| /* SPDX-License-Identifier: GPL-2.0-only */ |
| |
| #include <baseboard/variants.h> |
| #include <chip.h> |
| #include <delay.h> |
| #include <device/device.h> |
| #include <device/pci_ids.h> |
| #include <device/pci_ops.h> |
| #include <ec/google/chromeec/ec.h> |
| #include <gpio.h> |
| #include <intelblocks/power_limit.h> |
| #include <soc/pci_devs.h> |
| #include <timer.h> |
| |
| #define GPIO_HDMI_HPD GPP_E13 |
| #define GPIO_DP_HPD GPP_E14 |
| |
| /* TODO: This can be moved to common directory */ |
| static void wait_for_hpd(gpio_t gpio, long timeout) |
| { |
| struct stopwatch sw; |
| |
| printk(BIOS_INFO, "Waiting for HPD\n"); |
| stopwatch_init_msecs_expire(&sw, timeout); |
| while (!gpio_get(gpio)) { |
| if (stopwatch_expired(&sw)) { |
| printk(BIOS_WARNING, |
| "HPD not ready after %ldms. Abort.\n", timeout); |
| return; |
| } |
| mdelay(200); |
| } |
| printk(BIOS_INFO, "HPD ready after %lu ms\n", |
| stopwatch_duration_msecs(&sw)); |
| } |
| |
| /* |
| * For type-C chargers, set PL2 to 90% of max power to account for |
| * cable loss and FET Rdson loss in the path from the source. |
| */ |
| #define SET_PSYSPL2(w) (9 * (w) / 10) |
| #define PUFF_U22_PL2 (35) |
| #define PUFF_U62_U42_PL2 (51) |
| #define PUFF_CELERON_PENTIUM_PSYSPL2 (65) |
| #define PUFF_CORE_CPU_PSYSPL2 (90) |
| #define PUFF_MAX_TIME_WINDOW 6 |
| #define PUFF_MIN_DUTYCYCLE 4 |
| |
| /* |
| * mainboard_set_power_limits |
| * |
| * Set Pl2 and SysPl2 values based on detected charger. |
| * Values are defined below but we use U22 value for all SKUs for now. |
| * definitions: |
| * x = no value entered. Use default value in parenthesis. |
| * will set 0 to anything that shouldn't be set. |
| * n = max value of power adapter. |
| * +-------------+-----+---------+-----------+-------+ |
| * | sku_id | PL2 | PsysPL2 | PsysPL3 | PL4 | |
| * +-------------+-----+---------+-----------+-------+ |
| * | i7 U42 | 51 | 90 | x(.85PL4) | x(82) | |
| * | i3 U22 | 35 | 65 | x(.85PL4) | x(51) | |
| * +-------------+-----+---------+-----------+-------+ |
| * For USB C charger: |
| * +-------------+-----------------+---------+---------+-------+ |
| * | Max Power(W)| PL2 | PsysPL2 | PsysPL3 | PL4 | |
| * +-------------+-----+-----------+---------+---------+-------+ |
| * | n | min(0.9n, PL2) | 0.9n | 0.9n | 0.9n | |
| * +-------------+-----+-----------+---------+---------+-------+ |
| */ |
| |
| /* |
| * Psys_pmax considerations |
| * |
| * Given the hardware design in puff, the serial shunt resistor is 0.01ohm. |
| * The full scale of hardware PSYS signal 0.8v maps to system current 9.6A |
| * instead of real system power. The equation is shown below: |
| * PSYS = 0.8v = (0.01ohm x Iinput) x 50 (INA213, gain 50V/V) x 15k/(15k + 75k) |
| * Hence, Iinput (Amps) = 9.6A |
| * Since there is no voltage information from PSYS, different voltage input |
| * would map to different Psys_pmax settings: |
| * For Type-C 15V, the Psys_pmax sholud be 15v x 9.6A = 144W |
| * For Type-C 20V, the Psys_pmax should be 20v x 9.6A = 192W |
| * For a barral jack, the Psys_pmax should be 19v x 9.6A = 182.4W |
| */ |
| #define PSYS_IMAX 9600 |
| #define BJ_VOLTS_MV 19000 |
| |
| static void mainboard_set_power_limits(struct soc_power_limits_config *conf) |
| { |
| enum usb_chg_type type; |
| u32 watts; |
| u16 volts_mv, current_ma; |
| u32 psyspl2 = PUFF_CELERON_PENTIUM_PSYSPL2; // default BJ value |
| u32 pl2 = PUFF_U22_PL2; // default PL2 for U22 |
| int rv = google_chromeec_get_usb_pd_power_info(&type, ¤t_ma, &volts_mv); |
| |
| struct device *dev = pcidev_path_on_root(SA_DEVFN_ROOT); |
| u16 mch_id = dev ? pci_read_config16(dev, PCI_DEVICE_ID) : 0xffff; |
| dev = pcidev_path_on_root(SA_DEVFN_IGD); |
| u16 igd_id = dev ? pci_read_config16(dev, PCI_DEVICE_ID) : 0xffff; |
| |
| /* use SoC default value for PsysPL3 and PL4 unless we're on USB-PD*/ |
| conf->tdp_psyspl3 = 0; |
| conf->tdp_pl4 = 0; |
| |
| if (rv == 0 && type == USB_CHG_TYPE_PD) { |
| /* Detected USB-PD. Base on max value of adapter */ |
| watts = ((u32)current_ma * volts_mv) / 1000000; |
| /* set psyspl2 to 90% of adapter rating */ |
| psyspl2 = SET_PSYSPL2(watts); |
| |
| /* Limit PL2 if the adapter is with lower capability */ |
| if (mch_id == PCI_DEVICE_ID_INTEL_CML_ULT || |
| mch_id == PCI_DEVICE_ID_INTEL_CML_ULT_6_2) |
| pl2 = (psyspl2 > PUFF_U62_U42_PL2) ? PUFF_U62_U42_PL2 : psyspl2; |
| else |
| pl2 = (psyspl2 > PUFF_U22_PL2) ? PUFF_U22_PL2 : psyspl2; |
| |
| conf->tdp_psyspl3 = psyspl2; |
| /* set max possible time window */ |
| conf->tdp_psyspl3_time = PUFF_MAX_TIME_WINDOW; |
| /* set minimum duty cycle */ |
| conf->tdp_psyspl3_dutycycle = PUFF_MIN_DUTYCYCLE; |
| /* No data about an arbitrary Type-C adapter, set pl4 conservatively. */ |
| conf->tdp_pl4 = psyspl2; |
| } else { |
| /* |
| * Input type is barrel jack, from the SKU matrix: |
| * 1. i3/i5/i7 SKUs use 90W BJ |
| * 2. Celeron and Pentium use 65W BJ (default) |
| */ |
| volts_mv = BJ_VOLTS_MV; |
| /* Use IGD ID to check if CPU is Core SKUs */ |
| if (igd_id != PCI_DEVICE_ID_INTEL_CML_GT1_ULT_1 && |
| igd_id != PCI_DEVICE_ID_INTEL_CML_GT2_ULT_5) { |
| psyspl2 = PUFF_CORE_CPU_PSYSPL2; |
| if (mch_id == PCI_DEVICE_ID_INTEL_CML_ULT || |
| mch_id == PCI_DEVICE_ID_INTEL_CML_ULT_6_2) |
| pl2 = PUFF_U62_U42_PL2; |
| } |
| } |
| /* voltage unit is milliVolts and current is in milliAmps */ |
| conf->psys_pmax = (u16)(((u32)PSYS_IMAX * volts_mv) / 1000000); |
| |
| conf->tdp_pl2_override = pl2; |
| conf->tdp_psyspl2 = psyspl2; |
| } |
| |
| void variant_ramstage_init(void) |
| { |
| static const long display_timeout_ms = 3000; |
| struct soc_power_limits_config *soc_config; |
| config_t *confg = config_of_soc(); |
| |
| /* This is reconfigured back to whatever FSP-S expects by gpio_configure_pads. */ |
| gpio_input(GPIO_HDMI_HPD); |
| gpio_input(GPIO_DP_HPD); |
| if (display_init_required() |
| && !gpio_get(GPIO_HDMI_HPD) |
| && !gpio_get(GPIO_DP_HPD)) { |
| /* This has to be done before FSP-S runs. */ |
| if (google_chromeec_wait_for_displayport(display_timeout_ms)) |
| wait_for_hpd(GPIO_DP_HPD, display_timeout_ms); |
| } |
| /* Psys_pmax needs to be setup before FSP-S */ |
| soc_config = &confg->power_limits_config; |
| mainboard_set_power_limits(soc_config); |
| } |