| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <console/console.h> |
| #include <device/azalia_device.h> |
| #include <device/mmio.h> |
| #include <delay.h> |
| |
| #include "hda_verb.h" |
| |
| int hda_codec_detect(u8 *base) |
| { |
| u8 reg8; |
| |
| /* Set Bit 0 to 1 to exit reset state (BAR + 0x8)[0] */ |
| if (azalia_exit_reset(base) < 0) |
| goto no_codec; |
| |
| /* Write back the value once reset bit is set. */ |
| write16(base + HDA_GCAP_REG, read16(base + HDA_GCAP_REG)); |
| |
| /* Clear the "State Change Status Register" STATESTS bits |
| * for each of the "SDIN Stat Change Status Flag" |
| */ |
| write8(base + HDA_STATESTS_REG, 0xf); |
| |
| /* Turn off the link and poll RESET# bit until it reads back as 0 */ |
| if (azalia_enter_reset(base) < 0) |
| goto no_codec; |
| |
| /* Turn on the link and poll RESET# bit until it reads back as 1 */ |
| if (azalia_exit_reset(base) < 0) |
| goto no_codec; |
| |
| /* Read in Codec location (BAR + 0xe)[2..0]*/ |
| reg8 = read8(base + HDA_STATESTS_REG); |
| reg8 &= 0x0f; |
| if (!reg8) |
| goto no_codec; |
| |
| return reg8; |
| |
| no_codec: |
| /* Codec not found, put HDA back in reset */ |
| azalia_enter_reset(base); |
| printk(BIOS_DEBUG, "HDA: No codec!\n"); |
| return 0; |
| } |
| |
| /* |
| * Wait 50usec for the codec to indicate it is ready. |
| * No response would imply that the codec is non-operative. |
| */ |
| static int hda_wait_for_ready(u8 *base) |
| { |
| /* Use a 50 usec timeout - the Linux kernel uses the same duration */ |
| int timeout = 50; |
| |
| while (timeout--) { |
| u32 reg32 = read32(base + HDA_ICII_REG); |
| if (!(reg32 & HDA_ICII_BUSY)) |
| return 0; |
| udelay(1); |
| } |
| |
| return -1; |
| } |
| |
| /* |
| * Wait 50usec for the codec to indicate that it accepted the previous command. |
| * No response would imply that the code is non-operative. |
| */ |
| static int hda_wait_for_valid(u8 *base) |
| { |
| u32 reg32; |
| /* Use a 50 usec timeout - the Linux kernel uses the same duration */ |
| int timeout = 50; |
| |
| /* Send the verb to the codec */ |
| reg32 = read32(base + HDA_ICII_REG); |
| reg32 |= HDA_ICII_BUSY | HDA_ICII_VALID; |
| write32(base + HDA_ICII_REG, reg32); |
| |
| while (timeout--) { |
| reg32 = read32(base + HDA_ICII_REG); |
| if ((reg32 & (HDA_ICII_VALID | HDA_ICII_BUSY)) == HDA_ICII_VALID) |
| return 0; |
| udelay(1); |
| } |
| |
| return -1; |
| } |
| |
| int hda_codec_write(u8 *base, u32 size, const u32 *data) |
| { |
| int i; |
| |
| for (i = 0; i < size; i++) { |
| if (hda_wait_for_ready(base) < 0) |
| return -1; |
| |
| write32(base + HDA_IC_REG, data[i]); |
| |
| if (hda_wait_for_valid(base) < 0) |
| return -1; |
| } |
| |
| return 0; |
| } |
| |
| int hda_codec_init(u8 *base, int addr, int verb_size, const u32 *verb_data) |
| { |
| const u32 *verb; |
| u32 reg32, size; |
| int rc; |
| |
| printk(BIOS_DEBUG, "HDA: Initializing codec #%d\n", addr); |
| |
| if (!verb_size || !verb_data) { |
| printk(BIOS_DEBUG, "HDA: No verb list!\n"); |
| return -1; |
| } |
| |
| /* 1 */ |
| if (hda_wait_for_ready(base) < 0) { |
| printk(BIOS_DEBUG, " codec not ready.\n"); |
| return -1; |
| } |
| |
| reg32 = (addr << 28) | 0x000f0000; |
| write32(base + HDA_IC_REG, reg32); |
| |
| if (hda_wait_for_valid(base) < 0) { |
| printk(BIOS_DEBUG, " codec not valid.\n"); |
| return -1; |
| } |
| |
| /* 2 */ |
| reg32 = read32(base + HDA_IR_REG); |
| printk(BIOS_DEBUG, "HDA: codec viddid: %08x\n", reg32); |
| |
| size = azalia_find_verb(verb_data, verb_size, reg32, &verb); |
| if (!size) { |
| printk(BIOS_DEBUG, "HDA: No verb table entry found\n"); |
| return -1; |
| } |
| |
| /* 3 */ |
| rc = hda_codec_write(base, size, verb); |
| |
| if (rc < 0) |
| printk(BIOS_DEBUG, "HDA: verb not loaded\n"); |
| else |
| printk(BIOS_DEBUG, "HDA: verb loaded.\n"); |
| |
| return rc; |
| } |