| chip soc/intel/skylake |
| |
| device domain 0 on |
| device ref south_xhci on |
| register "usb2_ports" = "{ |
| [0] = USB2_PORT_TYPE_C(OC0), // Type-C Port 1 |
| [1] = USB2_PORT_FLEX(OC_SKIP), // Camera |
| [2] = USB2_PORT_MID(OC_SKIP), // Bluetooth |
| [4] = USB2_PORT_MID(OC2), // Type-A Port (card) |
| [5] = USB2_PORT_MID(OC_SKIP), // SD |
| [8] = USB2_PORT_LONG(OC3), // Type-A Port (board) |
| }" |
| |
| register "usb3_ports" = "{ |
| [0] = USB3_PORT_DEFAULT(OC0), // Type-C Port 1 |
| [1] = USB3_PORT_DEFAULT(OC_SKIP), // SD |
| [2] = USB3_PORT_DEFAULT(OC2), // Type-A Port (card) |
| [3] = USB3_PORT_DEFAULT(OC3), // Type-A Port (board) |
| }" |
| end |
| device ref i2c0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0001"" |
| register "desc" = ""ELAN Touchscreen"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" |
| register "detect" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E7)" |
| register "reset_delay_ms" = "20" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E23)" |
| register "enable_delay_ms" = "1" |
| register "has_power_resource" = "1" |
| device i2c 10 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""MLFS0000"" |
| register "desc" = ""Melfas Touchscreen"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" |
| register "detect" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E7)" |
| register "reset_delay_ms" = "10" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E23)" |
| register "enable_delay_ms" = "55" |
| register "has_power_resource" = "1" |
| device i2c 34 on end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" |
| register "wake" = "GPE0_DW0_05" |
| device i2c 15 on end |
| end |
| end |
| device ref i2c4 on |
| chip drivers/i2c/nau8825 |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F10_IRQ)" |
| register "jkdet_enable" = "1" |
| register "jkdet_pull_enable" = "1" |
| register "jkdet_pull_up" = "1" |
| register "jkdet_polarity" = "1" # ActiveLow |
| register "vref_impedance" = "2" # 125kOhm |
| register "micbias_voltage" = "6" # 2.754 |
| register "sar_threshold_num" = "4" |
| register "sar_threshold[0]" = "0x08" |
| register "sar_threshold[1]" = "0x12" |
| register "sar_threshold[2]" = "0x26" |
| register "sar_threshold[3]" = "0x73" |
| register "sar_hysteresis" = "0" |
| register "sar_voltage" = "6" |
| register "sar_compare_time" = "1" # 1us |
| register "sar_sampling_time" = "1" # 4us |
| register "short_key_debounce" = "3" # 30ms |
| register "jack_insert_debounce" = "7" # 512ms |
| register "jack_eject_debounce" = "0" |
| device i2c 1a on end |
| end |
| end |
| device ref hda on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98357A"" |
| register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B2)" |
| register "sdmode_delay" = "5" |
| device generic 0 on end |
| end |
| end |
| end |
| end |