhi_header *mkhi,
+ void *req_data, void *rsp_data, int rsp_bytes)
+{
+ if (mei_send_msg(mei, mkhi, req_data) < 0)
+ return -1;
+ if (mei_recv_msg(mkhi, rsp_data, rsp_bytes) < 0)
+ return -1;
+ return 0;
+}
+
+#if (CONFIG_DEFAULT_CONSOLE_LOGLEVEL >= BIOS_DEBUG) && !defined(__SMM__)
+static inline void print_cap(const char *name, int state)
+{
+ printk(BIOS_DEBUG, "ME Capability: %-41s : %sabled\n",
+ name, state ? " en" : "dis");
+}
+
+static void me_print_fw_version(mbp_fw_version_name *vers_name)
+{
+ if (!vers_name->major_version) {
+ printk(BIOS_ERR, "ME: mbp missing version report\n");
+ return;
+ }
+
+ printk(BIOS_DEBUG, "ME: found version %d.%d.%d.%d\n",
+ vers_name->major_version, vers_name->minor_version,
+ vers_name->hotfix_version, vers_name->build_version);
+}
+
+/* Get ME Firmware Capabilities */
+static int mkhi_get_fwcaps(mefwcaps_sku *cap)
+{
+ u32 rule_id = 0;
+ struct me_fwcaps cap_msg;
+ struct mkhi_header mkhi = {
+ .group_id = MKHI_GROUP_ID_FWCAPS,
+ .command = MKHI_FWCAPS_GET_RULE,
+ };
+ struct mei_header mei = {
+ .is_complete = 1,
+ .host_address = MEI_HOST_ADDRESS,
+ .client_address = MEI_ADDRESS_MKHI,
+ .length = sizeof(mkhi) + sizeof(rule_id),
+ };
+
+ /* Send request and wait for response */
+ if (mei_sendrecv(&mei, &mkhi, &rule_id, &cap_msg, sizeof(cap_msg))
+ < 0) {
+ printk(BIOS_ERR, "ME: GET FWCAPS message failed\n");
+ return -1;
+ }
+ *cap = cap_msg.caps_sku;
+ return 0;
+}
+
+/* Get ME Firmware Capabilities */
+static void me_print_fwcaps(mbp_fw_caps *caps_section)
+{
+ mefwcaps_sku *cap = &caps_section->fw_capabilities;
+ if (!caps_section->available) {
+ printk(BIOS_ERR, "ME: mbp missing fwcaps report\n");
+ if (mkhi_get_fwcaps(cap))
+ return;
+ }
+
+ print_cap("Full Network manageability", cap->full_net);
+ print_cap("Regular Network manageability", cap->std_net);
+ print_cap("Manageability", cap->manageability);
+ print_cap("Small business technology", cap->small_business);
+ print_cap("Level III manageability", cap->l3manageability);
+ print_cap("IntelR Anti-Theft (AT)", cap->intel_at);
+ print_cap("IntelR Capability Licensing Service (CLS)", cap->intel_cls);
+ print_cap("IntelR Power Sharing Technology (MPC)", cap->intel_mpc);
+ print_cap("ICC Over Clocking", cap->icc_over_clocking);
+ print_cap("Protected Audio Video Path (PAVP)", cap->pavp);
+ print_cap("IPV6", cap->ipv6);
+ print_cap("KVM Remote Control (KVM)", cap->kvm);
+ print_cap("Outbreak Containment Heuristic (OCH)", cap->och);
+ print_cap("Virtual LAN (VLAN)", cap->vlan);
+ print_cap("TLS", cap->tls);
+ print_cap("Wireless LAN (WLAN)", cap->wlan);
+}
+#endif
+
+#if CONFIG_CHROMEOS && 0 /* DISABLED */
+/* Tell ME to issue a global reset */
+static int mkhi_global_reset(void)
+{
+ struct me_global_reset reset = {
+ .request_origin = GLOBAL_RESET_BIOS_POST,
+ .reset_type = CBM_RR_GLOBAL_RESET,
+ };
+ struct mkhi_header mkhi = {
+ .group_id = MKHI_GROUP_ID_CBM,
+ .command = MKHI_GLOBAL_RESET,
+ };
+ struct mei_header mei = {
+ .is_complete = 1,
+ .length = sizeof(mkhi) + sizeof(reset),
+ .host_address = MEI_HOST_ADDRESS,
+ .client_address = MEI_ADDRESS_MKHI,
+ };
+
+ /* Send request and wait for response */
+ printk(BIOS_NOTICE, "ME: %s\n", __FUNCTION__);
+ if (mei_sendrecv(&mei, &mkhi, &reset, NULL, 0) < 0) {
+ /* No response means reset will happen shortly... */
+ hlt();
+ }
+
+ /* If the ME responded it rejected the reset request */
+ printk(BIOS_ERR, "ME: Global Reset failed\n");
+ return -1;
+}
+#endif
+
+#ifdef __SMM__
+
+/* Send END OF POST message to the ME */
+static int mkhi_end_of_post(void)
+{
+ struct mkhi_header mkhi = {
+ .group_id = MKHI_GROUP_ID_GEN,
+ .command = MKHI_END_OF_POST,
+ };
+ struct mei_header mei = {
+ .is_complete = 1,
+ .host_address = MEI_HOST_ADDRESS,
+ .client_address = MEI_ADDRESS_MKHI,
+ .length = sizeof(mkhi),
+ };
+
+ u32 eop_ack;
+
+ /* Send request and wait for response */
+ printk(BIOS_NOTICE, "ME: %s\n", __FUNCTION__);
+ if (mei_sendrecv(&mei, &mkhi, NULL, &eop_ack, sizeof(eop_ack)) < 0) {
+ printk(BIOS_ERR, "ME: END OF POST message failed\n");
+ return -1;
+ }
+
+ printk(BIOS_INFO, "ME: END OF POST message successful (%d)\n", eop_ack);
+ return 0;
+}
+
+void intel_me_finalize_smm(void)
+{
+ struct me_hfs hfs;
+ u32 reg32;
+
+ mei_base_address =
+ pcie_read_config32(PCH_ME_DEV, PCI_BASE_ADDRESS_0) & ~0xf;
+
+ /* S3 path will have hidden this device already */
+ if (!mei_base_address || mei_base_address == 0xfffffff0)
+ return;
+
+ /* Make sure ME is in a mode that expects EOP */
+ reg32 = pcie_read_config32(PCH_ME_DEV, PCI_ME_HFS);
+ memcpy(&hfs, ®32, sizeof(u32));
+
+ /* Abort and leave device alone if not normal mode */
+ if (hfs.fpt_bad ||
+ hfs.working_state != ME_HFS_CWS_NORMAL ||
+ hfs.operation_mode != ME_HFS_MODE_NORMAL)
+ return;
+
+ /* Try to send EOP command so ME stops accepting other commands */
+ mkhi_end_of_post();
+
+ /* Make sure IO is disabled */
+ reg32 = pcie_read_config32(PCH_ME_DEV, PCI_COMMAND);
+ reg32 &= ~(PCI_COMMAND_MASTER |
+ PCI_COMMAND_MEMORY | PCI_COMMAND_IO);
+ pcie_write_config32(PCH_ME_DEV, PCI_COMMAND, reg32);
+
+ /* Hide the PCI device */
+ RCBA32_OR(FD2, PCH_DISABLE_MEI1);
+}
+
+#else /* !__SMM__ */
+
+/* Determine the path that we should take based on ME status */
+static me_bios_path intel_me_path(device_t dev)
+{
+ me_bios_path path = ME_DISABLE_BIOS_PATH;
+ struct me_hfs hfs;
+ struct me_gmes gmes;
+
+#if CONFIG_HAVE_ACPI_RESUME
+ /* S3 wake skips all MKHI messages */
+ if (acpi_slp_type == 3) {
+ return ME_S3WAKE_BIOS_PATH;
+ }
+#endif
+
+ pci_read_dword_ptr(dev, &hfs, PCI_ME_HFS);
+ pci_read_dword_ptr(dev, &gmes, PCI_ME_GMES);
+
+ /* Check and dump status */
+ intel_me_status(&hfs, &gmes);
+
+ /* Check Current Working State */
+ switch (hfs.working_state) {
+ case ME_HFS_CWS_NORMAL:
+ path = ME_NORMAL_BIOS_PATH;
+ break;
+ case ME_HFS_CWS_REC:
+ path = ME_RECOVERY_BIOS_PATH;
+ break;
+ default:
+ path = ME_DISABLE_BIOS_PATH;
+ break;
+ }
+
+ /* Check Current Operation Mode */
+ switch (hfs.operation_mode) {
+ case ME_HFS_MODE_NORMAL:
+ break;
+ case ME_HFS_MODE_DEBUG:
+ case ME_HFS_MODE_DIS:
+ case ME_HFS_MODE_OVER_JMPR:
+ case ME_HFS_MODE_OVER_MEI:
+ default:
+ path = ME_DISABLE_BIOS_PATH;
+ break;
+ }
+
+ /* Check for any error code and valid firmware and MBP */
+ if (hfs.error_code || hfs.fpt_bad)
+ path = ME_ERROR_BIOS_PATH;
+
+ /* Check if the MBP is ready */
+ if (!gmes.mbp_rdy) {
+ printk(BIOS_CRIT, "%s: mbp is not ready!\n",
+ __FUNCTION__);
+ path = ME_ERROR_BIOS_PATH;
+ }
+
+#if CONFIG_ELOG
+ if (path != ME_NORMAL_BIOS_PATH) {
+ struct elog_event_data_me_extended data = {
+ .current_working_state = hfs.working_state,
+ .operation_state = hfs.operation_state,
+ .operation_mode = hfs.operation_mode,
+ .error_code = hfs.error_code,
+ .progress_code = gmes.progress_code,
+ .current_pmevent = gmes.current_pmevent,
+ .current_state = gmes.current_state,
+ };
+ elog_add_event_byte(ELOG_TYPE_MANAGEMENT_ENGINE, path);
+ elog_add_event_raw(ELOG_TYPE_MANAGEMENT_ENGINE_EXT,
+ &data, sizeof(data));
+ }
+#endif
+
+ return path;
+}
+
+/* Prepare ME for MEI messages */
+static int intel_mei_setup(device_t dev)
+{
+ struct resource *res;
+ struct mei_csr host;
+ u32 reg32;
+
+ /* Find the MMIO base for the ME interface */
+ res = find_resource(dev, PCI_BASE_ADDRESS_0);
+ if (!res || res->base == 0 || res->size == 0) {
+ printk(BIOS_DEBUG, "ME: MEI resource not present!\n");
+ return -1;
+ }
+ mei_base_address = res->base;
+
+ /* Ensure Memory and Bus Master bits are set */
+ reg32 = pci_read_config32(dev, PCI_COMMAND);
+ reg32 |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY;
+ pci_write_config32(dev, PCI_COMMAND, reg32);
+
+ /* Clean up status for next message */
+ read_host_csr(&host);
+ host.interrupt_generate = 1;
+ host.ready = 1;
+ host.reset = 0;
+ write_host_csr(&host);
+
+ return 0;
+}
+
+/* Read the Extend register hash of ME firmware */
+static int intel_me_extend_valid(device_t dev)
+{
+ struct me_heres status;
+ u32 extend[8] = {0};
+ int i, count = 0;
+
+ pci_read_dword_ptr(dev, &status, PCI_ME_HERES);
+ if (!status.extend_feature_present) {
+ printk(BIOS_ERR, "ME: Extend Feature not present\n");
+ return -1;
+ }
+
+ if (!status.extend_reg_valid) {
+ printk(BIOS_ERR, "ME: Extend Register not valid\n");
+ return -1;
+ }
+
+ switch (status.extend_reg_algorithm) {
+ case PCI_ME_EXT_SHA1:
+ count = 5;
+ printk(BIOS_DEBUG, "ME: Extend SHA-1: ");
+ break;
+ case PCI_ME_EXT_SHA256:
+ count = 8;
+ printk(BIOS_DEBUG, "ME: Extend SHA-256: ");
+ break;
+ default:
+ printk(BIOS_ERR, "ME: Extend Algorithm %d unknown\n",
+ status.extend_reg_algorithm);
+ return -1;
+ }
+
+ for (i = 0; i < count; ++i) {
+ extend[i] = pci_read_config32(dev, PCI_ME_HER(i));
+ printk(BIOS_DEBUG, "%08x", extend[i]);
+ }
+ printk(BIOS_DEBUG, "\n");
+
+#if CONFIG_CHROMEOS
+ /* Save hash in NVS for the OS to verify */
+ chromeos_set_me_hash(extend, count);
+#endif
+
+ return 0;
+}
+
+/* Hide the ME virtual PCI devices */
+static void intel_me_hide(device_t dev)
+{
+ dev->enabled = 0;
+ pch_enable(dev);
+}
+
+/* Check whether ME is present and do basic init */
+static void intel_me_init(device_t dev)
+{
+ me_bios_path path = intel_me_path(dev);
+ me_bios_payload mbp_data;
+
+ /* Do initial setup and determine the BIOS path */
+ printk(BIOS_NOTICE, "ME: BIOS path: %s\n", me_bios_path_values[path]);
+
+ switch (path) {
+ case ME_S3WAKE_BIOS_PATH:
+ intel_me_hide(dev);
+ break;
+
+ case ME_NORMAL_BIOS_PATH:
+ /* Validate the extend register */
+ if (intel_me_extend_valid(dev) < 0)
+ break; /* TODO: force recovery mode */
+
+ /* Prepare MEI MMIO interface */
+ if (intel_mei_setup(dev) < 0)
+ break;
+
+ if(intel_me_read_mbp(&mbp_data))
+ break;
+
+#if CONFIG_CHROMEOS && 0 /* DISABLED */
+ /*
+ * Unlock ME in recovery mode.
+ */
+ if (recovery_mode_enabled()) {
+ /* Unlock ME flash region */
+ mkhi_hmrfpo_enable();
+
+ /* Issue global reset */
+ mkhi_global_reset();
+ return;
+ }
+#endif
+
+#if (CONFIG_DEFAULT_CONSOLE_LOGLEVEL >= BIOS_DEBUG)
+ me_print_fw_version(&mbp_data.fw_version_name);
+ me_print_fwcaps(&mbp_data.fw_caps_sku);
+#endif
+
+ /*
+ * Leave the ME unlocked in this path.
+ * It will be locked via SMI command later.
+ */
+ break;
+
+ case ME_ERROR_BIOS_PATH:
+ case ME_RECOVERY_BIOS_PATH:
+ case ME_DISABLE_BIOS_PATH:
+ case ME_FIRMWARE_UPDATE_BIOS_PATH:
+ break;
+ }
+}
+
+static void set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ if (!vendor || !device) {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ pci_read_config32(dev, PCI_VENDOR_ID));
+ } else {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+ }
+}
+
+static struct pci_operations pci_ops = {
+ .set_subsystem = set_subsystem,
+};
+
+static struct device_operations device_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = intel_me_init,
+ .scan_bus = scan_static_bus,
+ .ops_pci = &pci_ops,
+};
+
+static const struct pci_driver intel_me __pci_driver = {
+ .ops = &device_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = 0x1e3a,
+};
+
+/******************************************************************************
+ * */
+static u32 me_to_host_words_pending(void)
+{
+ struct mei_csr me;
+ read_me_csr(&me);
+ if (!me.ready)
+ return 0;
+ return (me.buffer_write_ptr - me.buffer_read_ptr) &
+ (me.buffer_depth - 1);
+}
+
+#if 0
+/* This function is not yet being used, keep it in for the future. */
+static u32 host_to_me_words_room(void)
+{
+ struct mei_csr csr;
+
+ read_me_csr(&csr);
+ if (!csr.ready)
+ return 0;
+
+ read_host_csr(&csr);
+ return (csr.buffer_read_ptr - csr.buffer_write_ptr - 1) &
+ (csr.buffer_depth - 1);
+}
+#endif
+/*
+ * mbp seems to be following its own flow, let's retrieve it in a dedicated
+ * function.
+ */
+static int intel_me_read_mbp(me_bios_payload *mbp_data)
+{
+ mbp_header mbp_hdr;
+ mbp_item_header mbp_item_hdr;
+ u32 me2host_pending;
+ u32 mbp_item_id;
+ struct mei_csr host;
+
+ me2host_pending = me_to_host_words_pending();
+ if (!me2host_pending) {
+ printk(BIOS_ERR, "ME: no mbp data!\n");
+ return -1;
+ }
+
+ /* we know for sure that at least the header is there */
+ mei_read_dword_ptr(&mbp_hdr, MEI_ME_CB_RW);
+
+ if ((mbp_hdr.num_entries > (mbp_hdr.mbp_size / 2)) ||
+ (me2host_pending < mbp_hdr.mbp_size)) {
+ printk(BIOS_ERR, "ME: mbp of %d entries, total size %d words"
+ " buffer contains %d words\n",
+ mbp_hdr.num_entries, mbp_hdr.mbp_size,
+ me2host_pending);
+ return -1;
+ }
+
+ me2host_pending--;
+ memset(mbp_data, 0, sizeof(*mbp_data));
+
+ while (mbp_hdr.num_entries--) {
+ u32* copy_addr;
+ u32 copy_size, buffer_room;
+ void *p;
+
+ if (!me2host_pending) {
+ printk(BIOS_ERR, "ME: no mbp data %d entries to go!\n",
+ mbp_hdr.num_entries + 1);
+ return -1;
+ }
+
+ mei_read_dword_ptr(&mbp_item_hdr, MEI_ME_CB_RW);
+
+ if (mbp_item_hdr.length > me2host_pending) {
+ printk(BIOS_ERR, "ME: insufficient mbp data %d "
+ "entries to go!\n",
+ mbp_hdr.num_entries + 1);
+ return -1;
+ }
+
+ me2host_pending -= mbp_item_hdr.length;
+
+ mbp_item_id = (((u32)mbp_item_hdr.item_id) << 8) +
+ mbp_item_hdr.app_id;
+
+ copy_size = mbp_item_hdr.length - 1;
+
+#define SET_UP_COPY(field) { copy_addr = (u32 *)&mbp_data->field; \
+ buffer_room = sizeof(mbp_data->field) / sizeof(u32); \
+ break; \
+ }
+
+ p = &mbp_item_hdr;
+ printk(BIOS_INFO, "ME: MBP item header %8.8x\n", *((u32*)p));
+
+ switch(mbp_item_id) {
+ case 0x101:
+ SET_UP_COPY(fw_version_name);
+
+ case 0x102:
+ SET_UP_COPY(icc_profile);
+
+ case 0x103:
+ SET_UP_COPY(at_state);
+
+ case 0x201:
+ mbp_data->fw_caps_sku.available = 1;
+ SET_UP_COPY(fw_caps_sku.fw_capabilities);
+
+ case 0x301:
+ SET_UP_COPY(rom_bist_data);
+
+ case 0x401:
+ SET_UP_COPY(platform_key);
+
+ case 0x501:
+ mbp_data->fw_plat_type.available = 1;
+ SET_UP_COPY(fw_plat_type.rule_data);
+
+ case 0x601:
+ SET_UP_COPY(mfsintegrity);
+
+ default:
+ printk(BIOS_ERR, "ME: unknown mbp item id 0x%x!!!\n",
+ mbp_item_id);
+ return -1;
+ }
+
+ if (buffer_room != copy_size) {
+ printk(BIOS_ERR, "ME: buffer room %d != %d copy size"
+ " for item 0x%x!!!\n",
+ buffer_room, copy_size, mbp_item_id);
+ return -1;
+ }
+ while(copy_size--)
+ *copy_addr++ = read_cb();
+ }
+
+ read_host_csr(&host);
+ host.interrupt_generate = 1;
+ write_host_csr(&host);
+
+ {
+ int cntr = 0;
+ while(host.interrupt_generate) {
+ read_host_csr(&host);
+ cntr++;
+ }
+ printk(BIOS_SPEW, "ME: mbp read OK after %d cycles\n", cntr);
+ }
+
+ return 0;
+}
+
+#endif /* !__SMM__ */
diff --git a/src/southbridge/intel/lynxpoint/me_status.c b/src/southbridge/intel/lynxpoint/me_status.c
new file mode 100644
index 0000000..b2f38d6
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/me_status.c
@@ -0,0 +1,213 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2011 The Chromium OS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <stdlib.h>
+#include <console/console.h>
+#include "me.h"
+
+#if (CONFIG_DEFAULT_CONSOLE_LOGLEVEL >= BIOS_DEBUG)
+/* HFS1[3:0] Current Working State Values */
+static const char *me_cws_values[] = {
+ [ME_HFS_CWS_RESET] = "Reset",
+ [ME_HFS_CWS_INIT] = "Initializing",
+ [ME_HFS_CWS_REC] = "Recovery",
+ [ME_HFS_CWS_NORMAL] = "Normal",
+ [ME_HFS_CWS_WAIT] = "Platform Disable Wait",
+ [ME_HFS_CWS_TRANS] = "OP State Transition",
+ [ME_HFS_CWS_INVALID] = "Invalid CPU Plugged In"
+};
+
+/* HFS1[8:6] Current Operation State Values */
+static const char *me_opstate_values[] = {
+ [ME_HFS_STATE_PREBOOT] = "Preboot",
+ [ME_HFS_STATE_M0_UMA] = "M0 with UMA",
+ [ME_HFS_STATE_M3] = "M3 without UMA",
+ [ME_HFS_STATE_M0] = "M0 without UMA",
+ [ME_HFS_STATE_BRINGUP] = "Bring up",
+ [ME_HFS_STATE_ERROR] = "M0 without UMA but with error"
+};
+
+/* HFS[19:16] Current Operation Mode Values */
+static const char *me_opmode_values[] = {
+ [ME_HFS_MODE_NORMAL] = "Normal",
+ [ME_HFS_MODE_DEBUG] = "Debug",
+ [ME_HFS_MODE_DIS] = "Soft Temporary Disable",
+ [ME_HFS_MODE_OVER_JMPR] = "Security Override via Jumper",
+ [ME_HFS_MODE_OVER_MEI] = "Security Override via MEI Message"
+};
+
+/* HFS[15:12] Error Code Values */
+static const char *me_error_values[] = {
+ [ME_HFS_ERROR_NONE] = "No Error",
+ [ME_HFS_ERROR_UNCAT] = "Uncategorized Failure",
+ [ME_HFS_ERROR_IMAGE] = "Image Failure",
+ [ME_HFS_ERROR_DEBUG] = "Debug Failure"
+};
+
+/* GMES[31:28] ME Progress Code */
+static const char *me_progress_values[] = {
+ [ME_GMES_PHASE_ROM] = "ROM Phase",
+ [ME_GMES_PHASE_BUP] = "BUP Phase",
+ [ME_GMES_PHASE_UKERNEL] = "uKernel Phase",
+ [ME_GMES_PHASE_POLICY] = "Policy Module",
+ [ME_GMES_PHASE_MODULE] = "Module Loading",
+ [ME_GMES_PHASE_UNKNOWN] = "Unknown",
+ [ME_GMES_PHASE_HOST] = "Host Communication"
+};
+
+/* GMES[27:24] Power Management Event */
+static const char *me_pmevent_values[] = {
+ [0x00] = "Clean Moff->Mx wake",
+ [0x01] = "Moff->Mx wake after an error",
+ [0x02] = "Clean global reset",
+ [0x03] = "Global reset after an error",
+ [0x04] = "Clean Intel ME reset",
+ [0x05] = "Intel ME reset due to exception",
+ [0x06] = "Pseudo-global reset",
+ [0x07] = "S0/M0->Sx/M3",
+ [0x08] = "Sx/M3->S0/M0",
+ [0x09] = "Non-power cycle reset",
+ [0x0a] = "Power cycle reset through M3",
+ [0x0b] = "Power cycle reset through Moff",
+ [0x0c] = "Sx/Mx->Sx/Moff"
+};
+
+/* Progress Code 0 states */
+static const char *me_progress_rom_values[] = {
+ [0x00] = "BEGIN",
+ [0x06] = "DISABLE"
+};
+
+/* Progress Code 1 states */
+static const char *me_progress_bup_values[] = {
+ [0x00] = "Initialization starts",
+ [0x01] = "Disable the host wake event",
+ [0x04] = "Flow determination start process",
+ [0x08] = "Error reading/matching the VSCC table in the descriptor",
+ [0x0a] = "Check to see if straps say ME DISABLED",
+ [0x0b] = "Timeout waiting for PWROK",
+ [0x0d] = "Possibly handle BUP manufacturing override strap",
+ [0x11] = "Bringup in M3",
+ [0x12] = "Bringup in M0",
+ [0x13] = "Flow detection error",
+ [0x15] = "M3 clock switching error",
+ [0x18] = "M3 kernel load",
+ [0x1c] = "T34 missing - cannot program ICC",
+ [0x1f] = "Waiting for DID BIOS message",
+ [0x20] = "Waiting for DID BIOS message failure",
+ [0x21] = "DID reported an error",
+ [0x22] = "Enabling UMA",
+ [0x23] = "Enabling UMA error",
+ [0x24] = "Sending DID Ack to BIOS",
+ [0x25] = "Sending DID Ack to BIOS error",
+ [0x26] = "Switching clocks in M0",
+ [0x27] = "Switching clocks in M0 error",
+ [0x28] = "ME in temp disable",
+ [0x32] = "M0 kernel load",
+};
+
+/* Progress Code 3 states */
+static const char *me_progress_policy_values[] = {
+ [0x00] = "Entery into Policy Module",
+ [0x03] = "Received S3 entry",
+ [0x04] = "Received S4 entry",
+ [0x05] = "Received S5 entry",
+ [0x06] = "Received UPD entry",
+ [0x07] = "Received PCR entry",
+ [0x08] = "Received NPCR entry",
+ [0x09] = "Received host wake",
+ [0x0a] = "Received AC<>DC switch",
+ [0x0b] = "Received DRAM Init Done",
+ [0x0c] = "VSCC Data not found for flash device",
+ [0x0d] = "VSCC Table is not valid",
+ [0x0e] = "Flash Partition Boundary is outside address space",
+ [0x0f] = "ME cannot access the chipset descriptor region",
+ [0x10] = "Required VSCC values for flash parts do not match",
+};
+#endif
+
+void intel_me_status(struct me_hfs *hfs, struct me_gmes *gmes)
+{
+#if (CONFIG_DEFAULT_CONSOLE_LOGLEVEL >= BIOS_DEBUG)
+ /* Check Current States */
+ printk(BIOS_DEBUG, "ME: FW Partition Table : %s\n",
+ hfs->fpt_bad ? "BAD" : "OK");
+ printk(BIOS_DEBUG, "ME: Bringup Loader Failure : %s\n",
+ hfs->ft_bup_ld_flr ? "YES" : "NO");
+ printk(BIOS_DEBUG, "ME: Firmware Init Complete : %s\n",
+ hfs->fw_init_complete ? "YES" : "NO");
+ printk(BIOS_DEBUG, "ME: Manufacturing Mode : %s\n",
+ hfs->mfg_mode ? "YES" : "NO");
+ printk(BIOS_DEBUG, "ME: Boot Options Present : %s\n",
+ hfs->boot_options_present ? "YES" : "NO");
+ printk(BIOS_DEBUG, "ME: Update In Progress : %s\n",
+ hfs->update_in_progress ? "YES" : "NO");
+ printk(BIOS_DEBUG, "ME: Current Working State : %s\n",
+ me_cws_values[hfs->working_state]);
+ printk(BIOS_DEBUG, "ME: Current Operation State : %s\n",
+ me_opstate_values[hfs->operation_state]);
+ printk(BIOS_DEBUG, "ME: Current Operation Mode : %s\n",
+ me_opmode_values[hfs->operation_mode]);
+ printk(BIOS_DEBUG, "ME: Error Code : %s\n",
+ me_error_values[hfs->error_code]);
+ printk(BIOS_DEBUG, "ME: Progress Phase : %s\n",
+ me_progress_values[gmes->progress_code]);
+ printk(BIOS_DEBUG, "ME: Power Management Event : %s\n",
+ me_pmevent_values[gmes->current_pmevent]);
+
+ printk(BIOS_DEBUG, "ME: Progress Phase State : ");
+ switch (gmes->progress_code) {
+ case ME_GMES_PHASE_ROM: /* ROM Phase */
+ printk(BIOS_DEBUG, "%s",
+ me_progress_rom_values[gmes->current_state]);
+ break;
+
+ case ME_GMES_PHASE_BUP: /* Bringup Phase */
+ if (gmes->current_state < ARRAY_SIZE(me_progress_bup_values)
+ && me_progress_bup_values[gmes->current_state])
+ printk(BIOS_DEBUG, "%s",
+ me_progress_bup_values[gmes->current_state]);
+ else
+ printk(BIOS_DEBUG, "0x%02x", gmes->current_state);
+ break;
+
+ case ME_GMES_PHASE_POLICY: /* Policy Module Phase */
+ if (gmes->current_state < ARRAY_SIZE(me_progress_policy_values)
+ && me_progress_policy_values[gmes->current_state])
+ printk(BIOS_DEBUG, "%s",
+ me_progress_policy_values[gmes->current_state]);
+ else
+ printk(BIOS_DEBUG, "0x%02x", gmes->current_state);
+ break;
+
+ case ME_GMES_PHASE_HOST: /* Host Communication Phase */
+ if (!gmes->current_state)
+ printk(BIOS_DEBUG, "Host communication established");
+ else
+ printk(BIOS_DEBUG, "0x%02x", gmes->current_state);
+ break;
+
+ default:
+ printk(BIOS_DEBUG, "Unknown 0x%02x", gmes->current_state);
+ }
+ printk(BIOS_DEBUG, "\n");
+#endif
+}
diff --git a/src/southbridge/intel/lynxpoint/nvs.h b/src/southbridge/intel/lynxpoint/nvs.h
new file mode 100644
index 0000000..b8506d4
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/nvs.h
@@ -0,0 +1,158 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ * Copyright (C) 2011 Google Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include "vendorcode/google/chromeos/gnvs.h"
+typedef struct {
+ /* Miscellaneous */
+ u16 osys; /* 0x00 - Operating System */
+ u8 smif; /* 0x02 - SMI function call ("TRAP") */
+ u8 prm0; /* 0x03 - SMI function call parameter */
+ u8 prm1; /* 0x04 - SMI function call parameter */
+ u8 scif; /* 0x05 - SCI function call (via _L00) */
+ u8 prm2; /* 0x06 - SCI function call parameter */
+ u8 prm3; /* 0x07 - SCI function call parameter */
+ u8 lckf; /* 0x08 - Global Lock function for EC */
+ u8 prm4; /* 0x09 - Lock function parameter */
+ u8 prm5; /* 0x0a - Lock function parameter */
+ u32 p80d; /* 0x0b - Debug port (IO 0x80) value */
+ u8 lids; /* 0x0f - LID state (open = 1) */
+ u8 pwrs; /* 0x10 - Power state (AC = 1) */
+ /* Thermal policy */
+ u8 tlvl; /* 0x11 - Throttle Level Limit */
+ u8 flvl; /* 0x12 - Current FAN Level */
+ u8 tcrt; /* 0x13 - Critical Threshold */
+ u8 tpsv; /* 0x14 - Passive Threshold */
+ u8 tmax; /* 0x15 - CPU Tj_max */
+ u8 f0of; /* 0x16 - FAN 0 OFF Threshold */
+ u8 f0on; /* 0x17 - FAN 0 ON Threshold */
+ u8 f0pw; /* 0x18 - FAN 0 PWM value */
+ u8 f1of; /* 0x19 - FAN 1 OFF Threshold */
+ u8 f1on; /* 0x1a - FAN 1 ON Threshold */
+ u8 f1pw; /* 0x1b - FAN 1 PWM value */
+ u8 f2of; /* 0x1c - FAN 2 OFF Threshold */
+ u8 f2on; /* 0x1d - FAN 2 ON Threshold */
+ u8 f2pw; /* 0x1e - FAN 2 PWM value */
+ u8 f3of; /* 0x1f - FAN 3 OFF Threshold */
+ u8 f3on; /* 0x20 - FAN 3 ON Threshold */
+ u8 f3pw; /* 0x21 - FAN 3 PWM value */
+ u8 f4of; /* 0x22 - FAN 4 OFF Threshold */
+ u8 f4on; /* 0x23 - FAN 4 ON Threshold */
+ u8 f4pw; /* 0x24 - FAN 4 PWM value */
+ u8 tmps; /* 0x25 - Temperature Sensor ID */
+ u8 rsvd3[2];
+ /* Processor Identification */
+ u8 apic; /* 0x28 - APIC enabled */
+ u8 mpen; /* 0x29 - MP capable/enabled */
+ u8 pcp0; /* 0x2a - PDC CPU/CORE 0 */
+ u8 pcp1; /* 0x2b - PDC CPU/CORE 1 */
+ u8 ppcm; /* 0x2c - Max. PPC state */
+ u8 pcnt; /* 0x2d - Processor Count */
+ u8 rsvd4[4];
+ /* Super I/O & CMOS config */
+ u8 natp; /* 0x32 - SIO type */
+ u8 s5u0; /* 0x33 - Enable USB0 in S5 */
+ u8 s5u1; /* 0x34 - Enable USB1 in S5 */
+ u8 s3u0; /* 0x35 - Enable USB0 in S3 */
+ u8 s3u1; /* 0x36 - Enable USB1 in S3 */
+ u8 s33g; /* 0x37 - Enable S3 in 3G */
+ u32 cmem; /* 0x38 - CBMEM TOC */
+ /* Integrated Graphics Device */
+ u8 igds; /* 0x3c - IGD state */
+ u8 tlst; /* 0x3d - Display Toggle List Pointer */
+ u8 cadl; /* 0x3e - currently attached devices */
+ u8 padl; /* 0x3f - previously attached devices */
+ u16 cste; /* 0x40 - current display state */
+ u16 nste; /* 0x42 - next display state */
+ u16 sste; /* 0x44 - set display state */
+ u8 ndid; /* 0x46 - number of device ids */
+ u32 did[5]; /* 0x47 - 5b device id 1..5 */
+ u8 rsvd5[0x9];
+ /* Backlight Control */
+ u8 blcs; /* 0x64 - Backlight Control possible */
+ u8 brtl;
+ u8 odds;
+ u8 rsvd6[0x7];
+ /* Ambient Light Sensors*/
+ u8 alse; /* 0x6e - ALS enable */
+ u8 alaf;
+ u8 llow;
+ u8 lhih;
+ u8 rsvd7[0x6];
+ /* Extended Mobile Access */
+ u8 emae; /* 0x78 - EMA enable */
+ u16 emap; /* 0x79 - EMA pointer */
+ u16 emal; /* 0x7a - EMA Length */
+ u8 rsvd8[0x5];
+ /* MEF */
+ u8 mefe; /* 0x82 - MEF enable */
+ u8 rsvd9[0x9];
+ /* TPM support */
+ u8 tpmp; /* 0x8c - TPM */
+ u8 tpme;
+ u8 rsvd10[8];
+ /* SATA */
+ u8 gtf0[7]; /* 0x96 - GTF task file buffer for port 0 */
+ u8 gtf1[7];
+ u8 gtf2[7];
+ u8 idem;
+ u8 idet;
+ u8 rsvd11[7];
+ /* IGD OpRegion (not implemented yet) */
+ u32 aslb; /* 0xb4 - IGD OpRegion Base Address */
+ u8 ibtt; /* 0xb8 - IGD boot type */
+ u8 ipat; /* 0xb9 - IGD panel type */
+ u8 itvf; /* 0xba - IGD TV format */
+ u8 itvm; /* 0xbb - IGD TV minor format */
+ u8 ipsc; /* 0xbc - IGD Panel Scaling */
+ u8 iblc; /* 0xbd - IGD BLC configuration */
+ u8 ibia; /* 0xbe - IGD BIA configuration */
+ u8 issc; /* 0xbf - IGD SSC configuration */
+ u8 i409; /* 0xc0 - IGD 0409 modified settings */
+ u8 i509; /* 0xc1 - IGD 0509 modified settings */
+ u8 i609; /* 0xc2 - IGD 0609 modified settings */
+ u8 i709; /* 0xc3 - IGD 0709 modified settings */
+ u8 idmm; /* 0xc4 - IGD Power Conservation */
+ u8 idms; /* 0xc5 - IGD DVMT memory size */
+ u8 if1e; /* 0xc6 - IGD Function 1 Enable */
+ u8 hvco; /* 0xc7 - IGD HPLL VCO */
+ u32 nxd[8]; /* 0xc8 - IGD next state DIDx for _DGS */
+ u8 isci; /* 0xe8 - IGD SMI/SCI mode (0: SCI) */
+ u8 pavp; /* 0xe9 - IGD PAVP data */
+ u8 rsvd12; /* 0xea - rsvd */
+ u8 oscc; /* 0xeb - PCIe OSC control */
+ u8 npce; /* 0xec - native pcie support */
+ u8 plfl; /* 0xed - platform flavor */
+ u8 brev; /* 0xee - board revision */
+ u8 dpbm; /* 0xef - digital port b mode */
+ u8 dpcm; /* 0xf0 - digital port c mode */
+ u8 dpdm; /* 0xf1 - digital port c mode */
+ u8 alfp; /* 0xf2 - active lfp */
+ u8 imon; /* 0xf3 - current graphics turbo imon value */
+ u8 mmio; /* 0xf4 - 64bit mmio support */
+ u8 rsvd13[11]; /* 0xf5 - rsvd */
+
+ /* ChromeOS specific (starts at 0x100)*/
+ chromeos_acpi_t chromeos;
+} __attribute__((packed)) global_nvs_t;
+
+#ifdef __SMM__
+/* Used in SMM to find the ACPI GNVS address */
+global_nvs_t *smm_get_gnvs(void);
+#endif
diff --git a/src/southbridge/intel/lynxpoint/pch.c b/src/southbridge/intel/lynxpoint/pch.c
new file mode 100644
index 0000000..c4a3acf
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/pch.c
@@ -0,0 +1,383 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ * Copyright (C) 2012 The Chromium OS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <delay.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include "pch.h"
+
+static int pch_revision_id = -1;
+static int pch_type = -1;
+
+int pch_silicon_revision(void)
+{
+ if (pch_revision_id < 0)
+ pch_revision_id = pci_read_config8(
+ dev_find_slot(0, PCI_DEVFN(0x1f, 0)),
+ PCI_REVISION_ID);
+ return pch_revision_id;
+}
+
+int pch_silicon_type(void)
+{
+ if (pch_type < 0)
+ pch_type = pci_read_config8(
+ dev_find_slot(0, PCI_DEVFN(0x1f, 0)),
+ PCI_DEVICE_ID + 1);
+ return pch_type;
+}
+
+int pch_silicon_supported(int type, int rev)
+{
+ return 1;
+}
+
+/* Set bit in Function Disble register to hide this device */
+static void pch_hide_devfn(unsigned devfn)
+{
+ switch (devfn) {
+ case PCI_DEVFN(22, 0): /* MEI #1 */
+ RCBA32_OR(FD2, PCH_DISABLE_MEI1);
+ break;
+ case PCI_DEVFN(22, 1): /* MEI #2 */
+ RCBA32_OR(FD2, PCH_DISABLE_MEI2);
+ break;
+ case PCI_DEVFN(22, 2): /* IDE-R */
+ RCBA32_OR(FD2, PCH_DISABLE_IDER);
+ break;
+ case PCI_DEVFN(22, 3): /* KT */
+ RCBA32_OR(FD2, PCH_DISABLE_KT);
+ break;
+ case PCI_DEVFN(25, 0): /* Gigabit Ethernet */
+ RCBA32_OR(BUC, PCH_DISABLE_GBE);
+ break;
+ case PCI_DEVFN(26, 0): /* EHCI #2 */
+ RCBA32_OR(FD, PCH_DISABLE_EHCI2);
+ break;
+ case PCI_DEVFN(27, 0): /* HD Audio Controller */
+ RCBA32_OR(FD, PCH_DISABLE_HD_AUDIO);
+ break;
+ case PCI_DEVFN(28, 0): /* PCI Express Root Port 1 */
+ case PCI_DEVFN(28, 1): /* PCI Express Root Port 2 */
+ case PCI_DEVFN(28, 2): /* PCI Express Root Port 3 */
+ case PCI_DEVFN(28, 3): /* PCI Express Root Port 4 */
+ case PCI_DEVFN(28, 4): /* PCI Express Root Port 5 */
+ case PCI_DEVFN(28, 5): /* PCI Express Root Port 6 */
+ case PCI_DEVFN(28, 6): /* PCI Express Root Port 7 */
+ case PCI_DEVFN(28, 7): /* PCI Express Root Port 8 */
+ RCBA32_OR(FD, PCH_DISABLE_PCIE(PCI_FUNC(devfn)));
+ break;
+ case PCI_DEVFN(29, 0): /* EHCI #1 */
+ RCBA32_OR(FD, PCH_DISABLE_EHCI1);
+ break;
+ case PCI_DEVFN(30, 0): /* PCI-to-PCI Bridge */
+ RCBA32_OR(FD, PCH_DISABLE_P2P);
+ break;
+ case PCI_DEVFN(31, 0): /* LPC */
+ RCBA32_OR(FD, PCH_DISABLE_LPC);
+ break;
+ case PCI_DEVFN(31, 2): /* SATA #1 */
+ RCBA32_OR(FD, PCH_DISABLE_SATA1);
+ break;
+ case PCI_DEVFN(31, 3): /* SMBUS */
+ RCBA32_OR(FD, PCH_DISABLE_SMBUS);
+ break;
+ case PCI_DEVFN(31, 5): /* SATA #22 */
+ RCBA32_OR(FD, PCH_DISABLE_SATA2);
+ break;
+ case PCI_DEVFN(31, 6): /* Thermal Subsystem */
+ RCBA32_OR(FD, PCH_DISABLE_THERMAL);
+ break;
+ }
+}
+
+#define IOBP_RETRY 1000
+static inline int iobp_poll(void)
+{
+ unsigned try = IOBP_RETRY;
+ u32 data;
+
+ while (try--) {
+ data = RCBA32(IOBPS);
+ if ((data & 1) == 0)
+ return 1;
+ udelay(10);
+ }
+
+ printk(BIOS_ERR, "IOBP timeout\n");
+ return 0;
+}
+
+void pch_iobp_update(u32 address, u32 andvalue, u32 orvalue)
+{
+ u32 data;
+
+ /* Set the address */
+ RCBA32(IOBPIRI) = address;
+
+ /* READ OPCODE */
+ RCBA32(IOBPS) = IOBPS_RW_BX;
+ if (!iobp_poll())
+ return;
+
+ /* Read IOBP data */
+ data = RCBA32(IOBPD);
+ if (!iobp_poll())
+ return;
+
+ /* Check for successful transaction */
+ if ((RCBA32(IOBPS) & 0x6) != 0) {
+ printk(BIOS_ERR, "IOBP read 0x%08x failed\n", address);
+ return;
+ }
+
+ /* Update the data */
+ data &= andvalue;
+ data |= orvalue;
+
+ /* WRITE OPCODE */
+ RCBA32(IOBPS) = IOBPS_RW_BX;
+ if (!iobp_poll())
+ return;
+
+ /* Write IOBP data */
+ RCBA32(IOBPD) = data;
+ if (!iobp_poll())
+ return;
+}
+
+/* Check if any port in set X to X+3 is enabled */
+static int pch_pcie_check_set_enabled(device_t dev)
+{
+ device_t port;
+ int port_func;
+ int dev_func = PCI_FUNC(dev->path.pci.devfn);
+
+ printk(BIOS_DEBUG, "%s: check set enabled\n", dev_path(dev));
+
+ /* Go through static device tree list of devices
+ * because enumeration is still in progress */
+ for (port = all_devices; port; port = port->next) {
+ /* Only care about PCIe root ports */
+ if (PCI_SLOT(port->path.pci.devfn) !=
+ PCI_SLOT(dev->path.pci.devfn))
+ continue;
+
+ /* Check if port is in range and enabled */
+ port_func = PCI_FUNC(port->path.pci.devfn);
+ if (port_func >= dev_func &&
+ port_func < (dev_func + 4) &&
+ port->enabled)
+ return 1;
+ }
+
+ /* None of the ports in this set are enabled */
+ return 0;
+}
+
+/* RPFN is a write-once register so keep a copy until it is written */
+static u32 new_rpfn;
+
+/* Swap function numbers assigned to two PCIe Root Ports */
+static void pch_pcie_function_swap(u8 old_fn, u8 new_fn)
+{
+ u32 old_rpfn = new_rpfn;
+
+ printk(BIOS_DEBUG, "PCH: Remap PCIe function %d to %d\n",
+ old_fn, new_fn);
+
+ new_rpfn &= ~(RPFN_FNMASK(old_fn) | RPFN_FNMASK(new_fn));
+
+ /* Old function set to new function and disabled */
+ new_rpfn |= RPFN_FNSET(old_fn, RPFN_FNGET(old_rpfn, new_fn));
+ new_rpfn |= RPFN_FNSET(new_fn, RPFN_FNGET(old_rpfn, old_fn));
+}
+
+/* Update devicetree with new Root Port function number assignment */
+static void pch_pcie_devicetree_update(void)
+{
+ device_t dev;
+
+ /* Update the function numbers in the static devicetree */
+ for (dev = all_devices; dev; dev = dev->next) {
+ u8 new_devfn;
+
+ /* Only care about PCH PCIe root ports */
+ if (PCI_SLOT(dev->path.pci.devfn) !=
+ PCH_PCIE_DEV_SLOT)
+ continue;
+
+ /* Determine the new devfn for this port */
+ new_devfn = PCI_DEVFN(PCH_PCIE_DEV_SLOT,
+ RPFN_FNGET(new_rpfn,
+ PCI_FUNC(dev->path.pci.devfn)));
+
+ if (dev->path.pci.devfn != new_devfn) {
+ printk(BIOS_DEBUG,
+ "PCH: PCIe map %02x.%1x -> %02x.%1x\n",
+ PCI_SLOT(dev->path.pci.devfn),
+ PCI_FUNC(dev->path.pci.devfn),
+ PCI_SLOT(new_devfn), PCI_FUNC(new_devfn));
+
+ dev->path.pci.devfn = new_devfn;
+ }
+ }
+}
+
+/* Special handling for PCIe Root Port devices */
+static void pch_pcie_enable(device_t dev)
+{
+ struct southbridge_intel_lynxpoint_config *config = dev->chip_info;
+ u32 reg32;
+
+ /*
+ * Save a copy of the Root Port Function Number map when
+ * starting to walk the list of PCIe Root Ports so it can
+ * be updated locally and written out when the last port
+ * has been processed.
+ */
+ if (PCI_FUNC(dev->path.pci.devfn) == 0) {
+ new_rpfn = RCBA32(RPFN);
+
+ /*
+ * Enable Root Port coalescing if the first port is disabled
+ * or the other devices will not be enumerated by the OS.
+ */
+ if (!dev->enabled)
+ config->pcie_port_coalesce = 1;
+
+ if (config->pcie_port_coalesce)
+ printk(BIOS_INFO,
+ "PCH: PCIe Root Port coalescing is enabled\n");
+ }
+
+ if (!dev->enabled) {
+ printk(BIOS_DEBUG, "%s: Disabling device\n", dev_path(dev));
+
+ /*
+ * PCIE Power Savings for PantherPoint and CougarPoint/B1+
+ *
+ * If PCIe 0-3 disabled set Function 0 0xE2[0] = 1
+ * If PCIe 4-7 disabled set Function 4 0xE2[0] = 1
+ *
+ * This check is done here instead of pcie driver
+ * because the pcie driver enable() handler is not
+ * called unless the device is enabled.
+ */
+ if ((PCI_FUNC(dev->path.pci.devfn) == 0 ||
+ PCI_FUNC(dev->path.pci.devfn) == 4)) {
+ /* Handle workaround for PPT and CPT/B1+ */
+ if (!pch_pcie_check_set_enabled(dev)) {
+ u8 reg8 = pci_read_config8(dev, 0xe2);
+ reg8 |= 1;
+ pci_write_config8(dev, 0xe2, reg8);
+ }
+
+ /*
+ * Enable Clock Gating for shared PCIe resources
+ * before disabling this particular port.
+ */
+ pci_write_config8(dev, 0xe1, 0x3c);
+ }
+
+ /* Ensure memory, io, and bus master are all disabled */
+ reg32 = pci_read_config32(dev, PCI_COMMAND);
+ reg32 &= ~(PCI_COMMAND_MASTER |
+ PCI_COMMAND_MEMORY | PCI_COMMAND_IO);
+ pci_write_config32(dev, PCI_COMMAND, reg32);
+
+ /* Do not claim downstream transactions for PCIe ports */
+ new_rpfn |= RPFN_HIDE(PCI_FUNC(dev->path.pci.devfn));
+
+ /* Hide this device if possible */
+ pch_hide_devfn(dev->path.pci.devfn);
+ } else {
+ int fn;
+
+ /*
+ * Check if there is a lower disabled port to swap with this
+ * port in order to maintain linear order starting at zero.
+ */
+ if (config->pcie_port_coalesce) {
+ for (fn=0; fn < PCI_FUNC(dev->path.pci.devfn); fn++) {
+ if (!(new_rpfn & RPFN_HIDE(fn)))
+ continue;
+
+ /* Swap places with this function */
+ pch_pcie_function_swap(
+ PCI_FUNC(dev->path.pci.devfn), fn);
+ break;
+ }
+ }
+
+ /* Enable SERR */
+ reg32 = pci_read_config32(dev, PCI_COMMAND);
+ reg32 |= PCI_COMMAND_SERR;
+ pci_write_config32(dev, PCI_COMMAND, reg32);
+ }
+
+ /*
+ * When processing the last PCIe root port we can now
+ * update the Root Port Function Number and Hide register.
+ */
+ if (PCI_FUNC(dev->path.pci.devfn) == 7) {
+ printk(BIOS_SPEW, "PCH: RPFN 0x%08x -> 0x%08x\n",
+ RCBA32(RPFN), new_rpfn);
+ RCBA32(RPFN) = new_rpfn;
+
+ /* Update static devictree with new function numbers */
+ if (config->pcie_port_coalesce)
+ pch_pcie_devicetree_update();
+ }
+}
+
+void pch_enable(device_t dev)
+{
+ u32 reg32;
+
+ /* PCH PCIe Root Ports get special handling */
+ if (PCI_SLOT(dev->path.pci.devfn) == PCH_PCIE_DEV_SLOT)
+ return pch_pcie_enable(dev);
+
+ if (!dev->enabled) {
+ printk(BIOS_DEBUG, "%s: Disabling device\n", dev_path(dev));
+
+ /* Ensure memory, io, and bus master are all disabled */
+ reg32 = pci_read_config32(dev, PCI_COMMAND);
+ reg32 &= ~(PCI_COMMAND_MASTER |
+ PCI_COMMAND_MEMORY | PCI_COMMAND_IO);
+ pci_write_config32(dev, PCI_COMMAND, reg32);
+
+ /* Hide this device if possible */
+ pch_hide_devfn(dev->path.pci.devfn);
+ } else {
+ /* Enable SERR */
+ reg32 = pci_read_config32(dev, PCI_COMMAND);
+ reg32 |= PCI_COMMAND_SERR;
+ pci_write_config32(dev, PCI_COMMAND, reg32);
+ }
+}
+
+struct chip_operations southbridge_intel_lynxpoint_ops = {
+ CHIP_NAME("Intel Series 8 (Lynx Point) Southbridge")
+ .enable_dev = pch_enable,
+};
diff --git a/src/southbridge/intel/lynxpoint/pch.h b/src/southbridge/intel/lynxpoint/pch.h
new file mode 100644
index 0000000..d00ee62
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/pch.h
@@ -0,0 +1,591 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ * Copyright (C) 2012 The Chromium OS Authors. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#ifndef SOUTHBRIDGE_INTEL_LYNXPOINT_PCH_H
+#define SOUTHBRIDGE_INTEL_LYNXPOINT_PCH_H
+
+
+/*
+ * Lynx Point PCH PCI Devices:
+ *
+ * Bus 0:Device 31:Function 0 LPC Controller1
+ * Bus 0:Device 31:Function 2 SATA Controller #1
+ * Bus 0:Device 31:Function 3 SMBus Controller
+ * Bus 0:Device 31:Function 5 SATA Controller #22
+ * Bus 0:Device 31:Function 6 Thermal Subsystem
+ * Bus 0:Device 29:Function 03 USB EHCI Controller #1
+ * Bus 0:Device 26:Function 03 USB EHCI Controller #2
+ * Bus 0:Device 28:Function 0 PCI Express* Port 1
+ * Bus 0:Device 28:Function 1 PCI Express Port 2
+ * Bus 0:Device 28:Function 2 PCI Express Port 3
+ * Bus 0:Device 28:Function 3 PCI Express Port 4
+ * Bus 0:Device 28:Function 4 PCI Express Port 5
+ * Bus 0:Device 28:Function 5 PCI Express Port 6
+ * Bus 0:Device 28:Function 6 PCI Express Port 7
+ * Bus 0:Device 28:Function 7 PCI Express Port 8
+ * Bus 0:Device 27:Function 0 Intel® High Definition Audio Controller
+ * Bus 0:Device 25:Function 0 Gigabit Ethernet Controller
+ * Bus 0:Device 22:Function 0 Intel® Management Engine Interface #1
+ * Bus 0:Device 22:Function 1 Intel Management Engine Interface #2
+ * Bus 0:Device 22:Function 2 IDE-R
+ * Bus 0:Device 22:Function 3 KT
+ * Bus 0:Device 20:Function 0 xHCI Controller
+*/
+
+/* PCH types */
+
+/* PCH stepping values for LPC device */
+
+/*
+ * It does not matter where we put the SMBus I/O base, as long as we
+ * keep it consistent and don't interfere with other devices. Stage2
+ * will relocate this anyways.
+ * Our solution is to have SMB initialization move the I/O to SMBUS_IO_BASE
+ * again. But handling static BARs is a generic problem that should be
+ * solved in the device allocator.
+ */
+#define SMBUS_IO_BASE 0x0400
+#define SMBUS_SLAVE_ADDR 0x24
+/* TODO Make sure these don't get changed by stage2 */
+#define DEFAULT_GPIOBASE 0x0480
+#define DEFAULT_PMBASE 0x0500
+
+#define HPET_ADDR 0xfed00000
+#define DEFAULT_RCBA 0xfed1c000
+
+#ifndef __ACPI__
+#define DEBUG_PERIODIC_SMIS 0
+
+#if defined (__SMM__) && !defined(__ASSEMBLER__)
+void intel_pch_finalize_smm(void);
+#endif
+
+#if !defined(__ASSEMBLER__) && !defined(__ROMCC__)
+#if !defined(__PRE_RAM__) && !defined(__SMM__)
+#include <device/device.h>
+#include <arch/acpi.h>
+#include "chip.h"
+int pch_silicon_revision(void);
+int pch_silicon_type(void);
+int pch_silicon_supported(int type, int rev);
+void pch_enable(device_t dev);
+void pch_iobp_update(u32 address, u32 andvalue, u32 orvalue);
+#if CONFIG_ELOG
+void pch_log_state(void);
+#endif
+void acpi_create_intel_hpet(acpi_hpet_t * hpet);
+#else
+void enable_smbus(void);
+void enable_usb_bar(void);
+int smbus_read_byte(unsigned device, unsigned address);
+int early_spi_read(u32 offset, u32 size, u8 *buffer);
+#endif
+#endif
+
+#define MAINBOARD_POWER_OFF 0
+#define MAINBOARD_POWER_ON 1
+#define MAINBOARD_POWER_KEEP 2
+
+#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
+#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
+#endif
+
+/* PCI Configuration Space (D30:F0): PCI2PCI */
+#define PSTS 0x06
+#define SMLT 0x1b
+#define SECSTS 0x1e
+#define INTR 0x3c
+#define BCTRL 0x3e
+#define SBR (1 << 6)
+#define SEE (1 << 1)
+#define PERE (1 << 0)
+
+#define PCH_EHCI1_DEV PCI_DEV(0, 0x1d, 0)
+#define PCH_EHCI2_DEV PCI_DEV(0, 0x1a, 0)
+#define PCH_ME_DEV PCI_DEV(0, 0x16, 0)
+#define PCH_PCIE_DEV_SLOT 28
+
+/* PCI Configuration Space (D31:F0): LPC */
+#define PCH_LPC_DEV PCI_DEV(0, 0x1f, 0)
+#define SERIRQ_CNTL 0x64
+
+#define GEN_PMCON_1 0xa0
+#define GEN_PMCON_2 0xa2
+#define GEN_PMCON_3 0xa4
+#define ETR3 0xac
+#define ETR3_CWORWRE (1 << 18)
+#define ETR3_CF9GR (1 << 20)
+
+/* GEN_PMCON_3 bits */
+#define RTC_BATTERY_DEAD (1 << 2)
+#define RTC_POWER_FAILED (1 << 1)
+#define SLEEP_AFTER_POWER_FAIL (1 << 0)
+
+#define PMBASE 0x40
+#define ACPI_CNTL 0x44
+#define BIOS_CNTL 0xDC
+#define GPIO_BASE 0x48 /* LPC GPIO Base Address Register */
+#define GPIO_CNTL 0x4C /* LPC GPIO Control Register */
+#define GPIO_ROUT 0xb8
+
+#define PIRQA_ROUT 0x60
+#define PIRQB_ROUT 0x61
+#define PIRQC_ROUT 0x62
+#define PIRQD_ROUT 0x63
+#define PIRQE_ROUT 0x68
+#define PIRQF_ROUT 0x69
+#define PIRQG_ROUT 0x6A
+#define PIRQH_ROUT 0x6B
+
+#define LPC_IO_DEC 0x80 /* IO Decode Ranges Register */
+#define LPC_EN 0x82 /* LPC IF Enables Register */
+#define CNF2_LPC_EN (1 << 13) /* 0x4e/0x4f */
+#define CNF1_LPC_EN (1 << 12) /* 0x2e/0x2f */
+#define MC_LPC_EN (1 << 11) /* 0x62/0x66 */
+#define KBC_LPC_EN (1 << 10) /* 0x60/0x64 */
+#define GAMEH_LPC_EN (1 << 9) /* 0x208/0x20f */
+#define GAMEL_LPC_EN (1 << 8) /* 0x200/0x207 */
+#define FDD_LPC_EN (1 << 3) /* LPC_IO_DEC[12] */
+#define LPT_LPC_EN (1 << 2) /* LPC_IO_DEC[9:8] */
+#define COMB_LPC_EN (1 << 1) /* LPC_IO_DEC[6:4] */
+#define COMA_LPC_EN (1 << 0) /* LPC_IO_DEC[2:0] */
+#define LPC_GEN1_DEC 0x84 /* LPC IF Generic Decode Range 1 */
+#define LPC_GEN2_DEC 0x88 /* LPC IF Generic Decode Range 2 */
+#define LPC_GEN3_DEC 0x8c /* LPC IF Generic Decode Range 3 */
+#define LPC_GEN4_DEC 0x90 /* LPC IF Generic Decode Range 4 */
+
+/* PCI Configuration Space (D31:F1): IDE */
+#define PCH_IDE_DEV PCI_DEV(0, 0x1f, 1)
+#define PCH_SATA_DEV PCI_DEV(0, 0x1f, 2)
+#define PCH_SATA2_DEV PCI_DEV(0, 0x1f, 5)
+#define INTR_LN 0x3c
+#define IDE_TIM_PRI 0x40 /* IDE timings, primary */
+#define IDE_DECODE_ENABLE (1 << 15)
+#define IDE_SITRE (1 << 14)
+#define IDE_ISP_5_CLOCKS (0 << 12)
+#define IDE_ISP_4_CLOCKS (1 << 12)
+#define IDE_ISP_3_CLOCKS (2 << 12)
+#define IDE_RCT_4_CLOCKS (0 << 8)
+#define IDE_RCT_3_CLOCKS (1 << 8)
+#define IDE_RCT_2_CLOCKS (2 << 8)
+#define IDE_RCT_1_CLOCKS (3 << 8)
+#define IDE_DTE1 (1 << 7)
+#define IDE_PPE1 (1 << 6)
+#define IDE_IE1 (1 << 5)
+#define IDE_TIME1 (1 << 4)
+#define IDE_DTE0 (1 << 3)
+#define IDE_PPE0 (1 << 2)
+#define IDE_IE0 (1 << 1)
+#define IDE_TIME0 (1 << 0)
+#define IDE_TIM_SEC 0x42 /* IDE timings, secondary */
+
+#define IDE_SDMA_CNT 0x48 /* Synchronous DMA control */
+#define IDE_SSDE1 (1 << 3)
+#define IDE_SSDE0 (1 << 2)
+#define IDE_PSDE1 (1 << 1)
+#define IDE_PSDE0 (1 << 0)
+
+#define IDE_SDMA_TIM 0x4a
+
+#define IDE_CONFIG 0x54 /* IDE I/O Configuration Register */
+#define SIG_MODE_SEC_NORMAL (0 << 18)
+#define SIG_MODE_SEC_TRISTATE (1 << 18)
+#define SIG_MODE_SEC_DRIVELOW (2 << 18)
+#define SIG_MODE_PRI_NORMAL (0 << 16)
+#define SIG_MODE_PRI_TRISTATE (1 << 16)
+#define SIG_MODE_PRI_DRIVELOW (2 << 16)
+#define FAST_SCB1 (1 << 15)
+#define FAST_SCB0 (1 << 14)
+#define FAST_PCB1 (1 << 13)
+#define FAST_PCB0 (1 << 12)
+#define SCB1 (1 << 3)
+#define SCB0 (1 << 2)
+#define PCB1 (1 << 1)
+#define PCB0 (1 << 0)
+
+#define SATA_SIRI 0xa0 /* SATA Indexed Register Index */
+#define SATA_SIRD 0xa4 /* SATA Indexed Register Data */
+#define SATA_SP 0xd0 /* Scratchpad */
+
+/* SATA IOBP Registers */
+#define SATA_IOBP_SP0G3IR 0xea000151
+#define SATA_IOBP_SP1G3IR 0xea000051
+
+/* PCI Configuration Space (D31:F3): SMBus */
+#define PCH_SMBUS_DEV PCI_DEV(0, 0x1f, 3)
+#define SMB_BASE 0x20
+#define HOSTC 0x40
+#define SMB_RCV_SLVA 0x09
+
+/* HOSTC bits */
+#define I2C_EN (1 << 2)
+#define SMB_SMI_EN (1 << 1)
+#define HST_EN (1 << 0)
+
+/* SMBus I/O bits. */
+#define SMBHSTSTAT 0x0
+#define SMBHSTCTL 0x2
+#define SMBHSTCMD 0x3
+#define SMBXMITADD 0x4
+#define SMBHSTDAT0 0x5
+#define SMBHSTDAT1 0x6
+#define SMBBLKDAT 0x7
+#define SMBTRNSADD 0x9
+#define SMBSLVDATA 0xa
+#define SMLINK_PIN_CTL 0xe
+#define SMBUS_PIN_CTL 0xf
+
+#define SMBUS_TIMEOUT (10 * 1000 * 100)
+
+
+/* Southbridge IO BARs */
+
+#define GPIOBASE 0x48
+
+#define PMBASE 0x40
+
+/* Root Complex Register Block */
+#define RCBA 0xf0
+
+#define RCBA8(x) *((volatile u8 *)(DEFAULT_RCBA + x))
+#define RCBA16(x) *((volatile u16 *)(DEFAULT_RCBA + x))
+#define RCBA32(x) *((volatile u32 *)(DEFAULT_RCBA + x))
+
+#define RCBA_AND_OR(bits, x, and, or) \
+ RCBA##bits(x) = ((RCBA##bits(x) & (and)) | (or))
+#define RCBA8_AND_OR(x, and, or) RCBA_AND_OR(8, x, and, or)
+#define RCBA16_AND_OR(x, and, or) RCBA_AND_OR(16, x, and, or)
+#define RCBA32_AND_OR(x, and, or) RCBA_AND_OR(32, x, and, or)
+#define RCBA32_OR(x, or) RCBA_AND_OR(32, x, ~0UL, or)
+
+#define VCH 0x0000 /* 32bit */
+#define VCAP1 0x0004 /* 32bit */
+#define VCAP2 0x0008 /* 32bit */
+#define PVC 0x000c /* 16bit */
+#define PVS 0x000e /* 16bit */
+
+#define V0CAP 0x0010 /* 32bit */
+#define V0CTL 0x0014 /* 32bit */
+#define V0STS 0x001a /* 16bit */
+
+#define V1CAP 0x001c /* 32bit */
+#define V1CTL 0x0020 /* 32bit */
+#define V1STS 0x0026 /* 16bit */
+
+#define RCTCL 0x0100 /* 32bit */
+#define ESD 0x0104 /* 32bit */
+#define ULD 0x0110 /* 32bit */
+#define ULBA 0x0118 /* 64bit */
+
+#define RP1D 0x0120 /* 32bit */
+#define RP1BA 0x0128 /* 64bit */
+#define RP2D 0x0130 /* 32bit */
+#define RP2BA 0x0138 /* 64bit */
+#define RP3D 0x0140 /* 32bit */
+#define RP3BA 0x0148 /* 64bit */
+#define RP4D 0x0150 /* 32bit */
+#define RP4BA 0x0158 /* 64bit */
+#define HDD 0x0160 /* 32bit */
+#define HDBA 0x0168 /* 64bit */
+#define RP5D 0x0170 /* 32bit */
+#define RP5BA 0x0178 /* 64bit */
+#define RP6D 0x0180 /* 32bit */
+#define RP6BA 0x0188 /* 64bit */
+
+#define RPFN 0x0404 /* 32bit */
+
+/* Root Port configuratinon space hide */
+#define RPFN_HIDE(port) (1 << (((port) * 4) + 3))
+/* Get the function number assigned to a Root Port */
+#define RPFN_FNGET(reg,port) (((reg) >> ((port) * 4)) & 7)
+/* Set the function number for a Root Port */
+#define RPFN_FNSET(port,func) (((func) & 7) << ((port) * 4))
+/* Root Port function number mask */
+#define RPFN_FNMASK(port) (7 << ((port) * 4))
+
+#define TRSR 0x1e00 /* 8bit */
+#define TRCR 0x1e10 /* 64bit */
+#define TWDR 0x1e18 /* 64bit */
+
+#define IOTR0 0x1e80 /* 64bit */
+#define IOTR1 0x1e88 /* 64bit */
+#define IOTR2 0x1e90 /* 64bit */
+#define IOTR3 0x1e98 /* 64bit */
+
+#define TCTL 0x3000 /* 8bit */
+
+#define NOINT 0
+#define INTA 1
+#define INTB 2
+#define INTC 3
+#define INTD 4
+
+#define DIR_IDR 12 /* Interrupt D Pin Offset */
+#define DIR_ICR 8 /* Interrupt C Pin Offset */
+#define DIR_IBR 4 /* Interrupt B Pin Offset */
+#define DIR_IAR 0 /* Interrupt A Pin Offset */
+
+#define PIRQA 0
+#define PIRQB 1
+#define PIRQC 2
+#define PIRQD 3
+#define PIRQE 4
+#define PIRQF 5
+#define PIRQG 6
+#define PIRQH 7
+
+/* IO Buffer Programming */
+#define IOBPIRI 0x2330
+#define IOBPD 0x2334
+#define IOBPS 0x2338
+#define IOBPS_RW_BX ((1 << 9)|(1 << 10))
+#define IOBPS_WRITE_AX ((1 << 9)|(1 << 10))
+#define IOBPS_READ_AX ((1 << 8)|(1 << 9)|(1 << 10))
+
+#define D31IP 0x3100 /* 32bit */
+#define D31IP_TTIP 24 /* Thermal Throttle Pin */
+#define D31IP_SIP2 20 /* SATA Pin 2 */
+#define D31IP_SMIP 12 /* SMBUS Pin */
+#define D31IP_SIP 8 /* SATA Pin */
+#define D30IP 0x3104 /* 32bit */
+#define D30IP_PIP 0 /* PCI Bridge Pin */
+#define D29IP 0x3108 /* 32bit */
+#define D29IP_E1P 0 /* EHCI #1 Pin */
+#define D28IP 0x310c /* 32bit */
+#define D28IP_P8IP 28 /* PCI Express Port 8 */
+#define D28IP_P7IP 24 /* PCI Express Port 7 */
+#define D28IP_P6IP 20 /* PCI Express Port 6 */
+#define D28IP_P5IP 16 /* PCI Express Port 5 */
+#define D28IP_P4IP 12 /* PCI Express Port 4 */
+#define D28IP_P3IP 8 /* PCI Express Port 3 */
+#define D28IP_P2IP 4 /* PCI Express Port 2 */
+#define D28IP_P1IP 0 /* PCI Express Port 1 */
+#define D27IP 0x3110 /* 32bit */
+#define D27IP_ZIP 0 /* HD Audio Pin */
+#define D26IP 0x3114 /* 32bit */
+#define D26IP_E2P 0 /* EHCI #2 Pin */
+#define D25IP 0x3118 /* 32bit */
+#define D25IP_LIP 0 /* GbE LAN Pin */
+#define D22IP 0x3124 /* 32bit */
+#define D22IP_KTIP 12 /* KT Pin */
+#define D22IP_IDERIP 8 /* IDE-R Pin */
+#define D22IP_MEI2IP 4 /* MEI #2 Pin */
+#define D22IP_MEI1IP 0 /* MEI #1 Pin */
+#define D31IR 0x3140 /* 16bit */
+#define D30IR 0x3142 /* 16bit */
+#define D29IR 0x3144 /* 16bit */
+#define D28IR 0x3146 /* 16bit */
+#define D27IR 0x3148 /* 16bit */
+#define D26IR 0x314c /* 16bit */
+#define D25IR 0x3150 /* 16bit */
+#define D22IR 0x315c /* 16bit */
+#define OIC 0x31fe /* 16bit */
+#define SOFT_RESET_CTRL 0x38f4
+#define SOFT_RESET_DATA 0x38f8
+
+#define DIR_ROUTE(x,a,b,c,d) \
+ RCBA32(x) = (((d) << DIR_IDR) | ((c) << DIR_ICR) | \
+ ((b) << DIR_IBR) | ((a) << DIR_IAR))
+
+#define RC 0x3400 /* 32bit */
+#define HPTC 0x3404 /* 32bit */
+#define GCS 0x3410 /* 32bit */
+#define BUC 0x3414 /* 32bit */
+#define PCH_DISABLE_GBE (1 << 5)
+#define FD 0x3418 /* 32bit */
+#define DISPBDF 0x3424 /* 16bit */
+#define FD2 0x3428 /* 32bit */
+#define CG 0x341c /* 32bit */
+
+/* Function Disable 1 RCBA 0x3418 */
+#define PCH_DISABLE_ALWAYS ((1 << 0)|(1 << 26)|(1 << 27))
+#define PCH_DISABLE_P2P (1 << 1)
+#define PCH_DISABLE_SATA1 (1 << 2)
+#define PCH_DISABLE_SMBUS (1 << 3)
+#define PCH_DISABLE_HD_AUDIO (1 << 4)
+#define PCH_DISABLE_EHCI2 (1 << 13)
+#define PCH_DISABLE_LPC (1 << 14)
+#define PCH_DISABLE_EHCI1 (1 << 15)
+#define PCH_DISABLE_PCIE(x) (1 << (16 + x))
+#define PCH_DISABLE_THERMAL (1 << 24)
+#define PCH_DISABLE_SATA2 (1 << 25)
+
+/* Function Disable 2 RCBA 0x3428 */
+#define PCH_DISABLE_KT (1 << 4)
+#define PCH_DISABLE_IDER (1 << 3)
+#define PCH_DISABLE_MEI2 (1 << 2)
+#define PCH_DISABLE_MEI1 (1 << 1)
+#define PCH_ENABLE_DBDF (1 << 0)
+
+/* ICH7 GPIOBASE */
+#define GPIO_USE_SEL 0x00
+#define GP_IO_SEL 0x04
+#define GP_LVL 0x0c
+#define GPO_BLINK 0x18
+#define GPI_INV 0x2c
+#define GPIO_USE_SEL2 0x30
+#define GP_IO_SEL2 0x34
+#define GP_LVL2 0x38
+#define GPIO_USE_SEL3 0x40
+#define GP_IO_SEL3 0x44
+#define GP_LVL3 0x48
+#define GP_RST_SEL1 0x60
+#define GP_RST_SEL2 0x64
+#define GP_RST_SEL3 0x68
+
+/* ICH7 PMBASE */
+#define PM1_STS 0x00
+#define WAK_STS (1 << 15)
+#define PCIEXPWAK_STS (1 << 14)
+#define PRBTNOR_STS (1 << 11)
+#define RTC_STS (1 << 10)
+#define PWRBTN_STS (1 << 8)
+#define GBL_STS (1 << 5)
+#define BM_STS (1 << 4)
+#define TMROF_STS (1 << 0)
+#define PM1_EN 0x02
+#define PCIEXPWAK_DIS (1 << 14)
+#define RTC_EN (1 << 10)
+#define PWRBTN_EN (1 << 8)
+#define GBL_EN (1 << 5)
+#define TMROF_EN (1 << 0)
+#define PM1_CNT 0x04
+#define SLP_EN (1 << 13)
+#define SLP_TYP (7 << 10)
+#define SLP_TYP_S0 0
+#define SLP_TYP_S1 1
+#define SLP_TYP_S3 5
+#define SLP_TYP_S4 6
+#define SLP_TYP_S5 7
+#define GBL_RLS (1 << 2)
+#define BM_RLD (1 << 1)
+#define SCI_EN (1 << 0)
+#define PM1_TMR 0x08
+#define PROC_CNT 0x10
+#define LV2 0x14
+#define LV3 0x15
+#define LV4 0x16
+#define PM2_CNT 0x50 // mobile only
+#define GPE0_STS 0x20
+#define PME_B0_STS (1 << 13)
+#define PME_STS (1 << 11)
+#define BATLOW_STS (1 << 10)
+#define PCI_EXP_STS (1 << 9)
+#define RI_STS (1 << 8)
+#define SMB_WAK_STS (1 << 7)
+#define TCOSCI_STS (1 << 6)
+#define SWGPE_STS (1 << 2)
+#define HOT_PLUG_STS (1 << 1)
+#define GPE0_EN 0x28
+#define PME_B0_EN (1 << 13)
+#define PME_EN (1 << 11)
+#define TCOSCI_EN (1 << 6)
+#define SMI_EN 0x30
+#define INTEL_USB2_EN (1 << 18) // Intel-Specific USB2 SMI logic
+#define LEGACY_USB2_EN (1 << 17) // Legacy USB2 SMI logic
+#define PERIODIC_EN (1 << 14) // SMI on PERIODIC_STS in SMI_STS
+#define TCO_EN (1 << 13) // Enable TCO Logic (BIOSWE et al)
+#define MCSMI_EN (1 << 11) // Trap microcontroller range access
+#define BIOS_RLS (1 << 7) // asserts SCI on bit set
+#define SWSMI_TMR_EN (1 << 6) // start software smi timer on bit set
+#define APMC_EN (1 << 5) // Writes to APM_CNT cause SMI#
+#define SLP_SMI_EN (1 << 4) // Write to SLP_EN in PM1_CNT asserts SMI#
+#define LEGACY_USB_EN (1 << 3) // Legacy USB circuit SMI logic
+#define BIOS_EN (1 << 2) // Assert SMI# on setting GBL_RLS bit
+#define EOS (1 << 1) // End of SMI (deassert SMI#)
+#define GBL_SMI_EN (1 << 0) // SMI# generation at all?
+#define SMI_STS 0x34
+#define ALT_GP_SMI_EN 0x38
+#define ALT_GP_SMI_STS 0x3a
+#define GPE_CNTL 0x42
+#define DEVACT_STS 0x44
+#define SS_CNT 0x50
+#define C3_RES 0x54
+#define TCO1_STS 0x64
+#define DMISCI_STS (1 << 9)
+#define TCO2_STS 0x66
+
+/*
+ * SPI Opcode Menu setup for SPIBAR lockdown
+ * should support most common flash chips.
+ */
+
+#define SPIBAR_OFFSET 0x3800
+#define SPIBAR8(x) RCBA8(x + SPIBAR_OFFSET)
+#define SPIBAR16(x) RCBA16(x + SPIBAR_OFFSET)
+#define SPIBAR32(x) RCBA32(x + SPIBAR_OFFSET)
+
+/* Reigsters within the SPIBAR */
+#define SSFC 0x91
+#define FDOC 0xb0
+#define FDOD 0xb4
+
+#define SPI_OPMENU_0 0x01 /* WRSR: Write Status Register */
+#define SPI_OPTYPE_0 0x01 /* Write, no address */
+
+#define SPI_OPMENU_1 0x02 /* BYPR: Byte Program */
+#define SPI_OPTYPE_1 0x03 /* Write, address required */
+
+#define SPI_OPMENU_2 0x03 /* READ: Read Data */
+#define SPI_OPTYPE_2 0x02 /* Read, address required */
+
+#define SPI_OPMENU_3 0x05 /* RDSR: Read Status Register */
+#define SPI_OPTYPE_3 0x00 /* Read, no address */
+
+#define SPI_OPMENU_4 0x20 /* SE20: Sector Erase 0x20 */
+#define SPI_OPTYPE_4 0x03 /* Write, address required */
+
+#define SPI_OPMENU_5 0x9f /* RDID: Read ID */
+#define SPI_OPTYPE_5 0x00 /* Read, no address */
+
+#define SPI_OPMENU_6 0xd8 /* BED8: Block Erase 0xd8 */
+#define SPI_OPTYPE_6 0x03 /* Write, address required */
+
+#define SPI_OPMENU_7 0x0b /* FAST: Fast Read */
+#define SPI_OPTYPE_7 0x02 /* Read, address required */
+
+#define SPI_OPMENU_UPPER ((SPI_OPMENU_7 << 24) | (SPI_OPMENU_6 << 16) | \
+ (SPI_OPMENU_5 << 8) | SPI_OPMENU_4)
+#define SPI_OPMENU_LOWER ((SPI_OPMENU_3 << 24) | (SPI_OPMENU_2 << 16) | \
+ (SPI_OPMENU_1 << 8) | SPI_OPMENU_0)
+
+#define SPI_OPTYPE ((SPI_OPTYPE_7 << 14) | (SPI_OPTYPE_6 << 12) | \
+ (SPI_OPTYPE_5 << 10) | (SPI_OPTYPE_4 << 8) | \
+ (SPI_OPTYPE_3 << 6) | (SPI_OPTYPE_2 << 4) | \
+ (SPI_OPTYPE_1 << 2) | (SPI_OPTYPE_0))
+
+#define SPI_OPPREFIX ((0x50 << 8) | 0x06) /* EWSR and WREN */
+
+#define SPIBAR_HSFS 0x3804 /* SPI hardware sequence status */
+#define SPIBAR_HSFS_SCIP (1 << 5) /* SPI Cycle In Progress */
+#define SPIBAR_HSFS_AEL (1 << 2) /* SPI Access Error Log */
+#define SPIBAR_HSFS_FCERR (1 << 1) /* SPI Flash Cycle Error */
+#define SPIBAR_HSFS_FDONE (1 << 0) /* SPI Flash Cycle Done */
+#define SPIBAR_HSFC 0x3806 /* SPI hardware sequence control */
+#define SPIBAR_HSFC_BYTE_COUNT(c) (((c - 1) & 0x3f) << 8)
+#define SPIBAR_HSFC_CYCLE_READ (0 << 1) /* Read cycle */
+#define SPIBAR_HSFC_CYCLE_WRITE (2 << 1) /* Write cycle */
+#define SPIBAR_HSFC_CYCLE_ERASE (3 << 1) /* Erase cycle */
+#define SPIBAR_HSFC_GO (1 << 0) /* GO: start SPI transaction */
+#define SPIBAR_FADDR 0x3808 /* SPI flash address */
+#define SPIBAR_FDATA(n) (0x3810 + (4 * n)) /* SPI flash data */
+
+#endif /* __ACPI__ */
+#endif /* SOUTHBRIDGE_INTEL_LYNXPOINT_PCH_H */
diff --git a/src/southbridge/intel/lynxpoint/pci.c b/src/southbridge/intel/lynxpoint/pci.c
new file mode 100644
index 0000000..306e7d5
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/pci.c
@@ -0,0 +1,145 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include "pch.h"
+
+static void pci_init(struct device *dev)
+{
+ u16 reg16;
+ u8 reg8;
+
+ printk(BIOS_DEBUG, "PCI init.\n");
+ /* Enable Bus Master */
+ reg16 = pci_read_config16(dev, PCI_COMMAND);
+ reg16 |= PCI_COMMAND_MASTER;
+ pci_write_config16(dev, PCI_COMMAND, reg16);
+
+ /* This device has no interrupt */
+ pci_write_config8(dev, INTR, 0xff);
+
+ /* disable parity error response and SERR */
+ reg16 = pci_read_config16(dev, BCTRL);
+ reg16 &= ~(1 << 0);
+ reg16 &= ~(1 << 1);
+ pci_write_config16(dev, BCTRL, reg16);
+
+ /* Master Latency Count must be set to 0x04! */
+ reg8 = pci_read_config8(dev, SMLT);
+ reg8 &= 0x07;
+ reg8 |= (0x04 << 3);
+ pci_write_config8(dev, SMLT, reg8);
+
+ /* Will this improve throughput of bus masters? */
+ pci_write_config8(dev, PCI_MIN_GNT, 0x06);
+
+ /* Clear errors in status registers */
+ reg16 = pci_read_config16(dev, PSTS);
+ //reg16 |= 0xf900;
+ pci_write_config16(dev, PSTS, reg16);
+
+ reg16 = pci_read_config16(dev, SECSTS);
+ // reg16 |= 0xf900;
+ pci_write_config16(dev, SECSTS, reg16);
+}
+
+#undef PCI_BRIDGE_UPDATE_COMMAND
+static void ich_pci_dev_enable_resources(struct device *dev)
+{
+ const struct pci_operations *ops;
+ uint16_t command;
+
+ /* Set the subsystem vendor and device id for mainboard devices */
+ ops = ops_pci(dev);
+ if (dev->on_mainboard && ops && ops->set_subsystem) {
+ printk(BIOS_DEBUG, "%s subsystem <- %02x/%02x\n",
+ dev_path(dev),
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
+ ops->set_subsystem(dev,
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_VENDOR_ID,
+ CONFIG_MAINBOARD_PCI_SUBSYSTEM_DEVICE_ID);
+ }
+
+ command = pci_read_config16(dev, PCI_COMMAND);
+ command |= dev->command;
+#ifdef PCI_BRIDGE_UPDATE_COMMAND
+ /* If we write to PCI_COMMAND, on some systems
+ * this will cause the ROM and APICs not being visible
+ * anymore.
+ */
+ printk(BIOS_DEBUG, "%s cmd <- %02x\n", dev_path(dev), command);
+ pci_write_config16(dev, PCI_COMMAND, command);
+#else
+ printk(BIOS_DEBUG, "%s cmd <- %02x (NOT WRITTEN!)\n", dev_path(dev), command);
+#endif
+}
+
+static void ich_pci_bus_enable_resources(struct device *dev)
+{
+ uint16_t ctrl;
+ /* enable IO in command register if there is VGA card
+ * connected with (even it does not claim IO resource)
+ */
+ if (dev->link_list->bridge_ctrl & PCI_BRIDGE_CTL_VGA)
+ dev->command |= PCI_COMMAND_IO;
+ ctrl = pci_read_config16(dev, PCI_BRIDGE_CONTROL);
+ ctrl |= dev->link_list->bridge_ctrl;
+ ctrl |= (PCI_BRIDGE_CTL_PARITY + PCI_BRIDGE_CTL_SERR); /* error check */
+ printk(BIOS_DEBUG, "%s bridge ctrl <- %04x\n", dev_path(dev), ctrl);
+ pci_write_config16(dev, PCI_BRIDGE_CONTROL, ctrl);
+
+ /* This is the reason we need our own pci_bus_enable_resources */
+ ich_pci_dev_enable_resources(dev);
+}
+
+static void set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ /* NOTE: This is not the default position! */
+ if (!vendor || !device) {
+ pci_write_config32(dev, 0x54,
+ pci_read_config32(dev, PCI_VENDOR_ID));
+ } else {
+ pci_write_config32(dev, 0x54,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+ }
+}
+
+static struct pci_operations pci_ops = {
+ .set_subsystem = set_subsystem,
+};
+
+static struct device_operations device_ops = {
+ .read_resources = pci_bus_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = ich_pci_bus_enable_resources,
+ .init = pci_init,
+ .scan_bus = pci_scan_bridge,
+ .ops_pci = &pci_ops,
+};
+
+static const struct pci_driver pch_pci __pci_driver = {
+ .ops = &device_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = 0x2448,
+};
diff --git a/src/southbridge/intel/lynxpoint/pcie.c b/src/southbridge/intel/lynxpoint/pcie.c
new file mode 100644
index 0000000..80cd355
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/pcie.c
@@ -0,0 +1,273 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pciexp.h>
+#include <device/pci_ids.h>
+#include "pch.h"
+
+static void pch_pcie_pm_early(struct device *dev)
+{
+/* RPC has been moved. It is in PCI config space now. */
+#if 0
+ u16 link_width_p0, link_width_p4;
+ u8 slot_power_limit = 10; /* 10W for x1 */
+ u32 reg32;
+ u8 reg8;
+
+ reg32 = RCBA32(RPC);
+
+ /* Port 0-3 link aggregation from PCIEPCS1[1:0] soft strap */
+ switch (reg32 & 3) {
+ case 3:
+ link_width_p0 = 4;
+ break;
+ case 1:
+ case 2:
+ link_width_p0 = 2;
+ break;
+ case 0:
+ default:
+ link_width_p0 = 1;
+ }
+
+ /* Port 4-7 link aggregation from PCIEPCS2[1:0] soft strap */
+ switch ((reg32 >> 2) & 3) {
+ case 3:
+ link_width_p4 = 4;
+ break;
+ case 1:
+ case 2:
+ link_width_p4 = 2;
+ break;
+ case 0:
+ default:
+ link_width_p4 = 1;
+ }
+
+ /* Enable dynamic clock gating where needed */
+ reg8 = pci_read_config8(dev, 0xe1);
+ switch (PCI_FUNC(dev->path.pci.devfn)) {
+ case 0: /* Port 0 */
+ if (link_width_p0 == 4)
+ slot_power_limit = 40; /* 40W for x4 */
+ else if (link_width_p0 == 2)
+ slot_power_limit = 20; /* 20W for x2 */
+ reg8 |= 0x3f;
+ break;
+ case 4: /* Port 4 */
+ if (link_width_p4 == 4)
+ slot_power_limit = 40; /* 40W for x4 */
+ else if (link_width_p4 == 2)
+ slot_power_limit = 20; /* 20W for x2 */
+ reg8 |= 0x3f;
+ break;
+ case 1: /* Port 1 only if Port 0 is x1 */
+ if (link_width_p0 == 1)
+ reg8 |= 0x3;
+ break;
+ case 2: /* Port 2 only if Port 0 is x1 or x2 */
+ case 3: /* Port 3 only if Port 0 is x1 or x2 */
+ if (link_width_p0 <= 2)
+ reg8 |= 0x3;
+ break;
+ case 5: /* Port 5 only if Port 4 is x1 */
+ if (link_width_p4 == 1)
+ reg8 |= 0x3;
+ break;
+ case 6: /* Port 7 only if Port 4 is x1 or x2 */
+ case 7: /* Port 7 only if Port 4 is x1 or x2 */
+ if (link_width_p4 <= 2)
+ reg8 |= 0x3;
+ break;
+ }
+ pci_write_config8(dev, 0xe1, reg8);
+
+ /* Set 0xE8[0] = 1 */
+ reg32 = pci_read_config32(dev, 0xe8);
+ reg32 |= 1;
+ pci_write_config32(dev, 0xe8, reg32);
+
+ /* Adjust Common Clock exit latency */
+ reg32 = pci_read_config32(dev, 0xd8);
+ reg32 &= ~(1 << 17);
+ reg32 |= (1 << 16) | (1 << 15);
+ reg32 &= ~(1 << 31); /* Disable PME# SCI for native PME handling */
+ pci_write_config32(dev, 0xd8, reg32);
+
+ /* Adjust ASPM L1 exit latency */
+ reg32 = pci_read_config32(dev, 0x4c);
+ reg32 &= ~((1 << 17) | (1 << 16) | (1 << 15));
+ if (RCBA32(0x2320) & (1 << 16)) {
+ /* If RCBA+2320[15]=1 set ASPM L1 to 8-16us */
+ reg32 |= (1 << 17);
+ } else {
+ /* Else set ASPM L1 to 2-4us */
+ reg32 |= (1 << 16);
+ }
+ pci_write_config32(dev, 0x4c, reg32);
+
+ /* Set slot power limit as configured above */
+ reg32 = pci_read_config32(dev, 0x54);
+ reg32 &= ~((1 << 15) | (1 << 16)); /* 16:15 = Slot power scale */
+ reg32 &= ~(0xff << 7); /* 14:7 = Slot power limit */
+ reg32 |= (slot_power_limit << 7);
+ pci_write_config32(dev, 0x54, reg32);
+#endif
+}
+
+static void pch_pcie_pm_late(struct device *dev)
+{
+ enum aspm_type apmc;
+ u32 reg32;
+
+ /* Set 0x314 = 0x743a361b */
+ pci_mmio_write_config32(dev, 0x314, 0x743a361b);
+
+ /* Set 0x318[31:16] = 0x1414 */
+ reg32 = pci_mmio_read_config32(dev, 0x318);
+ reg32 &= 0x0000ffff;
+ reg32 |= 0x14140000;
+ pci_mmio_write_config32(dev, 0x318, reg32);
+
+ /* Set 0x324[5] = 1 */
+ reg32 = pci_mmio_read_config32(dev, 0x324);
+ reg32 |= (1 << 5);
+ pci_mmio_write_config32(dev, 0x324, reg32);
+
+ /* Set 0x330[7:0] = 0x40 */
+ reg32 = pci_mmio_read_config32(dev, 0x330);
+ reg32 &= ~(0xff);
+ reg32 |= 0x40;
+ pci_mmio_write_config32(dev, 0x330, reg32);
+
+ /* Set 0x33C[24:0] = 0x854c74 */
+ reg32 = pci_mmio_read_config32(dev, 0x33c);
+ reg32 &= 0xff000000;
+ reg32 |= 0x00854c74;
+ pci_mmio_write_config32(dev, 0x33c, reg32);
+
+ /* No IO-APIC, Disable EOI forwarding */
+ reg32 = pci_read_config32(dev, 0xd4);
+ reg32 |= (1 << 1);
+ pci_write_config32(dev, 0xd4, reg32);
+
+ /* Get configured ASPM state */
+ apmc = pci_read_config32(dev, 0x50) & 3;
+
+ /* If both L0s and L1 enabled then set root port 0xE8[1]=1 */
+ if (apmc == PCIE_ASPM_BOTH) {
+ reg32 = pci_read_config32(dev, 0xe8);
+ reg32 |= (1 << 1);
+ pci_write_config32(dev, 0xe8, reg32);
+ }
+}
+
+static void pci_init(struct device *dev)
+{
+ u16 reg16;
+ u32 reg32;
+
+ printk(BIOS_DEBUG, "Initializing PCH PCIe bridge.\n");
+
+ /* Enable Bus Master */
+ reg32 = pci_read_config32(dev, PCI_COMMAND);
+ reg32 |= PCI_COMMAND_MASTER;
+ pci_write_config32(dev, PCI_COMMAND, reg32);
+
+ /* Set Cache Line Size to 0x10 */
+ // This has no effect but the OS might expect it
+ pci_write_config8(dev, 0x0c, 0x10);
+
+ reg16 = pci_read_config16(dev, 0x3e);
+ reg16 &= ~(1 << 0); /* disable parity error response */
+ // reg16 &= ~(1 << 1); /* disable SERR */
+ reg16 |= (1 << 2); /* ISA enable */
+ pci_write_config16(dev, 0x3e, reg16);
+
+#ifdef EVEN_MORE_DEBUG
+ reg32 = pci_read_config32(dev, 0x20);
+ printk(BIOS_SPEW, " MBL = 0x%08x\n", reg32);
+ reg32 = pci_read_config32(dev, 0x24);
+ printk(BIOS_SPEW, " PMBL = 0x%08x\n", reg32);
+ reg32 = pci_read_config32(dev, 0x28);
+ printk(BIOS_SPEW, " PMBU32 = 0x%08x\n", reg32);
+ reg32 = pci_read_config32(dev, 0x2c);
+ printk(BIOS_SPEW, " PMLU32 = 0x%08x\n", reg32);
+#endif
+
+ /* Clear errors in status registers */
+ reg16 = pci_read_config16(dev, 0x06);
+ //reg16 |= 0xf900;
+ pci_write_config16(dev, 0x06, reg16);
+
+ reg16 = pci_read_config16(dev, 0x1e);
+ //reg16 |= 0xf900;
+ pci_write_config16(dev, 0x1e, reg16);
+
+ /* Power Management init after enumeration */
+ pch_pcie_pm_late(dev);
+}
+
+static void pch_pcie_enable(device_t dev)
+{
+ /* Power Management init before enumeration */
+ pch_pcie_pm_early(dev);
+}
+
+static void pcie_set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ /* NOTE: This is not the default position! */
+ if (!vendor || !device) {
+ pci_write_config32(dev, 0x94,
+ pci_read_config32(dev, 0));
+ } else {
+ pci_write_config32(dev, 0x94,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+ }
+}
+
+static struct pci_operations pci_ops = {
+ .set_subsystem = pcie_set_subsystem,
+};
+
+static struct device_operations device_ops = {
+ .read_resources = pci_bus_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_bus_enable_resources,
+ .init = pci_init,
+ .enable = pch_pcie_enable,
+ .scan_bus = pciexp_scan_bridge,
+ .ops_pci = &pci_ops,
+};
+
+static const unsigned short pci_device_ids[] = { 0x1c10, 0x1c12, 0x1c14, 0x1c16,
+ 0x1c18, 0x1c1a, 0x1c1c, 0x1c1e,
+ 0x1e10, 0x1e12, 0x1e14, 0x1e16,
+ 0x1e18, 0x1e1a, 0x1e1c, 0x1e1e,
+ 0 };
+
+static const struct pci_driver pch_pcie __pci_driver = {
+ .ops = &device_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .devices = pci_device_ids,
+};
diff --git a/src/southbridge/intel/lynxpoint/reset.c b/src/southbridge/intel/lynxpoint/reset.c
new file mode 100644
index 0000000..429aad0
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/reset.c
@@ -0,0 +1,32 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <reset.h>
+
+void soft_reset(void)
+{
+ outb(0x04, 0xcf9);
+}
+
+void hard_reset(void)
+{
+ outb(0x06, 0xcf9);
+}
diff --git a/src/southbridge/intel/lynxpoint/sata.c b/src/southbridge/intel/lynxpoint/sata.c
new file mode 100644
index 0000000..0761323
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/sata.c
@@ -0,0 +1,290 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <arch/io.h>
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include "pch.h"
+
+typedef struct southbridge_intel_lynxpoint_config config_t;
+
+static inline u32 sir_read(struct device *dev, int idx)
+{
+ pci_write_config32(dev, SATA_SIRI, idx);
+ return pci_read_config32(dev, SATA_SIRD);
+}
+
+static inline void sir_write(struct device *dev, int idx, u32 value)
+{
+ pci_write_config32(dev, SATA_SIRI, idx);
+ pci_write_config32(dev, SATA_SIRD, value);
+}
+
+static void sata_init(struct device *dev)
+{
+ u32 reg32;
+ u16 reg16;
+ /* Get the chip configuration */
+ config_t *config = dev->chip_info;
+
+ printk(BIOS_DEBUG, "SATA: Initializing...\n");
+
+ if (config == NULL) {
+ printk(BIOS_ERR, "SATA: ERROR: Device not in devicetree.cb!\n");
+ return;
+ }
+
+ /* SATA configuration */
+
+ /* Enable BARs */
+ pci_write_config16(dev, PCI_COMMAND, 0x0007);
+
+ if (config->ide_legacy_combined) {
+ printk(BIOS_DEBUG, "SATA: Controller in combined mode.\n");
+
+ /* No AHCI: clear AHCI base */
+ pci_write_config32(dev, 0x24, 0x00000000);
+ /* And without AHCI BAR no memory decoding */
+ reg16 = pci_read_config16(dev, PCI_COMMAND);
+ reg16 &= ~PCI_COMMAND_MEMORY;
+ pci_write_config16(dev, PCI_COMMAND, reg16);
+
+ pci_write_config8(dev, 0x09, 0x80);
+
+ /* Set timings */
+ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+ IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
+ pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+ IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
+ IDE_PPE0 | IDE_IE0 | IDE_TIME0);
+
+ /* Sync DMA */
+ pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0);
+ pci_write_config16(dev, IDE_SDMA_TIM, 0x0200);
+
+ /* Set IDE I/O Configuration */
+ reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
+ pci_write_config32(dev, IDE_CONFIG, reg32);
+
+ /* Port enable */
+ reg16 = pci_read_config16(dev, 0x92);
+ reg16 &= ~0x3f;
+ reg16 |= config->sata_port_map;
+ pci_write_config16(dev, 0x92, reg16);
+
+ /* SATA Initialization register */
+ pci_write_config32(dev, 0x94,
+ ((config->sata_port_map ^ 0x3f) << 24) | 0x183);
+ } else if(config->sata_ahci) {
+ u32 abar;
+
+ printk(BIOS_DEBUG, "SATA: Controller in AHCI mode.\n");
+
+ /* Set Interrupt Line */
+ /* Interrupt Pin is set by D31IP.PIP */
+ pci_write_config8(dev, INTR_LN, 0x0a);
+
+ /* Set timings */
+ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+ IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
+ IDE_PPE0 | IDE_IE0 | IDE_TIME0);
+ pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+ IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
+
+ /* Sync DMA */
+ pci_write_config16(dev, IDE_SDMA_CNT, IDE_PSDE0);
+ pci_write_config16(dev, IDE_SDMA_TIM, 0x0001);
+
+ /* Set IDE I/O Configuration */
+ reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
+ pci_write_config32(dev, IDE_CONFIG, reg32);
+
+ /* for AHCI, Port Enable is managed in memory mapped space */
+ reg16 = pci_read_config16(dev, 0x92);
+ reg16 &= ~0x3f; /* 6 ports SKU + ORM */
+ reg16 |= 0x8000 | config->sata_port_map;
+ pci_write_config16(dev, 0x92, reg16);
+
+ /* SATA Initialization register */
+ pci_write_config32(dev, 0x94,
+ ((config->sata_port_map ^ 0x3f) << 24) | 0x183);
+
+ /* Initialize AHCI memory-mapped space */
+ abar = pci_read_config32(dev, PCI_BASE_ADDRESS_5);
+ printk(BIOS_DEBUG, "ABAR: %08X\n", abar);
+ /* CAP (HBA Capabilities) : enable power management */
+ reg32 = read32(abar + 0x00);
+ reg32 |= 0x0c006000; // set PSC+SSC+SALP+SSS
+ reg32 &= ~0x00020060; // clear SXS+EMS+PMS
+ write32(abar + 0x00, reg32);
+ /* PI (Ports implemented) */
+ write32(abar + 0x0c, config->sata_port_map);
+ (void) read32(abar + 0x0c); /* Read back 1 */
+ (void) read32(abar + 0x0c); /* Read back 2 */
+ /* CAP2 (HBA Capabilities Extended)*/
+ reg32 = read32(abar + 0x24);
+ reg32 &= ~0x00000002;
+ write32(abar + 0x24, reg32);
+ /* VSP (Vendor Specific Register */
+ reg32 = read32(abar + 0xa0);
+ reg32 &= ~0x00000005;
+ write32(abar + 0xa0, reg32);
+ } else {
+ printk(BIOS_DEBUG, "SATA: Controller in plain mode.\n");
+
+ /* No AHCI: clear AHCI base */
+ pci_write_config32(dev, 0x24, 0x00000000);
+
+ /* And without AHCI BAR no memory decoding */
+ reg16 = pci_read_config16(dev, PCI_COMMAND);
+ reg16 &= ~PCI_COMMAND_MEMORY;
+ pci_write_config16(dev, PCI_COMMAND, reg16);
+
+ /* Native mode capable on both primary and secondary (0xa)
+ * or'ed with enabled (0x50) = 0xf
+ */
+ pci_write_config8(dev, 0x09, 0x8f);
+
+ /* Set Interrupt Line */
+ /* Interrupt Pin is set by D31IP.PIP */
+ pci_write_config8(dev, INTR_LN, 0xff);
+
+ /* Set timings */
+ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+ IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
+ IDE_PPE0 | IDE_IE0 | IDE_TIME0);
+ pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+ IDE_SITRE | IDE_ISP_3_CLOCKS |
+ IDE_RCT_1_CLOCKS | IDE_IE0 | IDE_TIME0);
+
+ /* Sync DMA */
+ pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0 | IDE_PSDE0);
+ pci_write_config16(dev, IDE_SDMA_TIM, 0x0201);
+
+ /* Set IDE I/O Configuration */
+ reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
+ pci_write_config32(dev, IDE_CONFIG, reg32);
+
+ /* Port enable */
+ reg16 = pci_read_config16(dev, 0x92);
+ reg16 &= ~0x3f;
+ reg16 |= config->sata_port_map;
+ pci_write_config16(dev, 0x92, reg16);
+
+ /* SATA Initialization register */
+ pci_write_config32(dev, 0x94,
+ ((config->sata_port_map ^ 0x3f) << 24) | 0x183);
+ }
+
+ /* Set Gen3 Transmitter settings if needed */
+ if (config->sata_port0_gen3_tx)
+ pch_iobp_update(SATA_IOBP_SP0G3IR, 0,
+ config->sata_port0_gen3_tx);
+
+ if (config->sata_port1_gen3_tx)
+ pch_iobp_update(SATA_IOBP_SP1G3IR, 0,
+ config->sata_port1_gen3_tx);
+
+ /* Additional Programming Requirements */
+ sir_write(dev, 0x04, 0x00001600);
+ sir_write(dev, 0x28, 0xa0000033);
+ reg32 = sir_read(dev, 0x54);
+ reg32 &= 0xff000000;
+ reg32 |= 0x5555aa;
+ sir_write(dev, 0x54, reg32);
+ sir_write(dev, 0x64, 0xcccc8484);
+ reg32 = sir_read(dev, 0x68);
+ reg32 &= 0xffff0000;
+ reg32 |= 0xcccc;
+ sir_write(dev, 0x68, reg32);
+ reg32 = sir_read(dev, 0x78);
+ reg32 &= 0x0000ffff;
+ reg32 |= 0x88880000;
+ sir_write(dev, 0x78, reg32);
+ sir_write(dev, 0x84, 0x001c7000);
+ sir_write(dev, 0x88, 0x88338822);
+ sir_write(dev, 0xa0, 0x001c7000);
+ // a4
+ sir_write(dev, 0xc4, 0x0c0c0c0c);
+ sir_write(dev, 0xc8, 0x0c0c0c0c);
+ sir_write(dev, 0xd4, 0x10000000);
+
+ pch_iobp_update(0xea004001, 0x3fffffff, 0xc0000000);
+ pch_iobp_update(0xea00408a, 0xfffffcff, 0x00000100);
+}
+
+static void sata_enable(device_t dev)
+{
+ /* Get the chip configuration */
+ config_t *config = dev->chip_info;
+ u16 map = 0;
+
+ if (!config)
+ return;
+
+ /*
+ * Set SATA controller mode early so the resource allocator can
+ * properly assign IO/Memory resources for the controller.
+ */
+ if (config->sata_ahci)
+ map = 0x0060;
+
+ map |= (config->sata_port_map ^ 0x3f) << 8;
+
+ pci_write_config16(dev, 0x90, map);
+}
+
+static void sata_set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ if (!vendor || !device) {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ pci_read_config32(dev, PCI_VENDOR_ID));
+ } else {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+ }
+}
+
+static struct pci_operations sata_pci_ops = {
+ .set_subsystem = sata_set_subsystem,
+};
+
+static struct device_operations sata_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = sata_init,
+ .enable = sata_enable,
+ .scan_bus = 0,
+ .ops_pci = &sata_pci_ops,
+};
+
+static const unsigned short pci_device_ids[] = { 0x1c00, 0x1c01, 0x1c02, 0x1c03,
+ 0x1e00, 0x1e01, 0x1e02, 0x1e03,
+ 0 };
+
+static const struct pci_driver pch_sata __pci_driver = {
+ .ops = &sata_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .devices = pci_device_ids,
+};
+
diff --git a/src/southbridge/intel/lynxpoint/smbus.c b/src/southbridge/intel/lynxpoint/smbus.c
new file mode 100644
index 0000000..4786d8b
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/smbus.c
@@ -0,0 +1,109 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/path.h>
+#include <device/smbus.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include <device/pci_ops.h>
+#include <arch/io.h>
+#include "pch.h"
+#include "smbus.h"
+
+static void pch_smbus_init(device_t dev)
+{
+ struct resource *res;
+ u16 reg16;
+
+ /* Enable clock gating */
+ reg16 = pci_read_config32(dev, 0x80);
+ reg16 &= ~((1 << 8)|(1 << 10)|(1 << 12)|(1 << 14));
+ pci_write_config32(dev, 0x80, reg16);
+
+ /* Set Receive Slave Address */
+ res = find_resource(dev, PCI_BASE_ADDRESS_4);
+ if (res)
+ outb(SMBUS_SLAVE_ADDR, res->base + SMB_RCV_SLVA);
+}
+
+static int lsmbus_read_byte(device_t dev, u8 address)
+{
+ u16 device;
+ struct resource *res;
+ struct bus *pbus;
+
+ device = dev->path.i2c.device;
+ pbus = get_pbus_smbus(dev);
+ res = find_resource(pbus->dev, 0x20);
+
+ return do_smbus_read_byte(res->base, device, address);
+}
+
+static struct smbus_bus_operations lops_smbus_bus = {
+ .read_byte = lsmbus_read_byte,
+};
+
+static void smbus_set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ if (!vendor || !device) {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ pci_read_config32(dev, PCI_VENDOR_ID));
+ } else {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+ }
+}
+
+static struct pci_operations smbus_pci_ops = {
+ .set_subsystem = smbus_set_subsystem,
+};
+
+static void smbus_read_resources(device_t dev)
+{
+ struct resource *res = new_resource(dev, PCI_BASE_ADDRESS_4);
+ res->base = SMBUS_IO_BASE;
+ res->size = 32;
+ res->limit = res->base + res->size - 1;
+ res->flags = IORESOURCE_IO | IORESOURCE_FIXED | IORESOURCE_RESERVE |
+ IORESOURCE_STORED | IORESOURCE_ASSIGNED;
+
+ /* Also add MMIO resource */
+ res = pci_get_resource(dev, PCI_BASE_ADDRESS_0);
+}
+
+static struct device_operations smbus_ops = {
+ .read_resources = smbus_read_resources,
+ .set_resources = pci_dev_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .scan_bus = scan_static_bus,
+ .init = pch_smbus_init,
+ .ops_smbus_bus = &lops_smbus_bus,
+ .ops_pci = &smbus_pci_ops,
+};
+
+static const unsigned short pci_device_ids[] = { 0x1c22, 0x1e22, 0 };
+
+static const struct pci_driver pch_smbus __pci_driver = {
+ .ops = &smbus_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .devices = pci_device_ids,
+};
diff --git a/src/southbridge/intel/lynxpoint/smbus.h b/src/southbridge/intel/lynxpoint/smbus.h
new file mode 100644
index 0000000..81e5949
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/smbus.h
@@ -0,0 +1,100 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2005 Yinghai Lu <yinghailu@gmail.com>
+ * Copyright (C) 2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <device/smbus_def.h>
+#include "pch.h"
+
+static void smbus_delay(void)
+{
+ inb(0x80);
+}
+
+static int smbus_wait_until_ready(u16 smbus_base)
+{
+ unsigned loops = SMBUS_TIMEOUT;
+ unsigned char byte;
+ do {
+ smbus_delay();
+ if (--loops == 0)
+ break;
+ byte = inb(smbus_base + SMBHSTSTAT);
+ } while (byte & 1);
+ return loops ? 0 : -1;
+}
+
+static int smbus_wait_until_done(u16 smbus_base)
+{
+ unsigned loops = SMBUS_TIMEOUT;
+ unsigned char byte;
+ do {
+ smbus_delay();
+ if (--loops == 0)
+ break;
+ byte = inb(smbus_base + SMBHSTSTAT);
+ } while ((byte & 1) || (byte & ~((1 << 6) | (1 << 0))) == 0);
+ return loops ? 0 : -1;
+}
+
+static int do_smbus_read_byte(unsigned smbus_base, unsigned device, unsigned address)
+{
+ unsigned char global_status_register;
+ unsigned char byte;
+
+ if (smbus_wait_until_ready(smbus_base) < 0) {
+ return SMBUS_WAIT_UNTIL_READY_TIMEOUT;
+ }
+ /* Setup transaction */
+ /* Disable interrupts */
+ outb(inb(smbus_base + SMBHSTCTL) & (~1), smbus_base + SMBHSTCTL);
+ /* Set the device I'm talking too */
+ outb(((device & 0x7f) << 1) | 1, smbus_base + SMBXMITADD);
+ /* Set the command/address... */
+ outb(address & 0xff, smbus_base + SMBHSTCMD);
+ /* Set up for a byte data read */
+ outb((inb(smbus_base + SMBHSTCTL) & 0xe3) | (0x2 << 2),
+ (smbus_base + SMBHSTCTL));
+ /* Clear any lingering errors, so the transaction will run */
+ outb(inb(smbus_base + SMBHSTSTAT), smbus_base + SMBHSTSTAT);
+
+ /* Clear the data byte... */
+ outb(0, smbus_base + SMBHSTDAT0);
+
+ /* Start the command */
+ outb((inb(smbus_base + SMBHSTCTL) | 0x40),
+ smbus_base + SMBHSTCTL);
+
+ /* Poll for transaction completion */
+ if (smbus_wait_until_done(smbus_base) < 0) {
+ return SMBUS_WAIT_UNTIL_DONE_TIMEOUT;
+ }
+
+ global_status_register = inb(smbus_base + SMBHSTSTAT);
+
+ /* Ignore the "In Use" status... */
+ global_status_register &= ~(3 << 5);
+
+ /* Read results of transaction */
+ byte = inb(smbus_base + SMBHSTDAT0);
+ if (global_status_register != (1 << 1)) {
+ return SMBUS_ERROR;
+ }
+ return byte;
+}
+
diff --git a/src/southbridge/intel/lynxpoint/smi.c b/src/southbridge/intel/lynxpoint/smi.c
new file mode 100644
index 0000000..0bb9881
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/smi.c
@@ -0,0 +1,416 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+
+#include <device/device.h>
+#include <device/pci.h>
+#include <console/console.h>
+#include <arch/io.h>
+#include <cpu/cpu.h>
+#include <cpu/x86/cache.h>
+#include <cpu/x86/smm.h>
+#include <string.h>
+#include "pch.h"
+
+#if CONFIG_NORTHBRIDGE_INTEL_HASWELL
+#include "northbridge/intel/haswell/haswell.h"
+#endif
+
+extern unsigned char _binary_smm_start;
+extern unsigned char _binary_smm_size;
+
+/* While we read PMBASE dynamically in case it changed, let's
+ * initialize it with a sane value
+ */
+static u16 pmbase = DEFAULT_PMBASE;
+
+/**
+ * @brief read and clear PM1_STS
+ * @return PM1_STS register
+ */
+static u16 reset_pm1_status(void)
+{
+ u16 reg16;
+
+ reg16 = inw(pmbase + PM1_STS);
+ /* set status bits are cleared by writing 1 to them */
+ outw(reg16, pmbase + PM1_STS);
+
+ return reg16;
+}
+
+static void dump_pm1_status(u16 pm1_sts)
+{
+ printk(BIOS_DEBUG, "PM1_STS: ");
+ if (pm1_sts & (1 << 15)) printk(BIOS_DEBUG, "WAK ");
+ if (pm1_sts & (1 << 14)) printk(BIOS_DEBUG, "PCIEXPWAK ");
+ if (pm1_sts & (1 << 11)) printk(BIOS_DEBUG, "PRBTNOR ");
+ if (pm1_sts & (1 << 10)) printk(BIOS_DEBUG, "RTC ");
+ if (pm1_sts & (1 << 8)) printk(BIOS_DEBUG, "PWRBTN ");
+ if (pm1_sts & (1 << 5)) printk(BIOS_DEBUG, "GBL ");
+ if (pm1_sts & (1 << 4)) printk(BIOS_DEBUG, "BM ");
+ if (pm1_sts & (1 << 0)) printk(BIOS_DEBUG, "TMROF ");
+ printk(BIOS_DEBUG, "\n");
+}
+
+/**
+ * @brief read and clear SMI_STS
+ * @return SMI_STS register
+ */
+static u32 reset_smi_status(void)
+{
+ u32 reg32;
+
+ reg32 = inl(pmbase + SMI_STS);
+ /* set status bits are cleared by writing 1 to them */
+ outl(reg32, pmbase + SMI_STS);
+
+ return reg32;
+}
+
+static void dump_smi_status(u32 smi_sts)
+{
+ printk(BIOS_DEBUG, "SMI_STS: ");
+ if (smi_sts & (1 << 26)) printk(BIOS_DEBUG, "SPI ");
+ if (smi_sts & (1 << 25)) printk(BIOS_DEBUG, "EL_SMI ");
+ if (smi_sts & (1 << 21)) printk(BIOS_DEBUG, "MONITOR ");
+ if (smi_sts & (1 << 20)) printk(BIOS_DEBUG, "PCI_EXP_SMI ");
+ if (smi_sts & (1 << 18)) printk(BIOS_DEBUG, "INTEL_USB2 ");
+ if (smi_sts & (1 << 17)) printk(BIOS_DEBUG, "LEGACY_USB2 ");
+ if (smi_sts & (1 << 16)) printk(BIOS_DEBUG, "SMBUS_SMI ");
+ if (smi_sts & (1 << 15)) printk(BIOS_DEBUG, "SERIRQ_SMI ");
+ if (smi_sts & (1 << 14)) printk(BIOS_DEBUG, "PERIODIC ");
+ if (smi_sts & (1 << 13)) printk(BIOS_DEBUG, "TCO ");
+ if (smi_sts & (1 << 12)) printk(BIOS_DEBUG, "DEVMON ");
+ if (smi_sts & (1 << 11)) printk(BIOS_DEBUG, "MCSMI ");
+ if (smi_sts & (1 << 10)) printk(BIOS_DEBUG, "GPI ");
+ if (smi_sts & (1 << 9)) printk(BIOS_DEBUG, "GPE0 ");
+ if (smi_sts & (1 << 8)) printk(BIOS_DEBUG, "PM1 ");
+ if (smi_sts & (1 << 6)) printk(BIOS_DEBUG, "SWSMI_TMR ");
+ if (smi_sts & (1 << 5)) printk(BIOS_DEBUG, "APM ");
+ if (smi_sts & (1 << 4)) printk(BIOS_DEBUG, "SLP_SMI ");
+ if (smi_sts & (1 << 3)) printk(BIOS_DEBUG, "LEGACY_USB ");
+ if (smi_sts & (1 << 2)) printk(BIOS_DEBUG, "BIOS ");
+ printk(BIOS_DEBUG, "\n");
+}
+
+
+/**
+ * @brief read and clear GPE0_STS
+ * @return GPE0_STS register
+ */
+static u32 reset_gpe0_status(void)
+{
+ u32 reg32;
+
+ reg32 = inl(pmbase + GPE0_STS);
+ /* set status bits are cleared by writing 1 to them */
+ outl(reg32, pmbase + GPE0_STS);
+
+ return reg32;
+}
+
+static void dump_gpe0_status(u32 gpe0_sts)
+{
+ int i;
+ printk(BIOS_DEBUG, "GPE0_STS: ");
+ for (i=31; i<= 16; i--) {
+ if (gpe0_sts & (1 << i)) printk(BIOS_DEBUG, "GPIO%d ", (i-16));
+ }
+ if (gpe0_sts & (1 << 14)) printk(BIOS_DEBUG, "USB4 ");
+ if (gpe0_sts & (1 << 13)) printk(BIOS_DEBUG, "PME_B0 ");
+ if (gpe0_sts & (1 << 12)) printk(BIOS_DEBUG, "USB3 ");
+ if (gpe0_sts & (1 << 11)) printk(BIOS_DEBUG, "PME ");
+ if (gpe0_sts & (1 << 10)) printk(BIOS_DEBUG, "EL_SCI/BATLOW ");
+ if (gpe0_sts & (1 << 9)) printk(BIOS_DEBUG, "PCI_EXP ");
+ if (gpe0_sts & (1 << 8)) printk(BIOS_DEBUG, "RI ");
+ if (gpe0_sts & (1 << 7)) printk(BIOS_DEBUG, "SMB_WAK ");
+ if (gpe0_sts & (1 << 6)) printk(BIOS_DEBUG, "TCO_SCI ");
+ if (gpe0_sts & (1 << 5)) printk(BIOS_DEBUG, "AC97 ");
+ if (gpe0_sts & (1 << 4)) printk(BIOS_DEBUG, "USB2 ");
+ if (gpe0_sts & (1 << 3)) printk(BIOS_DEBUG, "USB1 ");
+ if (gpe0_sts & (1 << 2)) printk(BIOS_DEBUG, "HOT_PLUG ");
+ if (gpe0_sts & (1 << 0)) printk(BIOS_DEBUG, "THRM ");
+ printk(BIOS_DEBUG, "\n");
+}
+
+
+/**
+ * @brief read and clear ALT_GP_SMI_STS
+ * @return ALT_GP_SMI_STS register
+ */
+static u16 reset_alt_gp_smi_status(void)
+{
+ u16 reg16;
+
+ reg16 = inl(pmbase + ALT_GP_SMI_STS);
+ /* set status bits are cleared by writing 1 to them */
+ outl(reg16, pmbase + ALT_GP_SMI_STS);
+
+ return reg16;
+}
+
+static void dump_alt_gp_smi_status(u16 alt_gp_smi_sts)
+{
+ int i;
+ printk(BIOS_DEBUG, "ALT_GP_SMI_STS: ");
+ for (i=15; i<= 0; i--) {
+ if (alt_gp_smi_sts & (1 << i)) printk(BIOS_DEBUG, "GPI%d ", (i-16));
+ }
+ printk(BIOS_DEBUG, "\n");
+}
+
+
+
+/**
+ * @brief read and clear TCOx_STS
+ * @return TCOx_STS registers
+ */
+static u32 reset_tco_status(void)
+{
+ u32 tcobase = pmbase + 0x60;
+ u32 reg32;
+
+ reg32 = inl(tcobase + 0x04);
+ /* set status bits are cleared by writing 1 to them */
+ outl(reg32 & ~(1<<18), tcobase + 0x04); // Don't clear BOOT_STS before SECOND_TO_STS
+ if (reg32 & (1 << 18))
+ outl(reg32 & (1<<18), tcobase + 0x04); // clear BOOT_STS
+
+ return reg32;
+}
+
+
+static void dump_tco_status(u32 tco_sts)
+{
+ printk(BIOS_DEBUG, "TCO_STS: ");
+ if (tco_sts & (1 << 20)) printk(BIOS_DEBUG, "SMLINK_SLV ");
+ if (tco_sts & (1 << 18)) printk(BIOS_DEBUG, "BOOT ");
+ if (tco_sts & (1 << 17)) printk(BIOS_DEBUG, "SECOND_TO ");
+ if (tco_sts & (1 << 16)) printk(BIOS_DEBUG, "INTRD_DET ");
+ if (tco_sts & (1 << 12)) printk(BIOS_DEBUG, "DMISERR ");
+ if (tco_sts & (1 << 10)) printk(BIOS_DEBUG, "DMISMI ");
+ if (tco_sts & (1 << 9)) printk(BIOS_DEBUG, "DMISCI ");
+ if (tco_sts & (1 << 8)) printk(BIOS_DEBUG, "BIOSWR ");
+ if (tco_sts & (1 << 7)) printk(BIOS_DEBUG, "NEWCENTURY ");
+ if (tco_sts & (1 << 3)) printk(BIOS_DEBUG, "TIMEOUT ");
+ if (tco_sts & (1 << 2)) printk(BIOS_DEBUG, "TCO_INT ");
+ if (tco_sts & (1 << 1)) printk(BIOS_DEBUG, "SW_TCO ");
+ if (tco_sts & (1 << 0)) printk(BIOS_DEBUG, "NMI2SMI ");
+ printk(BIOS_DEBUG, "\n");
+}
+
+
+
+/**
+ * @brief Set the EOS bit
+ */
+static void smi_set_eos(void)
+{
+ u8 reg8;
+
+ reg8 = inb(pmbase + SMI_EN);
+ reg8 |= EOS;
+ outb(reg8, pmbase + SMI_EN);
+}
+
+extern uint8_t smm_relocation_start, smm_relocation_end;
+
+static void smm_relocate(void)
+{
+ u32 smi_en;
+ u16 pm1_en;
+ u32 gpe0_en;
+
+ printk(BIOS_DEBUG, "Initializing SMM handler...");
+
+ pmbase = pci_read_config32(dev_find_slot(0, PCI_DEVFN(0x1f, 0)),
+ PMBASE) & 0xff80;
+
+ printk(BIOS_SPEW, " ... pmbase = 0x%04x\n", pmbase);
+
+ smi_en = inl(pmbase + SMI_EN);
+ if (smi_en & APMC_EN) {
+ printk(BIOS_INFO, "SMI# handler already enabled?\n");
+ return;
+ }
+
+ /* copy the SMM relocation code */
+ memcpy((void *)0x38000, &smm_relocation_start,
+ &smm_relocation_end - &smm_relocation_start);
+
+ printk(BIOS_DEBUG, "\n");
+ dump_smi_status(reset_smi_status());
+ dump_pm1_status(reset_pm1_status());
+ dump_gpe0_status(reset_gpe0_status());
+ dump_alt_gp_smi_status(reset_alt_gp_smi_status());
+ dump_tco_status(reset_tco_status());
+
+ /* Disable GPE0 PME_B0 */
+ gpe0_en = inl(pmbase + GPE0_EN);
+ gpe0_en &= ~PME_B0_EN;
+ outl(gpe0_en, pmbase + GPE0_EN);
+
+ pm1_en = 0;
+ pm1_en |= PWRBTN_EN;
+ pm1_en |= GBL_EN;
+ outw(pm1_en, pmbase + PM1_EN);
+
+ /* Enable SMI generation:
+ * - on TCO events
+ * - on APMC writes (io 0xb2)
+ * - on writes to SLP_EN (sleep states)
+ * - on writes to GBL_RLS (bios commands)
+ * No SMIs:
+ * - on microcontroller writes (io 0x62/0x66)
+ */
+
+ smi_en = 0; /* reset SMI enables */
+
+#if 0
+ smi_en |= LEGACY_USB2_EN | LEGACY_USB_EN;
+#endif
+ smi_en |= TCO_EN;
+ smi_en |= APMC_EN;
+#if DEBUG_PERIODIC_SMIS
+ /* Set DEBUG_PERIODIC_SMIS in pch.h to debug using
+ * periodic SMIs.
+ */
+ smi_en |= PERIODIC_EN;
+#endif
+ smi_en |= SLP_SMI_EN;
+#if 0
+ smi_en |= BIOS_EN;
+#endif
+
+ /* The following need to be on for SMIs to happen */
+ smi_en |= EOS | GBL_SMI_EN;
+
+ outl(smi_en, pmbase + SMI_EN);
+
+ /**
+ * There are several methods of raising a controlled SMI# via
+ * software, among them:
+ * - Writes to io 0xb2 (APMC)
+ * - Writes to the Local Apic ICR with Delivery mode SMI.
+ *
+ * Using the local apic is a bit more tricky. According to
+ * AMD Family 11 Processor BKDG no destination shorthand must be
+ * used.
+ * The whole SMM initialization is quite a bit hardware specific, so
+ * I'm not too worried about the better of the methods at the moment
+ */
+
+ /* raise an SMI interrupt */
+ printk(BIOS_SPEW, " ... raise SMI#\n");
+ outb(0x00, 0xb2);
+}
+
+static int smm_handler_copied = 0;
+
+static void smm_install(void)
+{
+ device_t dev = dev_find_slot(0, PCI_DEVFN(0, 0));
+ u32 smm_base = 0xa0000;
+ struct ied_header ied = {
+ .signature = "INTEL RSVD",
+ .size = IED_SIZE,
+ .reserved = {0},
+ };
+
+ /* The first CPU running this gets to copy the SMM handler. But not all
+ * of them.
+ */
+ if (smm_handler_copied)
+ return;
+ smm_handler_copied = 1;
+
+ /* enable the SMM memory window */
+ pci_write_config8(dev, SMRAM, D_OPEN | G_SMRAME | C_BASE_SEG);
+
+#if CONFIG_SMM_TSEG
+ smm_base = pci_read_config32(dev, TSEG) & ~1;
+#endif
+
+ /* copy the real SMM handler */
+ printk(BIOS_DEBUG, "Installing SMM handler to 0x%08x\n", smm_base);
+ memcpy((void *)smm_base, &_binary_smm_start, (size_t)&_binary_smm_size);
+
+ /* copy the IED header into place */
+ if (CONFIG_SMM_TSEG_SIZE > IED_SIZE) {
+ /* Top of TSEG region */
+ smm_base += CONFIG_SMM_TSEG_SIZE - IED_SIZE;
+ printk(BIOS_DEBUG, "Installing IED header to 0x%08x\n",
+ smm_base);
+ memcpy((void *)smm_base, &ied, sizeof(ied));
+ }
+ wbinvd();
+
+ /* close the SMM memory window and enable normal SMM */
+ pci_write_config8(dev, SMRAM, G_SMRAME | C_BASE_SEG);
+}
+
+void smm_init(void)
+{
+#if CONFIG_ELOG
+ /* Log events from chipset before clearing */
+ pch_log_state();
+#endif
+
+ /* Put SMM code to 0xa0000 */
+ smm_install();
+
+ /* Put relocation code to 0x38000 and relocate SMBASE */
+ smm_relocate();
+
+ /* We're done. Make sure SMIs can happen! */
+ smi_set_eos();
+}
+
+void smm_lock(void)
+{
+ /* LOCK the SMM memory window and enable normal SMM.
+ * After running this function, only a full reset can
+ * make the SMM registers writable again.
+ */
+ printk(BIOS_DEBUG, "Locking SMM.\n");
+ pci_write_config8(dev_find_slot(0, PCI_DEVFN(0, 0)), SMRAM,
+ D_LCK | G_SMRAME | C_BASE_SEG);
+}
+
+void smm_setup_structures(void *gnvs, void *tcg, void *smi1)
+{
+ /*
+ * Issue SMI to set the gnvs pointer in SMM.
+ * tcg and smi1 are unused.
+ *
+ * EAX = APM_CNT_GNVS_UPDATE
+ * EBX = gnvs pointer
+ * EDX = APM_CNT
+ */
+ asm volatile (
+ "outb %%al, %%dx\n\t"
+ : /* ignore result */
+ : "a" (APM_CNT_GNVS_UPDATE),
+ "b" ((u32)gnvs),
+ "d" (APM_CNT)
+ );
+}
diff --git a/src/southbridge/intel/lynxpoint/smihandler.c b/src/southbridge/intel/lynxpoint/smihandler.c
new file mode 100644
index 0000000..c5c2c3e
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/smihandler.c
@@ -0,0 +1,801 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <types.h>
+#include <arch/hlt.h>
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <console/console.h>
+#include <cpu/x86/cache.h>
+#include <device/pci_def.h>
+#include <cpu/x86/smm.h>
+#include <elog.h>
+#include <pc80/mc146818rtc.h>
+#include "pch.h"
+
+#include "nvs.h"
+
+/* We are using PCIe accesses for now
+ * 1. the chipset can do it
+ * 2. we don't need to worry about how we leave 0xcf8/0xcfc behind
+ */
+#include <northbridge/intel/haswell/haswell.h>
+#include <northbridge/intel/haswell/pcie_config.c>
+
+/* While we read PMBASE dynamically in case it changed, let's
+ * initialize it with a sane value
+ */
+static u16 pmbase = DEFAULT_PMBASE;
+u16 smm_get_pmbase(void)
+{
+ return pmbase;
+}
+
+static u8 smm_initialized = 0;
+
+/* GNVS needs to be updated by an 0xEA PM Trap (B2) after it has been located
+ * by coreboot.
+ */
+static global_nvs_t *gnvs = (global_nvs_t *)0x0;
+global_nvs_t *smm_get_gnvs(void)
+{
+ return gnvs;
+}
+
+#if CONFIG_SMM_TSEG
+static u32 tseg_base = 0;
+u32 smi_get_tseg_base(void)
+{
+ if (!tseg_base)
+ tseg_base = pcie_read_config32(PCI_DEV(0, 0, 0), TSEG) & ~1;
+ return tseg_base;
+}
+void tseg_relocate(void **ptr)
+{
+ /* Adjust pointer with TSEG base */
+ if (*ptr && *ptr < (void*)smi_get_tseg_base())
+ *ptr = (void *)(((u8*)*ptr) + smi_get_tseg_base());
+}
+#endif
+
+/**
+ * @brief read and clear PM1_STS
+ * @return PM1_STS register
+ */
+static u16 reset_pm1_status(void)
+{
+ u16 reg16;
+
+ reg16 = inw(pmbase + PM1_STS);
+ /* set status bits are cleared by writing 1 to them */
+ outw(reg16, pmbase + PM1_STS);
+
+ return reg16;
+}
+
+static void dump_pm1_status(u16 pm1_sts)
+{
+ printk(BIOS_SPEW, "PM1_STS: ");
+ if (pm1_sts & (1 << 15)) printk(BIOS_SPEW, "WAK ");
+ if (pm1_sts & (1 << 14)) printk(BIOS_SPEW, "PCIEXPWAK ");
+ if (pm1_sts & (1 << 11)) printk(BIOS_SPEW, "PRBTNOR ");
+ if (pm1_sts & (1 << 10)) printk(BIOS_SPEW, "RTC ");
+ if (pm1_sts & (1 << 8)) printk(BIOS_SPEW, "PWRBTN ");
+ if (pm1_sts & (1 << 5)) printk(BIOS_SPEW, "GBL ");
+ if (pm1_sts & (1 << 4)) printk(BIOS_SPEW, "BM ");
+ if (pm1_sts & (1 << 0)) printk(BIOS_SPEW, "TMROF ");
+ printk(BIOS_SPEW, "\n");
+ int reg16 = inw(pmbase + PM1_EN);
+ printk(BIOS_SPEW, "PM1_EN: %x\n", reg16);
+}
+
+/**
+ * @brief read and clear SMI_STS
+ * @return SMI_STS register
+ */
+static u32 reset_smi_status(void)
+{
+ u32 reg32;
+
+ reg32 = inl(pmbase + SMI_STS);
+ /* set status bits are cleared by writing 1 to them */
+ outl(reg32, pmbase + SMI_STS);
+
+ return reg32;
+}
+
+static void dump_smi_status(u32 smi_sts)
+{
+ printk(BIOS_DEBUG, "SMI_STS: ");
+ if (smi_sts & (1 << 26)) printk(BIOS_DEBUG, "SPI ");
+ if (smi_sts & (1 << 21)) printk(BIOS_DEBUG, "MONITOR ");
+ if (smi_sts & (1 << 20)) printk(BIOS_DEBUG, "PCI_EXP_SMI ");
+ if (smi_sts & (1 << 18)) printk(BIOS_DEBUG, "INTEL_USB2 ");
+ if (smi_sts & (1 << 17)) printk(BIOS_DEBUG, "LEGACY_USB2 ");
+ if (smi_sts & (1 << 16)) printk(BIOS_DEBUG, "SMBUS_SMI ");
+ if (smi_sts & (1 << 15)) printk(BIOS_DEBUG, "SERIRQ_SMI ");
+ if (smi_sts & (1 << 14)) printk(BIOS_DEBUG, "PERIODIC ");
+ if (smi_sts & (1 << 13)) printk(BIOS_DEBUG, "TCO ");
+ if (smi_sts & (1 << 12)) printk(BIOS_DEBUG, "DEVMON ");
+ if (smi_sts & (1 << 11)) printk(BIOS_DEBUG, "MCSMI ");
+ if (smi_sts & (1 << 10)) printk(BIOS_DEBUG, "GPI ");
+ if (smi_sts & (1 << 9)) printk(BIOS_DEBUG, "GPE0 ");
+ if (smi_sts & (1 << 8)) printk(BIOS_DEBUG, "PM1 ");
+ if (smi_sts & (1 << 6)) printk(BIOS_DEBUG, "SWSMI_TMR ");
+ if (smi_sts & (1 << 5)) printk(BIOS_DEBUG, "APM ");
+ if (smi_sts & (1 << 4)) printk(BIOS_DEBUG, "SLP_SMI ");
+ if (smi_sts & (1 << 3)) printk(BIOS_DEBUG, "LEGACY_USB ");
+ if (smi_sts & (1 << 2)) printk(BIOS_DEBUG, "BIOS ");
+ printk(BIOS_DEBUG, "\n");
+}
+
+
+/**
+ * @brief read and clear GPE0_STS
+ * @return GPE0_STS register
+ */
+static u32 reset_gpe0_status(void)
+{
+ u32 reg32;
+
+ reg32 = inl(pmbase + GPE0_STS);
+ /* set status bits are cleared by writing 1 to them */
+ outl(reg32, pmbase + GPE0_STS);
+
+ return reg32;
+}
+
+static void dump_gpe0_status(u32 gpe0_sts)
+{
+ int i;
+ printk(BIOS_DEBUG, "GPE0_STS: ");
+ for (i=31; i<= 16; i--) {
+ if (gpe0_sts & (1 << i)) printk(BIOS_DEBUG, "GPIO%d ", (i-16));
+ }
+ if (gpe0_sts & (1 << 14)) printk(BIOS_DEBUG, "USB4 ");
+ if (gpe0_sts & (1 << 13)) printk(BIOS_DEBUG, "PME_B0 ");
+ if (gpe0_sts & (1 << 12)) printk(BIOS_DEBUG, "USB3 ");
+ if (gpe0_sts & (1 << 11)) printk(BIOS_DEBUG, "PME ");
+ if (gpe0_sts & (1 << 10)) printk(BIOS_DEBUG, "BATLOW ");
+ if (gpe0_sts & (1 << 9)) printk(BIOS_DEBUG, "PCI_EXP ");
+ if (gpe0_sts & (1 << 8)) printk(BIOS_DEBUG, "RI ");
+ if (gpe0_sts & (1 << 7)) printk(BIOS_DEBUG, "SMB_WAK ");
+ if (gpe0_sts & (1 << 6)) printk(BIOS_DEBUG, "TCO_SCI ");
+ if (gpe0_sts & (1 << 5)) printk(BIOS_DEBUG, "AC97 ");
+ if (gpe0_sts & (1 << 4)) printk(BIOS_DEBUG, "USB2 ");
+ if (gpe0_sts & (1 << 3)) printk(BIOS_DEBUG, "USB1 ");
+ if (gpe0_sts & (1 << 2)) printk(BIOS_DEBUG, "SWGPE ");
+ if (gpe0_sts & (1 << 1)) printk(BIOS_DEBUG, "HOTPLUG ");
+ if (gpe0_sts & (1 << 0)) printk(BIOS_DEBUG, "THRM ");
+ printk(BIOS_DEBUG, "\n");
+}
+
+
+/**
+ * @brief read and clear TCOx_STS
+ * @return TCOx_STS registers
+ */
+static u32 reset_tco_status(void)
+{
+ u32 tcobase = pmbase + 0x60;
+ u32 reg32;
+
+ reg32 = inl(tcobase + 0x04);
+ /* set status bits are cleared by writing 1 to them */
+ outl(reg32 & ~(1<<18), tcobase + 0x04); // Don't clear BOOT_STS before SECOND_TO_STS
+ if (reg32 & (1 << 18))
+ outl(reg32 & (1<<18), tcobase + 0x04); // clear BOOT_STS
+
+ return reg32;
+}
+
+
+static void dump_tco_status(u32 tco_sts)
+{
+ printk(BIOS_DEBUG, "TCO_STS: ");
+ if (tco_sts & (1 << 20)) printk(BIOS_DEBUG, "SMLINK_SLV ");
+ if (tco_sts & (1 << 18)) printk(BIOS_DEBUG, "BOOT ");
+ if (tco_sts & (1 << 17)) printk(BIOS_DEBUG, "SECOND_TO ");
+ if (tco_sts & (1 << 16)) printk(BIOS_DEBUG, "INTRD_DET ");
+ if (tco_sts & (1 << 12)) printk(BIOS_DEBUG, "DMISERR ");
+ if (tco_sts & (1 << 10)) printk(BIOS_DEBUG, "DMISMI ");
+ if (tco_sts & (1 << 9)) printk(BIOS_DEBUG, "DMISCI ");
+ if (tco_sts & (1 << 8)) printk(BIOS_DEBUG, "BIOSWR ");
+ if (tco_sts & (1 << 7)) printk(BIOS_DEBUG, "NEWCENTURY ");
+ if (tco_sts & (1 << 3)) printk(BIOS_DEBUG, "TIMEOUT ");
+ if (tco_sts & (1 << 2)) printk(BIOS_DEBUG, "TCO_INT ");
+ if (tco_sts & (1 << 1)) printk(BIOS_DEBUG, "SW_TCO ");
+ if (tco_sts & (1 << 0)) printk(BIOS_DEBUG, "NMI2SMI ");
+ printk(BIOS_DEBUG, "\n");
+}
+
+int southbridge_io_trap_handler(int smif)
+{
+ switch (smif) {
+ case 0x32:
+ printk(BIOS_DEBUG, "OS Init\n");
+ /* gnvs->smif:
+ * On success, the IO Trap Handler returns 0
+ * On failure, the IO Trap Handler returns a value != 0
+ */
+ gnvs->smif = 0;
+ return 1; /* IO trap handled */
+ }
+
+ /* Not handled */
+ return 0;
+}
+
+/**
+ * @brief Set the EOS bit
+ */
+void southbridge_smi_set_eos(void)
+{
+ u8 reg8;
+
+ reg8 = inb(pmbase + SMI_EN);
+ reg8 |= EOS;
+ outb(reg8, pmbase + SMI_EN);
+}
+
+static void busmaster_disable_on_bus(int bus)
+{
+ int slot, func;
+ unsigned int val;
+ unsigned char hdr;
+
+ for (slot = 0; slot < 0x20; slot++) {
+ for (func = 0; func < 8; func++) {
+ u32 reg32;
+ device_t dev = PCI_DEV(bus, slot, func);
+
+ val = pci_read_config32(dev, PCI_VENDOR_ID);
+
+ if (val == 0xffffffff || val == 0x00000000 ||
+ val == 0x0000ffff || val == 0xffff0000)
+ continue;
+
+ /* Disable Bus Mastering for this one device */
+ reg32 = pci_read_config32(dev, PCI_COMMAND);
+ reg32 &= ~PCI_COMMAND_MASTER;
+ pci_write_config32(dev, PCI_COMMAND, reg32);
+
+ /* If this is a bridge, then follow it. */
+ hdr = pci_read_config8(dev, PCI_HEADER_TYPE);
+ hdr &= 0x7f;
+ if (hdr == PCI_HEADER_TYPE_BRIDGE ||
+ hdr == PCI_HEADER_TYPE_CARDBUS) {
+ unsigned int buses;
+ buses = pci_read_config32(dev, PCI_PRIMARY_BUS);
+ busmaster_disable_on_bus((buses >> 8) & 0xff);
+ }
+ }
+ }
+}
+
+/*
+ * Drive GPIO 60 low to gate memory reset in S3.
+ *
+ * Intel reference designs all use GPIO 60 but it is
+ * not a requirement and boards could use a different pin.
+ */
+static void southbridge_gate_memory_reset(void)
+{
+ u32 reg32;
+ u16 gpiobase;
+
+ gpiobase = pcie_read_config16(PCI_DEV(0, 0x1f, 0), GPIOBASE) & 0xfffc;
+ if (!gpiobase)
+ return;
+
+ /* Make sure it is set as GPIO */
+ reg32 = inl(gpiobase + GPIO_USE_SEL2);
+ if (!(reg32 & (1 << 28))) {
+ reg32 |= (1 << 28);
+ outl(reg32, gpiobase + GPIO_USE_SEL2);
+ }
+
+ /* Make sure it is set as output */
+ reg32 = inl(gpiobase + GP_IO_SEL2);
+ if (reg32 & (1 << 28)) {
+ reg32 &= ~(1 << 28);
+ outl(reg32, gpiobase + GP_IO_SEL2);
+ }
+
+ /* Drive the output low */
+ reg32 = inl(gpiobase + GP_LVL2);
+ reg32 &= ~(1 << 28);
+ outl(reg32, gpiobase + GP_LVL2);
+}
+
+static void southbridge_smi_sleep(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u8 reg8;
+ u32 reg32;
+ u8 slp_typ;
+ u8 s5pwr = CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
+
+ // save and recover RTC port values
+ u8 tmp70, tmp72;
+ tmp70 = inb(0x70);
+ tmp72 = inb(0x72);
+ get_option(&s5pwr, "power_on_after_fail");
+ outb(tmp70, 0x70);
+ outb(tmp72, 0x72);
+
+ void (*mainboard_sleep)(u8 slp_typ) = mainboard_smi_sleep;
+
+ /* First, disable further SMIs */
+ reg8 = inb(pmbase + SMI_EN);
+ reg8 &= ~SLP_SMI_EN;
+ outb(reg8, pmbase + SMI_EN);
+
+ /* Figure out SLP_TYP */
+ reg32 = inl(pmbase + PM1_CNT);
+ printk(BIOS_SPEW, "SMI#: SLP = 0x%08x\n", reg32);
+ slp_typ = (reg32 >> 10) & 7;
+
+ /* Do any mainboard sleep handling */
+ tseg_relocate((void **)&mainboard_sleep);
+ if (mainboard_sleep)
+ mainboard_sleep(slp_typ-2);
+
+#if CONFIG_ELOG_GSMI
+ /* Log S3, S4, and S5 entry */
+ if (slp_typ >= 5)
+ elog_add_event_byte(ELOG_TYPE_ACPI_ENTER, slp_typ-2);
+#endif
+
+ /* Next, do the deed.
+ */
+
+ switch (slp_typ) {
+ case 0: printk(BIOS_DEBUG, "SMI#: Entering S0 (On)\n"); break;
+ case 1: printk(BIOS_DEBUG, "SMI#: Entering S1 (Assert STPCLK#)\n"); break;
+ case 5:
+ printk(BIOS_DEBUG, "SMI#: Entering S3 (Suspend-To-RAM)\n");
+
+ /* Gate memory reset */
+ southbridge_gate_memory_reset();
+
+ /* Invalidate the cache before going to S3 */
+ wbinvd();
+ break;
+ case 6: printk(BIOS_DEBUG, "SMI#: Entering S4 (Suspend-To-Disk)\n"); break;
+ case 7:
+ printk(BIOS_DEBUG, "SMI#: Entering S5 (Soft Power off)\n");
+
+ outl(0, pmbase + GPE0_EN);
+
+ /* Always set the flag in case CMOS was changed on runtime. For
+ * "KEEP", switch to "OFF" - KEEP is software emulated
+ */
+ reg8 = pcie_read_config8(PCI_DEV(0, 0x1f, 0), GEN_PMCON_3);
+ if (s5pwr == MAINBOARD_POWER_ON) {
+ reg8 &= ~1;
+ } else {
+ reg8 |= 1;
+ }
+ pcie_write_config8(PCI_DEV(0, 0x1f, 0), GEN_PMCON_3, reg8);
+
+ /* also iterates over all bridges on bus 0 */
+ busmaster_disable_on_bus(0);
+ break;
+ default: printk(BIOS_DEBUG, "SMI#: ERROR: SLP_TYP reserved\n"); break;
+ }
+
+ /* Write back to the SLP register to cause the originally intended
+ * event again. We need to set BIT13 (SLP_EN) though to make the
+ * sleep happen.
+ */
+ outl(reg32 | SLP_EN, pmbase + PM1_CNT);
+
+ /* Make sure to stop executing code here for S3/S4/S5 */
+ if (slp_typ > 1)
+ hlt();
+
+ /* In most sleep states, the code flow of this function ends at
+ * the line above. However, if we entered sleep state S1 and wake
+ * up again, we will continue to execute code in this function.
+ */
+ reg32 = inl(pmbase + PM1_CNT);
+ if (reg32 & SCI_EN) {
+ /* The OS is not an ACPI OS, so we set the state to S0 */
+ reg32 &= ~(SLP_EN | SLP_TYP);
+ outl(reg32, pmbase + PM1_CNT);
+ }
+}
+
+/*
+ * Look for Synchronous IO SMI and use save state from that
+ * core in case we are not running on the same core that
+ * initiated the IO transaction.
+ */
+/* FIXME: Confirm Haswell's SMM save state area structure. */
+static em64t101_smm_state_save_area_t *smi_apmc_find_state_save(u8 cmd)
+{
+ em64t101_smm_state_save_area_t *state;
+ u32 base = smi_get_tseg_base() + 0x8000 + 0x7d00;
+ int node;
+
+ /* Check all nodes looking for the one that issued the IO */
+ for (node = 0; node < CONFIG_MAX_CPUS; node++) {
+ state = (em64t101_smm_state_save_area_t *)
+ (base - (node * 0x400));
+
+ /* Check for Synchronous IO (bit0==1) */
+ if (!(state->io_misc_info & (1 << 0)))
+ continue;
+
+ /* Make sure it was a write (bit4==0) */
+ if (state->io_misc_info & (1 << 4))
+ continue;
+
+ /* Check for APMC IO port */
+ if (((state->io_misc_info >> 16) & 0xff) != APM_CNT)
+ continue;
+
+ /* Check AX against the requested command */
+ if ((state->rax & 0xff) != cmd)
+ continue;
+
+ return state;
+ }
+
+ return NULL;
+}
+
+#if CONFIG_ELOG_GSMI
+static void southbridge_smi_gsmi(void)
+{
+ u32 *ret, *param;
+ u8 sub_command;
+ em64t101_smm_state_save_area_t *io_smi =
+ smi_apmc_find_state_save(ELOG_GSMI_APM_CNT);
+
+ if (!io_smi)
+ return;
+
+ /* Command and return value in EAX */
+ ret = (u32*)&io_smi->rax;
+ sub_command = (u8)(*ret >> 8);
+
+ /* Parameter buffer in EBX */
+ param = (u32*)&io_smi->rbx;
+
+ /* drivers/elog/gsmi.c */
+ *ret = gsmi_exec(sub_command, param);
+}
+#endif
+
+static void southbridge_smi_apmc(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u32 pmctrl;
+ u8 reg8;
+ int (*mainboard_apmc)(u8 apmc) = mainboard_smi_apmc;
+ em64t101_smm_state_save_area_t *state;
+
+ /* Emulate B2 register as the FADT / Linux expects it */
+
+ reg8 = inb(APM_CNT);
+ switch (reg8) {
+ case APM_CNT_CST_CONTROL:
+ /* Calling this function seems to cause
+ * some kind of race condition in Linux
+ * and causes a kernel oops
+ */
+ printk(BIOS_DEBUG, "C-state control\n");
+ break;
+ case APM_CNT_PST_CONTROL:
+ /* Calling this function seems to cause
+ * some kind of race condition in Linux
+ * and causes a kernel oops
+ */
+ printk(BIOS_DEBUG, "P-state control\n");
+ break;
+ case APM_CNT_ACPI_DISABLE:
+ pmctrl = inl(pmbase + PM1_CNT);
+ pmctrl &= ~SCI_EN;
+ outl(pmctrl, pmbase + PM1_CNT);
+ printk(BIOS_DEBUG, "SMI#: ACPI disabled.\n");
+ break;
+ case APM_CNT_ACPI_ENABLE:
+ pmctrl = inl(pmbase + PM1_CNT);
+ pmctrl |= SCI_EN;
+ outl(pmctrl, pmbase + PM1_CNT);
+ printk(BIOS_DEBUG, "SMI#: ACPI enabled.\n");
+ break;
+ case APM_CNT_GNVS_UPDATE:
+ if (smm_initialized) {
+ printk(BIOS_DEBUG, "SMI#: SMM structures already initialized!\n");
+ return;
+ }
+ state = smi_apmc_find_state_save(reg8);
+ if (state) {
+ /* EBX in the state save contains the GNVS pointer */
+ gnvs = (global_nvs_t *)((u32)state->rbx);
+ smm_initialized = 1;
+ printk(BIOS_DEBUG, "SMI#: Setting GNVS to %p\n", gnvs);
+ }
+ break;
+#if CONFIG_ELOG_GSMI
+ case ELOG_GSMI_APM_CNT:
+ southbridge_smi_gsmi();
+ break;
+#endif
+ }
+
+ tseg_relocate((void **)&mainboard_apmc);
+ if (mainboard_apmc)
+ mainboard_apmc(reg8);
+}
+
+static void southbridge_smi_pm1(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u16 pm1_sts;
+
+ pm1_sts = reset_pm1_status();
+ dump_pm1_status(pm1_sts);
+
+ /* While OSPM is not active, poweroff immediately
+ * on a power button event.
+ */
+ if (pm1_sts & PWRBTN_STS) {
+ // power button pressed
+ u32 reg32;
+ reg32 = (7 << 10) | (1 << 13);
+#if CONFIG_ELOG_GSMI
+ elog_add_event(ELOG_TYPE_POWER_BUTTON);
+#endif
+ outl(reg32, pmbase + PM1_CNT);
+ }
+}
+
+static void southbridge_smi_gpe0(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u32 gpe0_sts;
+
+ gpe0_sts = reset_gpe0_status();
+ dump_gpe0_status(gpe0_sts);
+}
+
+static void southbridge_smi_gpi(unsigned int node, smm_state_save_area_t *state_save)
+{
+ void (*mainboard_gpi)(u16 gpi_sts) = mainboard_smi_gpi;
+ u16 reg16;
+ reg16 = inw(pmbase + ALT_GP_SMI_STS);
+ outw(reg16, pmbase + ALT_GP_SMI_STS);
+
+ reg16 &= inw(pmbase + ALT_GP_SMI_EN);
+
+ tseg_relocate((void **)&mainboard_gpi);
+ if (mainboard_gpi) {
+ mainboard_gpi(reg16);
+ } else {
+ if (reg16)
+ printk(BIOS_DEBUG, "GPI (mask %04x)\n",reg16);
+ }
+
+ outw(reg16, pmbase + ALT_GP_SMI_STS);
+}
+
+static void southbridge_smi_mc(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u32 reg32;
+
+ reg32 = inl(pmbase + SMI_EN);
+
+ /* Are periodic SMIs enabled? */
+ if ((reg32 & MCSMI_EN) == 0)
+ return;
+
+ printk(BIOS_DEBUG, "Microcontroller SMI.\n");
+}
+
+
+
+static void southbridge_smi_tco(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u32 tco_sts;
+
+ tco_sts = reset_tco_status();
+
+ /* Any TCO event? */
+ if (!tco_sts)
+ return;
+
+ if (tco_sts & (1 << 8)) { // BIOSWR
+ u8 bios_cntl;
+
+ bios_cntl = pcie_read_config16(PCI_DEV(0, 0x1f, 0), 0xdc);
+
+ if (bios_cntl & 1) {
+ /* BWE is RW, so the SMI was caused by a
+ * write to BWE, not by a write to the BIOS
+ */
+
+ /* This is the place where we notice someone
+ * is trying to tinker with the BIOS. We are
+ * trying to be nice and just ignore it. A more
+ * resolute answer would be to power down the
+ * box.
+ */
+ printk(BIOS_DEBUG, "Switching back to RO\n");
+ pcie_write_config32(PCI_DEV(0, 0x1f, 0), 0xdc, (bios_cntl & ~1));
+ } /* No else for now? */
+ } else if (tco_sts & (1 << 3)) { /* TIMEOUT */
+ /* Handle TCO timeout */
+ printk(BIOS_DEBUG, "TCO Timeout.\n");
+ } else if (!tco_sts) {
+ dump_tco_status(tco_sts);
+ }
+}
+
+static void southbridge_smi_periodic(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u32 reg32;
+
+ reg32 = inl(pmbase + SMI_EN);
+
+ /* Are periodic SMIs enabled? */
+ if ((reg32 & PERIODIC_EN) == 0)
+ return;
+
+ printk(BIOS_DEBUG, "Periodic SMI.\n");
+}
+
+static void southbridge_smi_monitor(unsigned int node, smm_state_save_area_t *state_save)
+{
+#define IOTRAP(x) (trap_sts & (1 << x))
+ u32 trap_sts, trap_cycle;
+ u32 data, mask = 0;
+ int i;
+
+ trap_sts = RCBA32(0x1e00); // TRSR - Trap Status Register
+ RCBA32(0x1e00) = trap_sts; // Clear trap(s) in TRSR
+
+ trap_cycle = RCBA32(0x1e10);
+ for (i=16; i<20; i++) {
+ if (trap_cycle & (1 << i))
+ mask |= (0xff << ((i - 16) << 2));
+ }
+
+
+ /* IOTRAP(3) SMI function call */
+ if (IOTRAP(3)) {
+ if (gnvs && gnvs->smif)
+ io_trap_handler(gnvs->smif); // call function smif
+ return;
+ }
+
+ /* IOTRAP(2) currently unused
+ * IOTRAP(1) currently unused */
+
+ /* IOTRAP(0) SMIC */
+ if (IOTRAP(0)) {
+ if (!(trap_cycle & (1 << 24))) { // It's a write
+ printk(BIOS_DEBUG, "SMI1 command\n");
+ data = RCBA32(0x1e18);
+ data &= mask;
+ // if (smi1)
+ // southbridge_smi_command(data);
+ // return;
+ }
+ // Fall through to debug
+ }
+
+ printk(BIOS_DEBUG, " trapped io address = 0x%x\n", trap_cycle & 0xfffc);
+ for (i=0; i < 4; i++) if(IOTRAP(i)) printk(BIOS_DEBUG, " TRAP = %d\n", i);
+ printk(BIOS_DEBUG, " AHBE = %x\n", (trap_cycle >> 16) & 0xf);
+ printk(BIOS_DEBUG, " MASK = 0x%08x\n", mask);
+ printk(BIOS_DEBUG, " read/write: %s\n", (trap_cycle & (1 << 24)) ? "read" : "write");
+
+ if (!(trap_cycle & (1 << 24))) {
+ /* Write Cycle */
+ data = RCBA32(0x1e18);
+ printk(BIOS_DEBUG, " iotrap written data = 0x%08x\n", data);
+ }
+#undef IOTRAP
+}
+
+typedef void (*smi_handler_t)(unsigned int node,
+ smm_state_save_area_t *state_save);
+
+static smi_handler_t southbridge_smi[32] = {
+ NULL, // [0] reserved
+ NULL, // [1] reserved
+ NULL, // [2] BIOS_STS
+ NULL, // [3] LEGACY_USB_STS
+ southbridge_smi_sleep, // [4] SLP_SMI_STS
+ southbridge_smi_apmc, // [5] APM_STS
+ NULL, // [6] SWSMI_TMR_STS
+ NULL, // [7] reserved
+ southbridge_smi_pm1, // [8] PM1_STS
+ southbridge_smi_gpe0, // [9] GPE0_STS
+ southbridge_smi_gpi, // [10] GPI_STS
+ southbridge_smi_mc, // [11] MCSMI_STS
+ NULL, // [12] DEVMON_STS
+ southbridge_smi_tco, // [13] TCO_STS
+ southbridge_smi_periodic, // [14] PERIODIC_STS
+ NULL, // [15] SERIRQ_SMI_STS
+ NULL, // [16] SMBUS_SMI_STS
+ NULL, // [17] LEGACY_USB2_STS
+ NULL, // [18] INTEL_USB2_STS
+ NULL, // [19] reserved
+ NULL, // [20] PCI_EXP_SMI_STS
+ southbridge_smi_monitor, // [21] MONITOR_STS
+ NULL, // [22] reserved
+ NULL, // [23] reserved
+ NULL, // [24] reserved
+ NULL, // [25] EL_SMI_STS
+ NULL, // [26] SPI_STS
+ NULL, // [27] reserved
+ NULL, // [28] reserved
+ NULL, // [29] reserved
+ NULL, // [30] reserved
+ NULL // [31] reserved
+};
+
+/**
+ * @brief Interrupt handler for SMI#
+ *
+ * @param smm_revision revision of the smm state save map
+ */
+
+void southbridge_smi_handler(unsigned int node, smm_state_save_area_t *state_save)
+{
+ int i, dump = 0;
+ u32 smi_sts;
+
+ /* Update global variable pmbase */
+ pmbase = pcie_read_config16(PCI_DEV(0, 0x1f, 0), 0x40) & 0xfffc;
+
+ /* We need to clear the SMI status registers, or we won't see what's
+ * happening in the following calls.
+ */
+ smi_sts = reset_smi_status();
+
+ /* Call SMI sub handler for each of the status bits */
+ for (i = 0; i < 31; i++) {
+ if (smi_sts & (1 << i)) {
+ if (southbridge_smi[i]) {
+#if CONFIG_SMM_TSEG
+ smi_handler_t handler = (smi_handler_t)
+ ((u8*)southbridge_smi[i] +
+ smi_get_tseg_base());
+ if (handler)
+ handler(node, state_save);
+#else
+ southbridge_smi[i](node, state_save);
+#endif
+ } else {
+ printk(BIOS_DEBUG, "SMI_STS[%d] occured, but no "
+ "handler available.\n", i);
+ dump = 1;
+ }
+ }
+ }
+
+ if(dump) {
+ dump_smi_status(smi_sts);
+ }
+
+}
diff --git a/src/southbridge/intel/lynxpoint/spi.c b/src/southbridge/intel/lynxpoint/spi.c
new file mode 100644
index 0000000..2050412
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/spi.c
@@ -0,0 +1,746 @@
+/*
+ * Copyright (c) 2011 The Chromium OS Authors.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but without any warranty; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* This file is derived from the flashrom project. */
+#include <stdint.h>
+#include <stdlib.h>
+#include <string.h>
+#include <delay.h>
+#include <arch/io.h>
+#include <console/console.h>
+#include <device/pci_ids.h>
+
+#include <spi-generic.h>
+
+#define min(a, b) ((a)<(b)?(a):(b))
+
+#ifdef __SMM__
+#include <arch/romcc_io.h>
+#include <northbridge/intel/haswell/pcie_config.c>
+#define pci_read_config_byte(dev, reg, targ)\
+ *(targ) = pcie_read_config8(dev, reg)
+#define pci_read_config_word(dev, reg, targ)\
+ *(targ) = pcie_read_config16(dev, reg)
+#define pci_read_config_dword(dev, reg, targ)\
+ *(targ) = pcie_read_config32(dev, reg)
+#define pci_write_config_byte(dev, reg, val)\
+ pcie_write_config8(dev, reg, val)
+#define pci_write_config_word(dev, reg, val)\
+ pcie_write_config16(dev, reg, val)
+#define pci_write_config_dword(dev, reg, val)\
+ pcie_write_config32(dev, reg, val)
+#else /* !__SMM__ */
+#include <device/device.h>
+#include <device/pci.h>
+#define pci_read_config_byte(dev, reg, targ)\
+ *(targ) = pci_read_config8(dev, reg)
+#define pci_read_config_word(dev, reg, targ)\
+ *(targ) = pci_read_config16(dev, reg)
+#define pci_read_config_dword(dev, reg, targ)\
+ *(targ) = pci_read_config32(dev, reg)
+#define pci_write_config_byte(dev, reg, val)\
+ pci_write_config8(dev, reg, val)
+#define pci_write_config_word(dev, reg, val)\
+ pci_write_config16(dev, reg, val)
+#define pci_write_config_dword(dev, reg, val)\
+ pci_write_config32(dev, reg, val)
+#endif /* !__SMM__ */
+
+typedef struct spi_slave ich_spi_slave;
+
+static int ichspi_lock = 0;
+
+typedef struct ich7_spi_regs {
+ uint16_t spis;
+ uint16_t spic;
+ uint32_t spia;
+ uint64_t spid[8];
+ uint64_t _pad;
+ uint32_t bbar;
+ uint16_t preop;
+ uint16_t optype;
+ uint8_t opmenu[8];
+} __attribute__((packed)) ich7_spi_regs;
+
+typedef struct ich9_spi_regs {
+ uint32_t bfpr;
+ uint16_t hsfs;
+ uint16_t hsfc;
+ uint32_t faddr;
+ uint32_t _reserved0;
+ uint32_t fdata[16];
+ uint32_t frap;
+ uint32_t freg[5];
+ uint32_t _reserved1[3];
+ uint32_t pr[5];
+ uint32_t _reserved2[2];
+ uint8_t ssfs;
+ uint8_t ssfc[3];
+ uint16_t preop;
+ uint16_t optype;
+ uint8_t opmenu[8];
+ uint32_t bbar;
+ uint8_t _reserved3[12];
+ uint32_t fdoc;
+ uint32_t fdod;
+ uint8_t _reserved4[8];
+ uint32_t afc;
+ uint32_t lvscc;
+ uint32_t uvscc;
+ uint8_t _reserved5[4];
+ uint32_t fpb;
+ uint8_t _reserved6[28];
+ uint32_t srdl;
+ uint32_t srdc;
+ uint32_t srd;
+} __attribute__((packed)) ich9_spi_regs;
+
+typedef struct ich_spi_controller {
+ int locked;
+
+ uint8_t *opmenu;
+ int menubytes;
+ uint16_t *preop;
+ uint16_t *optype;
+ uint32_t *addr;
+ uint8_t *data;
+ unsigned databytes;
+ uint8_t *status;
+ uint16_t *control;
+ uint32_t *bbar;
+} ich_spi_controller;
+
+static ich_spi_controller cntlr;
+
+enum {
+ SPIS_SCIP = 0x0001,
+ SPIS_GRANT = 0x0002,
+ SPIS_CDS = 0x0004,
+ SPIS_FCERR = 0x0008,
+ SSFS_AEL = 0x0010,
+ SPIS_LOCK = 0x8000,
+ SPIS_RESERVED_MASK = 0x7ff0,
+ SSFS_RESERVED_MASK = 0x7fe2
+};
+
+enum {
+ SPIC_SCGO = 0x000002,
+ SPIC_ACS = 0x000004,
+ SPIC_SPOP = 0x000008,
+ SPIC_DBC = 0x003f00,
+ SPIC_DS = 0x004000,
+ SPIC_SME = 0x008000,
+ SSFC_SCF_MASK = 0x070000,
+ SSFC_RESERVED = 0xf80000
+};
+
+enum {
+ HSFS_FDONE = 0x0001,
+ HSFS_FCERR = 0x0002,
+ HSFS_AEL = 0x0004,
+ HSFS_BERASE_MASK = 0x0018,
+ HSFS_BERASE_SHIFT = 3,
+ HSFS_SCIP = 0x0020,
+ HSFS_FDOPSS = 0x2000,
+ HSFS_FDV = 0x4000,
+ HSFS_FLOCKDN = 0x8000
+};
+
+enum {
+ HSFC_FGO = 0x0001,
+ HSFC_FCYCLE_MASK = 0x0006,
+ HSFC_FCYCLE_SHIFT = 1,
+ HSFC_FDBC_MASK = 0x3f00,
+ HSFC_FDBC_SHIFT = 8,
+ HSFC_FSMIE = 0x8000
+};
+
+enum {
+ SPI_OPCODE_TYPE_READ_NO_ADDRESS = 0,
+ SPI_OPCODE_TYPE_WRITE_NO_ADDRESS = 1,
+ SPI_OPCODE_TYPE_READ_WITH_ADDRESS = 2,
+ SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS = 3
+};
+
+#if CONFIG_DEBUG_SPI_FLASH
+
+static u8 readb_(const void *addr)
+{
+ u8 v = read8((unsigned long)addr);
+ printk(BIOS_DEBUG, "read %2.2x from %4.4x\n",
+ v, ((unsigned) addr & 0xffff) - 0xf020);
+ return v;
+}
+
+static u16 readw_(const void *addr)
+{
+ u16 v = read16((unsigned long)addr);
+ printk(BIOS_DEBUG, "read %4.4x from %4.4x\n",
+ v, ((unsigned) addr & 0xffff) - 0xf020);
+ return v;
+}
+
+static u32 readl_(const void *addr)
+{
+ u32 v = read32((unsigned long)addr);
+ printk(BIOS_DEBUG, "read %8.8x from %4.4x\n",
+ v, ((unsigned) addr & 0xffff) - 0xf020);
+ return v;
+}
+
+static void writeb_(u8 b, const void *addr)
+{
+ write8((unsigned long)addr, b);
+ printk(BIOS_DEBUG, "wrote %2.2x to %4.4x\n",
+ b, ((unsigned) addr & 0xffff) - 0xf020);
+}
+
+static void writew_(u16 b, const void *addr)
+{
+ write16((unsigned long)addr, b);
+ printk(BIOS_DEBUG, "wrote %4.4x to %4.4x\n",
+ b, ((unsigned) addr & 0xffff) - 0xf020);
+}
+
+static void writel_(u32 b, const void *addr)
+{
+ write32((unsigned long)addr, b);
+ printk(BIOS_DEBUG, "wrote %8.8x to %4.4x\n",
+ b, ((unsigned) addr & 0xffff) - 0xf020);
+}
+
+#else /* CONFIG_DEBUG_SPI_FLASH ^^^ enabled vvv NOT enabled */
+
+#define readb_(a) read8((uint32_t)a)
+#define readw_(a) read16((uint32_t)a)
+#define readl_(a) read32((uint32_t)a)
+#define writeb_(val, addr) write8((uint32_t)addr, val)
+#define writew_(val, addr) write16((uint32_t)addr, val)
+#define writel_(val, addr) write32((uint32_t)addr, val)
+
+#endif /* CONFIG_DEBUG_SPI_FLASH ^^^ NOT enabled */
+
+static void write_reg(const void *value, void *dest, uint32_t size)
+{
+ const uint8_t *bvalue = value;
+ uint8_t *bdest = dest;
+
+ while (size >= 4) {
+ writel_(*(const uint32_t *)bvalue, bdest);
+ bdest += 4; bvalue += 4; size -= 4;
+ }
+ while (size) {
+ writeb_(*bvalue, bdest);
+ bdest++; bvalue++; size--;
+ }
+}
+
+static void read_reg(const void *src, void *value, uint32_t size)
+{
+ const uint8_t *bsrc = src;
+ uint8_t *bvalue = value;
+
+ while (size >= 4) {
+ *(uint32_t *)bvalue = readl_(bsrc);
+ bsrc += 4; bvalue += 4; size -= 4;
+ }
+ while (size) {
+ *bvalue = readb_(bsrc);
+ bsrc++; bvalue++; size--;
+ }
+}
+
+static void ich_set_bbar(uint32_t minaddr)
+{
+ const uint32_t bbar_mask = 0x00ffff00;
+ uint32_t ichspi_bbar;
+
+ minaddr &= bbar_mask;
+ ichspi_bbar = readl_(cntlr.bbar) & ~bbar_mask;
+ ichspi_bbar |= minaddr;
+ writel_(ichspi_bbar, cntlr.bbar);
+}
+
+int spi_cs_is_valid(unsigned int bus, unsigned int cs)
+{
+ printk(BIOS_DEBUG, "spi_cs_is_valid used but not implemented\n");
+ return 0;
+}
+
+struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
+ unsigned int max_hz, unsigned int mode)
+{
+ ich_spi_slave *slave = malloc(sizeof(*slave));
+
+ if (!slave) {
+ printk(BIOS_DEBUG, "ICH SPI: Bad allocation\n");
+ return NULL;
+ }
+
+ memset(slave, 0, sizeof(*slave));
+
+ slave->bus = bus;
+ slave->cs = cs;
+ return slave;
+}
+
+/*
+ * Check if this device ID matches one of supported Intel PCH devices.
+ *
+ * Return the ICH version if there is a match, or zero otherwise.
+ */
+static inline int get_ich_version(uint16_t device_id)
+{
+ if (device_id == PCI_DEVICE_ID_INTEL_TGP_LPC)
+ return 7;
+
+ if ((device_id >= PCI_DEVICE_ID_INTEL_COUGARPOINT_LPC_MIN &&
+ device_id <= PCI_DEVICE_ID_INTEL_COUGARPOINT_LPC_MAX) ||
+ (device_id >= PCI_DEVICE_ID_INTEL_PANTHERPOINT_LPC_MIN &&
+ device_id <= PCI_DEVICE_ID_INTEL_PANTHERPOINT_LPC_MAX))
+ return 9;
+
+ return 0;
+}
+
+void spi_init(void)
+{
+ int ich_version = 0;
+
+ uint8_t *rcrb; /* Root Complex Register Block */
+ uint32_t rcba; /* Root Complex Base Address */
+ uint8_t bios_cntl;
+ device_t dev;
+ uint32_t ids;
+ uint16_t vendor_id, device_id;
+
+#ifdef __SMM__
+ dev = PCI_DEV(0, 31, 0);
+#else
+ dev = dev_find_slot(0, PCI_DEVFN(31, 0));
+#endif
+ pci_read_config_dword(dev, 0, &ids);
+ vendor_id = ids;
+ device_id = (ids >> 16);
+
+ if (vendor_id != PCI_VENDOR_ID_INTEL) {
+ printk(BIOS_DEBUG, "ICH SPI: No ICH found.\n");
+ return;
+ }
+
+ ich_version = get_ich_version(device_id);
+
+ if (!ich_version) {
+ printk(BIOS_DEBUG, "ICH SPI: No known ICH found.\n");
+ return;
+ }
+
+ pci_read_config_dword(dev, 0xf0, &rcba);
+ /* Bits 31-14 are the base address, 13-1 are reserved, 0 is enable. */
+ rcrb = (uint8_t *)(rcba & 0xffffc000);
+ switch (ich_version) {
+ case 7:
+ {
+ const uint16_t ich7_spibar_offset = 0x3020;
+ ich7_spi_regs *ich7_spi =
+ (ich7_spi_regs *)(rcrb + ich7_spibar_offset);
+
+ ichspi_lock = readw_(&ich7_spi->spis) & SPIS_LOCK;
+ cntlr.opmenu = ich7_spi->opmenu;
+ cntlr.menubytes = sizeof(ich7_spi->opmenu);
+ cntlr.optype = &ich7_spi->optype;
+ cntlr.addr = &ich7_spi->spia;
+ cntlr.data = (uint8_t *)ich7_spi->spid;
+ cntlr.databytes = sizeof(ich7_spi->spid);
+ cntlr.status = (uint8_t *)&ich7_spi->spis;
+ cntlr.control = &ich7_spi->spic;
+ cntlr.bbar = &ich7_spi->bbar;
+ cntlr.preop = &ich7_spi->preop;
+ break;
+ }
+ case 9:
+ {
+ const uint16_t ich9_spibar_offset = 0x3800;
+ ich9_spi_regs *ich9_spi =
+ (ich9_spi_regs *)(rcrb + ich9_spibar_offset);
+ ichspi_lock = readw_(&ich9_spi->hsfs) & HSFS_FLOCKDN;
+ cntlr.opmenu = ich9_spi->opmenu;
+ cntlr.menubytes = sizeof(ich9_spi->opmenu);
+ cntlr.optype = &ich9_spi->optype;
+ cntlr.addr = &ich9_spi->faddr;
+ cntlr.data = (uint8_t *)ich9_spi->fdata;
+ cntlr.databytes = sizeof(ich9_spi->fdata);
+ cntlr.status = &ich9_spi->ssfs;
+ cntlr.control = (uint16_t *)ich9_spi->ssfc;
+ cntlr.bbar = &ich9_spi->bbar;
+ cntlr.preop = &ich9_spi->preop;
+ break;
+ }
+ default:
+ printk(BIOS_DEBUG, "ICH SPI: Unrecognized ICH version %d.\n", ich_version);
+ }
+
+ ich_set_bbar(0);
+
+ /* Disable the BIOS write protect so write commands are allowed. */
+ pci_read_config_byte(dev, 0xdc, &bios_cntl);
+ switch (ich_version) {
+ case 9:
+ /* Deassert SMM BIOS Write Protect Disable. */
+ bios_cntl &= ~(1 << 5);
+ break;
+
+ default:
+ break;
+ }
+ pci_write_config_byte(dev, 0xdc, bios_cntl | 0x1);
+}
+
+int spi_claim_bus(struct spi_slave *slave)
+{
+ /* Handled by ICH automatically. */
+ return 0;
+}
+
+void spi_release_bus(struct spi_slave *slave)
+{
+ /* Handled by ICH automatically. */
+}
+
+void spi_cs_activate(struct spi_slave *slave)
+{
+ /* Handled by ICH automatically. */
+}
+
+void spi_cs_deactivate(struct spi_slave *slave)
+{
+ /* Handled by ICH automatically. */
+}
+
+typedef struct spi_transaction {
+ const uint8_t *out;
+ uint32_t bytesout;
+ uint8_t *in;
+ uint32_t bytesin;
+ uint8_t type;
+ uint8_t opcode;
+ uint32_t offset;
+} spi_transaction;
+
+static inline void spi_use_out(spi_transaction *trans, unsigned bytes)
+{
+ trans->out += bytes;
+ trans->bytesout -= bytes;
+}
+
+static inline void spi_use_in(spi_transaction *trans, unsigned bytes)
+{
+ trans->in += bytes;
+ trans->bytesin -= bytes;
+}
+
+static void spi_setup_type(spi_transaction *trans)
+{
+ trans->type = 0xFF;
+
+ /* Try to guess spi type from read/write sizes. */
+ if (trans->bytesin == 0) {
+ if (trans->bytesout > 4)
+ /*
+ * If bytesin = 0 and bytesout > 4, we presume this is
+ * a write data operation, which is accompanied by an
+ * address.
+ */
+ trans->type = SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS;
+ else
+ trans->type = SPI_OPCODE_TYPE_WRITE_NO_ADDRESS;
+ return;
+ }
+
+ if (trans->bytesout == 1) { /* and bytesin is > 0 */
+ trans->type = SPI_OPCODE_TYPE_READ_NO_ADDRESS;
+ return;
+ }
+
+ if (trans->bytesout == 4) { /* and bytesin is > 0 */
+ trans->type = SPI_OPCODE_TYPE_READ_WITH_ADDRESS;
+ }
+
+ /* Fast read command is called with 5 bytes instead of 4 */
+ if (trans->out[0] == SPI_OPCODE_FAST_READ && trans->bytesout == 5) {
+ trans->type = SPI_OPCODE_TYPE_READ_WITH_ADDRESS;
+ --trans->bytesout;
+ }
+}
+
+static int spi_setup_opcode(spi_transaction *trans)
+{
+ uint16_t optypes;
+ uint8_t opmenu[cntlr.menubytes];
+
+ trans->opcode = trans->out[0];
+ spi_use_out(trans, 1);
+ if (!ichspi_lock) {
+ /* The lock is off, so just use index 0. */
+ writeb_(trans->opcode, cntlr.opmenu);
+ optypes = readw_(cntlr.optype);
+ optypes = (optypes & 0xfffc) | (trans->type & 0x3);
+ writew_(optypes, cntlr.optype);
+ return 0;
+ } else {
+ /* The lock is on. See if what we need is on the menu. */
+ uint8_t optype;
+ uint16_t opcode_index;
+
+ /* Write Enable is handled as atomic prefix */
+ if (trans->opcode == SPI_OPCODE_WREN)
+ return 0;
+
+ read_reg(cntlr.opmenu, opmenu, sizeof(opmenu));
+ for (opcode_index = 0; opcode_index < cntlr.menubytes;
+ opcode_index++) {
+ if (opmenu[opcode_index] == trans->opcode)
+ break;
+ }
+
+ if (opcode_index == cntlr.menubytes) {
+ printk(BIOS_DEBUG, "ICH SPI: Opcode %x not found\n",
+ trans->opcode);
+ return -1;
+ }
+
+ optypes = readw_(cntlr.optype);
+ optype = (optypes >> (opcode_index * 2)) & 0x3;
+ if (trans->type == SPI_OPCODE_TYPE_WRITE_NO_ADDRESS &&
+ optype == SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS &&
+ trans->bytesout >= 3) {
+ /* We guessed wrong earlier. Fix it up. */
+ trans->type = optype;
+ }
+ if (optype != trans->type) {
+ printk(BIOS_DEBUG, "ICH SPI: Transaction doesn't fit type %d\n",
+ optype);
+ return -1;
+ }
+ return opcode_index;
+ }
+}
+
+static int spi_setup_offset(spi_transaction *trans)
+{
+ /* Separate the SPI address and data. */
+ switch (trans->type) {
+ case SPI_OPCODE_TYPE_READ_NO_ADDRESS:
+ case SPI_OPCODE_TYPE_WRITE_NO_ADDRESS:
+ return 0;
+ case SPI_OPCODE_TYPE_READ_WITH_ADDRESS:
+ case SPI_OPCODE_TYPE_WRITE_WITH_ADDRESS:
+ trans->offset = ((uint32_t)trans->out[0] << 16) |
+ ((uint32_t)trans->out[1] << 8) |
+ ((uint32_t)trans->out[2] << 0);
+ spi_use_out(trans, 3);
+ return 1;
+ default:
+ printk(BIOS_DEBUG, "Unrecognized SPI transaction type %#x\n", trans->type);
+ return -1;
+ }
+}
+
+/*
+ * Wait for up to 60ms til status register bit(s) turn 1 (in case wait_til_set
+ * below is True) or 0. In case the wait was for the bit(s) to set - write
+ * those bits back, which would cause resetting them.
+ *
+ * Return the last read status value on success or -1 on failure.
+ */
+static int ich_status_poll(u16 bitmask, int wait_til_set)
+{
+ int timeout = 6000; /* This will result in 60 ms */
+ u16 status = 0;
+
+ while (timeout--) {
+ status = readw_(cntlr.status);
+ if (wait_til_set ^ ((status & bitmask) == 0)) {
+ if (wait_til_set)
+ writew_((status & bitmask), cntlr.status);
+ return status;
+ }
+ udelay(10);
+ }
+
+ printk(BIOS_DEBUG, "ICH SPI: SCIP timeout, read %x, expected %x\n",
+ status, bitmask);
+ return -1;
+}
+
+int spi_xfer(struct spi_slave *slave, const void *dout,
+ unsigned int bitsout, void *din, unsigned int bitsin)
+{
+ uint16_t control;
+ int16_t opcode_index;
+ int with_address;
+ int status;
+
+ spi_transaction trans = {
+ dout, bitsout / 8,
+ din, bitsin / 8,
+ 0xff, 0xff, 0
+ };
+
+ /* There has to always at least be an opcode. */
+ if (!bitsout || !dout) {
+ printk(BIOS_DEBUG, "ICH SPI: No opcode for transfer\n");
+ return -1;
+ }
+ /* Make sure if we read something we have a place to put it. */
+ if (bitsin != 0 && !din) {
+ printk(BIOS_DEBUG, "ICH SPI: Read but no target buffer\n");
+ return -1;
+ }
+ /* Right now we don't support writing partial bytes. */
+ if (bitsout % 8 || bitsin % 8) {
+ printk(BIOS_DEBUG, "ICH SPI: Accessing partial bytes not supported\n");
+ return -1;
+ }
+
+ if (ich_status_poll(SPIS_SCIP, 0) == -1)
+ return -1;
+
+ writew_(SPIS_CDS | SPIS_FCERR, cntlr.status);
+
+ spi_setup_type(&trans);
+ if ((opcode_index = spi_setup_opcode(&trans)) < 0)
+ return -1;
+ if ((with_address = spi_setup_offset(&trans)) < 0)
+ return -1;
+
+ if (trans.opcode == SPI_OPCODE_WREN) {
+ /*
+ * Treat Write Enable as Atomic Pre-Op if possible
+ * in order to prevent the Management Engine from
+ * issuing a transaction between WREN and DATA.
+ */
+ if (!ichspi_lock)
+ writew_(trans.opcode, cntlr.preop);
+ return 0;
+ }
+
+ /* Preset control fields */
+ control = SPIC_SCGO | ((opcode_index & 0x07) << 4);
+
+ /* Issue atomic preop cycle if needed */
+ if (readw_(cntlr.preop))
+ control |= SPIC_ACS;
+
+ if (!trans.bytesout && !trans.bytesin) {
+ /* SPI addresses are 24 bit only */
+ if (with_address)
+ writel_(trans.offset & 0x00FFFFFF, cntlr.addr);
+
+ /*
+ * This is a 'no data' command (like Write Enable), its
+ * bitesout size was 1, decremented to zero while executing
+ * spi_setup_opcode() above. Tell the chip to send the
+ * command.
+ */
+ writew_(control, cntlr.control);
+
+ /* wait for the result */
+ status = ich_status_poll(SPIS_CDS | SPIS_FCERR, 1);
+ if (status == -1)
+ return -1;
+
+ if (status & SPIS_FCERR) {
+ printk(BIOS_DEBUG, "ICH SPI: Command transaction error\n");
+ return -1;
+ }
+
+ return 0;
+ }
+
+ /*
+ * Check if this is a write command atempting to transfer more bytes
+ * than the controller can handle. Iterations for writes are not
+ * supported here because each SPI write command needs to be preceded
+ * and followed by other SPI commands, and this sequence is controlled
+ * by the SPI chip driver.
+ */
+ if (trans.bytesout > cntlr.databytes) {
+ printk(BIOS_DEBUG, "ICH SPI: Too much to write. Does your SPI chip driver use"
+ " CONTROLLER_PAGE_LIMIT?\n");
+ return -1;
+ }
+
+ /*
+ * Read or write up to databytes bytes at a time until everything has
+ * been sent.
+ */
+ while (trans.bytesout || trans.bytesin) {
+ uint32_t data_length;
+
+ /* SPI addresses are 24 bit only */
+ writel_(trans.offset & 0x00FFFFFF, cntlr.addr);
+
+ if (trans.bytesout)
+ data_length = min(trans.bytesout, cntlr.databytes);
+ else
+ data_length = min(trans.bytesin, cntlr.databytes);
+
+ /* Program data into FDATA0 to N */
+ if (trans.bytesout) {
+ write_reg(trans.out, cntlr.data, data_length);
+ spi_use_out(&trans, data_length);
+ if (with_address)
+ trans.offset += data_length;
+ }
+
+ /* Add proper control fields' values */
+ control &= ~((cntlr.databytes - 1) << 8);
+ control |= SPIC_DS;
+ control |= (data_length - 1) << 8;
+
+ /* write it */
+ writew_(control, cntlr.control);
+
+ /* Wait for Cycle Done Status or Flash Cycle Error. */
+ status = ich_status_poll(SPIS_CDS | SPIS_FCERR, 1);
+ if (status == -1)
+ return -1;
+
+ if (status & SPIS_FCERR) {
+ printk(BIOS_DEBUG, "ICH SPI: Data transaction error\n");
+ return -1;
+ }
+
+ if (trans.bytesin) {
+ read_reg(cntlr.data, trans.in, data_length);
+ spi_use_in(&trans, data_length);
+ if (with_address)
+ trans.offset += data_length;
+ }
+ }
+
+ /* Clear atomic preop now that xfer is done */
+ writew_(0, cntlr.preop);
+
+ return 0;
+}
diff --git a/src/southbridge/intel/lynxpoint/usb_debug.c b/src/southbridge/intel/lynxpoint/usb_debug.c
new file mode 100644
index 0000000..1cee353
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/usb_debug.c
@@ -0,0 +1,51 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <stdint.h>
+#include <arch/io.h>
+#include <arch/romcc_io.h>
+#include <console/console.h>
+#include <usbdebug.h>
+#include <device/pci_def.h>
+#include "pch.h"
+
+/* Required for successful build, but currently empty. */
+void set_debug_port(unsigned int port)
+{
+ /* Not needed, the ICH* southbridges hardcode physical USB port 1. */
+}
+
+void enable_usbdebug(unsigned int port)
+{
+ u32 dbgctl;
+ device_t dev = PCI_DEV(0, 0x1d, 7); /* USB EHCI, D29:F7 */
+
+ /* Set the EHCI BAR address. */
+ pci_write_config32(dev, EHCI_BAR_INDEX, CONFIG_EHCI_BAR);
+
+ /* Enable access to the EHCI memory space registers. */
+ pci_write_config8(dev, PCI_COMMAND, PCI_COMMAND_MEMORY);
+
+ /* Force ownership of the Debug Port to the EHCI controller. */
+ printk(BIOS_DEBUG, "Enabling OWNER_CNT\n");
+ dbgctl = read32(CONFIG_EHCI_BAR + CONFIG_EHCI_DEBUG_OFFSET);
+ dbgctl |= (1 << 30);
+ write32(CONFIG_EHCI_BAR + CONFIG_EHCI_DEBUG_OFFSET, dbgctl);
+}
+
diff --git a/src/southbridge/intel/lynxpoint/usb_ehci.c b/src/southbridge/intel/lynxpoint/usb_ehci.c
new file mode 100644
index 0000000..aec230c
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/usb_ehci.c
@@ -0,0 +1,112 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <device/pci_ids.h>
+#include "pch.h"
+#include <usbdebug.h>
+#include <arch/io.h>
+
+static void usb_ehci_init(struct device *dev)
+{
+ u32 reg32;
+
+ /* Disable Wake on Disconnect in RMH */
+ reg32 = RCBA32(0x35b0);
+ reg32 |= 0x22;
+ RCBA32(0x35b0) = reg32;
+
+ printk(BIOS_DEBUG, "EHCI: Setting up controller.. ");
+ reg32 = pci_read_config32(dev, PCI_COMMAND);
+ reg32 |= PCI_COMMAND_MASTER;
+ //reg32 |= PCI_COMMAND_SERR;
+ pci_write_config32(dev, PCI_COMMAND, reg32);
+
+ printk(BIOS_DEBUG, "done.\n");
+}
+
+static void usb_ehci_set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ u8 access_cntl;
+
+ access_cntl = pci_read_config8(dev, 0x80);
+
+ /* Enable writes to protected registers. */
+ pci_write_config8(dev, 0x80, access_cntl | 1);
+
+ if (!vendor || !device) {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ pci_read_config32(dev, PCI_VENDOR_ID));
+ } else {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+ }
+
+ /* Restore protection. */
+ pci_write_config8(dev, 0x80, access_cntl);
+}
+
+static void usb_ehci_set_resources(struct device *dev)
+{
+#if CONFIG_USBDEBUG
+ struct resource *res;
+ u32 base;
+ u32 usb_debug;
+
+ usb_debug = get_ehci_debug();
+ set_ehci_debug(0);
+#endif
+ pci_dev_set_resources(dev);
+
+#if CONFIG_USBDEBUG
+ res = find_resource(dev, 0x10);
+ set_ehci_debug(usb_debug);
+ if (!res) return;
+ base = res->base;
+ set_ehci_base(base);
+ report_resource_stored(dev, res, "");
+#endif
+}
+
+
+
+static struct pci_operations lops_pci = {
+ .set_subsystem = &usb_ehci_set_subsystem,
+};
+
+static struct device_operations usb_ehci_ops = {
+ .read_resources = pci_dev_read_resources,
+ .set_resources = usb_ehci_set_resources,
+ .enable_resources = pci_dev_enable_resources,
+ .init = usb_ehci_init,
+ .scan_bus = 0,
+ .ops_pci = &lops_pci,
+};
+
+static const unsigned short pci_device_ids[] = { 0x1c26, 0x1c2d, 0x1e26, 0x1e2d,
+ 0 };
+
+static const struct pci_driver pch_usb_ehci __pci_driver = {
+ .ops = &usb_ehci_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .devices = pci_device_ids,
+};
diff --git a/src/southbridge/intel/lynxpoint/watchdog.c b/src/southbridge/intel/lynxpoint/watchdog.c
new file mode 100644
index 0000000..b6d9223
--- /dev/null
+++ b/src/southbridge/intel/lynxpoint/watchdog.c
@@ -0,0 +1,59 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2008-2009 coresystems GmbH
+ * Copyright (C) 2011 Google Inc.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#include <console/console.h>
+#include <arch/io.h>
+#include <device/device.h>
+#include <device/pci.h>
+#include <watchdog.h>
+
+ //
+ // Disable PCH Watchdog timer at SB_RCBA+0x3410
+ //
+ // Mmio32((MmPci32(0, 0, 0x1F, 0, 0xF0) & ~BIT0), 0x3410) |= 0x20;
+ //
+void watchdog_off(void)
+{
+ device_t dev;
+ unsigned long value, base;
+
+ /* Turn off the ICH7 watchdog. */
+ dev = dev_find_slot(0, PCI_DEVFN(0x1f, 0));
+
+ /* Enable I/O space. */
+ value = pci_read_config16(dev, 0x04);
+ value |= (1 << 10);
+ pci_write_config16(dev, 0x04, value);
+
+ /* Get TCO base. */
+ base = (pci_read_config32(dev, 0x40) & 0x0fffe) + 0x60;
+
+ /* Disable the watchdog timer. */
+ value = inw(base + 0x08);
+ value |= 1 << 11;
+ outw(value, base + 0x08);
+
+ /* Clear TCO timeout status. */
+ outw(0x0008, base + 0x04);
+ outw(0x0002, base + 0x06);
+
+ printk(BIOS_DEBUG, "PCH watchdog disabled\n");
+}