| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <console/console.h> |
| #include <device/i2c_simple.h> |
| #include <soc/mt6311.h> |
| |
| enum { |
| MT6311_SLAVE_ADDR = 0x6B, |
| }; |
| |
| static u32 get_mt6311_chip_id(uint8_t i2c_num) |
| { |
| unsigned char id[2] = {0}; |
| |
| i2c_read_field(i2c_num, MT6311_SLAVE_ADDR, MT6311_CID, |
| &id[0], 0xFF, 0); |
| i2c_read_field(i2c_num, MT6311_SLAVE_ADDR, MT6311_SWCID, |
| &id[1], 0xFF, 0); |
| |
| return (u32)(id[0] << 8 | id[1]); |
| } |
| |
| static void mt6311_hw_init(uint8_t i2c_num) |
| { |
| int ret = 0; |
| unsigned char var[3] = {0}; |
| |
| |
| /* |
| * Phase Shedding Trim Software Setting |
| * The phase 2 of MT6311 will enter PWM mode if the threshold is |
| * reached. |
| * The threshold is set according to EFUSE value. |
| */ |
| ret |= i2c_read_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_EFUSE_DOUT_56_63, &var[0], |
| 0x3, 1); |
| ret |= i2c_read_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_EFUSE_DOUT_56_63, &var[1], |
| 0x1, 7); |
| ret |= i2c_read_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_EFUSE_DOUT_64_71, &var[2], |
| 0x1, 0); |
| |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_VDVFS1_ANA_CON10, |
| var[0] | var[1] << 2 | var[2] << 3, 0xf, 0); |
| |
| /* I2C_CONFIG; pushpull setting, Opendrain is '0' */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, MT6311_TOP_INT_CON, |
| 0x1, 0x1, 2); |
| /* RG_WDTRSTB_EN; CC, initial WDRSTB setting. */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, MT6311_TOP_RST_CON, |
| 0x1, 0x1, 5); |
| /* initial INT function */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, MT6311_GPIO_MODE, |
| 0x1, 0x7, 3); |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, MT6311_STRUP_CON5, |
| 0, 1 << 2 | 1 << 1 | 1 << 0, 0); |
| |
| /* Vo max is 1.15V */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_STRUP_ANA_CON1, 0x3, 0x3, 5); |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_BUCK_ALL_CON23, 0x1, 0x1, 0); |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_STRUP_ANA_CON2, 0x3, 0x3, 0); |
| /* Suspend HW control from SPM */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_TOP_CON, 0x1, 0x1, 0); |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_VDVFS11_CON7, 0x1, 0x1, 0); |
| /* default VDVFS power on */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_VDVFS11_CON9, 0x1, 0x1, 0); |
| /* for DVFS slew rate rising=0.67us */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_VDVFS11_CON10, 0x1, 0x7f, 0); |
| /* for DVFS slew rate, falling 2.0us */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_VDVFS11_CON11, 0x5, 0x7f, 0); |
| /* default VDVFS11_VOSEL 1.0V, SW control */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_VDVFS11_CON12, 0x40, 0x7f, 0); |
| /* default VDVFS11_VOSEL_ON 1.0V, HW control */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_VDVFS11_CON13, 0x40, 0x7f, 0); |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_VDVFS11_CON14, 0x40, 0x7f, 0); |
| /* for DVFS sof change, falling 50us */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_VDVFS11_CON19, 0x3, 0x3, 0); |
| /* for DVFS sof change, falling only */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_VDVFS11_CON19, 0x1, 0x3, 4); |
| /* OFF LDO */ |
| ret |= i2c_write_field(i2c_num, MT6311_SLAVE_ADDR, |
| MT6311_LDO_CON3, 0, 0x1, 0); |
| |
| if (ret) |
| printk(BIOS_ERR, "ERROR: %s failed\n", __func__); |
| } |
| |
| void mt6311_probe(uint8_t i2c_num) |
| { |
| u32 val = 0; |
| |
| /* Check device ID is MT6311 */ |
| val = get_mt6311_chip_id(i2c_num); |
| printk(BIOS_INFO, "%s: device ID = %#x\n", __func__, val); |
| |
| if (val < MT6311_E1_CID_CODE) { |
| printk(BIOS_ERR, "ERROR: unknown MT6311 device_id\n"); |
| return; |
| } |
| |
| mt6311_hw_init(i2c_num); |
| } |