| chip soc/intel/apollolake |
| |
| register "pcie_rp_clkreq_pin[2]" = "3" # wifi/bt |
| # Disable unused clkreq of PCIe root ports |
| register "pcie_rp_clkreq_pin[0]" = "CLKREQ_DISABLED" |
| register "pcie_rp_clkreq_pin[1]" = "CLKREQ_DISABLED" |
| register "pcie_rp_clkreq_pin[3]" = "CLKREQ_DISABLED" |
| register "pcie_rp_clkreq_pin[4]" = "CLKREQ_DISABLED" |
| register "pcie_rp_clkreq_pin[5]" = "CLKREQ_DISABLED" |
| |
| # Set de-emphasis to disabled for PCIE WiFI (Thunderpeak) |
| # as it is required for detection |
| register "pcie_rp_deemphasis_enable[2]" = "0" |
| # Set de-emphasis to default (enabled) for remaining ports |
| register "pcie_rp_deemphasis_enable[0]" = "1" |
| register "pcie_rp_deemphasis_enable[1]" = "1" |
| register "pcie_rp_deemphasis_enable[3]" = "1" |
| register "pcie_rp_deemphasis_enable[4]" = "1" |
| register "pcie_rp_deemphasis_enable[5]" = "1" |
| |
| # GPIO for PERST_0 (WLAN_PE_RST) |
| register "prt0_gpio" = "GPIO_164" |
| |
| # GPE configuration |
| # Note that GPE events called out in ASL code rely on this |
| # route, i.e., if this route changes then the affected GPE |
| # offset bits also need to be changed. This sets the PMC register |
| # GPE_CFG fields. |
| # DW1 is used by: |
| # - GPIO_63 - H1_PCH_INT_ODL |
| # DW2 is used by: |
| # - GPIO_141 - EC_PCH_WAKE_ODL |
| # - GPIO_142 - TRACKPAD_INT2_1V8_ODL |
| # - GPIO_144 - PEN_EJECT_ODL |
| # DW3 is used by: |
| # - GPIO_117 - LTE_WAKE_ODL |
| # - GPIO_119 - WLAN_PCIE_WAKE_ODL |
| register "gpe0_dw1" = "PMC_GPE_NW_63_32" |
| register "gpe0_dw2" = "PMC_GPE_N_95_64" |
| register "gpe0_dw3" = "PMC_GPE_N_63_32" |
| |
| # PL1 override 10 W: Due to error in the energy calculation for |
| # current VR solution. Experiments show that SoC TDP max (6W) can |
| # be reached when RAPL PL1 is set to 10W. |
| # Set RAPL PL2 to 15W. |
| register "power_limits_config" = "{ |
| .tdp_pl1_override = 10, |
| .tdp_pl2_override = 15, |
| }" |
| |
| # Minimum SLP S3 assertion width 28ms. |
| register "slp_s3_assertion_width_usecs" = "28000" |
| |
| # Enable lpss s0ix |
| register "lpss_s0ix_enable" = "1" |
| |
| # Enable DPTF |
| register "dptf_enable" = "1" |
| |
| # Enable Audio Clock and Power gating |
| register "hdaudio_clk_gate_enable" = "1" |
| register "hdaudio_pwr_gate_enable" = "1" |
| register "hdaudio_bios_config_lockdown" = "1" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| GSPI0 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| | before memory is up | |
| #| I2C0 | Digitizer | |
| #| I2C5 | Audio | |
| #| I2C6 | Trackpad | |
| #| I2C7 | Touchscreen | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .gspi[0] = { |
| .speed_mhz = 1, |
| .early_init = 1, |
| }, |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 152, |
| .fall_time_ns = 30, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 104, |
| .fall_time_ns = 52, |
| }, |
| .i2c[6] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 114, |
| .fall_time_ns = 164, |
| .data_hold_time_ns = 350, |
| }, |
| .i2c[7] = { |
| .speed = I2C_SPEED_FAST, |
| .rise_time_ns = 76, |
| .fall_time_ns = 164, |
| }, |
| }" |
| |
| register "pnp_settings" = "PNP_PERF_POWER" |
| |
| device domain 0 on |
| device pci 00.0 on end # - Host Bridge |
| device pci 00.1 on end # - DPTF |
| device pci 00.2 off end # - NPK |
| device pci 02.0 on # - Gen |
| register "gfx" = "GMA_DEFAULT_PANEL(0)" |
| end |
| device pci 03.0 on end # - Gaussian Mixture Model (GMM) |
| device pci 0c.0 on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0A_CNVI_PME_STS" |
| device generic 0 on end |
| end |
| end # - CNVi |
| device pci 0d.0 on end # - P2SB |
| device pci 0d.1 on end # - PMC |
| device pci 0d.2 on end # - Fast SPI |
| device pci 0d.3 on end # - Shared SRAM |
| device pci 0e.0 on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98357A"" |
| register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_91)" |
| register "sdmode_delay" = "5" |
| device generic 0 on end |
| end |
| end # - Audio |
| device pci 0f.0 on end # - Heci1 |
| device pci 0f.1 on end # - Heci2 |
| device pci 0f.2 on end # - Heci3 |
| device pci 11.0 off end # - ISH |
| device pci 12.0 off end # - SATA |
| device pci 13.0 on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_DW3_11" |
| device pci 00.0 on end |
| end |
| end # - PCIe-A 0 Onboard M2 Slot(Wifi) |
| device pci 13.1 off end # - PCIe-A 1 |
| device pci 13.2 off end # - PCIe-A 2 |
| device pci 13.3 off end # - PCIe-A 3 |
| device pci 14.0 off end # - PCIe-B 0 |
| device pci 14.1 off end # - PCIe-B 1 |
| device pci 15.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Root Hub"" |
| register "type" = "UPC_TYPE_HUB" |
| device usb 0.0 on |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device usb 2.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-A Port"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device usb 2.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_109)" |
| device usb 2.2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 2.3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device usb 2.4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""SDCard"" |
| register "type" = "UPC_TYPE_EXPRESSCARD" |
| device usb 2.5 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""User Facing Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""World Facing Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device usb 2.7 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_109)" |
| device usb 2.8 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(1, 1)" |
| device usb 3.0 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Left Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(1, 2)" |
| device usb 3.1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-A Port"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "group" = "ACPI_PLD_GROUP(2, 2)" |
| device usb 3.3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""Right Type-C Port"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "group" = "ACPI_PLD_GROUP(2, 1)" |
| device usb 3.4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""SDCard"" |
| register "type" = "UPC_TYPE_EXPRESSCARD" |
| device usb 3.5 on end |
| end |
| end |
| end |
| end # - XHCI |
| device pci 15.1 on end # - XDCI |
| device pci 16.0 on end # - I2C 0 |
| device pci 16.1 off end # - I2C 1 |
| device pci 16.2 off end # - I2C 2 |
| device pci 16.3 off end # - I2C 3 |
| device pci 17.0 on end # - I2C 4 |
| device pci 17.1 on end # - I2C 5 |
| device pci 17.2 on end # - I2C 6 |
| device pci 17.3 off end # - I2C 7 |
| device pci 18.0 on end # - UART 0 |
| device pci 18.1 off end # - UART 1 |
| device pci 18.2 on end # - UART 2 |
| device pci 18.3 off end # - UART 3 |
| device pci 19.0 on |
| chip drivers/spi/acpi |
| register "hid" = "ACPI_DT_NAMESPACE_HID" |
| register "compat_string" = ""google,cr50"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_63_IRQ)" |
| device spi 0 on end |
| end |
| end # - GSPI 0 |
| device pci 19.1 off end # - SPI 1 |
| device pci 19.2 on end # - SPI 2 |
| device pci 1a.0 on end # - PWM |
| device pci 1c.0 on end # - eMMC |
| device pci 1d.0 on end # - UFS |
| device pci 1e.0 off end # - SDIO |
| device pci 1f.0 on |
| chip ec/google/chromeec |
| device pnp 0c09.0 on end |
| end |
| end # - ESPI |
| device pci 1f.1 on end # - SMBUS |
| end |
| |
| # FSP provides UPD interface to execute IPC command. PMIC has |
| # I2C_Slave_Address (31:24): 0x5E, Register_Offset (23:16): 0x43, |
| # RegOrValue (15:8): 0x2 and RegAndValue (7:0) 0xF8. |
| # The register is defined as: D[7:3] RSVD, D[2:0] PWROKDELAY. |
| # uint8 RegOrValue, RegAndValue, PmicReadReg |
| # RegOrValue = (UINT8)((PmicPmcIpcCtrl >> 8) & 0xff); |
| # RegAndValue = (UINT8)(PmicPmcIpcCtrl & 0xff); |
| # PmicReadReg &= RegAndValue; |
| # PmicReadReg |= RegOrValue; |
| # PmicReadReg value will be programmed into PMIC D[2:0] PWROKDELAY field |
| # and D[7:3] RSVD will not be impacted. |
| |
| # Configure PmicPmcIpcCtrl for PMC to program PMIC PCH_PWROK delay |
| # from 100ms to 10ms. |
| # PWROKDELAY[2:0]: 000=2.5ms, 001=5.0ms, 010=10ms, 011=15ms, 100=20ms, |
| # 101=50ms, 110=75ms, 111=100ms (default) |
| register "PmicPmcIpcCtrl" = "0x5e4302f8" |
| |
| # FSP UPD to modify the Integrated Filter (IF) value |
| # Set it to default value: 0x12 |
| register "ModPhyIfValue" = "0x12" |
| end |