| /* |
| * This file is part of the coreboot project. |
| * |
| * Copyright (C) 2007-2009 coresystems GmbH |
| * Copyright (C) 2011 Sven Schnelle <svens@stackframe.org> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; version 2 of |
| * the License. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, |
| * MA 02110-1301 USA |
| */ |
| |
| // __PRE_RAM__ means: use "unsigned" for device, not a struct. |
| |
| #include <stdint.h> |
| #include <string.h> |
| #include <arch/io.h> |
| #include <device/pci_def.h> |
| #include <device/pnp_def.h> |
| #include <cpu/x86/lapic.h> |
| #include <lib.h> |
| #include <cbmem.h> |
| #include <timestamp.h> |
| #include <pc80/mc146818rtc.h> |
| #include <console/console.h> |
| #include <cpu/x86/bist.h> |
| #include "northbridge/intel/i945/i945.h" |
| #include "northbridge/intel/i945/raminit.h" |
| #include "southbridge/intel/i82801gx/i82801gx.h" |
| |
| void setup_ich7_gpios(void) |
| { |
| printk(BIOS_DEBUG, " GPIOS..."); |
| |
| /* X60 GPIO: |
| * 1: HDD_PRESENCE# |
| * 6: Unknown (Pulled high by R215 to VCC3B) |
| * 7: BDC_PRESENCE# |
| * 8: H8_WAKE# |
| * 9: RTC_BAT_IN# |
| * 10: Unknown (Pulled high by R700 to VCC3M) |
| * 12: H8SCI# |
| * 13: SLICE_ON_3M# |
| * 14: Unknown (Pulled high by R321 to VCC3) |
| * 15: Unknown (Pulled high by R258 to VCC3) |
| * 19: Unknown (Pulled low by R594) |
| * 21: Unknown (Pulled high by R145 to VCC3) |
| * 22: FWH_WP# |
| * 25: MDC_KILL# |
| * 33: HDD_PRESENCE_2# |
| * 35: CLKREQ_SATA# |
| * 36: PLANARID0 |
| * 37: PLANARID1 |
| * 38: PLANARID2 |
| * 39: PLANARID3 |
| * 48: FWH_TBL# |
| */ |
| |
| outl(0x1f40f7e2, DEFAULT_GPIOBASE + 0x00); /* GPIO_USE_SEL */ |
| outl(0xfea8af83, DEFAULT_GPIOBASE + 0x04); /* GP_IO_SEL */ |
| outl(0xfcc06bdf, DEFAULT_GPIOBASE + 0x0c); /* GP_LVL */ |
| /* Output Control Registers */ |
| outl(0x00000000, DEFAULT_GPIOBASE + 0x18); /* GPO_BLINK */ |
| /* Input Control Registers */ |
| outl(0x00002082, DEFAULT_GPIOBASE + 0x2c); /* GPI_INV */ |
| outl(0x000100c0, DEFAULT_GPIOBASE + 0x30); /* GPIO_USE_SEL2 */ |
| outl(0x00000030, DEFAULT_GPIOBASE + 0x34); /* GP_IO_SEL2 */ |
| outl(0x000100c0, DEFAULT_GPIOBASE + 0x38); /* GP_LVL2 */ |
| } |
| |
| static void ich7_enable_lpc(void) |
| { |
| // Enable Serial IRQ |
| pci_write_config8(PCI_DEV(0, 0x1f, 0), 0x64, 0xd0); |
| |
| // I/O Decode Ranges |
| // X60: 0x0210 == 00000010 00010000 |
| // Macbook21: 0x0010 == 00000000 00010000 |
| // Bit 9:8 LPT Decode Range. This field determines which range to |
| // decode for the LPT Port. |
| // 00 = 378h 37Fh and 778h 77Fh |
| // 10 = 3BCh 3BEh and 7BCh 7BEh |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x80, 0x0010); |
| |
| // LPC_EN--LPC I/F Enables Register |
| // X60: 0x1f0d == 00011111 00001101 |
| // Macbook21: 0x3807 == 00111000 00000111 |
| // Bit 13 CNF2_LPC_EN -- R/W. Microcontroller Enable # 2. |
| // 0 = Disable. |
| // 1 = Enables the decoding of the I/O locations 4Eh and 4Fh |
| // to the LPC interface. This range is used for a |
| // microcontroller. |
| // Bit 12 CNF1_LPC_EN -- R/W. Super I/O Enable. |
| // 0 = Disable. |
| // 1 = Enables the decoding of the I/O locations 2Eh and 2Fh |
| // to the LPC interface. This range is used for |
| // Super I/O devices. |
| // Bit 11 MC_LPC_EN -- R/W. Microcontroller Enable # 1. |
| // 0 = Disable. |
| // 1 = Enables the decoding of the I/O locations 62h and 66h |
| // to the LPC interface. This range is used for a |
| // microcontroller. |
| // Bit 10 KBC_LPC_EN -- R/W. Keyboard Enable. |
| // 0 = Disable. |
| // 1 = Enables the decoding of the I/O locations 60h and 64h |
| // to the LPC interface. This range is used for a |
| // microcontroller. |
| // Bit 9 GAMEH_LPC_EN -- R/W. High Gameport Enable |
| // 0 = Disable. |
| // 1 = Enables the decoding of the I/O locations 208h to 20Fh |
| // to the LPC interface. This range is used for a gameport. |
| // Bit 8 GAMEL_LPC_EN -- R/W. Low Gameport Enable |
| // 0 = Disable. |
| // 1 = Enables the decoding of the I/O locations 200h to 207h |
| // to the LPC interface. This range is used for a gameport. |
| // Bit 3 FDD_LPC_EN -- R/W. Floppy Drive Enable |
| // 0 = Disable. |
| // 1 = Enables the decoding of the FDD range to the LPC |
| // interface. This range is selected in the LPC_FDD/LPT |
| // Decode Range Register (D31:F0:80h, bit 12). |
| // Bit 2 LPT_LPC_EN -- R/W. Parallel Port Enable |
| // 0 = Disable. |
| // 1 = Enables the decoding of the LPT range to the LPC |
| // interface. This range is selected in the LPC_FDD/LPT |
| // Decode Range Register (D31:F0:80h, bit 9:8). |
| // Bit 1 COMB_LPC_EN -- R/W. Com Port B Enable |
| // 0 = Disable. |
| // 1 = Enables the decoding of the COMB range to the LPC |
| // interface. This range is selected in the LPC_COM Decode |
| // Range Register (D31:F0:80h, bits 6:4). |
| // Bit 0 COMA_LPC_EN -- R/W. Com Port A Enable |
| // 0 = Disable. |
| // 1 = Enables the decoding of the COMA range to the LPC |
| // interface. This range is selected in the LPC_COM Decode |
| // Range Register (D31:F0:80h, bits 3:2). |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x82, 0x3807); |
| |
| /* GEN1_DEC, LPC Interface Generic Decode Range 1 */ |
| // X60: 0x1601 0x007c == 00000000 01111100 00010110 00000001 |
| // Macbook21: 0x0681 0x000c == 00000000 00001100 00000110 10000001 |
| // Bit 31:24 Reserved. |
| // Bit 23:18 Generic I/O Decode Range Address[7:2] Mask: A `1' in any |
| // bit position indicates that any value in the corresponding |
| // address bit in a received cycle will be treated as a |
| // match. The corresponding bit in the Address field, below, |
| // is ignored. The mask is only provided for the lower 6 bits |
| // of the DWord address, allowing for decoding blocks up to |
| // 256 bytes in size. |
| // Bit 17:16 Reserved. |
| // Bit 15:2 Generic I/O Decode Range 1 Base Address (GEN1_BASE). This |
| // address is aligned on a 128-byte boundary, and must have |
| // address lines 31:16 as 0. NOTE: The Intel ICH7 does not |
| // provide decode down to the word or byte level. |
| // Bit 1 Reserved. |
| // Bit 0 Generic Decode Range 1 Enable (GEN1_EN) -- R/W. |
| // 0 = Disable. |
| // 1 = Enable the GEN1 I/O range to be forwarded to the LPC |
| // I/F |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x84, 0x0681); |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x86, 0x000c); |
| |
| /* GEN2_DEC, LPC Interface Generic Decode Range 2 */ |
| // X60: 0x15e1 0x000c == 00000000 00001100 00010101 11100001 |
| // Macbook21: 0x1641 0x000c == 00000000 00001100 00010110 01000001 |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x88, 0x1641); |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x8a, 0x000c); |
| |
| /* GEN3_DEC, LPC Interface Generic Decode Range 3 */ |
| // X60: 0x1681 0x001c == 00000000 00011100 00010110 10000001 |
| // Macbook21: 0x0000 0x0000 |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x8c, 0x0000); // obsolete, because it writes zeros? |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x8e, 0x0000); |
| |
| /* GEN4_DEC, LPC Interface Generic Decode Range 4 */ |
| // X60: 0x0000 0x0000 |
| // Macbook21: 0x0301 0x001c == 00000000 00011100 00000011 00000001 |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x90, 0x0301); |
| pci_write_config16(PCI_DEV(0, 0x1f, 0), 0x92, 0x001c); |
| } |
| |
| static void rcba_config(void) |
| { |
| /* V0CTL Virtual Channel 0 Resource Control */ |
| RCBA32(0x0014) = 0x80000001; |
| /* V1CAP Virtual Channel 1 Resource Capability */ |
| RCBA32(0x001c) = 0x03128010; |
| |
| /* Device 1f interrupt pin register */ |
| RCBA32(0x3100) = 0x00042210; |
| RCBA32(0x3108) = 0x10004321; |
| |
| /* PCIe Interrupts */ |
| RCBA32(0x310c) = 0x00214321; |
| /* HD Audio Interrupt */ |
| RCBA32(0x3110) = 0x00000001; |
| |
| /* dev irq route register */ |
| RCBA16(0x3140) = 0x0232; |
| RCBA16(0x3142) = 0x3246; |
| RCBA16(0x3144) = 0x0235; |
| RCBA16(0x3146) = 0x3201; |
| RCBA16(0x3148) = 0x3216; |
| |
| /* Enable IOAPIC */ |
| RCBA8(0x31ff) = 0x03; |
| |
| /* Enable upper 128bytes of CMOS */ |
| RCBA32(0x3400) = (1 << 2); |
| |
| /* Disable unused devices */ |
| RCBA32(0x3418) = FD_PCIE6 | FD_PCIE5 | FD_PCIE4 | FD_PCIE3 | FD_INTLAN | FD_ACMOD | FD_ACAUD; |
| RCBA32(0x3418) |= (1 << 0); // Required. |
| |
| /* Set up I/O Trap #0 for 0xfe00 (SMIC) */ |
| // RCBA32(0x1e84) = 0x00020001; |
| // RCBA32(0x1e80) = 0x0000fe01; |
| |
| /* Set up I/O Trap #3 for 0x800-0x80c (Trap) */ |
| RCBA32(0x1e9c) = 0x000200f0; |
| RCBA32(0x1e98) = 0x000c0801; |
| } |
| |
| static void early_ich7_init(void) |
| { |
| uint8_t reg8; |
| uint32_t reg32; |
| |
| // program secondary mlt XXX byte? |
| pci_write_config8(PCI_DEV(0, 0x1e, 0), 0x1b, 0x20); |
| |
| // reset rtc power status |
| reg8 = pci_read_config8(PCI_DEV(0, 0x1f, 0), 0xa4); |
| reg8 &= ~(1 << 2); |
| pci_write_config8(PCI_DEV(0, 0x1f, 0), 0xa4, reg8); |
| |
| // usb transient disconnect |
| reg8 = pci_read_config8(PCI_DEV(0, 0x1f, 0), 0xad); |
| reg8 |= (3 << 0); |
| pci_write_config8(PCI_DEV(0, 0x1f, 0), 0xad, reg8); |
| |
| reg32 = pci_read_config32(PCI_DEV(0, 0x1d, 7), 0xfc); |
| reg32 |= (1 << 29) | (1 << 17); |
| pci_write_config32(PCI_DEV(0, 0x1d, 7), 0xfc, reg32); |
| |
| reg32 = pci_read_config32(PCI_DEV(0, 0x1d, 7), 0xdc); |
| reg32 |= (1 << 31) | (1 << 27); |
| pci_write_config32(PCI_DEV(0, 0x1d, 7), 0xdc, reg32); |
| |
| RCBA32(0x0088) = 0x0011d000; |
| RCBA16(0x01fc) = 0x060f; |
| RCBA32(0x01f4) = 0x86000040; |
| RCBA32(0x0214) = 0x10030549; |
| RCBA32(0x0218) = 0x00020504; |
| RCBA8(0x0220) = 0xc5; |
| reg32 = RCBA32(0x3410); |
| reg32 |= (1 << 6); |
| RCBA32(0x3410) = reg32; |
| reg32 = RCBA32(0x3430); |
| reg32 &= ~(3 << 0); |
| reg32 |= (1 << 0); |
| RCBA32(0x3430) = reg32; |
| RCBA32(0x3418) |= (1 << 0); |
| RCBA16(0x0200) = 0x2008; |
| RCBA8(0x2027) = 0x0d; |
| RCBA16(0x3e08) |= (1 << 7); |
| RCBA16(0x3e48) |= (1 << 7); |
| RCBA32(0x3e0e) |= (1 << 7); |
| RCBA32(0x3e4e) |= (1 << 7); |
| |
| // next step only on ich7m b0 and later: |
| reg32 = RCBA32(0x2034); |
| reg32 &= ~(0x0f << 16); |
| reg32 |= (5 << 16); |
| RCBA32(0x2034) = reg32; |
| } |
| |
| void main(unsigned long bist) |
| { |
| int s3resume = 0; |
| const u8 spd_addrmap[2 * DIMM_SOCKETS] = { 0x50, 0x51, 0x52, 0x53 }; |
| |
| timestamp_init(get_initial_timestamp()); |
| timestamp_add_now(TS_START_ROMSTAGE); |
| |
| if (bist == 0) |
| enable_lapic(); |
| |
| /* Force PCIRST# */ |
| pci_write_config16(PCI_DEV(0, 0x1e, 0), BCTRL, SBR); |
| udelay(200 * 1000); |
| pci_write_config16(PCI_DEV(0, 0x1e, 0), BCTRL, 0); |
| |
| ich7_enable_lpc(); |
| |
| /* Set up the console */ |
| console_init(); |
| |
| /* Halt if there was a built in self test failure */ |
| report_bist_failure(bist); |
| |
| if (MCHBAR16(SSKPD) == 0xCAFE) { |
| printk(BIOS_DEBUG, |
| "Soft reset detected, rebooting properly.\n"); |
| outb(0x6, 0xcf9); |
| while (1) |
| asm("hlt"); |
| } |
| |
| /* Perform some early chipset initialization required |
| * before RAM initialization can work |
| */ |
| i945_early_initialization(); |
| |
| s3resume = southbridge_detect_s3_resume(); |
| |
| /* Enable SPD ROMs and DDR-II DRAM */ |
| enable_smbus(); |
| |
| #if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8 |
| dump_spd_registers(); |
| #endif |
| |
| timestamp_add_now(TS_BEFORE_INITRAM); |
| sdram_initialize(s3resume ? 2 : 0, spd_addrmap); |
| timestamp_add_now(TS_AFTER_INITRAM); |
| |
| /* Perform some initialization that must run before stage2 */ |
| early_ich7_init(); |
| |
| /* This should probably go away. Until now it is required |
| * and mainboard specific |
| */ |
| rcba_config(); |
| |
| /* Chipset Errata! */ |
| fixup_i945_errata(); |
| |
| /* Initialize the internal PCIe links before we go into stage2 */ |
| i945_late_initialization(s3resume); |
| |
| timestamp_add_now(TS_END_ROMSTAGE); |
| |
| } |