| chip northbridge/intel/sandybridge |
| # IGD Displays |
| register "gfx" = "GMA_STATIC_DISPLAYS(1)" |
| |
| # Enable DisplayPort Hotplug with 6ms pulse |
| register "gpu_dp_d_hotplug" = "0x06" |
| |
| # Enable Panel as LVDS and configure power delays |
| register "gpu_panel_port_select" = "PANEL_PORT_LVDS" |
| register "gpu_panel_power_cycle_delay" = "5" |
| register "gpu_panel_power_up_delay" = "300" # T1+T2: 30ms |
| register "gpu_panel_power_down_delay" = "300" # T5+T6: 30ms |
| register "gpu_panel_power_backlight_on_delay" = "2000" # T3: 200ms |
| register "gpu_panel_power_backlight_off_delay" = "2000" # T4: 200ms |
| register "gpu_cpu_backlight" = "0x1155" |
| register "gpu_pch_backlight" = "0x06100610" |
| |
| register "spd_addresses" = "{0x50, 0, 0x51, 0}" |
| register "ec_present" = "1" # I have an embedded controller |
| register "max_mem_clock_mhz" = "666" # So DDR3 freq = 1333 |
| |
| register "usb_port_config" = "{ |
| { 1, 0, 0x0040 }, |
| { 1, 1, 0x0080 }, |
| { 1, 3, 0x0080 }, |
| { 1, 3, 0x0080 }, |
| { 1, 0, 0x0080 }, |
| { 1, 0, 0x0080 }, |
| { 1, 2, 0x0040 }, |
| { 1, 2, 0x0040 }, |
| { 1, 6, 0x0080 }, |
| { 1, 5, 0x0080 }, |
| { 1, 6, 0x0080 }, |
| { 1, 6, 0x0080 }, |
| { 1, 7, 0x0080 }, |
| { 1, 6, 0x0080 },}" |
| |
| chip cpu/intel/model_206ax |
| # Values obtained from vendor BIOS v1.46 |
| # schematics say 33Amps for 17W TDP, 53Amps for 35W TDP |
| register "pp0_current_limit" = "98" |
| # schematics say 33Amps for GFX |
| register "pp1_current_limit" = "33" |
| register "pp0_psi[VR12_PSI1]" = "{VR12_2_PHASES, 20}" |
| register "pp0_psi[VR12_PSI2]" = "{VR12_ALL_PHASES, 5}" |
| register "pp0_psi[VR12_PSI3]" = "{VR12_ALL_PHASES, 1}" |
| register "pp1_psi[VR12_PSI1]" = "{VR12_2_PHASES, 20}" |
| register "pp1_psi[VR12_PSI2]" = "{VR12_ALL_PHASES, 5}" |
| register "pp1_psi[VR12_PSI3]" = "{VR12_ALL_PHASES, 1}" |
| device cpu_cluster 0 on end |
| end |
| device domain 0 on |
| subsystemid 0x17aa 0x21db inherit |
| |
| device ref host_bridge on end |
| device ref peg10 off end |
| device ref igd on end |
| |
| chip southbridge/intel/bd82x6x # Intel Series 6 Cougar Point PCH |
| # GPI routing |
| # 0 No effect (default) |
| # 1 SMI# (if corresponding ALT_GPI_SMI_EN bit is also set) |
| # 2 SCI (if corresponding GPIO_EN bit is also set) |
| register "alt_gp_smi_en" = "0x0000" |
| register "gpi1_routing" = "2" |
| register "gpi13_routing" = "2" |
| |
| # Enable SATA ports 0 (HDD bay) & 1 (dock) & 2 (msata) |
| register "sata_port_map" = "0x7" |
| # Set max SATA speed to 6.0 Gb/s |
| register "sata_interface_speed_support" = "0x3" |
| |
| register "gen1_dec" = "0x7c1601" |
| register "gen2_dec" = "0x0c15e1" |
| register "gen4_dec" = "0x0c06a1" |
| |
| register "pcie_hotplug_map" = "{ 0, 0, 0, 1, 0, 0, 0, 0 }" |
| |
| # Enable zero-based linear PCIe root port functions |
| register "pcie_port_coalesce" = "true" |
| |
| register "spi_uvscc" = "0x2005" |
| register "spi_lvscc" = "0x2005" |
| |
| device ref mei1 on end |
| device ref mei2 off end |
| device ref me_ide_r off end |
| device ref me_kt off end |
| device ref gbe on |
| subsystemid 0x17aa 0x21ce |
| end |
| device ref ehci2 on end |
| device ref hda on end |
| device ref pcie_rp1 off end |
| device ref pcie_rp2 on |
| smbios_slot_desc "SlotTypeM2Socket1_SD" "SlotLengthShort" |
| "WIFI" "SlotDataBusWidth1X" |
| end |
| device ref pcie_rp3 off end |
| device ref pcie_rp4 on |
| smbios_slot_desc "7" "3" "ExpressCard Slot" "8" |
| end |
| device ref pcie_rp5 on |
| chip drivers/ricoh/rce822 |
| register "sdwppol" = "1" |
| register "disable_mask" = "0x87" |
| device pci 00.0 on end |
| end |
| end |
| device ref pcie_rp6 off end |
| device ref pcie_rp7 on end # Optional XHCI controller |
| device ref pcie_rp8 off end |
| device ref ehci1 on end |
| device ref pci_bridge off end |
| device ref lpc on |
| chip ec/lenovo/pmh7 |
| device pnp ff.1 on end # dummy |
| register "backlight_enable" = "true" |
| register "dock_event_enable" = "true" |
| end |
| |
| chip drivers/pc80/tpm |
| device pnp 0c31.0 on end |
| end |
| |
| chip ec/lenovo/h8 |
| device pnp ff.2 on # dummy |
| io 0x60 = 0x62 |
| io 0x62 = 0x66 |
| io 0x64 = 0x1600 |
| io 0x66 = 0x1604 |
| end |
| |
| register "config0" = "0xa6" |
| register "config1" = "0x01" |
| register "config2" = "0xa0" |
| register "config3" = "0x60" |
| |
| register "has_keyboard_backlight" = "0" |
| |
| register "beepmask0" = "0x00" |
| register "beepmask1" = "0x86" |
| register "has_power_management_beeps" = "1" |
| register "event2_enable" = "0xff" |
| register "event3_enable" = "0xff" |
| register "event4_enable" = "0xd0" |
| register "event5_enable" = "0xfc" |
| register "event6_enable" = "0x00" |
| register "event7_enable" = "0x81" |
| register "event8_enable" = "0x7b" |
| register "event9_enable" = "0xff" |
| register "eventc_enable" = "0xff" |
| register "eventd_enable" = "0xff" |
| register "evente_enable" = "0x0d" |
| |
| # BDC detection is broken on this board: |
| # BDC shorts pin14 and pin1 |
| # BDC's connector pin14 is left floating |
| # BDC's connector pin1 is routed to SB GPIO 54 |
| register "has_bdc_detection" = "0" |
| |
| register "has_wwan_detection" = "1" |
| register "wwan_gpio_num" = "70" |
| register "wwan_gpio_lvl" = "0" |
| end |
| end |
| device ref sata1 on end |
| device ref smbus on |
| # eeprom, 8 virtual devices, same chip |
| chip drivers/i2c/at24rf08c |
| device i2c 54 on end |
| device i2c 55 on end |
| device i2c 56 on end |
| device i2c 57 on end |
| device i2c 5c on end |
| device i2c 5d on end |
| device i2c 5e on end |
| device i2c 5f on end |
| end |
| end |
| device ref sata2 off end |
| device ref thermal on end |
| end |
| end |
| end |