| # SPDX-License-Identifier: GPL-2.0-or-later |
| fw_config |
| field TOUCHPAD 26 |
| option REGULAR_TOUCHPAD 1 |
| option NUMPAD_TOUCHPAD 0 |
| end |
| end |
| |
| chip soc/amd/picasso |
| |
| # Set FADT Configuration |
| register "common_config.fadt_boot_arch" = "ACPI_FADT_LEGACY_DEVICES | ACPI_FADT_8042" |
| # See table 5-34 ACPI 6.3 spec |
| register "common_config.fadt_flags" = "ACPI_FADT_SLEEP_BUTTON | ACPI_FADT_SEALED_CASE" |
| |
| # ACP Configuration |
| register "common_config.acp_config" = "{ |
| .acp_pin_cfg = I2S_PINS_I2S_TDM, |
| .acp_i2s_wake_enable = 0, |
| .acp_pme_enable = 0, |
| }" |
| |
| # Start : OPN Performance Configuration |
| # (Configuration that is common for all variants) |
| # For the below fields, 0 indicates use SOC default |
| |
| # PROCHOT_L de-assertion Ramp Time |
| register "prochot_l_deassertion_ramp_time_ms" = "20" |
| |
| # Lower die temperature limit |
| register "thermctl_limit_degreeC" = "100" |
| |
| # FP5 Processor Voltage Supply PSI Currents |
| register "psi0_current_limit_mA" = "18000" |
| register "psi0_soc_current_limit_mA" = "12000" |
| register "vddcr_soc_voltage_margin_mV" = "0" |
| register "vddcr_vdd_voltage_margin_mV" = "0" |
| |
| # VRM Limits |
| register "vrm_maximum_current_limit_mA" = "0" |
| register "vrm_soc_maximum_current_limit_mA" = "0" |
| register "vrm_current_limit_mA" = "0" |
| register "vrm_soc_current_limit_mA" = "0" |
| |
| # Misc SMU settings |
| register "sb_tsi_alert_comparator_mode_en" = "0" |
| register "core_dldo_bypass" = "1" |
| register "min_soc_vid_offset" = "0" |
| register "aclk_dpm0_freq_400MHz" = "0" |
| |
| # End : OPN Performance Configuration |
| |
| register "emmc_config" = "{ |
| .timing = SD_EMMC_EMMC_HS400, |
| .sdr104_hs400_driver_strength = SD_EMMC_DRIVE_STRENGTH_A, |
| /* |
| * The reference design was missing a pull-up on the CMD line. |
| * This means we can't run at the full 400 kHz. By setting this |
| * to 1 we run at the slowest frequency possible by the |
| * controller (~97 kHz). |
| * |
| * Boards that have the pull-up should correctly set this. |
| */ |
| .init_khz_preset = 1, |
| }" |
| |
| register "has_usb2_phy_tune_params" = "1" |
| |
| # Controller0 Port0 Default |
| register "usb_2_port_tune_params[0]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x03, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x6, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Controller0 Port1 Default |
| register "usb_2_port_tune_params[1]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x03, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x6, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Controller0 Port2 Default |
| register "usb_2_port_tune_params[2]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x03, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x6, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Controller0 Port3 Default |
| register "usb_2_port_tune_params[3]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x03, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x6, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Controller1 Port0 Default |
| register "usb_2_port_tune_params[4]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x02, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x5, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Controller1 Port1 Default |
| register "usb_2_port_tune_params[5]" = "{ |
| .com_pds_tune = 0x07, |
| .sq_rx_tune = 0x3, |
| .tx_fsls_tune = 0x3, |
| .tx_pre_emp_amp_tune = 0x02, |
| .tx_pre_emp_pulse_tune = 0x0, |
| .tx_rise_tune = 0x1, |
| .tx_vref_tune = 0x5, |
| .tx_hsxv_tune = 0x3, |
| .tx_res_tune = 0x01, |
| }" |
| |
| # Start RV2 USB3 PHY Parameters |
| register "usb3_phy_override" = "0" |
| |
| # USB3 Port0 Default |
| register "usb3_phy_tune_params[0]" = "{ |
| .rx_eq_delta_iq_ovrd_val = 0x0, |
| .rx_eq_delta_iq_ovrd_en = 0x0, |
| }" |
| |
| # USB3 Port1 Default |
| register "usb3_phy_tune_params[1]" = "{ |
| .rx_eq_delta_iq_ovrd_val = 0x0, |
| .rx_eq_delta_iq_ovrd_en = 0x0, |
| }" |
| |
| # USB3 Port2 Default |
| register "usb3_phy_tune_params[2]" = "{ |
| .rx_eq_delta_iq_ovrd_val = 0x0, |
| .rx_eq_delta_iq_ovrd_en = 0x0, |
| }" |
| |
| # USB3 Port3 Default |
| register "usb3_phy_tune_params[3]" = "{ |
| .rx_eq_delta_iq_ovrd_val = 0x0, |
| .rx_eq_delta_iq_ovrd_en = 0x0, |
| }" |
| |
| # SUP_DIG_LVL_OVRD_IN Default |
| register "usb3_rx_vref_ctrl" = "0x10" |
| register "usb3_rx_vref_ctrl_en" = "0x00" |
| register "usb_3_tx_vboost_lvl" = "0x07" |
| register "usb_3_tx_vboost_lvl_en" = "0x00" |
| |
| # SUPX_DIG_LVL_OVRD_IN Default |
| register "usb_3_rx_vref_ctrl_x" = "0x10" |
| register "usb_3_rx_vref_ctrl_en_x" = "0x00" |
| register "usb_3_tx_vboost_lvl_x" = "0x07" |
| register "usb_3_tx_vboost_lvl_en_x" = "0x00" |
| |
| # End RV2 USB3 phy setting |
| |
| # USB OC pin mapping |
| register "usb_port_overcurrent_pin[0]" = "USB_OC_PIN_0" # USB C0 |
| register "usb_port_overcurrent_pin[1]" = "USB_OC_PIN_1" # USB C1 |
| register "usb_port_overcurrent_pin[2]" = "USB_OC_PIN_0" # USB A0 |
| register "usb_port_overcurrent_pin[3]" = "USB_OC_PIN_1" # USB A1 |
| register "usb_port_overcurrent_pin[4]" = "USB_OC_NONE" # Camera |
| register "usb_port_overcurrent_pin[5]" = "USB_OC_NONE" # Bluetooth |
| |
| # eSPI Configuration |
| register "common_config.espi_config" = "{ |
| .std_io_decode_bitmap = ESPI_DECODE_IO_0x80_EN | ESPI_DECODE_IO_0X60_0X64_EN, |
| .generic_io_range[0] = { |
| .base = 0x62, |
| /* |
| * Only 0x62 and 0x66 are required. But, this is not supported by |
| * standard IO decodes and there are only 4 generic I/O windows |
| * available. Hence, open a window from 0x62-0x67. |
| */ |
| .size = 5, |
| }, |
| .generic_io_range[1] = { |
| .base = 0x800, /* EC_HOST_CMD_REGION0 */ |
| .size = 256, /* EC_HOST_CMD_REGION_SIZE * 2 */ |
| }, |
| .generic_io_range[2] = { |
| .base = 0x900, /* EC_LPC_ADDR_MEMMAP */ |
| .size = 255, /* EC_MEMMAP_SIZE */ |
| }, |
| .generic_io_range[3] = { |
| .base = 0x200, /* EC_LPC_ADDR_HOST_DATA */ |
| .size = 8, /* 0x200 - 0x207 */ |
| }, |
| |
| .io_mode = ESPI_IO_MODE_QUAD, |
| .op_freq_mhz = ESPI_OP_FREQ_33_MHZ, |
| .crc_check_enable = 1, |
| .alert_pin = ESPI_ALERT_PIN_PUSH_PULL, |
| .periph_ch_en = 1, |
| .vw_ch_en = 1, |
| .oob_ch_en = 0, |
| .flash_ch_en = 0, |
| |
| .vw_irq_polarity = ESPI_VW_IRQ_LEVEL_HIGH(1) | ESPI_VW_IRQ_LEVEL_HIGH(12), |
| }" |
| |
| register "i2c_scl_reset" = "GPIO_I2C2_SCL | GPIO_I2C3_SCL" |
| |
| # general purpose PCIe clock output configuration |
| register "gpp_clk_config[0]" = "GPP_CLK_REQ" # WLAN |
| register "gpp_clk_config[1]" = "GPP_CLK_REQ" # SD Reader |
| register "gpp_clk_config[2]" = "GPP_CLK_REQ" # NVME SSD |
| register "gpp_clk_config[3]" = "GPP_CLK_OFF" |
| register "gpp_clk_config[4]" = "GPP_CLK_OFF" |
| register "gpp_clk_config[5]" = "GPP_CLK_OFF" |
| register "gpp_clk_config[6]" = "GPP_CLK_OFF" |
| |
| register "pspp_policy" = "DXIO_PSPP_BALANCED" |
| |
| # See AMD 55570-B1 Table 13: PCI Device ID Assignments. |
| device domain 0 on |
| subsystemid 0x1022 0x1510 inherit |
| device ref iommu on end |
| device ref gpp_bridge_1 on # Wifi |
| chip drivers/wifi/generic |
| register "wake" = "GEVENT_8" |
| device pci 00.0 on end |
| end |
| end |
| device ref gpp_bridge_2 on end # SD |
| device ref internal_bridge_a on |
| device ref gfx on end # Internal GPU |
| device ref gfx_hda on end # Display HDA |
| device ref crypto on end # Crypto Coprocessor |
| device ref xhci_0 on # USB 3.1 |
| chip drivers/usb/acpi |
| register "desc" = ""Root Hub"" |
| register "type" = "UPC_TYPE_HUB" |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device usb 2.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 2.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device usb 2.2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device usb 2.3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""User-Facing Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_143)" |
| device usb 2.5 alias xhci0_bt on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device usb 3.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 3.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device usb 3.2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device usb 3.3 on end |
| end |
| end |
| end |
| end |
| device ref acp on |
| chip drivers/amd/i2s_machine_dev |
| register "hid" = ""AMDI5682"" |
| # DMIC select GPIO for ACP machine device |
| # This GPIO is used to select DMIC0 or DMIC1 by the |
| # kernel driver. It does not really have a polarity |
| # since low and high control the selection of DMIC and |
| # hence does not have an active polarity. |
| # Kernel driver does not use the polarity field and |
| # instead treats the GPIO selection as follows: |
| # Set low (0) = Select DMIC0 |
| # Set high (1) = Select DMIC1 |
| register "dmic_select_gpio" = "ACPI_GPIO_OUTPUT(GPIO_67)" |
| device generic 0.0 alias acp_machine hidden end |
| end |
| end # Audio |
| device ref hda off end # HDA |
| device ref mp2 on end # non-Sensor Fusion Hub device |
| end |
| device ref lpc_bridge on |
| chip ec/google/chromeec |
| device pnp 0c09.0 alias cros_ec on |
| chip ec/google/chromeec/i2c_tunnel |
| register "uid" = "1" |
| register "remote_bus" = "8" |
| device generic 0.0 alias cros_ec_i2c_8 on |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5682"" |
| register "name" = ""RT58"" |
| register "uid" = "1" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPIO_84)" |
| register "property_count" = "2" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| register "property_list[1].type" = "ACPI_DP_TYPE_STRING" |
| register "property_list[1].name" = ""realtek,mclk-name"" |
| register "property_list[1].string" = ""oscout1"" |
| device i2c 1a alias audio_rt5682 on end |
| end |
| end |
| end |
| chip ec/google/chromeec/audio_codec |
| register "uid" = "1" |
| device generic 0 on end |
| end |
| end |
| end |
| end |
| end # domain |
| |
| device ref i2c_3 hidden |
| chip drivers/i2c/tpm |
| register "hid" = ""GOOG0005"" |
| register "desc" = ""Cr50 TPM"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_3)" |
| device i2c 50 on end |
| end |
| end |
| |
| device ref uart_0 on end # console |
| |
| device ref emmc on end |
| |
| end # chip soc/amd/picasso |