| chip soc/intel/skylake |
| |
| register "panel_cfg" = "{ |
| .up_delay_ms = 200, |
| .down_delay_ms = 50, |
| .cycle_delay_ms = 500, |
| .backlight_on_delay_ms = 1, |
| .backlight_off_delay_ms = 200, |
| .backlight_pwm_hz = 200, |
| }" |
| |
| # Deep Sx states |
| register "deep_s3_enable_ac" = "0" |
| register "deep_s3_enable_dc" = "0" |
| register "deep_s5_enable_ac" = "1" |
| register "deep_s5_enable_dc" = "1" |
| register "deep_sx_config" = "DSX_EN_LAN_WAKE_PIN | DSX_EN_WAKE_PIN" |
| |
| register "eist_enable" = "1" |
| |
| # Mapping of USB port # to device |
| #+----------------+-------+-----------------------------------+ |
| #| Device | Port# | Rev | |
| #+----------------+-------+-----------------------------------+ |
| #| USB C | 1 | 2/3 | |
| #| USB A Rear | 2 | 2/3 | |
| #| USB A Front | 3 | 2/3 | |
| #| USB A Front | 4 | 2/3 | |
| #| USB A Rear | 5 | 2 on base celeron, 2/3 all others | |
| #| USB A Rear | 6 | 2 on base celeron, 2/3 all others | |
| #| Bluetooth | 7 | | |
| #| Daughter Board | 8 | | |
| #+----------------+-------+-----------------------------------+ |
| |
| # Bitmap for Wake Enable on USB attach/detach |
| register "usb2_wake_enable_bitmap" = "USB_PORT_WAKE_ENABLE(2) | \ |
| USB_PORT_WAKE_ENABLE(3) | \ |
| USB_PORT_WAKE_ENABLE(4) | \ |
| USB_PORT_WAKE_ENABLE(5) | \ |
| USB_PORT_WAKE_ENABLE(6)" |
| register "usb3_wake_enable_bitmap" = "USB_PORT_WAKE_ENABLE(2) | \ |
| USB_PORT_WAKE_ENABLE(3) | \ |
| USB_PORT_WAKE_ENABLE(4) | \ |
| USB_PORT_WAKE_ENABLE(5) | \ |
| USB_PORT_WAKE_ENABLE(6)" |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route. i.e. If this route changes then the affected GPE |
| # offset bits also need to be changed. |
| register "gpe0_dw0" = "GPP_B" |
| register "gpe0_dw1" = "GPP_D" |
| register "gpe0_dw2" = "GPP_E" |
| |
| # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f |
| register "gen1_dec" = "0x00fc0801" |
| register "gen2_dec" = "0x000c0201" |
| # EC memory map range is 0x900-0x9ff |
| register "gen3_dec" = "0x00fc0901" |
| |
| # Enable DPTF |
| register "dptf_enable" = "1" |
| |
| # Enable S0ix |
| register "s0ix_enable" = true |
| |
| # FSP Configuration |
| register "SataSalpSupport" = "0" |
| register "SataPortsEnable[0]" = "1" |
| register "SataPortsEnable[1]" = "1" |
| register "SataPortsDevSlp[1]" = "1" |
| register "DspEnable" = "1" |
| register "IoBufferOwnership" = "3" |
| register "SsicPortEnable" = "0" |
| register "ScsEmmcHs400Enabled" = "0" |
| register "SkipExtGfxScan" = "1" |
| register "SaGv" = "SaGv_Enabled" |
| register "PmConfigSlpS3MinAssert" = "2" # 50ms |
| register "PmConfigSlpS4MinAssert" = "1" # 1s |
| register "PmConfigSlpSusMinAssert" = "1" # 500ms |
| register "PmConfigSlpAMinAssert" = "3" # 2s |
| register "SendVrMbxCmd" = "1" # IMVP8 workaround |
| |
| # Intersil VR c-state issue workaround |
| # send VR mailbox command for IA/GT/SA rails |
| register "IslVrCmd" = "2" |
| |
| # VR Settings Configuration for 4 Domains |
| #+----------------+-------+-------+-------+-------+ |
| #| Domain/Setting | SA | IA | GTUS | GTS | |
| #+----------------+-------+-------+-------+-------+ |
| #| Psi1Threshold | 20A | 20A | 20A | 20A | |
| #| Psi2Threshold | 4A | 5A | 5A | 5A | |
| #| Psi3Threshold | 1A | 1A | 1A | 1A | |
| #| Psi3Enable | 1 | 1 | 1 | 1 | |
| #| Psi4Enable | 1 | 1 | 1 | 1 | |
| #| ImonSlope | 0 | 0 | 0 | 0 | |
| #| ImonOffset | 0 | 0 | 0 | 0 | |
| #| IccMax | 7A | 34A | 35A | 35A | |
| #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | |
| #| AcLoadline(ohm)| 10.3m | 2.4m | 3.1m | 3.1m | |
| #| DcLoadline(ohm)| 10.3m | 2.4m | 3.1m | 3.1m | |
| #+----------------+-------+-------+-------+-------+ |
| #Note: IccMax settings are moved to SoC code |
| register "domain_vr_config[VR_SYSTEM_AGENT]" = "{ |
| .vr_config_enable = 1, |
| .psi1threshold = VR_CFG_AMP(20), |
| .psi2threshold = VR_CFG_AMP(4), |
| .psi3threshold = VR_CFG_AMP(1), |
| .psi3enable = 1, |
| .psi4enable = 1, |
| .imon_slope = 0x0, |
| .imon_offset = 0x0, |
| .voltage_limit = 1520, |
| .ac_loadline = 1030, |
| .dc_loadline = 1030, |
| }" |
| |
| register "domain_vr_config[VR_IA_CORE]" = "{ |
| .vr_config_enable = 1, |
| .psi1threshold = VR_CFG_AMP(20), |
| .psi2threshold = VR_CFG_AMP(5), |
| .psi3threshold = VR_CFG_AMP(1), |
| .psi3enable = 1, |
| .psi4enable = 1, |
| .imon_slope = 0x0, |
| .imon_offset = 0x0, |
| .voltage_limit = 1520, |
| .ac_loadline = 240, |
| .dc_loadline = 240, |
| }" |
| |
| register "domain_vr_config[VR_GT_UNSLICED]" = "{ |
| .vr_config_enable = 1, |
| .psi1threshold = VR_CFG_AMP(20), |
| .psi2threshold = VR_CFG_AMP(5), |
| .psi3threshold = VR_CFG_AMP(1), |
| .psi3enable = 1, |
| .psi4enable = 1, |
| .imon_slope = 0x0, |
| .imon_offset = 0x0, |
| .voltage_limit = 1520, |
| .ac_loadline = 310, |
| .dc_loadline = 310, |
| }" |
| |
| register "domain_vr_config[VR_GT_SLICED]" = "{ |
| .vr_config_enable = 1, |
| .psi1threshold = VR_CFG_AMP(20), |
| .psi2threshold = VR_CFG_AMP(5), |
| .psi3threshold = VR_CFG_AMP(1), |
| .psi3enable = 1, |
| .psi4enable = 1, |
| .imon_slope = 0x0, |
| .imon_offset = 0x0, |
| .voltage_limit = 1520, |
| .ac_loadline = 310, |
| .dc_loadline = 310, |
| }" |
| |
| # Enable Root port 3(x1) for LAN. |
| register "PcieRpEnable[2]" = "1" |
| # Enable CLKREQ# |
| register "PcieRpClkReqSupport[2]" = "1" |
| # RP 3 uses SRCCLKREQ0# |
| register "PcieRpClkReqNumber[2]" = "0" |
| # RP 3, Enable Advanced Error Reporting |
| register "PcieRpAdvancedErrorReporting[2]" = "1" |
| # RP 3, Enable Latency Tolerance Reporting Mechanism |
| register "PcieRpLtrEnable[2]" = "1" |
| # RP 3 uses CLK SRC 0 |
| register "PcieRpClkSrcNumber[2]" = "0" |
| |
| # Enable Root port 4(x1) for WLAN. |
| register "PcieRpEnable[3]" = "1" |
| # Enable CLKREQ# |
| register "PcieRpClkReqSupport[3]" = "1" |
| # RP 4 uses SRCCLKREQ5# |
| register "PcieRpClkReqNumber[3]" = "5" |
| # RP 4, Enable Advanced Error Reporting |
| register "PcieRpAdvancedErrorReporting[3]" = "1" |
| # RP 4, Enable Latency Tolerance Reporting Mechanism |
| register "PcieRpLtrEnable[3]" = "1" |
| # RP 4 uses CLK SRC 5 |
| register "PcieRpClkSrcNumber[3]" = "5" |
| |
| # Enable Root port 5(x4) for NVMe. |
| register "PcieRpEnable[4]" = "1" |
| # Enable CLKREQ# |
| register "PcieRpClkReqSupport[4]" = "1" |
| # RP 5 uses SRCCLKREQ1# |
| register "PcieRpClkReqNumber[4]" = "1" |
| # RP 5, Enable Advanced Error Reporting |
| register "PcieRpAdvancedErrorReporting[4]" = "1" |
| # RP 5, Enable Latency Tolerance Reporting Mechanism |
| register "PcieRpLtrEnable[4]" = "1" |
| # RP 5 uses CLK SRC 1 |
| register "PcieRpClkSrcNumber[4]" = "1" |
| |
| # Enable Root port 9 for BtoB. |
| register "PcieRpEnable[8]" = "1" |
| # Enable CLKREQ# |
| register "PcieRpClkReqSupport[8]" = "1" |
| # RP 9 uses SRCCLKREQ2# |
| register "PcieRpClkReqNumber[8]" = "2" |
| # RP 9, Enable Advanced Error Reporting |
| register "PcieRpAdvancedErrorReporting[8]" = "1" |
| # RP 9, Enable Latency Tolerance Reporting Mechanism |
| register "PcieRpLtrEnable[8]" = "1" |
| # RP 9 uses CLK SRC 2 |
| register "PcieRpClkSrcNumber[8]" = "2" |
| |
| # Enable Root port 11 for BtoB. |
| register "PcieRpEnable[10]" = "1" |
| # Enable CLKREQ# |
| register "PcieRpClkReqSupport[10]" = "1" |
| # RP 11 uses SRCCLKREQ2# |
| register "PcieRpClkReqNumber[10]" = "2" |
| # RP 11, Enable Advanced Error Reporting |
| register "PcieRpAdvancedErrorReporting[10]" = "1" |
| # RP 11, Enable Latency Tolerance Reporting Mechanism |
| register "PcieRpLtrEnable[10]" = "1" |
| # RP 11 uses CLK SRC 2 |
| register "PcieRpClkSrcNumber[10]" = "2" |
| |
| # Enable Root port 12 for BtoB. |
| register "PcieRpEnable[11]" = "1" |
| # Enable CLKREQ# |
| register "PcieRpClkReqSupport[11]" = "1" |
| # RP 12 uses SRCCLKREQ2# |
| register "PcieRpClkReqNumber[11]" = "2" |
| # RP 12, Enable Advanced Error Reporting |
| register "PcieRpAdvancedErrorReporting[11]" = "1" |
| # RP 12, Enable Latency Tolerance Reporting Mechanism |
| register "PcieRpLtrEnable[11]" = "1" |
| # RP 12 uses CLK SRC 2 |
| register "PcieRpClkSrcNumber[11]" = "2" |
| |
| register "usb2_ports[0]" = "USB2_PORT_LONG(OC0)" # Type-C |
| register "usb2_ports[1]" = "USB2_PORT_MID(OC3)" # Type-A Rear |
| register "usb2_ports[2]" = "USB2_PORT_MID(OC2)" # Type-A Front |
| register "usb2_ports[3]" = "USB2_PORT_MID(OC2)" # Type-A Front |
| register "usb2_ports[4]" = "USB2_PORT_MID(OC1)" # Type-A Rear |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC1)" # Type-A Rear |
| register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Type-A 2.0 / Debug |
| |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # Type-C |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Rear |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Front |
| register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Front |
| register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC1)" # Type-A Rear |
| register "usb3_ports[5]" = "USB3_PORT_DEFAULT(OC1)" # Type-A Rear |
| |
| register "i2c_voltage[0]" = "I2C_VOLTAGE_3V3" # HDMI CEC |
| register "i2c_voltage[1]" = "I2C_VOLTAGE_3V3" # TPM |
| register "i2c_voltage[2]" = "I2C_VOLTAGE_3V3" # Debug |
| register "i2c_voltage[5]" = "I2C_VOLTAGE_1V8" # Audio |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C5 | Audio | |
| #+-------------------+---------------------------+ |
| |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 194, |
| .scl_hcnt = 100, |
| .sda_hold = 36, |
| }, |
| }, |
| }" |
| |
| # Must leave UART0 enabled or SD/eMMC will not work as PCI |
| register "SerialIoDevMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C2] = PchSerialIoPci, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| [PchSerialIoIndexSpi0] = PchSerialIoPci, |
| [PchSerialIoIndexSpi1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUart0] = PchSerialIoSkipInit, |
| [PchSerialIoIndexUart1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUart2] = PchSerialIoSkipInit, |
| }" |
| |
| register "power_limits_config" = "{ |
| .tdp_psyspl2 = 90, |
| .psys_pmax = 120, |
| }" |
| register "tcc_offset" = "6" # TCC of 94C |
| |
| device cpu_cluster 0 on end |
| device domain 0 on |
| device pci 00.0 on end # Host Bridge |
| device pci 02.0 on end # Integrated Graphics Device |
| device pci 04.0 on end # SA thermal subsystem |
| device pci 14.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Root Hub"" |
| register "type" = "UPC_TYPE_HUB" |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Rear"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| device usb 2.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Rear Left"" |
| register "type" = "UPC_TYPE_A" |
| device usb 2.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Rear Right"" |
| register "type" = "UPC_TYPE_A" |
| device usb 2.4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Rear Middle"" |
| register "type" = "UPC_TYPE_A" |
| device usb 2.5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Rear"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| device usb 3.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Rear Left"" |
| register "type" = "UPC_TYPE_USB3_A" |
| device usb 3.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Rear Right"" |
| register "type" = "UPC_TYPE_USB3_A" |
| device usb 3.4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Rear Middle"" |
| register "type" = "UPC_TYPE_USB3_A" |
| device usb 3.5 on end |
| end |
| end |
| end |
| end # USB xHCI |
| device pci 14.1 off end # USB xDCI (OTG) |
| device pci 14.2 on end # Thermal Subsystem |
| device pci 14.3 off end # Camera |
| device pci 15.0 on end # I2C #0 |
| device pci 15.1 off end # I2C #1 |
| device pci 15.2 on end # I2C #2 |
| device pci 15.3 off end # I2C #3 |
| device pci 16.0 on end # Management Engine Interface 1 |
| device pci 16.1 off end # Management Engine Interface 2 |
| device pci 16.2 off end # Management Engine IDE-R |
| device pci 16.3 off end # Management Engine KT Redirection |
| device pci 16.4 off end # Management Engine Interface 3 |
| device pci 17.0 on end # SATA |
| device pci 19.0 on end # UART #2 |
| device pci 19.1 on end # I2C #5 |
| device pci 19.2 off end # I2C #4 |
| device pci 1c.0 on end # PCI Express Port 1 |
| device pci 1c.1 off end # PCI Express Port 2 |
| # PCI Express Port 3 for LAN, will be swapped to port 1 by FSP |
| device pci 1c.2 on |
| chip drivers/net |
| register "customized_leds" = "0x0fa5" |
| register "wake" = "GPE0_PCI_EXP" |
| device pci 00.0 on end |
| register "device_index" = "0" |
| end |
| end # PCI Express Port 3 |
| device pci 1c.3 on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PCI_EXP" |
| device pci 00.0 on end |
| end |
| end # PCI Express Port 4 for WLAN |
| device pci 1c.4 on end # PCI Express Port 5 for NVMe |
| device pci 1c.5 off end # PCI Express Port 6 |
| device pci 1c.6 off end # PCI Express Port 7 |
| device pci 1c.7 off end # PCI Express Port 8 |
| device pci 1d.0 on # PCI Express Port 9 for 2nd LAN |
| chip drivers/net |
| register "customized_leds" = "0x0fa5" |
| register "device_index" = "1" |
| device pci 00.0 on end |
| end |
| end # PCI Express Port 9 for BtoB |
| device pci 1d.1 off end # PCI Express Port 10 |
| device pci 1d.2 on end # PCI Express Port 11 |
| device pci 1d.3 on end # PCI Express Port 12 |
| device pci 1e.0 on end # UART #0 |
| device pci 1e.1 off end # UART #1 |
| device pci 1e.2 on |
| chip drivers/spi/acpi |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "compat_string" = ""google,cr50"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E0_IRQ)" |
| device spi 0 on end |
| end |
| end # GSPI #0 |
| device pci 1e.3 off end # GSPI #1 |
| device pci 1e.4 off end # eMMC |
| device pci 1e.5 off end # SDIO |
| device pci 1e.6 on end # SDCard |
| device pci 1f.0 on |
| chip ec/google/chromeec |
| device pnp 0c09.0 on end |
| end |
| end # LPC Interface |
| device pci 1f.1 on end # P2SB |
| device pci 1f.2 on end # Power Management Controller |
| device pci 1f.3 on end # Intel HDA |
| device pci 1f.4 on end # SMBus |
| device pci 1f.5 on end # PCH SPI |
| device pci 1f.6 off end # GbE |
| end |
| end |