| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <stdint.h> |
| #include <arch/io.h> |
| #include <device/pci_ops.h> |
| #include <device/device.h> |
| #include <device/pci.h> |
| |
| #include "gpio.h" |
| |
| #define MAX_GPIO_NUMBER 75 /* zero based */ |
| |
| /* LPC GPIO Base Address Register */ |
| #define GPIO_BASE 0x48 |
| |
| /* PCI Configuration Space (D31:F0): LPC */ |
| #if defined(__SIMPLE_DEVICE__) |
| #define PCH_LPC_DEV PCI_DEV(0, 0x1f, 0) |
| #else |
| #define PCH_LPC_DEV pcidev_on_root(0x1f, 0) |
| #endif |
| |
| static u16 get_gpio_base(void) |
| { |
| #ifdef __SIMPLE_DEVICE__ |
| /* Don't assume GPIO_BASE is still the same */ |
| return pci_read_config16(PCH_LPC_DEV, GPIO_BASE) & 0xfffe; |
| #else |
| static u16 gpiobase; |
| |
| if (gpiobase) |
| return gpiobase; |
| |
| gpiobase = pci_read_config16(PCH_LPC_DEV, GPIO_BASE) & 0xfffe; |
| |
| return gpiobase; |
| #endif |
| } |
| |
| void setup_pch_gpios(const struct pch_gpio_map *gpio) |
| { |
| u16 gpiobase = get_gpio_base(); |
| |
| /* The order of these calls does matter on ICH9M and prior. |
| * The level has to be set on pins configured as gpio, |
| * but on newer platforms we want to change the level first |
| * to make sure there are no glitches on the lines ! |
| * Write the gpio level twice to satisfy both requirements. |
| */ |
| |
| /* GPIO Set 1 */ |
| if (gpio->set1.level) |
| outl(*((u32 *)gpio->set1.level), gpiobase + GP_LVL); |
| if (gpio->set1.mode) |
| outl(*((u32 *)gpio->set1.mode), gpiobase + GPIO_USE_SEL); |
| if (gpio->set1.direction) |
| outl(*((u32 *)gpio->set1.direction), gpiobase + GP_IO_SEL); |
| if (gpio->set1.level) |
| outl(*((u32 *)gpio->set1.level), gpiobase + GP_LVL); |
| if (gpio->set1.reset) |
| outl(*((u32 *)gpio->set1.reset), gpiobase + GP_RST_SEL1); |
| if (gpio->set1.invert) |
| outl(*((u32 *)gpio->set1.invert), gpiobase + GPI_INV); |
| if (gpio->set1.blink) |
| outl(*((u32 *)gpio->set1.blink), gpiobase + GPO_BLINK); |
| |
| /* GPIO Set 2 */ |
| if (gpio->set2.level) |
| outl(*((u32 *)gpio->set2.level), gpiobase + GP_LVL2); |
| if (gpio->set2.mode) |
| outl(*((u32 *)gpio->set2.mode), gpiobase + GPIO_USE_SEL2); |
| if (gpio->set2.direction) |
| outl(*((u32 *)gpio->set2.direction), gpiobase + GP_IO_SEL2); |
| if (gpio->set2.level) |
| outl(*((u32 *)gpio->set2.level), gpiobase + GP_LVL2); |
| if (gpio->set2.reset) |
| outl(*((u32 *)gpio->set2.reset), gpiobase + GP_RST_SEL2); |
| |
| /* GPIO Set 3 */ |
| if (gpio->set3.level) |
| outl(*((u32 *)gpio->set3.level), gpiobase + GP_LVL3); |
| if (gpio->set3.mode) |
| outl(*((u32 *)gpio->set3.mode), gpiobase + GPIO_USE_SEL3); |
| if (gpio->set3.direction) |
| outl(*((u32 *)gpio->set3.direction), gpiobase + GP_IO_SEL3); |
| if (gpio->set3.level) |
| outl(*((u32 *)gpio->set3.level), gpiobase + GP_LVL3); |
| if (gpio->set3.reset) |
| outl(*((u32 *)gpio->set3.reset), gpiobase + GP_RST_SEL3); |
| } |
| |
| /* |
| * return current gpio level. |
| */ |
| int get_gpio(int gpio_num) |
| { |
| static const int gpio_reg_offsets[] = {GP_LVL, GP_LVL2, GP_LVL3}; |
| u16 gpio_base = get_gpio_base(); |
| int index, bit; |
| |
| if (gpio_num > MAX_GPIO_NUMBER) |
| return 0; /* Just ignore wrong gpio numbers. */ |
| |
| index = gpio_num / 32; |
| bit = gpio_num % 32; |
| |
| return (inl(gpio_base + gpio_reg_offsets[index]) >> bit) & 1; |
| } |
| |
| /* |
| * get a number comprised of multiple GPIO values. gpio_num_array points to |
| * the array of gpio pin numbers to scan, terminated by -1. |
| */ |
| unsigned int get_gpios(const int *gpio_num_array) |
| { |
| int gpio; |
| unsigned int bitmask = 1; |
| unsigned int vector = 0; |
| |
| while (bitmask && |
| ((gpio = *gpio_num_array++) != -1)) { |
| if (get_gpio(gpio)) |
| vector |= bitmask; |
| bitmask <<= 1; |
| } |
| return vector; |
| } |
| |
| /* |
| * set gpio output to level. |
| */ |
| void set_gpio(int gpio_num, int value) |
| { |
| static const int gpio_reg_offsets[] = { |
| GP_LVL, GP_LVL2, GP_LVL3 |
| }; |
| u16 gpio_base = get_gpio_base(); |
| int index, bit; |
| u32 config; |
| |
| if (gpio_num > MAX_GPIO_NUMBER) |
| return; /* Just ignore wrong gpio numbers. */ |
| |
| index = gpio_num / 32; |
| bit = gpio_num % 32; |
| |
| config = inl(gpio_base + gpio_reg_offsets[index]); |
| config &= ~(1 << bit); |
| if (value != 0) |
| config |= (1 << bit); |
| outl(config, gpio_base + gpio_reg_offsets[index]); |
| } |
| |
| int gpio_is_native(int gpio_num) |
| { |
| static const int gpio_reg_offsets[] = { |
| GPIO_USE_SEL, GPIO_USE_SEL2, GPIO_USE_SEL3 |
| }; |
| u16 gpio_base = get_gpio_base(); |
| int index, bit; |
| u32 config; |
| |
| if (gpio_num > MAX_GPIO_NUMBER) |
| return 0; /* Just ignore wrong gpio numbers. */ |
| |
| index = gpio_num / 32; |
| bit = gpio_num % 32; |
| |
| config = inl(gpio_base + gpio_reg_offsets[index]); |
| return !(config & (1 << bit)); |
| } |