| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <arch/mmu.h> |
| #include <device/device.h> |
| #include <soc/addressmap.h> |
| #include <soc/clk_rst.h> |
| #include <soc/clock.h> |
| #include <soc/funitcfg.h> |
| #include <soc/nvidia/tegra/i2c.h> |
| #include <soc/padconfig.h> |
| #include <soc/spi.h> |
| #include <soc/nvidia/tegra/dc.h> |
| #include <soc/display.h> |
| |
| #include <vendorcode/google/chromeos/chromeos.h> |
| |
| static const struct pad_config sdmmc1_pad[] = { |
| /* MMC1(SDCARD) */ |
| PAD_CFG_SFIO(SDMMC1_CLK, PINMUX_INPUT_ENABLE, SDMMC1), |
| PAD_CFG_SFIO(SDMMC1_CMD, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SDMMC1), |
| PAD_CFG_SFIO(SDMMC1_DAT0, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SDMMC1), |
| PAD_CFG_SFIO(SDMMC1_DAT1, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SDMMC1), |
| PAD_CFG_SFIO(SDMMC1_DAT2, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SDMMC1), |
| PAD_CFG_SFIO(SDMMC1_DAT3, PINMUX_INPUT_ENABLE | PINMUX_PULL_UP, SDMMC1), |
| /* MMC1 Card Detect pin */ |
| PAD_CFG_GPIO_INPUT(GPIO_PZ1, PINMUX_PULL_UP), |
| /* Disable SD card reader power so it can be reset even on warm boot. |
| Payloads must enable power before accessing SD card slots. */ |
| PAD_CFG_GPIO_OUT0(GPIO_PZ4, PINMUX_PULL_NONE), |
| }; |
| |
| static const struct pad_config audio_codec_pads[] = { |
| /* GPIO_X1_AUD(BB3) is AUDIO_LDO_EN (->CODEC RESET_N pin) */ |
| PAD_CFG_GPIO_OUT1(GPIO_X1_AUD, PINMUX_PULL_DOWN), |
| }; |
| |
| static const struct pad_config padcfgs[] = { |
| /* We pull the USB VBUS signals up but keep them as inputs since the |
| * voltage source likes to drive them low on overcurrent conditions */ |
| PAD_CFG_GPIO_INPUT(USB_VBUS_EN1, PINMUX_PULL_NONE | PINMUX_PARKED | |
| PINMUX_INPUT_ENABLE | PINMUX_LPDR | PINMUX_IO_HV), |
| |
| /* Add backlight vdd/enable/pwm/dp hpd pad cfgs here */ |
| }; |
| |
| static const struct pad_config i2c1_pad[] = { |
| /* GEN1 I2C */ |
| PAD_CFG_SFIO(GEN1_I2C_SCL, PINMUX_INPUT_ENABLE, I2C1), |
| PAD_CFG_SFIO(GEN1_I2C_SDA, PINMUX_INPUT_ENABLE, I2C1), |
| }; |
| |
| static const struct pad_config i2s1_pad[] = { |
| /* I2S1 */ |
| PAD_CFG_SFIO(DAP1_SCLK, PINMUX_INPUT_ENABLE, I2S1), |
| PAD_CFG_SFIO(DAP1_FS, PINMUX_INPUT_ENABLE, I2S1), |
| PAD_CFG_SFIO(DAP1_DOUT, PINMUX_INPUT_ENABLE, I2S1), |
| PAD_CFG_SFIO(DAP1_DIN, PINMUX_INPUT_ENABLE | PINMUX_TRISTATE, I2S1), |
| /* codec MCLK via AUD SFIO */ |
| PAD_CFG_SFIO(AUD_MCLK, PINMUX_PULL_NONE, AUD), |
| }; |
| |
| static const struct funit_cfg audio_funit[] = { |
| /* We need 1.5MHz for I2S1. So we use CLK_M */ |
| FUNIT_CFG(I2S1, CLK_M, 1500, i2s1_pad, ARRAY_SIZE(i2s1_pad)), |
| }; |
| |
| static const struct funit_cfg funitcfgs[] = { |
| FUNIT_CFG(SDMMC1, PLLP, 48000, sdmmc1_pad, ARRAY_SIZE(sdmmc1_pad)), |
| FUNIT_CFG(SDMMC4, PLLP, 48000, NULL, 0), |
| FUNIT_CFG(I2C1, PLLP, 100, i2c1_pad, ARRAY_SIZE(i2c1_pad)), |
| FUNIT_CFG(I2C6, PLLP, 400, audio_codec_pads, ARRAY_SIZE(audio_codec_pads)), |
| FUNIT_CFG_USB(USBD), |
| }; |
| |
| /* Audio init: clocks and enables/resets */ |
| static void setup_audio(void) |
| { |
| /* Audio codec (ES755) uses OSC freq (via AUD_MCLK), s/b 38.4MHz */ |
| soc_configure_funits(audio_funit, ARRAY_SIZE(audio_funit)); |
| |
| /* |
| * As per NVIDIA hardware team, we need to take ALL audio devices |
| * connected to AHUB (AUDIO, APB2APE, I2S, SPDIF, etc.) out of reset |
| * and clock-enabled, otherwise reading AHUB devices (in our case, |
| * I2S/APBIF/AUDIO<XBAR>) will hang. |
| */ |
| soc_configure_ape(); |
| clock_enable_audio(); |
| } |
| |
| static void mainboard_init(struct device *dev) |
| { |
| soc_configure_pads(padcfgs, ARRAY_SIZE(padcfgs)); |
| soc_configure_funits(funitcfgs, ARRAY_SIZE(funitcfgs)); |
| |
| i2c_init(I2C1_BUS); |
| setup_audio(); |
| } |
| |
| static void mainboard_enable(struct device *dev) |
| { |
| dev->ops->init = &mainboard_init; |
| } |
| |
| struct chip_operations mainboard_ops = { |
| .name = "foster", |
| .enable_dev = mainboard_enable, |
| }; |