| chip soc/intel/alderlake |
| register "sagv" = "SaGv_Enabled" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| I2C0 | Audio | |
| #| I2C1 | cr50 TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[1] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST, |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| }, |
| }" |
| |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 1, |
| .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL | |
| FIVR_VOLTAGE_MIN_ACTIVE | |
| FIVR_VOLTAGE_MIN_RETENTION, |
| .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL | |
| FIVR_VOLTAGE_MIN_ACTIVE | |
| FIVR_VOLTAGE_MIN_RETENTION, |
| .v1p05_icc_max_ma = 500, |
| .vnn_sx_voltage_mv = 1250, |
| }" |
| |
| register "usb2_ports[3]" = "USB2_PORT_EMPTY" # Disable Port 3 |
| register "usb2_ports[4]" = "USB2_PORT_EMPTY" # Disable Port 4 |
| register "usb2_ports[6]" = "USB2_PORT_EMPTY" # Disable Port 6 |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # DCI port |
| register "usb2_ports[8]" = "USB2_PORT_TYPE_C(OC3)" # USB2_C3 |
| |
| register "usb3_ports[0]" = "USB3_PORT_EMPTY" |
| register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # DCI port |
| register "usb3_ports[2]" = "USB3_PORT_EMPTY" |
| register "usb3_ports[3]" = "USB3_PORT_EMPTY" |
| |
| register "tcss_ports[3]" = "TCSS_PORT_DEFAULT(OC3)" |
| |
| # I2C Port Config |
| register "serial_io_i2c_mode" = "{ |
| [PchSerialIoIndexI2C0] = PchSerialIoPci, |
| [PchSerialIoIndexI2C1] = PchSerialIoPci, |
| [PchSerialIoIndexI2C2] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C3] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C4] = PchSerialIoDisabled, |
| [PchSerialIoIndexI2C5] = PchSerialIoPci, |
| }" |
| |
| register "serial_io_gspi_mode" = "{ |
| [PchSerialIoIndexGSPI0] = PchSerialIoDisabled, |
| [PchSerialIoIndexGSPI1] = PchSerialIoDisabled, |
| }" |
| |
| register "tcc_offset" = "10" # TCC of 90 |
| |
| device domain 0 on |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""DRAM_SOC"" |
| register "options.tsr[1].desc" = ""Ambient"" |
| register "options.tsr[2].desc" = ""Charger"" |
| |
| # TODO: below values are initial reference values only |
| ## Active Policy |
| register "policies.active" = "{ |
| [0] = { |
| .target = DPTF_CPU, |
| .thresholds = { |
| TEMP_PCT(57, 78), |
| TEMP_PCT(54, 70), |
| TEMP_PCT(51, 60), |
| TEMP_PCT(48, 50), |
| TEMP_PCT(44, 37), |
| } |
| }, |
| [1] = { |
| .target = DPTF_TEMP_SENSOR_1, |
| .thresholds = { |
| TEMP_PCT(55, 78), |
| TEMP_PCT(52, 70), |
| TEMP_PCT(49, 60), |
| TEMP_PCT(46, 50), |
| TEMP_PCT(43, 37), |
| } |
| } |
| }" |
| |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 85, 5000), |
| [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 85, 5000), |
| [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 85, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 127, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 90, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 90, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 90, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 5000, |
| .max_power = 30000, |
| .time_window_min = 30 * MSECS_PER_SEC, |
| .time_window_max = 30 * MSECS_PER_SEC, |
| .granularity = 100, |
| }, |
| .pl2 = { |
| .min_power = 60000, |
| .max_power = 60000, |
| .time_window_min = 32 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 500, |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| ## Fan Performance Control (Percent, Speed, Noise, Power) |
| register "controls.fan_perf" = "{ |
| [0] = { 90, 6700, 220, 2200, }, |
| [1] = { 80, 5800, 180, 1800, }, |
| [2] = { 70, 5000, 145, 1450, }, |
| [3] = { 60, 4900, 115, 1150, }, |
| [4] = { 50, 3838, 90, 900, }, |
| [5] = { 40, 2904, 55, 550, }, |
| [6] = { 30, 2337, 30, 300, }, |
| [7] = { 20, 1608, 15, 150, }, |
| [8] = { 10, 800, 10, 100, }, |
| [9] = { 0, 0, 0, 50, } |
| }" |
| |
| ## Fan options |
| register "options.fan.fine_grained_control" = "1" |
| register "options.fan.step_size" = "2" |
| |
| device generic 0 alias dptf_policy on end |
| end |
| end |
| device ref pcie4_0 on |
| # Enable CPU PCIE RP 1 using CLK 0 |
| register "cpu_pcie_rp[CPU_RP(1)]" = "{ |
| .clk_req = 0, |
| .clk_src = 0, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| end |
| device ref tbt_pcie_rp3 on end |
| device ref cnvi_wifi on |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_PME_B0" |
| device generic 0 on end |
| end |
| end |
| device ref pcie_rp6 off end |
| device ref pcie_rp8 off end |
| device ref pcie_rp9 off end |
| device ref tcss_dma0 on |
| chip drivers/intel/usb4/retimer |
| register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| register "dfp[1].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| use tcss_usb3_port1 as dfp[0].typec_port |
| use tcss_usb3_port2 as dfp[1].typec_port |
| device generic 0 on end |
| end |
| end |
| device ref tcss_dma1 on |
| chip drivers/intel/usb4/retimer |
| register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| register "dfp[1].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" |
| use tcss_usb3_port3 as dfp[0].typec_port |
| use tcss_usb3_port4 as dfp[1].typec_port |
| device generic 0 on end |
| end |
| end |
| device ref i2c0 on |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| chip drivers/generic/gpio_keys |
| register "name" = ""MUTE"" |
| register "label" = ""mic_mute_switch"" |
| register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_HIGH(GPP_F22)" |
| register "key.wakeup_route" = "WAKEUP_ROUTE_DISABLED" |
| register "key.dev_name" = ""MMSW"" |
| register "key.linux_code" = "SW_MUTE_DEVICE" |
| register "key.linux_input_type" = "EV_SW" |
| register "key.label" = ""mic_mute_switch_key"" |
| device generic 0 on end |
| end |
| end #I2C0 |
| device ref i2c1 on |
| chip drivers/i2c/tpm |
| register "hid" = ""GOOG0005"" |
| register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" |
| device i2c 50 on end |
| end |
| end |
| device ref i2c5 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PNP0C50"" |
| register "generic.desc" = ""PIXART Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.probed" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 2c on end |
| end |
| end |
| device ref hda on |
| chip drivers/generic/max98357a |
| register "hid" = ""MX98360A"" |
| register "sdmode_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| register "sdmode_delay" = "5" |
| device generic 0 on end |
| end |
| end |
| device ref gspi1 off end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| use conn2 as mux_conn[2] |
| use conn3 as mux_conn[3] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port3 as usb2_port |
| use tcss_usb3_port3 as usb3_port |
| device generic 2 alias conn2 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port9 as usb2_port |
| use tcss_usb3_port4 as usb3_port |
| device generic 3 alias conn3 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C2 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref tcss_usb3_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C3 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref tcss_usb3_port4 on end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C2 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Camera"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "privacy_gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F19)" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C3 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb2_port9 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| end |
| end |
| end |
| device ref smbus on end |
| end |
| end |