| fw_config |
| field DB_USB 0 1 |
| option DB_NONE 0 |
| option DB_C_A 1 |
| option DB_C_A_LTE 2 |
| option DB_A 3 |
| end |
| field THERMAL_SOLUTION 2 |
| option THERMAL_SOLUTION_PASSIVE 0 |
| option THERMAL_SOLUTION_ACTIVE 1 |
| end |
| field WLAN 3 4 |
| option WLAN_MT7921_AZUREWAVE 0 |
| option WLAN_AX211_Intel 1 |
| end |
| field AUDIO 5 6 |
| option AUDIO_ALC1019_ALC5682IVS 0 |
| end |
| field STYLUS 7 |
| option STYLUS_ABSENT 0 |
| option STYLUS_PRESENT 1 |
| end |
| field WFC 8 |
| option WFC_PRESENT 0 |
| option WFC_ABSENT 1 |
| end |
| field TOUCH_PANEL 9 |
| option TOUCH_PANEL_ENABLE 0 |
| option TOUCH_PANEL_DISABLE 1 |
| end |
| end |
| |
| chip soc/intel/alderlake |
| register "sagv" = "SaGv_Enabled" |
| |
| # EMMC Tx CMD Delay |
| # Refer to EDS-Vol2-42.3.7. |
| # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" |
| |
| # EMMC TX DATA Delay 1 |
| # Refer to EDS-Vol2-42.3.8. |
| # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. |
| # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" |
| |
| # EMMC TX DATA Delay 2 |
| # Refer to EDS-Vol2-42.3.9. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. |
| # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828" |
| |
| # EMMC RX CMD/DATA Delay 1 |
| # Refer to EDS-Vol2-42.3.10. |
| # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. |
| # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. |
| # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. |
| # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F1B" |
| |
| # EMMC RX CMD/DATA Delay 2 |
| # Refer to EDS-Vol2-42.3.12. |
| # [17:16] stands for Rx Clock before Output Buffer, |
| # 00: Rx clock after output buffer, |
| # 01: Rx clock before output buffer, |
| # 10: Automatic selection based on working mode. |
| # 11: Reserved |
| # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. |
| # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. |
| register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10005" |
| |
| # EMMC Rx Strobe Delay |
| # Refer to EDS-Vol2-42.3.11. |
| # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. |
| # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. |
| register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x11515" |
| |
| # Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC. |
| # Bit 2 - C1 has a redriver which does SBU muxing. |
| # Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1. |
| register "tcss_aux_ori" = "5" |
| |
| register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" |
| register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" |
| |
| # Configure external V1P05/Vnn/VnnSx Rails |
| register "ext_fivr_settings" = "{ |
| .configure_ext_fivr = 1, |
| .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0, |
| .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX, |
| .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL, |
| .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE, |
| .v1p05_voltage_mv = 1050, |
| .vnn_voltage_mv = 780, |
| .vnn_sx_voltage_mv = 1050, |
| .v1p05_icc_max_ma = 500, |
| .vnn_icc_max_ma = 500, |
| }" |
| |
| # Intel Common SoC Config |
| #+-------------------+---------------------------+ |
| #| Field | Value | |
| #+-------------------+---------------------------+ |
| #| I2C0 | TPM. Early init is | |
| #| | required to set up a BAR | |
| #| | for TPM communication | |
| #| I2C1 | Touchscreen | |
| #| I2C2 | Sub-board(PSensor)/WCAM | |
| #| I2C3 | Audio | |
| #| I2C5 | Trackpad | |
| #+-------------------+---------------------------+ |
| register "common_soc_config" = "{ |
| .i2c[0] = { |
| .early_init = 1, |
| .speed = I2C_SPEED_FAST_PLUS, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST_PLUS, |
| .scl_lcnt = 55, |
| .scl_hcnt = 30, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[1] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 160, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[2] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 157, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[3] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 157, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| .i2c[5] = { |
| .speed = I2C_SPEED_FAST, |
| .speed_config[0] = { |
| .speed = I2C_SPEED_FAST, |
| .scl_lcnt = 152, |
| .scl_hcnt = 79, |
| .sda_hold = 7, |
| } |
| }, |
| }" |
| |
| device domain 0 on |
| device ref dtt on |
| chip drivers/intel/dptf |
| ## sensor information |
| register "options.tsr[0].desc" = ""Memory"" |
| register "options.tsr[1].desc" = ""Charger"" |
| register "options.tsr[2].desc" = ""Ambient"" |
| |
| # TODO: below values are initial reference values only |
| ## Passive Policy |
| register "policies.passive" = "{ |
| [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), |
| [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), |
| [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), |
| [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), |
| }" |
| |
| ## Critical Policy |
| register "policies.critical" = "{ |
| [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), |
| [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), |
| [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), |
| [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), |
| }" |
| |
| register "controls.power_limits" = "{ |
| .pl1 = { |
| .min_power = 3000, |
| .max_power = 6000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 200 |
| }, |
| .pl2 = { |
| .min_power = 25000, |
| .max_power = 25000, |
| .time_window_min = 28 * MSECS_PER_SEC, |
| .time_window_max = 32 * MSECS_PER_SEC, |
| .granularity = 1000 |
| } |
| }" |
| |
| ## Charger Performance Control (Control, mA) |
| register "controls.charger_perf" = "{ |
| [0] = { 255, 1700 }, |
| [1] = { 24, 1500 }, |
| [2] = { 16, 1000 }, |
| [3] = { 8, 500 } |
| }" |
| |
| device generic 0 on end |
| end |
| end |
| device ref i2c1 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ELAN7B13"" |
| register "generic.desc" = ""ELAN Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "300" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "6" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x10 on |
| probe TOUCH_PANEL TOUCH_PANEL_ENABLE |
| end |
| end |
| chip drivers/i2c/hid |
| register "generic.hid" = ""ILI2901"" |
| register "generic.desc" = ""ILI Touchscreen"" |
| register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" |
| register "generic.detect" = "1" |
| register "generic.reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" |
| register "generic.reset_delay_ms" = "200" |
| register "generic.reset_off_delay_ms" = "2" |
| register "generic.enable_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" |
| register "generic.enable_delay_ms" = "6" |
| register "generic.has_power_resource" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 0x41 on |
| probe TOUCH_PANEL TOUCH_PANEL_ENABLE |
| end |
| end |
| end |
| device ref i2c2 on |
| chip drivers/i2c/sx9324 |
| register "desc" = ""SAR2 Proximity Sensor"" |
| register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)" |
| register "speed" = "I2C_SPEED_FAST" |
| register "uid" = "1" |
| register "reg_gnrl_ctrl0" = "0x16" |
| register "reg_gnrl_ctrl1" = "0x21" |
| register "reg_afe_ctrl0" = "0x20" |
| register "reg_afe_ctrl1" = "0x10" |
| register "reg_afe_ctrl2" = "0x00" |
| register "reg_afe_ctrl3" = "0x01" |
| register "reg_afe_ctrl4" = "0x46" |
| register "reg_afe_ctrl5" = "0x00" |
| register "reg_afe_ctrl6" = "0x00" |
| register "reg_afe_ctrl7" = "0x07" |
| register "reg_afe_ctrl8" = "0x12" |
| register "reg_afe_ctrl9" = "0x0f" |
| register "reg_prox_ctrl0" = "0x12" |
| register "reg_prox_ctrl1" = "0x12" |
| register "reg_prox_ctrl2" = "0x90" |
| register "reg_prox_ctrl3" = "0x60" |
| register "reg_prox_ctrl4" = "0x0c" |
| register "reg_prox_ctrl5" = "0x12" |
| register "reg_prox_ctrl6" = "0x3c" |
| register "reg_prox_ctrl7" = "0x58" |
| register "reg_adv_ctrl0" = "0x00" |
| register "reg_adv_ctrl1" = "0x00" |
| register "reg_adv_ctrl2" = "0x00" |
| register "reg_adv_ctrl3" = "0x00" |
| register "reg_adv_ctrl4" = "0x00" |
| register "reg_adv_ctrl5" = "0x05" |
| register "reg_adv_ctrl6" = "0x00" |
| register "reg_adv_ctrl7" = "0x00" |
| register "reg_adv_ctrl8" = "0x00" |
| register "reg_adv_ctrl9" = "0x00" |
| register "reg_adv_ctrl10" = "0x5c" |
| register "reg_adv_ctrl11" = "0x52" |
| register "reg_adv_ctrl12" = "0xb5" |
| register "reg_adv_ctrl13" = "0x00" |
| register "reg_adv_ctrl14" = "0x80" |
| register "reg_adv_ctrl15" = "0x0c" |
| register "reg_adv_ctrl16" = "0x38" |
| register "reg_adv_ctrl17" = "0x56" |
| register "reg_adv_ctrl18" = "0x33" |
| register "reg_adv_ctrl19" = "0xf0" |
| register "reg_adv_ctrl20" = "0xf0" |
| |
| register "ph0_pin" = "{1, 3, 3}" |
| register "ph1_pin" = "{3, 2, 1}" |
| register "ph2_pin" = "{3, 3, 1}" |
| register "ph3_pin" = "{1, 3, 3}" |
| register "ph01_resolution" = "512" |
| register "ph23_resolution" = "1024" |
| register "startup_sensor" = "1" |
| register "ph01_proxraw_strength" = "2" |
| register "ph23_proxraw_strength" = "2" |
| register "avg_pos_strength" = "256" |
| register "cs_idle_sleep" = ""gnd"" |
| register "int_comp_resistor" = ""lowest"" |
| register "input_precharge_resistor_ohms" = "4000" |
| register "input_analog_gain" = "3" |
| device i2c 28 on |
| probe DB_USB DB_C_A_LTE |
| end |
| end |
| end |
| device ref i2c3 on |
| chip drivers/i2c/generic |
| register "hid" = ""RTL5682"" |
| register "name" = ""RT58"" |
| register "desc" = ""Headset Codec"" |
| register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" |
| # Set the jd_src to RT5668_JD1 for jack detection |
| register "property_count" = "1" |
| register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" |
| register "property_list[0].name" = ""realtek,jd-src"" |
| register "property_list[0].integer" = "1" |
| device i2c 1a on end |
| end |
| chip drivers/generic/alc1015 |
| register "hid" = ""RTL1019"" |
| register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" |
| device generic 0 on end |
| end |
| end |
| |
| device ref i2c5 on |
| chip drivers/i2c/hid |
| register "generic.hid" = ""PNP0C50"" |
| register "generic.desc" = ""PIXART Touchpad"" |
| register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" |
| register "generic.wake" = "GPE0_DW2_14" |
| register "generic.detect" = "1" |
| register "hid_desc_reg_offset" = "0x01" |
| device i2c 15 on end |
| end |
| end |
| device ref pcie_rp4 on |
| # PCIe 4 WLAN |
| register "pch_pcie_rp[PCH_RP(4)]" = "{ |
| .clk_src = 2, |
| .clk_req = 2, |
| .flags = PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip drivers/wifi/generic |
| register "wake" = "GPE0_DW1_03" |
| register "add_acpi_dma_property" = "true" |
| device pci 00.0 on end |
| end |
| end |
| device ref pcie_rp7 on |
| # Enable SD Card PCIe 7 using clk 3 |
| register "pch_pcie_rp[PCH_RP(7)]" = "{ |
| .clk_src = 3, |
| .clk_req = 3, |
| .flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER, |
| }" |
| chip soc/intel/common/block/pcie/rtd3 |
| register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" |
| register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H12)" |
| register "srcclk_pin" = "3" |
| device generic 0 on end |
| end |
| end |
| device ref pch_espi on |
| chip ec/google/chromeec |
| use conn0 as mux_conn[0] |
| use conn1 as mux_conn[1] |
| device pnp 0c09.0 on end |
| end |
| end |
| device ref pmc hidden |
| chip drivers/intel/pmc_mux |
| device generic 0 on |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port1 as usb2_port |
| use tcss_usb3_port1 as usb3_port |
| device generic 0 alias conn0 on end |
| end |
| chip drivers/intel/pmc_mux/conn |
| use usb2_port2 as usb2_port |
| use tcss_usb3_port2 as usb3_port |
| device generic 1 alias conn1 on end |
| end |
| end |
| end |
| end |
| device ref tcss_xhci on |
| chip drivers/usb/acpi |
| device ref tcss_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref tcss_usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref tcss_usb3_port2 on |
| probe DB_USB DB_C_A |
| probe DB_USB DB_C_A_LTE |
| end |
| end |
| end |
| end |
| end |
| device ref xhci on |
| register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # USB2_A1 |
| register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # WFC |
| register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN |
| register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN |
| register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/3 Type A port A1 |
| |
| chip drivers/usb/acpi |
| device ref xhci_root_hub on |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C0 (MLB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" |
| device ref usb2_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-C Port C1 (DB)"" |
| register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" |
| device ref usb2_port2 on |
| probe DB_USB DB_C_A |
| probe DB_USB DB_C_A_LTE |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb2_port3 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb2_port4 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port5 on |
| probe DB_USB DB_C_A_LTE |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 UFC"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port6 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 WFC"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb2_port7 on |
| probe WFC WFC_PRESENT |
| end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB2 Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port8 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""CNVi Bluetooth"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| register "reset_gpio" = |
| "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" |
| device ref usb2_port10 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A0 (MLB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" |
| device ref usb3_port1 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 Type-A Port A1 (DB)"" |
| register "type" = "UPC_TYPE_USB3_A" |
| register "use_custom_pld" = "true" |
| register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" |
| device ref usb3_port2 on end |
| end |
| chip drivers/usb/acpi |
| register "desc" = ""USB3 WWAN"" |
| register "type" = "UPC_TYPE_INTERNAL" |
| device ref usb3_port3 on |
| probe DB_USB DB_C_A_LTE |
| end |
| end |
| end |
| end |
| end |
| device ref hda on |
| chip drivers/sof |
| register "spkr_tplg" = "rt1019" |
| register "jack_tplg" = "rt5682" |
| register "mic_tplg" = "_2ch_pdm0" |
| device generic 0 on end |
| end |
| end |
| end |
| end |