| fw_config |
| field DB_USB 0 1 |
| option DB_NONE 0 |
| option DB_1C_1A 1 |
| option DB_1C_LTE 2 |
| option DB_1A_HDMI 3 |
| end |
| field WFC 2 3 |
| option WFC_ABSENT 0 |
| option WFC_MIPI_OVTI5675 1 |
| option WFC_MIPI_OVTI8856 2 |
| end |
| field STYLUS 4 |
| option STYLUS_ABSENT 0 |
| option STYLUS_PRESENT 1 |
| end |
| field SD_CARD 5 |
| option SD_PRESENT 0 |
| option SD_ABSENT 1 |
| end |
| field AMP 6 7 |
| option AMP_MX98360A 0 |
| option AMP_ALC5650 1 |
| end |
| field THERMAL_SOLUTION 10 12 |
| option THERMAL_SOLUTION_6W 0 |
| option THERMAL_SOLUTION_15W 1 |
| end |
| field WIFI_SAR_ID 13 15 |
| option ID_0 0 |
| end |
| field CODEC 32 33 |
| option CODEC_ALC5682I_VS 0 |
| option CODEC_NAU8825 1 |
| option CODEC_ALC5650 2 |
| end |
| field TS_SOURCE 38 41 |
| option TS_UNPROVISIONED 0 |
| option TS_GTCH7503 1 |
| end |
| end |
| |
| chip soc/intel/alderlake |
| register "sagv" = "SaGv_Enabled" |
| |
| # EMMC Tx CMD Delay |
| # Refer to EDS-Vol2-42.3.7. |
| # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" |
| |
| # EMMC TX DATA Delay 1 |
| # Refer to EDS-Vol2-42.3.8. |
| # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. |
| # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" |
| |
| # EMMC TX DATA Delay 2 |
| # Refer to EDS-Vol2-42.3.9. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. |
| # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828" |
| |
| # EMMC RX CMD/DATA Delay 1 |
| # Refer to EDS-Vol2-42.3.10. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. |
| # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F3C" |
| |
| # EMMC RX CMD/DATA Delay 2 |
| # Refer to EDS-Vol2-42.3.12. |
| # [17:16] stands for Rx Clock before Output Buffer, |
| # 00: Rx clock after output buffer, |
| # 01: Rx clock before output buffer, |
| # 10: Automatic selection based on working mode. |
| # 11: Reserved |
| # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10023" |
| |
| # EMMC Rx Strobe Delay |
| # Refer to EDS-Vol2-42.3.11. |
| # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. |
| # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x11515" |
| |
| # SOC Aux orientation override: |
| # This is a bitfield that corresponds to up to 4 TCSS ports. |
| # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2. |
| # TcssAuxOri = 0101b |
| # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports |
| # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the |
| # motherboard to USBC connector |
| register "tcss_aux_ori" = "5" |
| |
| register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" |
| register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" |
| |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN |
| |
| # Configure external V1P05/Vnn/VnnSx Rails |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 1, |
| .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0, |
| .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL, |
| .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE, |
| .v1p05_voltage_mv = 1050, |
| .vnn_voltage_mv = 780, |
| .vnn_sx_voltage_mv = 1050, |
| .v1p05_icc_max_ma = 500, |
| .vnn_icc_max_ma = 500, |
| }" |
| |
| # Enable the Cnvi BT Audio Offload |
| register "cnvi_bt_audio_offload" = "1" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| I2C0 | TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C1 | Touchscreen | |
| #| I2C2 | Sub-board(PSensor)/WCAM | |
| #| I2C3 | Audio | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST_PLUS, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .scl_lcnt = 55, |
| .scl_hcnt = 30, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 30, |
| } |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 40, |
| } |
| }, |
| }" |
| |
| |
| register "power_limits_config[ADL_N_041_6W_CORE]" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 25, |
| .tdp_pl4 = 78, |
| }" |
| |
| register "power_limits_config[ADL_N_021_6W_CORE]" = "{ |
| .tdp_pl1_override = 6, |
| .tdp_pl2_override = 25, |
| .tdp_pl4 = 78, |
| }" |
| |
| device domain 0 on |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""Memory"" |
| register "options.tsr[1].desc" = ""Charger"" |
| register "options.tsr[2].desc" = ""Ambient"" |
| |
| # TODO: below values are initial reference values only |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), |
| [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 5500, |
| .max_power = 6000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 28 * MSECS_PER_SEC, |
| .granularity = 200 |
| }, |
| .pl2 = { |
| .min_power = 25000, |
| .max_power = 25000, |
| .time_window_min = 1, |
| .time_window_max = 1, |
| .granularity = 1000 |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| device generic 0 on |
| probe THERMAL_SOLUTION THERMAL_SOLUTION_6W |
| end |
| end |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""Memory"" |
| register "options.tsr[1].desc" = ""Charger"" |
| register "options.tsr[2].desc" = ""Ambient"" |
| |
| # TODO: below values are initial reference values only |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), |
| [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 15000, |
| .max_power = 15000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 28 * MSECS_PER_SEC, |
| .granularity = 125 |
| }, |
| .pl2 = { |
| .min_power = 35000, |
| .max_power = 35000, |
| .time_window_min = 1, |
| .time_window_max = 1, |
| .granularity = 1000 |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| device generic 1 on |
| probe THERMAL_SOLUTION THERMAL_SOLUTION_15W |
| end |
| end |
| end |
| device ref ipu on |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "0x50000" |
| register "acpi_name" = ""IPU0"" |
| register "device_type" = "INTEL_ACPI_CAMERA_CIO2" |
| |
| register "cio2_num_ports" = "1" |
| register "cio2_lanes_used" = "{2}" # 2 CSI Camera lanes are used |
| register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0"" |
| register "cio2_prt[0]" = "1" |
| device generic 0 on end |
| end |
| probe WFC WFC_MIPI_OVTI5675 |
| probe WFC WFC_MIPI_OVTI8856 |
| end |
| |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "enable_cnvi_ddr_rfim" = "true" |
| device generic 0 on end |
| end |
| end |
| |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GTCH7502"" |
| register "generic.desc" = ""G2 Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "120" |
| register "generic.reset_off_delay_ms" = "3" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "12" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x40 on |
| probe TS_SOURCE TS_UNPROVISIONED |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GTCH7503"" |
| register "generic.desc" = ""G2 Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "120" |
| register "generic.reset_off_delay_ms" = "3" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "12" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x40 on |
| probe TS_SOURCE TS_GTCH7503 |
| end |
| end |
| chip drivers/generic/gpio_keys |
| register "name" = ""PENH"" |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F13)" |
| register "key.wake_gpe" = "GPE0_DW2_15" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" |
| register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" |
| register "key.dev_name" = ""EJCT"" |
| register "key.linux_code" = "SW_PEN_INSERTED" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""pen_eject"" |
| device generic 0 on |
| probe STYLUS STYLUS_PRESENT |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9004"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_delay_ms" = "280" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on |
| probe TS_SOURCE TS_UNPROVISIONED |
| end |
| end |
| end |
| device ref i2c2 on |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI5675"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 5675 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| |
| register "ssdb.lanes_used" = "2" |
| register "ssdb.link_used" = "1" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "1" |
| register "link_freq[0]" = "DEFAULT_LINK_FREQ" |
| register "remote_name" = ""IPU0"" |
| |
| register "has_power_resource" = "1" |
| register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" |
| |
| #Controls |
| register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" |
| register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1800_PP1200_WCAM_X |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 36 on |
| probe WFC WFC_MIPI_OVTI5675 |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = ""OVTI8856"" |
| register "acpi_uid" = "0" |
| register "acpi_name" = ""CAM0"" |
| register "chip_name" = ""Ov 8856 Camera"" |
| register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" |
| register "has_power_resource" = "1" |
| register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" |
| |
| register "ssdb.lanes_used" = "2" |
| register "ssdb.link_used" = "1" |
| register "ssdb.vcm_type" = "0x0C" |
| register "vcm_name" = ""VCM0"" |
| register "num_freq_entries" = "2" |
| register "link_freq[0]" = "720000000" |
| register "link_freq[1]" = "360000000" |
| register "remote_name" = ""IPU0"" |
| |
| #Controls |
| register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" |
| register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" |
| |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X |
| register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1800_PP1200_WCAM_X |
| register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L |
| |
| #_ON |
| register "on_seq.ops_cnt" = "5" |
| register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" |
| register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" |
| register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" |
| register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "4" |
| register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" |
| register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" |
| register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" |
| register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 10 on |
| probe WFC WFC_MIPI_OVTI8856 |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_uid" = "3" |
| register "acpi_name" = ""VCM0"" |
| register "chip_name" = ""DW AF DAC"" |
| register "device_type" = "INTEL_ACPI_CAMERA_VCM" |
| |
| register "vcm_compat" = ""dongwoon,dw9714"" |
| register "has_power_resource" = "1" |
| register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" |
| |
| #Controls |
| register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X |
| |
| #_ON |
| register "on_seq.ops_cnt" = "1" |
| register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" |
| |
| #_OFF |
| register "off_seq.ops_cnt" = "1" |
| register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" |
| |
| device i2c 0C on |
| probe WFC WFC_MIPI_OVTI5675 |
| probe WFC WFC_MIPI_OVTI8856 |
| end |
| end |
| chip drivers/intel/mipi_camera |
| register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" |
| register "acpi_uid" = "1" |
| register "acpi_name" = ""NVM0"" |
| register "chip_name" = ""GT24C08"" |
| register "device_type" = "INTEL_ACPI_CAMERA_NVM" |
| |
| register "nvm_size" = "0x2000" |
| register "nvm_pagesize" = "1" |
| register "nvm_readonly" = "1" |
| register "nvm_width" = "0x10" |
| register "nvm_compat" = ""atmel,24c08"" |
| |
| device i2c 50 on |
| probe WFC WFC_MIPI_OVTI5675 |
| probe WFC WFC_MIPI_OVTI8856 |
| end |
| end |
| end |
| device ref i2c3 on |
| chip drivers/i2c/nau8825 |
| register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)" |
| register "jkdet_enable" = "1" |
| register "jkdet_pull_enable" = "0" |
| register "jkdet_polarity" = "1" # ActiveLow |
| register "vref_impedance" = "2" # 125kOhm |
| register "micbias_voltage" = "6" # 2.754 |
| register "sar_threshold_num" = "4" |
| register "sar_threshold[0]" = "0x0c" |
| register "sar_threshold[1]" = "0x1c" |
| register "sar_threshold[2]" = "0x38" |
| register "sar_threshold[3]" = "0x60" |
| register "sar_hysteresis" = "1" |
| register "sar_voltage" = "0" # VDDA |
| register "sar_compare_time" = "0" # 500ns |
| register "sar_sampling_time" = "0" # 2us |
| register "short_key_debounce" = "2" # 100ms |
| register "jack_insert_debounce" = "7" # 512ms |
| register "jack_eject_debounce" = "7" # 512ms |
| device i2c 1a on |
| probe CODEC CODEC_NAU8825 |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on |
| probe CODEC CODEC_ALC5682I_VS |
| end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC5650"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5650"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-mode"" |
| register "property_list[0].integer" = "2" |
| device i2c 1a on |
| probe CODEC CODEC_ALC5650 |
| end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "wake" = "GPE0_DW2_14" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""SYNA0000"" |
| register "generic.cid" = ""ACPI0C50"" |
| register "generic.desc" = ""Synaptics Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 0x2c on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PIXA2303"" |
| register "generic.desc" = ""PIXA Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 0x68 on end |
| end |
| end |
| device ref hda on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98360A"" |
| register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "sdmode_delay" = "5" |
| device generic 0 on |
| probe AMP AMP_MX98360A |
| end |
| end |
| chip drivers/sof |
| register "spkr_tplg" = "max98360a" |
| register "jack_tplg" = "rt5682" |
| register "mic_tplg" = "_2ch_pdm0" |
| device generic 0 on |
| probe CODEC CODEC_ALC5682I_VS |
| end |
| end |
| chip drivers/sof |
| register "spkr_tplg" = "max98360a" |
| register "jack_tplg" = "nau8825" |
| register "mic_tplg" = "_2ch_pdm0" |
| device generic 0 on |
| probe CODEC CODEC_NAU8825 |
| end |
| end |
| end |
| device ref pcie_rp7 on |
| # Enable SD Card PCIe 7 using clk 3 |
| register "pch_pcie_rp[PCH_RP(7)]" = "{ |
| .clk_src = 3, |
| .clk_req = 3, |
| .flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)" |
| register "srcclk_pin" = "3" |
| device generic 0 on end |
| end |
| probe SD_CARD SD_PRESENT |
| end |
| device ref pcie_rp9 on |
| # Enable NVMe SSD PCIe 9-12 using clk_src1 and clk_req2 mapping to hardware |
| # design.Due to inconsistency between PMC firmware and FSP, we need to set |
| # clk_src to clk_req number, not same as hardware mapping in coreboot.Then |
| # swap correct setting to clk_src=1,clk_req=2 in mFIT. |
| register "pch_pcie_rp[PCH_RP(9)]" = "{ |
| .clk_src = 2, |
| .clk_req = 2, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 1 alias conn1 on |
| probe DB_USB DB_1C_1A |
| probe DB_USB DB_1C_LTE |
| end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port2 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port2 on |
| probe DB_USB DB_1C_1A |
| probe DB_USB DB_1C_LTE |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb2_port4 on |
| probe DB_USB DB_1C_1A |
| probe DB_USB DB_1A_HDMI |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port4 on |
| probe DB_USB DB_1C_LTE |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb3_port2 on |
| probe DB_USB DB_1C_1A |
| probe DB_USB DB_1A_HDMI |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb3_port2 on |
| probe DB_USB DB_1C_LTE |
| end |
| end |
| end |
| end |
| end |
| end |
| end |