| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2008-2009 coresystems GmbH |
| * Copyright (C) 2016 Damien Zammit <damien@zamaudio.com> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; version 2 of |
| * the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| #include <console/console.h> |
| #include <device/device.h> |
| #include <device/pci.h> |
| #include <device/pci_ops.h> |
| #include <device/pci_ids.h> |
| #include "chip.h" |
| #include "i82801gx.h" |
| #include "sata.h" |
| |
| typedef struct southbridge_intel_i82801gx_config config_t; |
| |
| static u8 get_ich7_sata_ports(void) |
| { |
| struct device *lpc; |
| |
| lpc = pcidev_on_root(31, 0); |
| |
| switch (pci_read_config16(lpc, PCI_DEVICE_ID)) { |
| case 0x27b0: |
| case 0x27b8: |
| return 0xf; |
| case 0x27b9: |
| case 0x27bd: |
| return 0x5; |
| case 0x27bc: |
| return 0x3; |
| default: |
| printk(BIOS_ERR, |
| "i82801gx_sata: error: cannot determine port config\n"); |
| return 0; |
| } |
| } |
| |
| void sata_enable(struct device *dev) |
| { |
| /* Get the chip configuration */ |
| config_t *config = dev->chip_info; |
| |
| if (config->sata_ahci) { |
| /* Set map to ahci */ |
| pci_write_config8(dev, SATA_MAP, |
| (pci_read_config8(dev, SATA_MAP) & ~0xc3) | 0x40); |
| } else { |
| /* Set map to ide */ |
| pci_write_config8(dev, SATA_MAP, |
| pci_read_config8(dev, SATA_MAP) & ~0xc3); |
| } |
| |
| /* At this point, the new pci id will appear on the bus */ |
| } |
| |
| static void sata_init(struct device *dev) |
| { |
| u32 reg32; |
| u16 reg16; |
| u32 *ahci_bar; |
| u8 ports; |
| |
| /* Get the chip configuration */ |
| config_t *config = dev->chip_info; |
| |
| printk(BIOS_DEBUG, "i82801gx_sata: initializing...\n"); |
| |
| if (config == NULL) { |
| printk(BIOS_ERR, "i82801gx_sata: error: device not in devicetree.cb!\n"); |
| return; |
| } |
| |
| /* Get ICH7 SATA port config */ |
| ports = get_ich7_sata_ports(); |
| |
| /* Enable BARs */ |
| pci_write_config16(dev, PCI_COMMAND, 0x0007); |
| |
| if (config->ide_legacy_combined) { |
| printk(BIOS_DEBUG, "SATA controller in combined mode.\n"); |
| /* No AHCI: clear AHCI base */ |
| pci_write_config32(dev, 0x24, 0x00000000); |
| /* And without AHCI BAR no memory decoding */ |
| reg16 = pci_read_config16(dev, PCI_COMMAND); |
| reg16 &= ~PCI_COMMAND_MEMORY; |
| pci_write_config16(dev, PCI_COMMAND, reg16); |
| |
| pci_write_config8(dev, 0x09, 0x80); |
| |
| /* Set timings */ |
| pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE | |
| IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS); |
| pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE | |
| IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS | |
| IDE_PPE0 | IDE_IE0 | IDE_TIME0); |
| |
| /* Sync DMA */ |
| pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0); |
| pci_write_config16(dev, IDE_SDMA_TIM, 0x0200); |
| |
| /* Set IDE I/O Configuration */ |
| reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; |
| pci_write_config32(dev, IDE_CONFIG, reg32); |
| |
| /* Combine IDE - SATA configuration */ |
| pci_write_config8(dev, SATA_MAP, 0x02); |
| |
| /* Restrict ports - 0 and 2 only available */ |
| ports &= 0x5; |
| } else if (config->sata_ahci) { |
| printk(BIOS_DEBUG, "SATA controller in AHCI mode.\n"); |
| /* Allow both Legacy and Native mode */ |
| pci_write_config8(dev, 0x09, 0x8f); |
| |
| /* Set Interrupt Line */ |
| /* Interrupt Pin is set by D31IP.PIP */ |
| pci_write_config8(dev, INTR_LN, 0x0a); |
| |
| ahci_bar = (u32 *)(pci_read_config32(dev, 0x27) & ~0x3ff); |
| ahci_bar[3] = config->sata_ports_implemented; |
| } else { |
| printk(BIOS_DEBUG, "SATA controller in plain mode.\n"); |
| /* Set Sata Controller Mode. No Mapping(?) */ |
| pci_write_config8(dev, SATA_MAP, 0x00); |
| |
| /* No AHCI: clear AHCI base */ |
| pci_write_config32(dev, 0x24, 0x00000000); |
| |
| /* And without AHCI BAR no memory decoding */ |
| reg16 = pci_read_config16(dev, PCI_COMMAND); |
| reg16 &= ~PCI_COMMAND_MEMORY; |
| pci_write_config16(dev, PCI_COMMAND, reg16); |
| |
| /* Native mode capable on both primary and secondary (0xa) |
| * or'ed with enabled (0x50) = 0xf |
| */ |
| pci_write_config8(dev, 0x09, 0x8f); |
| |
| /* Set Interrupt Line */ |
| /* Interrupt Pin is set by D31IP.PIP */ |
| pci_write_config8(dev, INTR_LN, 0xff); |
| |
| /* Set timings */ |
| pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE | |
| IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS | |
| IDE_PPE0 | IDE_IE0 | IDE_TIME0); |
| pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE | |
| IDE_SITRE | IDE_ISP_3_CLOCKS | |
| IDE_RCT_1_CLOCKS | IDE_IE0 | IDE_TIME0); |
| |
| /* Sync DMA */ |
| pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0 | IDE_PSDE0); |
| pci_write_config16(dev, IDE_SDMA_TIM, 0x0201); |
| |
| /* Set IDE I/O Configuration */ |
| reg32 = SIG_MODE_PRI_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0; |
| pci_write_config32(dev, IDE_CONFIG, reg32); |
| } |
| |
| /* Set port control */ |
| pci_write_config8(dev, SATA_PCS, ports); |
| |
| /* Enable clock gating for unused ports and set initialization reg */ |
| pci_write_config32(dev, SATA_IR, SIF3(ports) | SIF2 | SIF1 | SCRE); |
| |
| /* All configurations need this SATA initialization sequence */ |
| pci_write_config8(dev, 0xa0, 0x40); |
| pci_write_config8(dev, 0xa6, 0x22); |
| pci_write_config8(dev, 0xa0, 0x78); |
| pci_write_config8(dev, 0xa6, 0x22); |
| pci_write_config8(dev, 0xa0, 0x88); |
| reg32 = pci_read_config32(dev, 0xa4); |
| reg32 &= 0xc0c0c0c0; |
| reg32 |= 0x1b1b1212; |
| pci_write_config32(dev, 0xa4, reg32); |
| pci_write_config8(dev, 0xa0, 0x8c); |
| reg32 = pci_read_config32(dev, 0xa4); |
| reg32 &= 0xc0c0ff00; |
| reg32 |= 0x121200aa; |
| pci_write_config32(dev, 0xa4, reg32); |
| pci_write_config8(dev, 0xa0, 0x00); |
| |
| pci_write_config8(dev, PCI_INTERRUPT_LINE, 0); |
| |
| /* Sata Initialization Register */ |
| reg32 = pci_read_config32(dev, SATA_IR); |
| reg32 |= SCRD; // due to some bug |
| pci_write_config32(dev, SATA_IR, reg32); |
| } |
| |
| static struct pci_operations sata_pci_ops = { |
| .set_subsystem = pci_dev_set_subsystem, |
| }; |
| |
| static struct device_operations sata_ops = { |
| .read_resources = pci_dev_read_resources, |
| .set_resources = pci_dev_set_resources, |
| .enable_resources = pci_dev_enable_resources, |
| .init = sata_init, |
| .scan_bus = 0, |
| .enable = i82801gx_enable, |
| .ops_pci = &sata_pci_ops, |
| }; |
| |
| static const unsigned short sata_ids[] = { |
| 0x27c0, /* Desktop Non-AHCI and Non-RAID Mode: 82801GB/GR/GDH (ICH7/ICH7R/ICH7DH) */ |
| 0x27c1, /* Desktop AHCI Mode: 82801GB/GR/GDH (ICH7/ICH7R/ICH7DH) */ |
| 0x27c4, /* Mobile Non-AHCI and Non-RAID Mode: 82801GBM/GHM (ICH7-M/ICH7-M DH) */ |
| 0x27c5, /* Mobile AHCI Mode: 82801GBM/GHM (ICH7-M/ICH7-M DH) */ |
| /* NOTE: Any of the below are not properly supported yet. */ |
| 0x27c3, /* Desktop RAID mode: 82801GB/GR/GDH (ICH7/ICH7R/ICH7DH) */ |
| 0x27c6, /* ICH7M DH Raid Mode: 82801GHM (ICH7-M DH) */ |
| 0 |
| }; |
| |
| static const struct pci_driver i82801gx_sata_driver __pci_driver = { |
| .ops = &sata_ops, |
| .vendor = PCI_VENDOR_ID_INTEL, |
| .devices = sata_ids, |
| }; |