| # SPDX-License-Identifier: GPL-2.0-or-later |
| |
| chip soc/amd/mendocino |
| |
| # Set Package Power Parameters |
| register "thermctl_limit_degreeC" = "92" |
| |
| # STT settings |
| register "stt_control" = "1" |
| register "stt_pcb_sensor_count" = "2" |
| register "stt_error_coeff" = "0x0038" |
| register "stt_error_rate_coefficient" = "0x0ed9" |
| register "stt_min_limit" = "15000" |
| register "stt_skin_temp_apu" = "0x2700" |
| |
| # STT default mode |
| register "stt_m1" = "0x036b" |
| register "stt_m2" = "0x0022" |
| register "stt_c_apu" = "0xffc1" |
| register "stt_alpha_apu" = "0x199a" |
| |
| # set usb3 port force to gen1 |
| register "usb3_port_force_gen1" = "{ |
| .ports.xhci0_port0 = 1, |
| .ports.xhci1_port0 = 1, |
| .ports.xhci1_port1 = 0, |
| }" |
| |
| device domain 0 on |
| |
| register "dxio_tx_vboost_enable" = "1" |
| |
| device ref gpp_bridge_1 on |
| # Required so the NVMe gets placed into D3 when entering S0i3. |
| chip drivers/pcie/rtd3/device |
| register "name" = ""NVME"" |
| device pci 00.0 on end |
| end |
| end # NVME |
| device ref gpp_bridge_2 on |
| # Required so the NVMe gets placed into D3 when entering S0i3. |
| chip drivers/pcie/rtd3/device |
| register "name" = ""NVME"" |
| device pci 00.0 on end |
| end |
| end # NVME |
| |
| device ref gpp_bridge_a on # Internal GPP Bridge 0 to Bus A |
| device ref xhci_1 on # XHCI1 controller |
| chip drivers/usb/acpi |
| device ref xhci_1_root_hub on # XHCI1 root hub |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(2, 2))" |
| device ref usb3_port3 on end # USB 3.1 port3 |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(2, 2))" |
| device ref usb2_port3 on end # USB 2 port3 |
| end |
| end # XHCI1 root hub |
| end |
| end # XHCI1 controller |
| end # Internal GPP Bridge 0 to Bus A |
| end # domain |
| |
| device ref i2c_0 on |
| chip drivers/i2c/generic |
| register "hid" = ""ELAN0000"" |
| register "desc" = ""ELAN Touchpad"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_LOW(GPIO_40)" |
| register "wake" = "GEVENT_20" |
| register "detect" = "1" |
| device i2c 15 on end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""SYNA0000"" |
| register "generic.cid" = ""ACPI0C50"" |
| register "generic.desc" = ""Synaptics Touchpad"" |
| register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_40)" |
| register "generic.wake" = "GEVENT_20" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x20" |
| device i2c 2c on end |
| end |
| end # I2C0 |
| device ref i2c_1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN9004"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPIO_29)" |
| register "generic.detect" = "1" |
| register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_131)" |
| register "generic.enable_delay_ms" = "10" |
| register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_136)" |
| register "generic.reset_off_delay_ms" = "1" |
| register "generic.reset_delay_ms" = "10" |
| register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPIO_76)" |
| register "generic.stop_delay_ms" = "150" |
| register "generic.stop_off_delay_ms" = "1" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 10 on end |
| end |
| end # I2C1 |
| device ref i2c_2 on |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Realtek RT5682"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPIO_90)" |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1019"" |
| register "desc" = ""Realtek SPK AMP R"" |
| register "uid" = "1" |
| device i2c 29 on end |
| end |
| chip drivers/i2c/generic |
| register "hid" = ""10EC1019"" |
| register "desc" = ""Realtek SPK AMP L"" |
| register "uid" = "2" |
| register "probed" = "1" |
| device i2c 2a on end |
| end |
| end # I2C2 |
| |
| end # chip soc/amd/mendocino |