| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <device/mmio.h> |
| #include <acpi/acpi.h> |
| #include <console/console.h> |
| #include <delay.h> |
| #include <device/device.h> |
| #include <drivers/i2c/designware/dw_i2c.h> |
| #include <amdblocks/acpimmio.h> |
| #include <soc/i2c.h> |
| #include <soc/iomap.h> |
| #include <soc/pci_devs.h> |
| #include <soc/southbridge.h> |
| #include "chip.h" |
| |
| /* Global to provide access to chip.c */ |
| const char *i2c_acpi_name(const struct device *dev); |
| |
| /* |
| * We don't have addresses for I2C0-1. |
| */ |
| static const uintptr_t i2c_bus_address[I2C_MASTER_DEV_COUNT + I2C_SLAVE_DEV_COUNT] = { |
| 0, |
| 0, |
| APU_I2C2_BASE, |
| APU_I2C3_BASE, |
| APU_I2C4_BASE, /* Can only be used in slave mode */ |
| }; |
| |
| uintptr_t dw_i2c_base_address(unsigned int bus) |
| { |
| if (bus >= ARRAY_SIZE(i2c_bus_address)) |
| return 0; |
| |
| return i2c_bus_address[bus]; |
| } |
| |
| const struct dw_i2c_bus_config *dw_i2c_get_soc_cfg(unsigned int bus) |
| { |
| const struct soc_amd_picasso_config *config; |
| |
| if (bus >= ARRAY_SIZE(config->i2c)) |
| return NULL; |
| |
| /* config is not NULL; if it was, config_of_soc calls die() internally */ |
| config = config_of_soc(); |
| |
| return &config->i2c[bus]; |
| } |
| |
| const char *i2c_acpi_name(const struct device *dev) |
| { |
| switch (dev->path.mmio.addr) { |
| case APU_I2C2_BASE: |
| return "I2C2"; |
| case APU_I2C3_BASE: |
| return "I2C3"; |
| case APU_I2C4_BASE: |
| return "I2C4"; |
| default: |
| return NULL; |
| } |
| } |
| |
| int dw_i2c_soc_dev_to_bus(const struct device *dev) |
| { |
| switch (dev->path.mmio.addr) { |
| case APU_I2C2_BASE: |
| return 2; |
| case APU_I2C3_BASE: |
| return 3; |
| case APU_I2C4_BASE: |
| return 4; |
| } |
| return -1; |
| } |
| |
| __weak void mainboard_i2c_override(int bus, uint32_t *pad_settings) { } |
| |
| static void dw_i2c_soc_init(bool is_early_init) |
| { |
| size_t i; |
| const struct soc_amd_picasso_config *config; |
| uint32_t pad_ctrl; |
| int misc_reg; |
| |
| /* config is not NULL; if it was, config_of_soc calls die() internally */ |
| config = config_of_soc(); |
| |
| for (i = I2C_MASTER_START_INDEX; i < ARRAY_SIZE(config->i2c); i++) { |
| const struct dw_i2c_bus_config *cfg = &config->i2c[i]; |
| |
| if (cfg->early_init != is_early_init) |
| continue; |
| |
| if (dw_i2c_init(i, cfg)) { |
| printk(BIOS_ERR, "Failed to init i2c bus %zd\n", i); |
| continue; |
| } |
| |
| misc_reg = MISC_I2C0_PAD_CTRL + sizeof(uint32_t) * i; |
| pad_ctrl = misc_read32(misc_reg); |
| |
| pad_ctrl &= ~I2C_PAD_CTRL_NG_MASK; |
| pad_ctrl |= I2C_PAD_CTRL_NG_NORMAL; |
| |
| pad_ctrl &= ~I2C_PAD_CTRL_RX_SEL_MASK; |
| pad_ctrl |= I2C_PAD_CTRL_RX_SEL_3_3V; |
| |
| pad_ctrl &= ~I2C_PAD_CTRL_FALLSLEW_MASK; |
| pad_ctrl |= cfg->speed == I2C_SPEED_STANDARD |
| ? I2C_PAD_CTRL_FALLSLEW_STD |
| : I2C_PAD_CTRL_FALLSLEW_LOW; |
| pad_ctrl |= I2C_PAD_CTRL_FALLSLEW_EN; |
| |
| mainboard_i2c_override(i, &pad_ctrl); |
| misc_write32(misc_reg, pad_ctrl); |
| } |
| } |
| |
| void i2c_soc_early_init(void) |
| { |
| dw_i2c_soc_init(true); |
| } |
| |
| void i2c_soc_init(void) |
| { |
| dw_i2c_soc_init(false); |
| } |
| |
| struct device_operations picasso_i2c_mmio_ops = { |
| /* TODO(teravest): Move I2C resource info here. */ |
| .read_resources = noop_read_resources, |
| .set_resources = noop_set_resources, |
| .scan_bus = scan_smbus, |
| .acpi_name = i2c_acpi_name, |
| .acpi_fill_ssdt = dw_i2c_acpi_fill_ssdt, |
| }; |
| |
| /* |
| * I2C pins are open drain with external pull up, so in order to bit bang them |
| * all, SCL pins must become GPIO inputs with no pull, then they need to be |
| * toggled between input-no-pull and output-low. This table is for the initial |
| * conversion of all SCL pins to input with no pull. |
| */ |
| static const struct soc_amd_gpio i2c_2_gpi[] = { |
| PAD_GPI(I2C2_SCL_PIN, PULL_NONE), |
| PAD_GPI(I2C3_SCL_PIN, PULL_NONE), |
| /* I2C4 is a slave device only */ |
| }; |
| #define saved_pins_count ARRAY_SIZE(i2c_2_gpi) |
| |
| /* |
| * To program I2C pins without destroying their programming, the registers |
| * that will be changed need to be saved first. |
| */ |
| static void save_i2c_pin_registers(uint8_t gpio, |
| struct soc_amd_i2c_save *save_table) |
| { |
| uint32_t *gpio_ptr; |
| |
| gpio_ptr = (uint32_t *)gpio_get_address(gpio); |
| save_table->mux_value = iomux_read8(gpio); |
| save_table->control_value = read32(gpio_ptr); |
| } |
| |
| static void restore_i2c_pin_registers(uint8_t gpio, |
| struct soc_amd_i2c_save *save_table) |
| { |
| uint32_t *gpio_ptr; |
| |
| gpio_ptr = (uint32_t *)gpio_get_address(gpio); |
| iomux_write8(gpio, save_table->mux_value); |
| iomux_read8(gpio); |
| write32(gpio_ptr, save_table->control_value); |
| read32(gpio_ptr); |
| } |
| |
| /* Slaves to be reset are controlled by devicetree register i2c_scl_reset */ |
| void sb_reset_i2c_slaves(void) |
| { |
| const struct soc_amd_picasso_config *cfg; |
| const struct device *dev = pcidev_path_on_root(GNB_DEVFN); |
| struct soc_amd_i2c_save save_table[saved_pins_count]; |
| uint8_t i, j, control; |
| |
| if (!dev || !dev->chip_info) |
| return; |
| cfg = dev->chip_info; |
| control = cfg->i2c_scl_reset & GPIO_I2C_MASK; |
| if (control == 0) |
| return; |
| |
| /* Save and reprogram I2C SCL pins */ |
| for (i = 0; i < saved_pins_count; i++) |
| save_i2c_pin_registers(i2c_2_gpi[i].gpio, &save_table[i]); |
| program_gpios(i2c_2_gpi, saved_pins_count); |
| |
| /* |
| * Toggle SCL back and forth 9 times under 100KHz. A single read is |
| * needed after the writes to force the posted write to complete. |
| */ |
| for (j = 0; j < 9; j++) { |
| if (control & GPIO_I2C2_SCL) |
| write32((uint32_t *)GPIO_I2C2_ADDRESS, GPIO_SCL_LOW); |
| if (control & GPIO_I2C3_SCL) |
| write32((uint32_t *)GPIO_I2C3_ADDRESS, GPIO_SCL_LOW); |
| |
| read32((uint32_t *)GPIO_I2C3_ADDRESS); /* Flush posted write */ |
| udelay(4); /* 4usec gets 85KHz for 1 pin, 70KHz for 4 pins */ |
| |
| if (control & GPIO_I2C2_SCL) |
| write32((uint32_t *)GPIO_I2C2_ADDRESS, GPIO_SCL_HIGH); |
| if (control & GPIO_I2C3_SCL) |
| write32((uint32_t *)GPIO_I2C3_ADDRESS, GPIO_SCL_HIGH); |
| |
| read32((uint32_t *)GPIO_I2C3_ADDRESS); /* Flush posted write */ |
| udelay(4); |
| } |
| |
| /* Restore I2C pins. */ |
| for (i = 0; i < saved_pins_count; i++) |
| restore_i2c_pin_registers(i2c_2_gpi[i].gpio, &save_table[i]); |
| } |