| chip soc/intel/cannonlake |
| # FSP configuration |
| |
| register "SataMode" = "0" # AHCI |
| register "SataSalpSupport" = "0" |
| register "satapwroptimize" = "1" |
| register "SataPortsDevSlp[1]" = "1" # PCH_M2_SATA_DEVSLP1 |
| |
| register "SataPortsEnable[0]" = "1" |
| register "SataPortsEnable[1]" = "1" # depends on SATAXPCIE1 |
| register "SataPortsEnable[2]" = "0" # Not used for SATA |
| register "SataPortsEnable[3]" = "0" # Not used for SATA |
| register "SataPortsEnable[4]" = "1" |
| register "SataPortsEnable[5]" = "1" |
| register "SataPortsEnable[6]" = "1" |
| register "SataPortsEnable[7]" = "1" |
| |
| register "SataPortsHotPlug[0]" = "1" |
| register "SataPortsHotPlug[1]" = "1" |
| register "SataPortsHotPlug[2]" = "0" |
| register "SataPortsHotPlug[3]" = "0" |
| register "SataPortsHotPlug[4]" = "1" |
| register "SataPortsHotPlug[5]" = "1" |
| register "SataPortsHotPlug[6]" = "1" |
| register "SataPortsHotPlug[7]" = "1" |
| |
| register "PchHdaDspEnable" = "0" |
| register "PchHdaAudioLinkHda" = "1" |
| |
| # Controls the CLKREQ, not the output directly. |
| # Depends on the CLKREQ to CLK gen mapping below |
| register "PcieClkSrcUsage[0]" = "PCIE_CLK_FREE" # BMC, PCIe Slot1, Slot2, Slot4, Slot6 |
| register "PcieClkSrcUsage[1]" = "PCIE_CLK_FREE" # PHY3 |
| register "PcieClkSrcUsage[2]" = "PCIE_CLK_NOTUSED" |
| register "PcieClkSrcUsage[3]" = "PCIE_CLK_NOTUSED" |
| register "PcieClkSrcUsage[4]" = "PCIE_CLK_FREE" # RP9 M2 Slot M x4 |
| register "PcieClkSrcUsage[5]" = "PCIE_CLK_FREE" # RP16 M2 Slot E x1 |
| register "PcieClkSrcUsage[6]" = "PCIE_CLK_NOTUSED" |
| register "PcieClkSrcUsage[7]" = "PCIE_CLK_NOTUSED" |
| register "PcieClkSrcUsage[8]" = "PCIE_CLK_NOTUSED" |
| register "PcieClkSrcUsage[9]" = "PCIE_CLK_NOTUSED" |
| register "PcieClkSrcUsage[10]" = "PCIE_CLK_NOTUSED" |
| register "PcieClkSrcUsage[11]" = "PCIE_CLK_NOTUSED" |
| register "PcieClkSrcUsage[12]" = "PCIE_CLK_NOTUSED" |
| register "PcieClkSrcUsage[13]" = "PCIE_CLK_FREE" # PHY 0, PHY 1, PHY 2, PHY 4 |
| register "PcieClkSrcUsage[14]" = "PCIE_CLK_FREE" # PB |
| register "PcieClkSrcUsage[15]" = "PCIE_CLK_FREE" # PCIe Slot3 |
| |
| # Only map M2 CLKREQ to CLK gen |
| register "PcieClkSrcClkReq[4]" = "4" # M2_M_CLK_REQ_n |
| register "PcieClkSrcClkReq[5]" = "5" # M2_E_CLK_REQ_n |
| |
| # USB OC5-7: not connected |
| register "usb2_ports" = "{ |
| |
| #define HERMES_USB2_CONFIG(pin) { \ |
| .enable = 1, \ |
| .ocpin = (pin), \ |
| .tx_bias = USB2_BIAS_0MV, \ |
| .tx_emp_enable = USB2_DE_EMP_ON_PRE_EMP_ON, \ |
| .pre_emp_bias = USB2_BIAS_28P15MV, \ |
| .pre_emp_bit = USB2_FULL_BIT_PRE_EMP, \ |
| } |
| [0] = HERMES_USB2_CONFIG(OC0), /* USB3 rear panel 1 */ |
| [1] = HERMES_USB2_CONFIG(OC0), |
| [2] = HERMES_USB2_CONFIG(OC1), /* USB3 rear panel 2 */ |
| [3] = HERMES_USB2_CONFIG(OC1), |
| [4] = HERMES_USB2_CONFIG(OC2), /* USB3 internal header CN_USB3_HDR */ |
| [5] = HERMES_USB2_CONFIG(OC2), |
| [6] = HERMES_USB2_CONFIG(OC3), /* USB2 internal header USB2_HDR1 */ |
| [7] = HERMES_USB2_CONFIG(OC3), |
| [8] = HERMES_USB2_CONFIG(OC4), /* USB2 internal header USB2_HDR1 */ |
| [9] = HERMES_USB2_CONFIG(OC4), |
| [10] = HERMES_USB2_CONFIG(OC_SKIP), /* BMC */ |
| [11] = USB2_PORT_EMPTY, |
| [12] = HERMES_USB2_CONFIG(OC_SKIP), /* piggy-back */ |
| [13] = HERMES_USB2_CONFIG(OC_SKIP), /* M.2 key E */ |
| }" |
| |
| # USB Config 2.0/3.0 |
| # Enumeration starts at 0 |
| # USB 3.0 |
| # USB OC0: RP1 |
| register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC0)" |
| |
| # USB OC1: RP2 |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC1)" |
| register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC1)" |
| |
| # USB OC2: Internal Header CN_USB3_HDR |
| register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC2)" |
| register "usb3_ports[5]" = "USB3_PORT_DEFAULT(OC2)" |
| |
| # Thermal |
| register "tcc_offset" = "1" # TCC of 99C |
| |
| # Disable S0ix |
| register "s0ix_enable" = "0" |
| |
| # Enable Turbo |
| register "eist_enable" = "1" |
| |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| }" |
| |
| # VR Power Delivery Design |
| register "VrPowerDeliveryDesign" = "0x12" |
| |
| register "SerialIoDevMode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C1] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoDisabled, |
| [PchSerialIoIndexSPI0] = PchSerialIoPci, |
| [PchSerialIoIndexSPI1] = PchSerialIoDisabled, |
| [PchSerialIoIndexUART0] = PchSerialIoPci, |
| [PchSerialIoIndexUART1] = PchSerialIoPci, |
| [PchSerialIoIndexUART2] = PchSerialIoPci, |
| }" |
| |
| register "DisableHeciRetry" = "1" |
| |
| device cpu_cluster 0 on |
| device lapic 0 on end |
| end |
| |
| device domain 0 on |
| device pci 00.0 on end # Host Bridge |
| device pci 01.0 on # PEG x8 / Slot 2 |
| smbios_slot_desc "SlotTypePciExpressGen3X16" "SlotLengthOther" "SLOT2" "SlotDataBusWidth8X" |
| end |
| device pci 01.1 on # PEG x4 or x8 / Slot 6 |
| smbios_slot_desc "SlotTypePciExpressGen3X16" "SlotLengthOther" "SLOT6" "SlotDataBusWidth4X" |
| end |
| device pci 01.2 on # PEG x4 or disabled / Slot 4 |
| smbios_slot_desc "SlotTypePciExpressGen3X16" "SlotLengthOther" "SLOT4" "SlotDataBusWidth4X" |
| end |
| device pci 02.0 on end # Integrated Graphics Device |
| device pci 04.0 on end # SA Thermal device |
| device pci 08.0 on end # Gaussian Mixture |
| device pci 12.0 on end # Thermal Subsystem |
| device pci 14.0 on end # USB xHCI |
| device pci 14.1 off end # USB xDCI (OTG) |
| device pci 14.2 on end # RAM controller |
| device pci 14.3 on |
| chip drivers/wifi/generic |
| register "wake" = "PME_B0_EN_BIT" |
| device generic 0 on end |
| end |
| end # CNVi wifi |
| device pci 14.5 off end # SDCard |
| device pci 16.0 on end # Management Engine Interface 1 |
| device pci 16.1 on end # Management Engine Interface 2 |
| device pci 16.4 off end # Management Engine Interface 3 |
| device pci 17.0 on end # SATA |
| # This device does not have any function on CNP-H, but it needs |
| # to be here so that the resource allocator is aware of UART 2. |
| device pci 19.0 hidden end |
| chip soc/intel/common/block/uart |
| device pci 19.2 hidden |
| register "devid" = "PCI_DEVICE_ID_INTEL_CNP_H_UART2" |
| end # UART #2, in ACPI mode |
| end |
| device pci 1b.4 on # PCIe root port 21 (Slot 1) |
| smbios_slot_desc "SlotTypePciExpressGen3X16" "SlotLengthOther" "SLOT1" "SlotDataBusWidth4X" |
| register "PcieRpEnable[20]" = "1" |
| register "PcieRpLtrEnable[20]" = "1" |
| register "PcieRpSlotImplemented[20]" = "1" |
| register "PcieRpMaxPayload[20]" = "RpMaxPayload_256" |
| register "PcieRpAdvancedErrorReporting[20]" = "1" |
| register "PcieRpAspm[20]" = "AspmDisabled" |
| end |
| device pci 1c.0 on # PCIe root port 1 (Slot 3) |
| smbios_slot_desc "SlotTypePciExpressGen3X16" "SlotLengthOther" "SLOT3" "SlotDataBusWidth4X" |
| register "PcieRpEnable[0]" = "1" |
| register "PcieRpLtrEnable[0]" = "1" |
| register "PcieRpSlotImplemented[0]" = "1" |
| register "PcieRpMaxPayload[0]" = "RpMaxPayload_256" |
| register "PcieRpAdvancedErrorReporting[0]" = "1" |
| register "PcieRpAspm[0]" = "AspmDisabled" |
| end |
| device pci 1c.4 on # PCIe root port 5 (PHY 3) |
| register "PcieRpEnable[4]" = "1" |
| end |
| device pci 1c.5 on # PCIe root port 6 (PHY 4) |
| register "PcieRpEnable[5]" = "1" |
| end |
| device pci 1c.6 on # PCIe root port 7 (PHY 2) |
| register "PcieRpEnable[6]" = "1" |
| end |
| device pci 1c.7 on # PCIe root port 8 (PHY 1) |
| register "PcieRpEnable[7]" = "1" |
| end |
| device pci 1d.0 on # PCIe root port 9 (M2 M) |
| smbios_slot_desc "SlotTypePciExpressGen3X16" "SlotLengthOther" "M2 M" "SlotDataBusWidth4X" |
| register "PcieRpEnable[8]" = "1" |
| register "PcieRpSlotImplemented[8]" = "1" |
| end |
| device pci 1d.5 on # PCIe root port 14 (PHY 0) |
| register "PcieRpEnable[13]" = "1" |
| end |
| device pci 1d.6 on # PCIe root port 15 (BMC) |
| device pci 00.0 on # Aspeed PCI Bridge |
| device pci 00.0 on end # Aspeed 2500 VGA |
| end |
| register "PcieRpEnable[14]" = "1" |
| register "PcieRpSlotImplemented[14]" = "1" |
| end |
| device pci 1d.7 on # PCIe root port 16 (M.2 E/CNVi) |
| # Disabled when CNVi is present |
| register "PcieRpEnable[15]" = "1" |
| register "PcieRpSlotImplemented[15]" = "1" |
| end |
| device pci 1e.0 on end # UART #0 |
| device pci 1e.1 on end # UART #1 |
| device pci 1e.2 off end # GSPI #0 |
| device pci 1e.3 off end # GSPI #1 |
| device pci 1f.0 on # LPC Interface |
| chip drivers/pc80/tpm |
| device pnp 0c31.0 on end |
| end |
| # AST2500, but not enabled to decode LPC cycles |
| end |
| device pci 1f.1 on end # P2SB |
| device pci 1f.2 hidden end # Power Management Controller |
| device pci 1f.3 on end # Intel HDA |
| device pci 1f.4 on end # SMBus |
| device pci 1f.5 on end # PCH SPI |
| end |
| end |