| chip soc/intel/alderlake |
| # Acoustic settings |
| register "acoustic_noise_mitigation" = "1" |
| register "slow_slew_rate[VR_DOMAIN_IA]" = "SLEW_FAST_8" |
| register "slow_slew_rate[VR_DOMAIN_GT]" = "SLEW_FAST_8" |
| register "fast_pkg_c_ramp_disable[VR_DOMAIN_IA]" = "1" |
| register "fast_pkg_c_ramp_disable[VR_DOMAIN_GT]" = "1" |
| register "PreWake" = "100" |
| |
| register "sagv" = "SaGv_Enabled" |
| |
| # EMMC Tx CMD Delay |
| # Refer to EDS-Vol2-42.3.7. |
| # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" |
| |
| # EMMC TX DATA Delay 1 |
| # Refer to EDS-Vol2-42.3.8. |
| # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. |
| # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" |
| |
| # EMMC TX DATA Delay 2 |
| # Refer to EDS-Vol2-42.3.9. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. |
| # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828" |
| |
| # EMMC RX CMD/DATA Delay 1 |
| # Refer to EDS-Vol2-42.3.10. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. |
| # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F1B" |
| |
| # EMMC RX CMD/DATA Delay 2 |
| # Refer to EDS-Vol2-42.3.12. |
| # [17:16] stands for Rx Clock before Output Buffer, |
| # 00: Rx clock after output buffer, |
| # 01: Rx clock before output buffer, |
| # 10: Automatic selection based on working mode. |
| # 11: Reserved |
| # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10023" |
| |
| # EMMC Rx Strobe Delay |
| # Refer to EDS-Vol2-42.3.11. |
| # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. |
| # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x11515" |
| |
| # SOC Aux orientation override: |
| # This is a bitfield that corresponds to up to 4 TCSS ports. |
| # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2. |
| # TcssAuxOri = 0101b |
| # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports |
| # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the |
| # motherboard to USBC connector |
| register "tcss_aux_ori" = "5" |
| |
| register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" |
| register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" |
| |
| register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C0 |
| register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C1 |
| register "usb2_ports[3]" = "USB2_PORT_MID(OC_SKIP)" # USB-A1 |
| register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # WWAN |
| register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # UF Camera |
| register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # WF Camera |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN |
| |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 port for WWAN |
| |
| # Configure external V1P05/Vnn/VnnSx Rails for Pujjoga |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 1, |
| }" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| I2C0 | TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C1 | Touchscreen | |
| #| I2C2 | Sub-board(PSensor)/WCAM | |
| #| I2C3 | Audio | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST_PLUS, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .scl_lcnt = 55, |
| .scl_hcnt = 30, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 157, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 157, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| }" |
| |
| device domain 0 on |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GDIX0000"" |
| register "generic.desc" = ""Goodix Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "20" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "180" |
| register "generic.reset_off_delay_ms" = "3" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_off_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 5d on end |
| end |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F13)" |
| register "key.wake_gpe" = "GPE0_DW2_15" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" |
| register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" |
| register "key.dev_name" = ""EJCT"" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| device generic 0 on end |
| end |
| end |
| device ref i2c3 on |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| chip drivers/generic/alc1015 |
| register "hid" = ""RTL1019"" |
| register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| device generic 0 on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "wake" = "GPE0_DW2_14" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""SYNA0000"" |
| register "generic.cid" = ""ACPI0C50"" |
| register "generic.desc" = ""Synaptics Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 0x2c on end |
| end |
| end |
| device ref pcie_rp4 on |
| # PCIe 4 WLAN |
| register "pch_pcie_rp[PCH_RP(4)]" = "{ |
| .clk_src = 2, |
| .clk_req = 2, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_DW1_03" |
| register "add_acpi_dma_property" = "true" |
| device pci 00.0 on end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port2 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port2 on end |
| |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb2_port4 on end |
| end |
| |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 UFC"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 WFC"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port7 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port8 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""CNVi Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb3_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb3_port3 on end |
| end |
| end |
| end |
| end |
| end |
| end |