| fw_config |
| field DB_USB 0 1 |
| option DB_ABSENT 0 |
| option DB_1C 1 |
| end |
| field THERMAL 2 2 |
| option THERMAL_FANLESS 0 |
| option THERMAL_FAN 1 |
| end |
| field WIFI_SAR_ID 6 6 |
| option WIFI_GFP2_SAR_ID_0 0 |
| option WIFI_GFP2_SAR_ID_1 1 |
| end |
| end |
| |
| chip soc/intel/alderlake |
| register "sagv" = "SaGv_Enabled" |
| |
| # Acoustic settings |
| register "acoustic_noise_mitigation" = "1" |
| register "slow_slew_rate[VR_DOMAIN_IA]" = "SLEW_FAST_8" |
| register "slow_slew_rate[VR_DOMAIN_GT]" = "SLEW_FAST_8" |
| register "fast_pkg_c_ramp_disable[VR_DOMAIN_IA]" = "1" |
| register "fast_pkg_c_ramp_disable[VR_DOMAIN_GT]" = "1" |
| |
| # EMMC Tx CMD Delay |
| # Refer to EDS-Vol2-42.3.7. |
| # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" |
| |
| # EMMC TX DATA Delay 1 |
| # Refer to EDS-Vol2-42.3.8. |
| # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. |
| # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" |
| |
| # EMMC TX DATA Delay 2 |
| # Refer to EDS-Vol2-42.3.9. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. |
| # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C272828" |
| |
| # EMMC RX CMD/DATA Delay 1 |
| # Refer to EDS-Vol2-42.3.10. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. |
| # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C171733" |
| |
| # EMMC RX CMD/DATA Delay 2 |
| # Refer to EDS-Vol2-42.3.12. |
| # [17:16] stands for Rx Clock before Output Buffer, |
| # 00: Rx clock after output buffer, |
| # 01: Rx clock before output buffer, |
| # 10: Automatic selection based on working mode. |
| # 11: Reserved |
| # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10028" |
| |
| # EMMC Rx Strobe Delay |
| # Refer to EDS-Vol2-42.3.11. |
| # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. |
| # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x1414" |
| |
| # Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC. |
| # Bit 2 - C1 has a redriver which does SBU muxing. |
| # Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1. |
| register "tcss_aux_ori" = "1" |
| |
| register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" |
| |
| register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # UFC |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN |
| |
| # Configure external V1P05/Vnn/VnnSx Rails |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 1, |
| }" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| I2C0 | TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C1 | Touchscreen | |
| #| I2C2 | Sub-board(PSensor)/WCAM | |
| #| I2C3 | Audio | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST_PLUS, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .scl_lcnt = 56, |
| .scl_hcnt = 30, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 30, |
| } |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 158, |
| .scl_hcnt = 79, |
| .sda_hold = 40, |
| } |
| }, |
| }" |
| |
| # Power limit config |
| |
| register "power_limits_config[ADL_N_081_15W_CORE]" = "{ |
| .tdp_pl1_override = 20, |
| .tdp_pl2_override = 35, |
| .tdp_pl4 = 83, |
| }" |
| register "power_limits_config[ADL_N_041_6W_CORE]" = "{ |
| .tdp_pl1_override = 10, |
| .tdp_pl2_override = 25, |
| .tdp_pl4 = 78, |
| }" |
| |
| register "power_limits_config[ADL_N_021_6W_CORE]" = "{ |
| .tdp_pl1_override = 10, |
| .tdp_pl2_override = 25, |
| .tdp_pl4 = 78, |
| }" |
| |
| device domain 0 on |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""Memory"" |
| register "options.tsr[1].desc" = ""Charger"" |
| register "options.tsr[2].desc" = ""Ambient"" |
| |
| # TODO: below values are initial reference values only |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 65, 5000), |
| [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 65, 5000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 65, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 75, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 75, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 75, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 6000, |
| .max_power = 6000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200 |
| }, |
| .pl2 = { |
| .min_power = 25000, |
| .max_power = 25000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000 |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| register "oem_data.oem_variables" = "{ |
| [1] = 0x1 |
| }" |
| |
| device generic 0 alias dptf_policy on end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0001"" |
| register "desc" = ""ELAN Touchscreen"" |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "detect" = "1" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "reset_delay_ms" = "20" |
| register "reset_off_delay_ms" = "2" |
| register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "stop_delay_ms" = "280" |
| register "stop_off_delay_ms" = "2" |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "enable_delay_ms" = "1" |
| register "has_power_resource" = "1" |
| device i2c 10 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN2513"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "20" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_delay_ms" = "280" |
| register "generic.stop_off_delay_ms" = "2" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GTCH7503"" |
| register "generic.desc" = ""G2TOUCH Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "50" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_delay_ms" = "30" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 40 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""GDIX0000"" |
| register "generic.desc" = ""Goodix Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "20" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "180" |
| register "generic.reset_off_delay_ms" = "3" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" |
| register "generic.stop_off_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x14 on end |
| end |
| end |
| device ref i2c3 on |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "wake" = "GPE0_DW2_14" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| end |
| device ref hda on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98360A"" |
| register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "sdmode_delay" = "5" |
| device generic 0 on end |
| end |
| chip drivers/sof |
| register "spkr_tplg" = "max98360a" |
| register "jack_tplg" = "rt5682" |
| register "mic_tplg" = "_2ch_pdm0" |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp4 on |
| # PCIe 4 WLAN |
| register "pch_pcie_rp[PCH_RP(4)]" = "{ |
| .clk_src = 2, |
| .clk_req = 2, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_DW1_03" |
| register "add_acpi_dma_property" = "true" |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp7 off end # PCIE7 no SD card |
| device ref emmc on end |
| device ref ish on |
| chip drivers/intel/ish |
| register "add_acpi_dma_property" = "true" |
| device generic 0 on end |
| end |
| end |
| device ref ufs on end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port2 on |
| probe DB_USB DB_1C |
| end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port2 on |
| probe DB_USB DB_1C |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 UFC"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port7 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port8 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""CNVi Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb3_port1 on end |
| end |
| end |
| end |
| end |
| end |
| end |